Skip to Content

Changes for page 12 PLC Protocol OLD

Last modified by Mora Zhou on 2024/12/05 14:53
From version 35.1
edited by Ben
on 2022/08/19 11:22
Change comment: There is no comment for this version
To version 69.1
edited by Ben
on 2022/08/29 14:09
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -85,6 +85,392 @@
85 85  
86 86  Click [OK] button to save settings and close the dialog;
87 87  
88 += Create communication with WECON PLC =
89 +
90 +== **LX3V Serial Protocol** ==
91 +
92 +Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
93 +
94 +**HMI Settings**
95 +
96 +(% class="table-bordered" %)
97 +|**Item**|**Settings**|**Note**
98 +|Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
99 +|Connection|RS422/RS485|
100 +|Baud rate|9600|
101 +|Data bit|7|
102 +|Parity|EVEN|
103 +|Stop bit|1|
104 +|PLC station No.|1|
105 +
106 +**Address List**
107 +
108 +(% class="table-bordered" %)
109 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
110 +|(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
111 +|Y|Y|Y o|0~~303237|
112 +|M|M|M d|0~~99999|
113 +|T|T|T d|0~~99999|
114 +|C|C|C d|0~~99999|
115 +|S|S|S d|0~~99999|
116 +|(% rowspan="8" %)Word|X|X|Xo|0~~303237|
117 +|Y|Y|Y o|0~~303237|
118 +|M|M|M d|0~~99999|
119 +|T|T|T d|0~~99999|
120 +|C|C|C d|0~~199|
121 +|D|D|D d|0~~7999|
122 +|S|S|S d|0~~99999|
123 +|SD|SD|SD d|8000~~9999|
124 +
125 +**Cable Wiring**
126 +
127 +* **RS485**
128 +
129 +(% style="text-align:center" %)
130 +[[image:12.PLC Protocol_html_1897d92be6948d58.png||data-xwiki-image-style-alignment="center" height="223" width="393" class="img-thumbnail"]]
131 +
132 +* **RS422**
133 +
134 +(% style="text-align:center" %)
135 +[[image:12.PLC Protocol_html_5c7fca9a70da2ee8.png||data-xwiki-image-style-alignment="center" height="247" width="389" class="img-thumbnail"]]
136 +
137 +**✎Note:**
138 +
139 +* HMI COM3 is available in PI8000 series and COM3 is in COM2(hardware PIN 7 and PIN 8) .
140 +* If PLC <= 20 points,such as LX3V-1208/LX3V-0806 PLC,PLC RS485A and RS485B mean PLC COM2 RS485+ and RS485- .PLC COM2 can support modbus. Please refer to PLC COM2 setting manual.
141 +
142 +[[https:~~/~~/drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing>>url:https://drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing]]
143 +
144 +(% class="wikigeneratedid" id="HHMIsettings" %)
145 +**HMI settings**
146 +
147 +**Download PIStudio Software**
148 +
149 +Please visit the link below to get the latest version PIstudio for HMI programming:
150 +
151 +* [[Download link>>doc:PIStudio.Download.3 Software.WebHome]]
152 +
153 +**Create a new HMI project connect with PLC**
154 +
155 +Check the link below for the video to show you how to get started with a new project
156 +
157 +* [[Video>>https://youtu.be/0FpmDZe_8U8]]
158 +
159 +For more videos, please visit our Youtube channel: [[http:~~/~~/www.youtube.com/user/Wecon2004/videos>>url:http://www.youtube.com/user/Wecon2004/videos]]
160 +
161 +**General**
162 +
163 +HMI could communicate with PLC and support many PLC protocols.  It is easy to operate and set communication parameters. This demo shows how to make a communication with PLC device, use WECON LX3V Series PLC as an example.
164 +
165 +**Protocol settings**
166 +
167 +The communication between two devices requires a protocol. The following contents show the steps of protocol settings.
168 +
169 +Please select the protocol, when creating a new project.
170 +
171 +1. Select the COM port for communication;
172 +1. PLC type: It means PLC brand, like WECON;
173 +1. PLC model: It shows the model of PLC, such as LX3V;
174 +
175 +(% style="text-align:center" %)
176 +[[image:image-20220819093729-1.png]]
177 +
178 +If you want to change the protocol for existing project, please click [Program] → [Communication] to open the [Communication] windows, shown as the following figure.
179 +
180 +(% style="text-align:center" %)
181 +[[image:image-20220819093729-2.png]]
182 +
183 +
184 +The steps to change the protocol for project are as follows.
185 +
186 +1. Click [Setting] to open the [Communication device] window;
187 +1. Select communication port, such as COM1;
188 +1. Select Serial port for communication, such as RS422;
189 +1. Select device type (device brand), such as WECON;
190 +1. Select the protocol for communication, such as WECON LX3V;
191 +
192 +(% style="text-align:center" %)
193 +[[image:image-20220819093729-3.png]]
194 +
195 +**Parameter settings**
196 +
197 +The parameters settings are in [Communication] window, shown as following below.
198 +
199 +1. Click [Setting] to open the [COM port setting] window;
200 +1. Set the parameters such as [connection], [Baud rate] and so on;
201 +
202 +(% style="text-align:center" %)
203 +[[image:image-20220819093729-4.png||height="636" width="818"]]
204 +
205 +(% start="3" %)
206 +1. Click [Setting] to open [Timeout] setting window, you could set the parameters according your requirements, or just use the default value.
207 +
208 +(% style="text-align:center" %)
209 +[[image:image-20220819093729-5.png]]
210 +
211 +**Set PLC address in HMI screen**
212 +
213 +1. Place the objects to HMI screen;
214 +1. Double-click the object to open the setting window;
215 +1. Click “Edit” to open the address setting windows;
216 +1. Connection: select the serial port in HMI;
217 +1. Address type: All the PLC address types will be display in this list, such as M;
218 +1. Address No.: Please input the number of this address, such as 0;
219 +
220 +[[image:image-20220819093729-6.jpeg]]
221 +
222 +**Communication cable**
223 +
224 +In order to ensure the stability of communication, please use the twisted-pair communication cable with good grounding. The following figure shows the pin out definition.
225 +
226 +(% style="text-align:center" %)
227 +[[image:image-20220819093729-7.png]]
228 +
229 +**HMI communication PLC use Modbus **
230 +
231 +* HMI setting: [[https:~~/~~/docs.we-con.com.cn/bin/view/PIStudio/12.PLC%20protocols/>>https://docs.we-con.com.cn/bin/view/PIStudio/12.PLC%20protocols/]]
232 +* PLC setting: [[https:~~/~~/docs.we-con.com.cn/bin/view/PLC%20Editor/8.1.%09Communication/>>https://docs.we-con.com.cn/bin/view/PLC%20Editor/8.1.%09Communication/]]
233 +
234 +(% class="wikigeneratedid" id="HPLCsettings" %)
235 +**PLC settings**
236 +
237 +**Download PLC Software**
238 +
239 +Please visit below link to get the latest version PLC Editor for HMI programming
240 +
241 +* LX3V:[[Download link>>doc:PLC Editor.10 Hardware .Software.WebHome]]
242 +* LX5V:[[Download link>>doc:PLC Editor2.Download.03 Software.WebHome]]
243 +
244 +**Start a new PLC project**
245 +
246 +Start a new PLC project by clicking “New” on the left top corner of screen, select the PLC mode from the drop-down list.
247 +
248 +(% style="text-align:center" %)
249 +[[image:image-20220819101447-3.jpeg]]
250 +
251 +
252 +
253 +**Add a new instruction **
254 +
255 +Double click on the ladder, select the ladder symbol (instruction) from the drop-down list, then enter the address for this symbol.
256 +
257 +(% style="text-align:center" %)
258 +[[image:image-20220819105530-1.png]]
259 +
260 +You could also select the ladder symbol from the menu bar directly.
261 +
262 +[[image:image-20220819093729-11.png]]
263 +
264 +[[image:image-20220819093729-12.png]]
265 +
266 +**Add comment to PLC program**
267 +
268 +(% style="text-align:center" %)
269 +[[image:image-20220819105630-3.png]]
270 +
271 +**Add the statement to PLC program**
272 +
273 +Add the statement by single click on “Statement”, when finished, single click on “Statement” again to go back to Ladder edit.
274 +
275 +(% style="text-align:center" %)
276 +[[image:image-20220819105644-4.png]]
277 +
278 +**Compile **
279 +
280 +You need to compile the PLC program before downloading or running Off-line simulator. The background color will be changed from purple to white when there is no error.
281 +
282 +[[image:image-20220819093729-15.png]]
283 +
284 +**Download setting **
285 +
286 +Click on “Transfer Setup” to select download mode.
287 +
288 +[[image:image-20220820150853-1.png]]**Download PLC program to PLC**
289 +
290 +Quick select the parameters and main program of PLC program, then download to PLC, “Yes”-”Yes”-”OK”
291 +
292 +[[image:image-20220819093729-17.png]]
293 +
294 +**Upload PLC program from PLC**
295 +
296 +Read the PLC program from PLC to computer.
297 +
298 +[[image:image-20220819093729-18.png]]
299 +
300 +**Device monitor**
301 +
302 +Monitor the value of certain address in PLC, double click “Current value” to change the value in this address.
303 +
304 +[[image:image-20220819093730-19.png]]
305 +
306 +**Online monitor**
307 +
308 +Monitor the each address in PLC by online monitor. Changing the state or value in PLC is also allowd.
309 +
310 +[[image:image-20220819093730-20.png]]
311 +
312 +**Monitor edit**
313 +
314 +In this mode, you could edit the PLC program during PLC is running. 
315 +
316 +
317 +(% style="text-align:center" %)
318 +[[image:image-20220819105928-9.png||height="229" width="669"]]
319 +
320 +== **LX5V Serial Protocol** ==
321 +
322 +This example introduces the establishment of serial port communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
323 +
324 +**Software configuration of PLC**
325 +
326 +**1）PLC programming software**
327 +
328 +[[image:image-20220810164710-1.png]]
329 +
330 +**2）New PLC project**
331 +
332 +Click New Project and select the PLC model.
333 +
334 +[[image:image-20220810172412-1.png]]
335 +
336 +
337 +**3）Set Serial port parameters**
338 +
339 +Follow the steps below to configure Serial port parameters
340 +
341 +Baud rate：115200
342 +
343 +Data bit：8
344 +
345 +Stop bit：1
346 +
347 +Parity：No verification
348 +
349 +[[image:image-20220810165759-3.png]]
350 +
351 +
352 +**4）Registers list**
353 +
354 +[[image:image-20220811102219-3.png]]
355 +
356 +
357 +**HMI software configuration**
358 +
359 +**1）HMI programming software**
360 +
361 + [[image:image-20220810171237-4.png]]
362 +
363 +**2）New HMI project**
364 +
365 +Click New Project and select the HMI model.
366 +
367 +[[image:image-20220810172010-5.png]]
368 +
369 +**3）Set communication port parameters**
370 +
371 +Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
372 +
373 +Baud rate：115200
374 +
375 +Data bit：8
376 +
377 +Stop bit：1
378 +
379 +Parity：No verification
380 +
381 +
382 +[[image:image-20220811104012-1.png]]
383 +
384 +
385 +**hardware connection**
386 +
387 +**1）Hardware wiring diagram**
388 +
389 +This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
390 +
391 +[[image:image-20220811103005-4.png]]
392 +
393 +
394 +[[image:image-20220811103227-7.png]]
395 +
396 +The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
397 +
398 +== **LX5V-N Ethernet protocol** ==
399 +
400 +(% id="cke_bm_147709S" style="display:none" %) (%%)This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
401 +
402 +
403 +**Software configuration of PLC**
404 +
405 +**1）PLC programming software**
406 +
407 +[[image:image-20220810164710-1.png]]
408 +
409 +**2）New PLC project**
410 +
411 +Click New Project and select the PLC model.
412 +
413 +[[image:image-20220811115454-1.png]]
414 +
415 +
416 +**3）Set Ethernet port parameters**
417 +
418 +Follow the steps below to configure Ethernet parameters
419 +
420 +PLC IP address：192.168.39.200
421 +
422 +default gateway：192.168.39.1
423 +
424 +subnet mask：255.255.255.0
425 +
426 +[[image:image-20220811140530-2.png]]
427 +
428 +
429 +**4）Registers list**
430 +
431 +[[image:image-20220811102219-3.png]]
432 +
433 +
434 +**HMI software configuration**
435 +
436 +**1）HMI programming software**
437 +
438 + [[image:image-20220810171237-4.png]]
439 +
440 +**2）New HMI project**
441 +
442 +Click New Project and select the HMI model.
443 +
444 +[[image:image-20220810172010-5.png]]
445 +
446 +**3）Set communication port parameters**
447 +
448 +Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
449 +
450 +HMI IP address：192.168.39.201
451 +
452 +default gateway：192.168.39.1
453 +
454 +subnet mask：255.255.255.0
455 +
456 +[[image:image-20220811170753-2.png]]
457 +
458 +Next, click Communication Settings to configure the IP of the HMI communication object.
459 +
460 +[[image:image-20220811163047-1.png]]
461 +
462 +**hardware connection**
463 +
464 +**1）Hardware wiring diagram**
465 +
466 +This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
467 +
468 +[[image:image-20220811170248-1.png]]
469 +
470 +The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
471 +
472 += =
473 +
88 88  = **Allen-Bradley** =
89 89  
90 90  == **FreeTag Ethernet/IP (CompactLogix)** ==
... ... @@ -193,7 +193,7 @@
193 193  * **Word address S:** The word address ranges from 0 to 255 (decimal).
194 194  * **Word address TS:** The address ranges from 000.0 to ffff. The first and second f from left to right represents the block number (hexadecimal); The third and fourth f from left to right represent the word address (hexadecimal).
195 195  
196 -**✎Note: **Register address TP, CS, CP, N, F and TS address edit tare he same. D indicates decimal, and F indicates hexadecimal. Different PLC models may support different registers. See the following table.
582 +**✎Note: **Register address TP, CS, CP, N, F and TS address edit are same. D indicates decimal, and F indicates hexadecimal. Different PLC models may support different registers. See the following table.
197 197  
198 198  |(% style="width:393px" %)**PLC bit address type**|(% style="width:350px" %)**Address format**|(% style="width:333px" %)**Address range**
199 199  |(% style="width:393px" %)I|(% style="width:350px" %)dd.dd|(% style="width:333px" %)I 0.0 ~~ 255.15
... ... @@ -2263,219 +2263,8 @@
2263 2263  
2264 2264  **✎Note:** COM3 only available in PI8000/PI9000 series.
2265 2265  
2266 -= **WECON PLC** =
2652 += =
2267 2267  
2268 -Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
2269 -
2270 -**HMI Settings**
2271 -
2272 -(% class="table-bordered" %)
2273 -|**Item**|**Settings**|**Note**
2274 -|Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
2275 -|Connection|RS422/RS485|
2276 -|Baud rate|9600|
2277 -|Data bit|7|
2278 -|Parity|EVEN|
2279 -|Stop bit|1|
2280 -|PLC station No.|1|
2281 -
2282 -**Address List**
2283 -
2284 -(% class="table-bordered" %)
2285 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
2286 -|(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
2287 -|Y|Y|Y o|0~~303237|
2288 -|M|M|M d|0~~99999|
2289 -|T|T|T d|0~~99999|
2290 -|C|C|C d|0~~99999|
2291 -|S|S|S d|0~~99999|
2292 -|(% rowspan="8" %)Word|X|X|Xo|0~~303237|
2293 -|Y|Y|Y o|0~~303237|
2294 -|M|M|M d|0~~99999|
2295 -|T|T|T d|0~~99999|
2296 -|C|C|C d|0~~199|
2297 -|D|D|D d|0~~7999|
2298 -|S|S|S d|0~~99999|
2299 -|SD|SD|SD d|8000~~9999|
2300 -
2301 -**Cable Wiring**
2302 -
2303 -* **RS485**
2304 -
2305 -(% style="text-align:center" %)
2306 -[[image:12.PLC Protocol_html_5e9a81a14106da9e.png||data-xwiki-image-style-alignment="center" height="223" width="392" class="img-thumbnail"]]
2307 -
2308 -(% style="text-align:center" %)
2309 -[[image:12.PLC Protocol_html_1897d92be6948d58.png||data-xwiki-image-style-alignment="center" height="223" width="393" class="img-thumbnail"]]
2310 -
2311 -* **RS422**
2312 -
2313 -(% style="text-align:center" %)
2314 -[[image:12.PLC Protocol_html_5c7fca9a70da2ee8.png||data-xwiki-image-style-alignment="center" height="247" width="389" class="img-thumbnail"]]
2315 -
2316 -**✎Note:**
2317 -
2318 -* HMI COM3 is available in PI8000 series and COM3 is in COM2(hardware PIN 7 and PIN 8) .
2319 -* If PLC <= 20 points,such as LX3V-1208/LX3V-0806 PLC,PLC RS485A and RS485B mean PLC COM2 RS485+ and RS485- .PLC COM2 can support modbus. Please refer to PLC COM2 setting manual.
2320 -
2321 -[[https:~~/~~/drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing>>url:https://drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing]]
2322 -
2323 -
2324 -== HMI and Wecon LX5V serial communication ==
2325 -
2326 -This example introduces the establishment of serial port communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
2327 -
2328 -**Software configuration of PLC**
2329 -
2330 -**1）PLC programming software**
2331 -
2332 -[[image:image-20220810164710-1.png]]
2333 -
2334 -**2）New PLC project**
2335 -
2336 -Click New Project and select the PLC model.
2337 -
2338 -[[image:image-20220810172412-1.png]]
2339 -
2340 -
2341 -**3）Set Serial port parameters**
2342 -
2343 -Follow the steps below to configure Serial port parameters
2344 -
2345 -Baud rate：115200
2346 -
2347 -Data bit：8
2348 -
2349 -Stop bit：1
2350 -
2351 -Parity：No verification
2352 -
2353 -[[image:image-20220810165759-3.png]]
2354 -
2355 -
2356 -**4）Registers list**
2357 -
2358 -[[image:image-20220811102219-3.png]]
2359 -
2360 -
2361 -**HMI software configuration**
2362 -
2363 -**1）HMI programming software**
2364 -
2365 - [[image:image-20220810171237-4.png]]
2366 -
2367 -**2）New HMI project**
2368 -
2369 -Click New Project and select the HMI model.
2370 -
2371 -[[image:image-20220810172010-5.png]]
2372 -
2373 -**3）Set communication port parameters**
2374 -
2375 -Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
2376 -
2377 -Baud rate：115200
2378 -
2379 -Data bit：8
2380 -
2381 -Stop bit：1
2382 -
2383 -Parity：No verification
2384 -
2385 -
2386 -[[image:image-20220811104012-1.png]]
2387 -
2388 -
2389 -**hardware connection**
2390 -
2391 -**1）Hardware wiring diagram**
2392 -
2393 -This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
2394 -
2395 -[[image:image-20220811103005-4.png]]
2396 -
2397 -
2398 -[[image:image-20220811103227-7.png]]
2399 -
2400 -The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
2401 -
2402 -(% class="wikigeneratedid" %)
2403 -== ==
2404 -
2405 -== HMI and Wecon LX5V-N Ethernet communication ==
2406 -
2407 -(% id="cke_bm_147709S" style="display:none" %) (%%)This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
2408 -
2409 -
2410 -**Software configuration of PLC**
2411 -
2412 -**1）PLC programming software**
2413 -
2414 -[[image:image-20220810164710-1.png]]
2415 -
2416 -**2）New PLC project**
2417 -
2418 -Click New Project and select the PLC model.
2419 -
2420 -[[image:image-20220811115454-1.png]]
2421 -
2422 -
2423 -**3）Set Ethernet port parameters**
2424 -
2425 -Follow the steps below to configure Ethernet parameters
2426 -
2427 -PLC IP address：192.168.39.200
2428 -
2429 -default gateway：192.168.39.1
2430 -
2431 -subnet mask：255.255.255.0
2432 -
2433 -[[image:image-20220811140530-2.png]]
2434 -
2435 -
2436 -**4）Registers list**
2437 -
2438 -[[image:image-20220811102219-3.png]]
2439 -
2440 -
2441 -**HMI software configuration**
2442 -
2443 -**1）HMI programming software**
2444 -
2445 - [[image:image-20220810171237-4.png]]
2446 -
2447 -**2）New HMI project**
2448 -
2449 -Click New Project and select the HMI model.
2450 -
2451 -[[image:image-20220810172010-5.png]]
2452 -
2453 -**3）Set communication port parameters**
2454 -
2455 -Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
2456 -
2457 -HMI IP address：192.168.39.201
2458 -
2459 -default gateway：192.168.39.1
2460 -
2461 -subnet mask：255.255.255.0
2462 -
2463 -[[image:image-20220811170753-2.png]]
2464 -
2465 -Next, click Communication Settings to configure the IP of the HMI communication object.
2466 -
2467 -[[image:image-20220811163047-1.png]]
2468 -
2469 -**hardware connection**
2470 -
2471 -**1）Hardware wiring diagram**
2472 -
2473 -This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
2474 -
2475 -[[image:image-20220811170248-1.png]]
2476 -
2477 -The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
2478 -
2479 2479  = **Printer** =
2480 2480  
2481 2481  == **TSPL label printer** ==
image-20220819093729-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +10.3 KB
Content
image-20220819093729-10.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +79.4 KB
Content
image-20220819093729-12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +147.9 KB
Content
image-20220819093729-15.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +74.6 KB
Content
image-20220819093729-17.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +115.0 KB
Content
image-20220819093729-18.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +112.1 KB
Content
image-20220819093729-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +34.1 KB
Content
image-20220819093729-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +44.2 KB
Content
image-20220819093729-4 (1).png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +82.4 KB
Content
image-20220819093729-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +82.4 KB
Content
image-20220819093729-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +6.6 KB
Content
image-20220819093729-6.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +100.2 KB
Content
image-20220819093729-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +46.9 KB
Content
image-20220819093730-19.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +122.5 KB
Content
image-20220819093730-20.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +99.6 KB
Content
image-20220819101447-3.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +56.6 KB
Content
image-20220819105530-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +1.0 MB
Content
image-20220819105630-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +1.1 MB
Content
image-20220819105644-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +942.6 KB
Content
image-20220819105928-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +72.6 KB
Content
image-20220820150853-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +171.7 KB
Content