Skip to Content

Changes for page LX3V-4LTC

Last modified by Devin Chen on 2024/11/22 09:42
From version 7.1
edited by Devin Chen
on 2024/10/09 11:36
Change comment: There is no comment for this version
To version 5.1
edited by Mora Zhou
on 2023/11/22 10:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.DevinChen
1 +XWiki.Mora
Content
... ... @@ -389,8 +389,6 @@
389 389  )))
390 390  |(% style="width:55px" %)#76~~#80|(% style="width:12px" %)#114~~#118|(% style="width:52px" %)#152~~#156|(% style="width:65px" %)#190~~#193|(% style="width:143px" %)Reserved|(% style="width:68px" %)-|(% style="width:77px" %)-|(% style="width:104px" %)-|(% style="width:348px" %)Reserved
391 391  
392 -(% class="box infomessage" %)
393 -(((
394 394  **✎Note: **
395 395  
396 396  * 0: Retentive;
... ... @@ -397,7 +397,6 @@
397 397  * X: Non-retentive;
398 398  * R: Only read is enabled;
399 399  * R/W: Both read and write are enabled;
400 -)))
401 401  
402 402  **Details of buffer memories**
403 403  
... ... @@ -460,17 +460,6 @@
460 460  
461 461  The identification code or ID number for this Special Block is read from buffer memory BFM #30 by FROM instruction. This number for the LX3V-4LTC unit is K2130. The PLC can use this ID in program to identify the special block before commencing data transfer to and from the special block.
462 462  
463 -**Power-down retention flag BFM#42**
464 -
465 -First, configure the parameters to be saved, and then set the power-down retention flag BFM#42 to 1. This enables power-down retention for the configured parameters.
466 -
467 -The operation steps are illustrated as follows:
468 -
469 -1. Set the power-down retention register to a value of 100 (e.g., BFM#52 is set to 100).
470 -1. Set the power-down retention flag BFM#42 to 1 (data is saved at this point, and BFM#42 will automatically reset to zero upon completion).
471 -1. Change the data of the power-down retention register to 1000 (e.g., BFM#52 is set to 1000).
472 -1. Power off and then power on again. At this point, check the value of the power-down retention register, which should be 100 (e.g., BFM#52 shows a value of 100)."
473 -
474 474  **Error flag BFM #43, BFM#81, BFM#119, BFM#157 (Temperature control is stopped)**
475 475  
476 476  (((
... ... @@ -613,8 +613,6 @@
613 613  |(% style="width:88px" %)11|(% style="width:238px" %)Alarm for Upper/lower limit deviation with wait|(% style="width:608px" %)Alarms if absolute deviation (= Measured value (PV) – Set value (SV)) is less than value of alarm. However, measured value is ignored at the start of system.|(% style="width:141px" %)+Input width
614 614  )))
615 615  
616 -(% class="box infomessage" %)
617 -(((
618 618  **✎Note: **
619 619  
620 620  * Input range: it is from the lower threshold to the upper threshold of input value
... ... @@ -621,7 +621,6 @@
621 621  * Input width: Width from the lower threshold to the upper threshold of input value (Input width = Upper threshold value - Lower threshold value).
622 622  * ±Input width: it could be positive and negative.
623 623  * + Input width: it could be positive only.
624 -)))
625 625  
626 626  **Alarm dead zone setting**
627 627