| ... |
... |
@@ -1,0 +1,194 @@ |
|
1 |
+= **Introduction** = |
|
2 |
+ |
|
3 |
+ |
|
4 |
+ |
|
5 |
+LX6V-4PT (4-channal analog inputs), used for the acquisition of thermocouple input analog signals. Suitable for Wecon LX6 series PLC and LX6V-EM□-ECAT coupler. |
|
6 |
+ |
|
7 |
+LX6V-EM□-ECAT firmware version that supports this module: V2.022 and above, the corresponding XML version: 1.3 and above. |
|
8 |
+ |
|
9 |
+Upper computer software version that supports this module: 2.6. 236 and above, PLC firmware version:2.321. 1032 and above. |
|
10 |
+ |
|
11 |
+ |
|
12 |
+**✎Note: **The total power of expansion modules connected to LX6 series PLC and LX6V-EM□-ECAT cannot be greater than 48W. |
|
13 |
+ |
|
14 |
+1. **Appearance and terminal description** |
|
15 |
+11. **Appearance and size** |
|
16 |
+ |
|
17 |
+ |
|
18 |
+ |
|
19 |
+[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml8120\wps5.png]] |
|
20 |
+ |
|
21 |
+① LED; ② Terminal; ③ Expansion module interface; ④ Mounting hole: 2 places (Φ4.5); |
|
22 |
+ |
|
23 |
+⑤ DIN rail buckle. |
|
24 |
+ |
|
25 |
+ |
|
26 |
+1. |
|
27 |
+11. **Terminal description** |
|
28 |
+ |
|
29 |
+The 4PT expansion module terminal are arranged as follows: |
|
30 |
+ |
|
31 |
+ |
|
32 |
+|**Module model**|(% colspan="2" %)**Terminal arrangement** |
|
33 |
+|LX6V-4PT| |[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml8120\wps7.png]] |
|
34 |
+ |
|
35 |
+ |
|
36 |
+ |
|
37 |
+1. |
|
38 |
+11. **Installation** |
|
39 |
+ |
|
40 |
+Please install the end cover on the right side of the last expansion module, align it with the module interface slot and connect it, as shown in the figure below: |
|
41 |
+ |
|
42 |
+[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml8120\wps8.png]] |
|
43 |
+ |
|
44 |
+ |
|
45 |
+1. |
|
46 |
+11. **Indicator** |
|
47 |
+ |
|
48 |
+The 4PT expansion module LED is shown below: |
|
49 |
+ |
|
50 |
+|**Indicator**|**Description** |
|
51 |
+|PWR|((( |
|
52 |
+Power indicator |
|
53 |
+ |
|
54 |
+1. Lights on: The module is powered on normally |
|
55 |
+1. Lights out: The module is not powered on or the module is abnormal |
|
56 |
+))) |
|
57 |
+|LINK|((( |
|
58 |
+Communication indicator |
|
59 |
+ |
|
60 |
+1. Lights on: Data interaction is normal |
|
61 |
+1. Lights out: Data interaction is abnormal or stopped |
|
62 |
+))) |
|
63 |
+|L1+/L2+/L3+/L4 +|((( |
|
64 |
+Channel indicator |
|
65 |
+ |
|
66 |
+1. Lights on: Channel enable |
|
67 |
+1. Lights out: Channel disable |
|
68 |
+1. Slow flash: Channel not calibrated |
|
69 |
+1. Fast flash: Channel abnormal (refer to status code for details) |
|
70 |
+))) |
|
71 |
+|L1-/L2-/L3-/L4-|N/A |
|
72 |
+|I1+/I2+/I3+/I4 +|N/A |
|
73 |
+ |
|
74 |
+ |
|
75 |
+ |
|
76 |
+ |
|
77 |
+1. **Parameter Specification** |
|
78 |
+11. **Input Specification** |
|
79 |
+ |
|
80 |
+|**Item**|**Description** |
|
81 |
+|Input channel|4 |
|
82 |
+|Digital resolution|16 bit |
|
83 |
+|Sensitivity|0.01℃, 0.01℉ |
|
84 |
+|Input terminal|Thermocouple input |
|
85 |
+|Sensor type|PT100, PT1000, CU50 |
|
86 |
+|Accuracy (normal temperature 25℃)|Full range ± 0.2% |
|
87 |
+|Accuracy (working temperature -20℃ to 55℃)|Full range ± 0. 3% |
|
88 |
+|Isolation or not|I/O terminals are isolated from power supply, channels are not isolated |
|
89 |
+|Overlimit disconnection detection|Support |
|
90 |
+|Power consumption|< 1.1W |
|
91 |
+|Power supply|Power supply via interface, DC24V±10%, 40mA |
|
92 |
+ |
|
93 |
+ |
|
94 |
+ |
|
95 |
+1. |
|
96 |
+11. **Environmental specification** |
|
97 |
+11. |
|
98 |
+**Software Specifications** |
|
99 |
+ |
|
100 |
+|**Item**|(% colspan="5" %)**Specification** |
|
101 |
+|Usage environment|(% colspan="5" %)No corrosive, combustible gas, no large amount of conductive dust |
|
102 |
+|Environment temperature|(% colspan="5" %)((( |
|
103 |
+Working temperature: 0℃ to 55℃ |
|
104 |
+ |
|
105 |
+Storage temperature: -20℃ to 70℃ |
|
106 |
+))) |
|
107 |
+|Environment humidity|(% colspan="5" %)((( |
|
108 |
+Working humidity: 10% to 90%RH (no condensation) |
|
109 |
+ |
|
110 |
+Storage humidity: ≤ 90% RH (no condensation) |
|
111 |
+))) |
|
112 |
+|Installation|(% colspan="5" %)Snap mount on DIN46277 (width 35mm) rail or direct positioning hole mount |
|
113 |
+|(% rowspan="6" %)Vibration resistance|(% colspan="5" %)According to JISC0040 standard |
|
114 |
+|Installation|Frequency|Acceleration|Amplitude|(% rowspan="5" %)((( |
|
115 |
+X, Y, Z |
|
116 |
+ |
|
117 |
+10 times in each of three directions |
|
118 |
+ |
|
119 |
+(80 minutes in each direction) |
|
120 |
+))) |
|
121 |
+|(% rowspan="2" %)DIN rail installation|10 to 57Hz|~-~-|0.035mm |
|
122 |
+|57 to 150Hz|4.9m/S^^2^^|~-~- |
|
123 |
+|(% rowspan="2" %)Direct installation|10 to 57Hz|~-~-|0.075mm |
|
124 |
+|57 to 150Hz|9.8m/S^^2^^|~-~- |
|
125 |
+|Shock resistance|(% colspan="5" %)((( |
|
126 |
+Compliant with JISC0041 standard |
|
127 |
+ |
|
128 |
+(147 m/S^^2^^, action time 11ms, three sinusoidal half-wave pulses in each of X, Y, and Z directions) |
|
129 |
+))) |
|
130 |
+|EMC immunity level|(% colspan="5" %)Zone B (per IEC 61131-2) |
|
131 |
+|Altitude requirements|(% colspan="5" %)≤2000m (80 kPa) |
|
132 |
+|Protection level|(% colspan="5" %)IP20 |
|
133 |
+|Grounding|(% colspan="5" %)Not co-located with the strong current system |
|
134 |
+ |
|
135 |
+|**Item**|**Specification** |
|
136 |
+|Input PDO data volume|Maximum 24 byte |
|
137 |
+|Diagnostic reporting function configuration|Support |
|
138 |
+|Diagnostic detection enable configuration|Support overlimit and disconnection detection |
|
139 |
+|Sensor type configuration|((( |
|
140 |
+Support thermal resistor type: PT100, PT1000, CU50, default is |
|
141 |
+ |
|
142 |
+PT100 thermal resistance |
|
143 |
+))) |
|
144 |
+|Filter time|0s to 100s (can be configured by software, default 5s) |
|
145 |
+|Overflow detection|Support |
|
146 |
+|Overlimit detection enable configuration|Support |
|
147 |
+|Independent channel configuration|Support |
|
148 |
+|Temperature offset enable configuration|Support |
|
149 |
+|Temperature offset configuration range|-300 to +300, temperature unit |
|
150 |
+|Display mode|Celsius (℃), Fahrenheit (℉) |
|
151 |
+|Display sensitivity|0.01℃, 0.01℉ |
|
152 |
+|Sample refresh|Refresh asynchronously according to the sampling time, do not require synchronization refresh according to the bus cycle |
|
153 |
+|Stop mode|Output according to the maximum value, no more refresh |
|
154 |
+|Disconnected or overlimit|Output according to the maximum value, no more refresh |
|
155 |
+|System diagnostics|System power abnormality |
|
156 |
+|Channel diagnosis|Over upper limit alarm, over lower limit alarm, disconnection alarm, overflow alarm |
|
157 |
+|Configuration diagnostics|Configuration error identification, channel parameter configuration error |
|
158 |
+ |
|
159 |
+ |
|
160 |
+ |
|
161 |
+ |
|
162 |
+1. |
|
163 |
+11. **Accuracy calculation** |
|
164 |
+ |
|
165 |
+Within the working temperature range, when the temperature change rate is less than 0.3°C/min, the accuracy of this product = ADC sampling accuracy + line resistance error + contact impedance error. According to the measure principle, it is necessary to wait for the module to be powered on for 45 minutes before measuring. |
|
166 |
+ |
|
167 |
+|**Sensor type**|**Detection range**|**Accuracy** |
|
168 |
+|PT100|((( |
|
169 |
+-200.0℃ to +850.0℃， |
|
170 |
+ |
|
171 |
+-328.0℉ to +1562.0℉ |
|
172 |
+)))|((( |
|
173 |
+T < 300°C: ±0.6℃ |
|
174 |
+ |
|
175 |
+300℃ ≤ T ≤ 700℃: ±1.4℃ |
|
176 |
+ |
|
177 |
+T > 700°C: ±1.7℃ |
|
178 |
+))) |
|
179 |
+|PT1000|((( |
|
180 |
+-200.0℃ to +850.0℃， |
|
181 |
+ |
|
182 |
+-328.0℉ to +1562.0℉ |
|
183 |
+)))|((( |
|
184 |
+T < 300°C: ±0.6℃ |
|
185 |
+ |
|
186 |
+300℃ ≤ T ≤ 700℃: ±1.4℃ |
|
187 |
+ |
|
188 |
+T > 700 °C: ±1.7℃ |
|
189 |
+))) |
|
190 |
+|CU50|((( |
|
191 |
+-50.0℃ to + 150.0℃， |
|
192 |
+ |
|
193 |
+-58.0℉ to +302.0℉ |
|
194 |
+)))|-50℃ ≤ T ≤ 150℃: ±0.3℃ |
