12 HMI internal registers

= **Introduction** =

HMI provide four types of HMI address for user. You can use them as temporary variables of the program. The use is consistent with the way access to the PLC register. You could also reference through the address, PIStudio provides three types of such memory.

4

5

*HSW, HDW, HUW, HAW are word address, HSX, HDX, HUX, HAX are bit address.

6

7

1. **System data area (HSW): **A special register defined by the system.

8

1. **Data storage area (HDW/HDX): **Users store user data.

9

1. **System data area (HUW): **A special register defined by the system.

10

1. **System Data (HAW)**: System register used for power-off save.

11

1. **Recipe index area (RPW): **System register used for recipe index.

12

13

HMI internal registers are divided into bit address and word address, which can be accessed in two ways (take HDW as an example).

14

15

1. Access as word with the prefix "HDW".

16

17

* HDW0 means the 1st word of system data area. HDW1 means the 2nd word of system data area.

18

19

(% start="2" %)

20

1. Access as bit with the prefix "HDX". The number before "." i". The number before Access in bit with the prefix "HD". The number before Access in bit with the prefix "HDX". The number before "." indicates the number of the word. The number after "." indicates the bit number of the word.

21

22

* HDX1020.12 means to access the system data area in bit mode, the specific location is the 13th bit of the 1020 word.

**✎Note:**

* Addresses in HDX are the bits from words in HDW, so be careful when using addresses. For example, HDX1020.12 is the 13th bit to access the 1020 word. The value of this bit is the same as that of the word accessed through HDW001020. The 13th bit of this word is actually the same bit as HDX1020.12.

27

* The address of the bit address HDX is with a decimal point while word addresses are integers.

28

29

= **Data storage area (HDW/HDX)** =

30

31

It is used to save the temporary data of project.

32

33

1. Access as word, and serial number range is from HDW0 to HDW299999.

34

1. Access as bit, and serial number range is from HDX0.0 to HDX299999.15.

35

36

= **Power-down save area (HAW/HAX)** =

37

38

It is system registers used for power-off save.

39

40

1. Access as word, and serial number range is from HAW0 to HAW199999.

41

1. Access as bit, and serial number range is from HAX0.0 to HAX199999.15.

**✎Note:**

* HAW/HAX is power-down retention. The register of this type is able to save the data before the power-down.

46

* To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save addre

47

48

= **Recipe index area (RPW)** =

49

50

It is system recipe data power-off save register. The range is from RPW000000 to RPW990450.

**✎Note:**

* RPW is power-down retention. The register of this type is able to save the data before the power-down.

55

* To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save addre

56

57

= **Single user data area (HUW/HUX)** =

58

59

It is used for system special registers (reserved by system).

60

61

1. Access as word, and serial number range is from HUW0 to HUW199999.

62

1. Access as bit, and serial number range is from HUX0.0 to HUX199999.15.

**✎Note:**

* HUW/HUX is a system special register, so please check the system special register list during use. Please use the address specified in the table and do not use the address which is not mentioned in the table.

67

68

(% class="table-bordered" %)

69

|=**Special register address**|=**Description**|=**Function**

70

|=HUW0|Screen switch|A single terminal controls the screen switching, and all terminals do not affect each other.

71

|=HUW110~~HUW119|(% rowspan="26" %)Addresses of the built-in keyboard|The T9 input method stores the selected seria number length

72

|=HUW120~~HUW129|The T9 input method stores the selected Chinese Pinyin length

73

|=HUW135|Input method: first input

74

|=HUW136|Button: T9 Chinese Pinyin page

75

|=HUW137|Button: T9 Chinese characters page

76

|=HUW138|Button: symbol

77

|=HUW139|Button: switch

78

|=HUW140|Button: Chinese characters 1

79

|=HUW142|Button: Chinese characters 2

80

|=HUW144|Button: Chinese characters 3

81

|=HUW146|Button: Chinese characters 4

82

|=HUW148|Button: Chinese characters 5

83

|=HUW150|Button: Chinese characters 6

84

|=HUW152|Button: Chinese characters 7

85

|=HUW154|Button: Chinese characters 8

86

|=HUW156|Button: Chinese characters 9

87

|=HUW158|Button: Chinese characters 10

88

|=HUW160~~HUW169|Button: Chinese Pinyin 1

89

|=HUW170~~HUW179|Button: Chinese Pinyin 2

90

|=HUW180~~HUW189|Button: Chinese Pinyin 3

91

|=HUW190~~HUW199|Button: Chinese Pinyin 4

92

|=HUW200~~HUW699|Input method cache length

93

|=HUW700~~HUW749|Minimum value of the input method

94

|=HUW750~~HUW799|Maximum value of the input method

95

|=HUW800|Case switching of the input method

96

|=HUW801~~HUW900|Input method format cache length

97

|=HUW1000|(% rowspan="12" %)Addresses of user permission|OK (Sign in)

98

|=HUW1001|Result of operation

99

|=HUW1002~~1005|Old password

100

|=HUW1006~~1009|New password

101

|=HUW1010~~1013|Confirm password

102

|=HUW1014~~1029|New user name

103

|=HUW1030~~1157|States information of user permission

104

|=HUW1158~~1335|User name (Only or drop-down list object)

105

|=HUW1336~~1345|User name description or note

106

|=HUW1347|Hidden function configurations

107

|=HUW1348|Permission settings

108

|=HUW1349|Current user name

109

|=HUW1382|User sign in way|(((

110

* 0: Select the user name from drop-down list object for signing in

111

* 1: Enter the user name in Character Input/Display object for signing in (HUW1014)

112

)))

113

|=HUW1400|Time interval from last operation|(((

114

Shows how long the touch screen has not been clicked, in seconds. 32-bit unsigned integer

115

116

**✎Note:** Clicking by different users will only clear the corresponding register of the currently operating terminal, and the registers on other terminals (such as mobile phones, computers) will not be cleared.

117

)))

118

|=HUW1402|Keyboard note|It saves the text information of the keyboard notes when clicking object(HUW1402-HUW1433)

119

|=HUW1436|Current object level|Indicate current object security level

120

121

= **Special data area (HSW/HSX)** =

122

123

It is used for system special registers (reserved by system).

124

125

1. Access as word, and serial number range is from HSW0 to HSW49999. (HSW10000 to HSW19999 are the power-off storage areas)

126

1. Access as bit, and serial number range is from HSX0.0 to HSX49999.15.

**✎Note:**

* HSW / HSX are a system special register, so please check the system special register list during use. Please use the address specified in the table and do not use the address which is not mentioned in the table.

131

* To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save address.

132

133

(% class="table-bordered" style="width:1024px" %)

134

|=(% scope="row" style="width: 160px;" %)**Address**|=(% style="width: 282px;" %)**Function**|=(% style="width: 452px;" %)**Description**

135

|=(% style="width: 160px;" %)HSW0|(% style="width:282px" %)Language switch|(% style="width:452px" %)Multiple language could be set in the project, HMI support maximum 8 languages. (Power-down save supported)

136

|=(% style="width: 160px;" %)HSW1|(% style="width:282px" %)Beep frequency|(% style="width:452px" %)Frequency range: 0~~4000

137

|=(% style="width: 160px;" %)HSW2|(% style="width:282px" %)Beep volume|(% style="width:452px" %)Volume range: 0~~80

138

|=(% style="width: 160px;" %)HSW3|(% style="width:282px" %)Beep time|(% style="width:452px" %)Unit: ms

139

|=(% style="width: 160px;" %)HSW4|(% style="width:282px" %)Beep whether enable or not|(% style="width:452px" %)(((

* =0: Enable.

* =1: Disable.

)))

|=(% style="width: 160px;" %)HSW5|(% style="width:282px" %)(((

144

Alarm indicator

145

)))|(% style="width:452px" %)(((

146

* =0: Currently no alarm or all alarms have been off.

147

* =1: Currently alarm(s) still keep in on.

148

)))

149

|=(% style="width: 160px;" %)HSW6~~HSW7|(% style="width:282px" %)Number of alarms|(% style="width:452px" %)The number of alarm (it also includes the records of alarm confirmed)

150

|=(% style="width: 160px;" %)HSW8|(% style="width:282px" %)Number of unconfirmed history alarm|(% style="width:452px" %)The number of unconfirmed history alarm

151

|=(% style="width: 160px;" %)HSW9|(% style="width:282px" %)Time out tip|(% style="width:452px" %)(((

* =0: Enable

* =1: Disable

)))

|=(% style="width: 160px;" %)HSW12|(% style="width:282px" %)Screen swicth|(% style="width:452px" %)(((

156

* = 0: Only HSW control the screen switch, and the sreens of all users will switch.

157

* = 1: Only HUW control the screen switch, and all users do not affect each other.

158

)))

159

|=(% style="width: 160px;" %)HSW13|(% style="width:282px" %)Screen switch register|(% style="width:452px" %)Equal to different values, the screen jumps to the corresponding screen number of the screen.

160

|=(% style="width: 160px;" %)HSW24|(% style="width:282px" %)Reboot HMI|=(% style="width: 452px;" %)1: Reboot

161

|=(% style="width: 160px;" %)HSW28|(% style="width:282px" %)Local time: year|(% style="width:452px" %)Range: 0~~9999 (system reserved)

162

|=(% style="width: 160px;" %)HSW29|(% style="width:282px" %)Local time: month|(% style="width:452px" %)Range: 01~~12 (system reserved)

163

|=(% style="width: 160px;" %)HSW30|(% style="width:282px" %)Local time: day|(% style="width:452px" %)Range: 01~~31 (system reserved)

164

|=(% style="width: 160px;" %)HSW31|(% style="width:282px" %)Local time: hour|(% style="width:452px" %)Range: 0~~23 (system reserved)

165

|=(% style="width: 160px;" %)HSW32|(% style="width:282px" %)Local time: minute|(% style="width:452px" %)Range: 0~~59 (system reserved)

166

|=(% style="width: 160px;" %)HSW33|(% style="width:282px" %)Local time: second|(% style="width:452px" %)Range: 0~~59 (system reserved)

167

|=(% style="width: 160px;" %)HSW34|(% style="width:282px" %)Local time: week|(% style="width:452px" %)(((

* =0: Sunday.

* =1: Monday.

* =2: Tuesday.

* =3: Wednesday.

* =4: Thursday.

* =5: Friday.

* =6: Saturday.

)))

|=(% style="width: 160px;" %)HSW134|(% style="width:282px" %)(((

177

Whether the Script is read through

178

179

180

)))|(% style="width:452px" %)(((

181

**✎Note:** If want to read-only or write-only, please enable this settings.

182

183

* =0: Read from HMI cache(Default)

184

* =1: Read from PLC directly

185

)))

186

|=(% style="width: 160px;" %)HSW135|(% style="width:282px" %)Confirm installment password|(% style="width:452px" %)Confirm button for installment password

187

|=(% style="width: 160px;" %)HSW151|(% style="width:282px" %)Installment due|(% style="width:452px" %)Number of days to installment due

188

|=(% style="width: 160px;" %)HSW185~~200|(% style="width:282px" %)Installment password|(% style="width:452px" %)Enter installment password

189

|=(% style="width: 160px;" %)HSW242|(% style="width:282px" %)(((

190

Prompt result of recipe operation

191

192

* Upload: Data is written from address to file

193

* Download: Data is written from a file to an address

194

)))|(% style="width:452px" %)(((

195

* =1: Download recipe, start

196

* =2: Download recipe, execution error

197

* =3: Download recipe, files don't exist

198

* =4: Download recipe, members don't exist

199

* =5: Download recipe, groups don't exist

200

* =6: Download recipe, success

201

* =7: Upload recipe, start

202

* =8: Upload recipe, execution error

203

* =9: Upload recipe, files don't exist

204

* =10: Upload recipe, members don't exist

205

* =11: Upload recipe, groups don't exist

206

* =12: Upload recipe, success

207

* =13: Insert recipe, start

208

* =14: Insert recipe, execution error

209

* =15: Insert recipe, files don't exist

210

* =16: Insert recipe, members don't exist

211

* =17: Insert recipe, groups don't exist

212

* =18: Insert recipe, success

213

* =19: Delete recipe, start

214

* =20: Delete recipe, execution error

215

* =21: Delete recipe, files don't exist

216

* =22: Delete recipe, members don't exist

217

* =23: Delete recipe, groups don't exist

218

* =24: Delete recipe, success

219

* =25: Delete and sort recipe, start

220

* =26: Delete recipe and sort, execution error

221

* =27: Delete recipe and sort, files don't exist

222

* =28: Delete recipe and sort, members don't exist

223

* =29: Delete recipe and sort, groups don't exist

224

* =30: Delete recipe and sort, success

225

* =37: CSV recipe files import successfully

226

* =38: CSV recipe files import failed.

227

)))

228

|=(% style="width: 160px;" %)HSW243|(% style="width:282px" %)Prompt result of recipe index|(% style="width:452px" %)(((

229

* =31: Recipe index, start

230

* =32: Recipe index, execution error

231

* =33: Recipe index, files don't exist

232

* =34: Recipe index, members don't exist

233

* =35: Recipe index, groups don't exist

234

* =36: Recipe index, success

235

)))

236

|=(% style="width: 160px;" %)HSW521|(% style="width:282px" %)Delete graph and alarm record|(% style="width:452px" %)(((

237

* =0: No operation

238

* =1: HSX521.0=1, delete all records.

239

* =2: HSX521.1=1, delete all trend graph.

240

* =4: HSX521.2=1, delete all alarms.

241

* =16: HSX521.4=1, delete history XY plot.

242

* =32: HSX521.5=1, delete data records in SD card or flash dish;(Please make a setting which is saved to flash disk or SD card in project setting).

243

* =64: HSX521.6=1, delete alarms records in SD card or flash dish; (Please make a setting which is saved to flash disk or SD card in project setting).

244

)))

245

|=(% style="width: 160px;" %)HSW522|(% style="width:282px" %)Copy and paste the alarm/data files in flash to the USB flash disk|(% style="width:452px" %)(((

246

* =0: No operation

247

* =1: HSX522.0=1, copy all record

248

* =2: HSX522.2=1, copy history XY trend graph

249

* =8: HSX522.3=1, copy alarm record

250

* =32: HSX522.5=1, copy recipe

251

)))

252

|=(% style="width: 160px;" %)HSW523|(% style="width:282px" %)Copy and paste the alarm/data files in flash to the SD card|(% style="width:452px" %)(((

253

* =0: No operation

254

* =1: HSX523.0=1, copy all record

255

* =4: HSX523.2=1, copy history XY trend graph

256

* =8: HSX523.3=1, copy alarm record

257

)))

258

|=(% style="width: 160px;" %)HSW524|(% style="width:282px" %)Copy and paste the alarm/data files in SD card to the USB flash disk|(% style="width:452px" %)(((

259

* =0: no operation

260

* =4: HSX524.2=1, copy history XY trend graph

261

* =8: HSX524.3=1, copy alarm record

262

* =16: HSX524.4=1, copy history alarm record

263

* =32: HSX524.5=1, copy data record

264

)))

265

|=(% style="width: 160px;" %)HSW525|(% style="width:282px" %)Copy and paste the alarm/data files in USB flash disk to SD card|(% style="width:452px" %)(((

266

* =0: no operation

267

* =4: HSX525.2=1, copy history XY trend graph

268

* =8: HSX525.3=1, copy alarm record

269

* =16: HSX525.4=1, copy history alarm record

270

* =32: HSX525.5= 1, copy data record

271

)))

272

|=(% style="width: 160px;" %)HSW526|(% style="width:282px" %)Delete file list|(% style="width:452px" %)(((

273

* =0: no operation

274

* =1: HSX526.0=1, delete designated file

275

* =2: HSX526.1=1, delete all files

276

)))

277

|=(% style="width: 160px;" %)HSW527|(% style="width:282px" %)Eject USB flash disk/SD card|(% style="width:452px" %)(((

278

* =0: No operation

279

* =1: Eject USB flash disk

280

* =2: Eject SD card

281

)))

282

|=(% style="width: 160px;" %)HSW528|(% style="width:282px" %)The state of USB flash disk|(% style="width:452px" %)(((

283

* =1: USB flash disk is detected

284

* =2: Ejecting USB flash disk, please waiting…

285

* =3: USB flash disk ejected

286

)))

287

|=(% style="width: 160px;" %)HSW529|(% style="width:282px" %)The state of SD card|(% style="width:452px" %)(((

288

* =1: SD card is detected

289

* =2: Ejecting SD card, please waiting…

290

* =3: SD card ejected

291

)))

292

|=(% style="width: 160px;" %)HSW550~~849|(% style="width:282px" %)Communication control|(% style="width:452px" %)For communication control and communication lamp (please refer to "[[communication control>>http://13.229.109.52:8080/wiki/pistudio/view/Helps/13.HMI%20internal%20registers/#HCommunicationcontrol]]" sector for detailed)

293

|=(% style="width: 160px;" %)HSW850|(% style="width:282px" %)(((

294

Network state

295

296

(4G, WIFI and Ethernet)

297

)))|(% style="width:452px" %)(((

298

In HMI V1.0

299

300

* =0: Network is disconnected.

301

* =1: only LAN connected, and APP can't access HMI.

302

* =2: WECON Cloud connected , APP and web could access HMI.

In HMI V2.0

* =0: Network is disconnected.

307

* =1: Network is connected.

308

)))

309

|=(% style="width: 160px;" %)HSW855|(% style="width:282px" %)Backlight Control|(% style="width:452px" %)(((

310

* HSX855.0=1: turn on the backlight and reset automatically after being triggered.

311

* HSX855.1=1: turn off the backlight and reset automatically after being triggered.

312

)))

313

|=(% style="width: 160px;" %)HSW856|(% style="width:282px" %)Whether to close the indirect screen when the current screen is switched to the other screen)|(% style="width:452px" %)(((

314

* =0: close the sub-screen, including the indirect screen;

315

* =1: not to close.

316

)))

317

|=(% style="width: 160px;" %)HSW857|(% style="width:282px" %)Permission in remote access (web page, mobile APP, cloud platform, etc.)|(% style="width:452px" %)(((

318

* =0: users could switch the screen, control the switch and update data in remote access.

319

* =1: users could only control function switch (only switch the screen), view data and switch state, but could not operate or update them.

320

* =2: users could neither operate the screen switch, nor switch operation and data modification, only view.( ig series)

321

)))

322

|=(% style="width: 160px;" %)HSW881|(% style="width:282px" %)Storage of Record files|(% style="width:452px" %)(((

323

It is used for controlling saving alarm/data record files to U disk / SD card.

324

325

* = 0: Save to storage.

326

* = 1: Don't save to storage.

327

)))

328

|=(% style="width: 160px;" %)HSW882|(% style="width:282px" %)Storage device status|(% style="width:452px" %)(((

329

* HDX882.0=0 USB flash doesn't execute storage or storage finished.

330

* HDX882.0=1 USB flash is reading data, don't remove USB flash.

331

* HDX882.1=0 SD card doesn't execute storage or storage finished.

332

* HDX882.1=1 SD card is reading data, don't remove SD card.

333

)))

334

|=(% style="width: 160px;" %)HSW884|(% style="width:282px" %)Enter setup screen|(% style="width:452px" %)(((

335

* = 0: Do not into setup screen

336

* = 1: Enter setup screen

337

)))

338

|=(% style="width: 160px;" %)HSW885|(% style="width:282px" %)When the control object hides the address is read failed (communication failure), set the display mode of the object|(% style="width:452px" %)(((

339

* = 0: displayed by object setting.

340

* =1: control address read failure, the address control of all objects is hidden, not displayed.

341

* =2: control address read failure, the address control of all objects is displayed, not hidden.

342

)))

343

|=(% style="width: 160px;" %)HSW893|(% style="width:282px" %)(((

344

User Permission Control Address, same as HUW1000 feature, please refer to chapter "[[User Permission>>http://13.229.109.52:8080/wiki/pistudio/view/Helps/08.Basic%20Function/#HUserPermission]]"

345

346

**✎Note: **This address can only take effect when it is operated in the real HMI, and the operation is invalid on Web/App side.

347

)))|(% style="width:452px" %)(((

348

* =1: User Log in

349

* =2: Change User password

* =3: User Log out

* =4: New user

* =5: Delete user

* =6: Add user rights

354

* =8: Add Hide features

355

* =9: Delete Profile

356

* =10: Export Profile

357

* =11: Import profile

358

* =12: Export log file

359

* =13: Delete log file

360

)))

361

|=(% style="width: 160px;" %)HSW900|(% style="width:282px" %)Quick update frequency settings for objects|(% style="width:452px" %)(((

362

Valid when the object is enabled for "quick update". Default: 5.

363

364

Range: 1 (fastest) ~~ 50 (slowest)

365

)))

366

|=(% style="width: 160px;" %)HSW920|(% style="width:282px" %)Static mode Maximum periods|(% style="width:452px" %)Numeric Input/ Display (range: 0-12)

367

|=(% style="width: 160px;" %)HSW921 ~~ 924|(% style="width:282px" %)Static mode Admin key|(% style="width:452px" %)Character Input/ Display (length: 8)

368

|=(% style="width: 160px;" %)HSW925 ~~ 928|(% style="width:282px" %)1^^st^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

369

|=(% style="width: 160px;" %)HSW929 ~~ 933|(% style="width:282px" %)1^^st^^ expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

370

|=(% style="width: 160px;" %)HSW935 ~~ 938|(% style="width:282px" %)2^^nd^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

371

|=(% style="width: 160px;" %)HSW939 ~~ 943|(% style="width:282px" %)2^^nd ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

372

|=(% style="width: 160px;" %)HSW945 ~~ 948|(% style="width:282px" %)3^^rd^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

373

|=(% style="width: 160px;" %)HSW949 ~~ 953|(% style="width:282px" %)3^^rd ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

374

|=(% style="width: 160px;" %)HSW955 ~~ 958|(% style="width:282px" %)4^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

375

|=(% style="width: 160px;" %)HSW959 ~~ 963|(% style="width:282px" %)4^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

376

|=(% style="width: 160px;" %)HSW965 ~~ 968|(% style="width:282px" %)5^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

377

|=(% style="width: 160px;" %)HSW969 ~~ 973|(% style="width:282px" %)5^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

378

|=(% style="width: 160px;" %)HSW975 ~~ 978|(% style="width:282px" %)6^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

379

|=(% style="width: 160px;" %)HSW979 ~~ 983|(% style="width:282px" %)6^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

380

|=(% style="width: 160px;" %)HSW985 ~~ 988|(% style="width:282px" %)7^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

381

|=(% style="width: 160px;" %)HSW989 ~~ 993|(% style="width:282px" %)7^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

382

|=(% style="width: 160px;" %)HSW995 ~~ 998|(% style="width:282px" %)8^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

383

|=(% style="width: 160px;" %)HSW999 ~~ 1003|(% style="width:282px" %)8^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

384

|=(% style="width: 160px;" %)HSW1005 ~~1008|(% style="width:282px" %)9^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

385

|=(% style="width: 160px;" %)HSW1009 ~~ 1013|(% style="width:282px" %)9^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

386

|=(% style="width: 160px;" %)HSW1015 ~~1018|(% style="width:282px" %)10^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

387

|=(% style="width: 160px;" %)HSW1019 ~~ 1023|(% style="width:282px" %)10^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

388

|=(% style="width: 160px;" %)HSW1025 ~~1028|(% style="width:282px" %)11^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

389

|=(% style="width: 160px;" %)HSW1029 ~~ 1033|(% style="width:282px" %)11^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

390

|=(% style="width: 160px;" %)HSW1035 ~~1038|(% style="width:282px" %)12^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)

391

|=(% style="width: 160px;" %)HSW1039 ~~ 1043|(% style="width:282px" %)12^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)

392

|=(% style="width: 160px;" %)HSW1046|(% style="width:282px" %)Current period (Static mode)|(% style="width:452px" %)Current period (Range 1-13)

393

|=(% style="width: 160px;" %)HSW1047|(% style="width:282px" %)Save settings (Static mode)|(% style="width:452px" %)(((

394

* HSX1047.0=1: Save static installment information

395

* HSX1047.1=1: Write installment information to registers

396

)))

397

|=(% style="width: 160px;" %)HSW1050~~HSW1065|(% style="width:282px" %)The recipe name that can input csv format|(% style="width:452px" %)Input CSV format recipe file name through "Character Input/ Display".(This function should be used in combination with the recipefunction)

398

|=(% style="width: 160px;" %)HSW1066|(% style="width:282px" %)Configure the type of the CSV file imported|(% style="width:452px" %)(((

399

The CSV file type imported (This function should be used in combination with the recipe function)

400

401

* =0: Import customed CSV file. The data in the file is valid.

402

* =1: Import ordinary recipe files of regular series HMI. The 1st row of the file is invalid.

403

* =2: Import special recipe files of regular series HMI. The 1st and 3nd rows and the 1st colume of the file is invalid.

404

)))

405

|=(% style="width: 160px;" %)HSW1067|(% style="width:282px" %)Location where the CSV file is saved|(% style="width:452px" %)(((

406

Set the path of CSV file (This function should be used in combination with the recipe function)

407

408

* =0: In the CsvFile directory of the USB stick

409

* =1: In the CsvFile directory of the SD card

410

)))

411

|=(% style="width: 160px;" %)HSW1070|(% style="width:282px" %)The time interval (seconds) since the last time the screen was clicked|(% style="width:452px" %)(((

412

Shows how long the current screen has not been clicked, using a decimal unsigned double word (Numeric Input/ Display).

413

414

**✎Note: **This register is cleared to zero regardless of which user clicks on the screen.

415

)))

416

|=(% style="width: 160px;" %)HSW1073|(% style="width:282px" %)Corresponding key value from keyboard|(% style="width:452px" %)Display the key value of the currently pressed key, the key value is shown in Table 1 (not updated when the character input display is being input)

417

|=(% style="width: 160px;" %)HSW1074|(% style="width:282px" %)Keyboard key status|(% style="width:452px" %)Display the current button status (not updated when the numeric input display is being input)(((

418

* =0: key release

419

* =1: key press

420

* =2: Long press the button

421

)))

422

|=(% style="width: 160px;" %)HSW1075|(% style="width:282px" %)Cursor speed|(% style="width:452px" %)Control the cursor movement speed, the range is 0～100, the default is 20

423

|=(% style="width: 160px;" %)HSW1076|(% style="width:282px" %)Cursor x coordinate value|(% style="width:452px" %)Record the x value at the current position of the cursor, range: 0 to screen width -1

424

|=(% style="width: 160px;" %)HSW1077|(% style="width:282px" %)Cursor y coordinate value|(% style="width:452px" %)Record the y value at the current position of the cursor, range: 0 to screen height-1

425

|=(% style="width: 160px;" %)HSW1078|(% style="width:282px" %)Corresponding ASCII code for keyboard keys|(% style="width:452px" %)Only the ASCII value of letters, numbers, and symbols are displayed, and the ASCII value of the function button is not displayed.

426

|=(% style="width: 160px;" %)HSW1079|(% style="width:282px" %)Trigger to set the cursor position and set the Enter key mode|(% style="width:452px" %)(((

427

* HSX1079.0=1: Set the cursor position according to the cursor xy register value;

428

* HSX1079.1=0: When the numeric/character input display is being input, press Enter to end the input, no value/text part is being input, Enter is a normal click;

429

* HSX1079.1=1 Regardless of whether the numeric/character component is inputting the Enter key, only normal click is performed, and the keyboard end input is not performed.

430

)))

431

|=(% style="width: 160px;" %)HSW1083|(% style="width:282px" %)Naming method for printing object screenshots|(% style="width:452px" %)(((

432

Example: The time is 2019-01-04 14:29:10 (523 milliseconds), the screen number is 0, and the object ID is 2.

433

434

* =0: Use year, month, day, hour, minute, second, millisecond, screen number, part number to name, such as: 2019010414291052302.bmp.

435

* =1: Name using year, month, day, hour, minute, and second.

436

437

For example: 20190104142910.bmp.

438

)))

439

|=(% style="width: 160px;" %)HSW1086|(% style="width:282px" %)Control address mapping polling cycle, unit: ms|(% style="width:452px" %)(((

440

Address mapping polling cycle, effective range: 40~~1000ms, default: 300ms.

441

442

* When the set value is greater than 1000, the value is 1000.

443

* When the set value is greater than 1000, it changes to the default value 300

444

)))

445

|=(% style="width: 160px;" %)HSW1087|(% style="width:282px" %)Control write interval in address mapping|(% style="width:452px" %)(((

446

After reading data to the device for N times, Perform an address mapping write operation. N is the interval value. The effective range: 0~~5, and default is 2.

447

448

When N more than 5, it is 5.

449

450

0 is the fastest and 5 is the slowest.

451

)))

452

|=(% style="width: 160px;" %)HSW1088|(% style="width:282px" %)Control the write interval of script|(% style="width:452px" %)(((

453

After reading data to the device for N times, Perform a script write operation. N is the interval value. The effective range: 0~~5, and default is 2.

454

455

When N more than 5, it is 5.

456

457

0 is the fastest and 5 is the slowest.

458

)))

459

|=(% style="width: 160px;" %)HSW1089|(% style="width:282px" %)Control interval of read through|(% style="width:452px" %)(((

460

After reading data to the device for N times, Perform a read through operation. N is the interval value. The effective range: 0~~5, and default is 2.

461

462

When N more than 5, it is 5.

463

464

0 is the fastest and 5 is the slowest.

465

)))

466

|=(% style="width: 160px;" %)HSW1100|(% colspan="1" rowspan="4" style="width:282px" %)Set the Master IP for Multi-link|(% style="width:452px" %)High word 1 for Master IP address of multi-link

467

|=(% style="width: 160px;" %)HSW1101|(% style="width:452px" %)High word 2 for Master IP address of multi-link

468

|=(% style="width: 160px;" %)HSW1102|(% style="width:452px" %)High word 3 for Master IP address of multi-link

469

|=(% style="width: 160px;" %)HSW1103|(% style="width:452px" %)High word 4 for Master IP address of multi-link

470

|=(% style="width: 160px;" %)HSW1104|(% style="width:282px" %)Control connection to Master or not for Multi-link slave device|(% style="width:452px" %)(((

471

* =1: Connect to the Master

472

* =0: Do not connect to Master

473

)))

474

|=(% style="width: 160px;" %)HSW1141|(% style="width:282px" %)Release alarm|(% style="width:452px" %)(((

475

* =0, Default value

476

* =1, Release the alarm generated before the last power-down when starting up

477

)))

478

|=(% style="width: 160px;" %)HSW1450|(% style="width:282px" %)Enable objects level password function|(% style="width:452px" %)(((

* =0, Disable

* =1, Enable

)))

|=(% style="width: 160px;" %)HSW1451|(% style="width:282px" %)Whether the object level passwords are independent of each other|(% style="width:452px" %)(((

483

* =0, No, high-level passwords can unlock low-level

484

* = 1, Yes, high-level passwords cannot unlock low-level

485

)))

486

|=(% style="width: 160px;" %)HSW1452|(% style="width:282px" %)Initialization level|(% style="width:452px" %)Initialization level while HMI running

487

|=(% style="width: 160px;" %)HSW1454~~1457|(% style="width:282px" %)Password for Level 1|(% style="width:452px" %)(((

488

Display password for level 1, using character input object, up to 8 characters (numbers, letters (case sensitive))

489

)))

490

|=(% style="width: 160px;" %)HSW1458~~1461|(% style="width:282px" %)Password for Level 2|(% style="width:452px" %)Display password for level 2, using character input object, up to 8 characters (numbers, letters (case sensitive))

491

|=(% style="width: 160px;" %)HSW1462~~1465|(% style="width:282px" %)Password for Level 3|(% style="width:452px" %)Display password for level 3, using character input object, up to 8 characters (numbers, letters (case sensitive))

492

|=(% style="width: 160px;" %)HSW1466~~1469|(% style="width:282px" %)Password for Level 4|(% style="width:452px" %)Display password for level 4, using character input object, up to 8 characters (numbers, letters (case sensitive))

493

|=(% style="width: 160px;" %)HSW1470~~1473|(% style="width:282px" %)Password for Level 5|(% style="width:452px" %)Display password for level 5, using character input object, up to 8 characters (numbers, letters (case sensitive))

494

|=(% style="width: 160px;" %)HSW1474~~1477|(% style="width:282px" %)Password for Level 6|(% style="width:452px" %)Display password for level 6, using character input object, up to 8 characters (numbers, letters (case sensitive))

495

|=(% style="width: 160px;" %)HSW1478~~1481|(% style="width:282px" %)Password for Level 7|(% style="width:452px" %)Display password for level 7, using character input object, up to 8 characters (numbers, letters (case sensitive))

496

|=(% style="width: 160px;" %)HSW1482~~1485|(% style="width:282px" %)Password for Level 8|(% style="width:452px" %)Display password for level 8, using character input object, up to 8 characters (numbers, letters (case sensitive))

497

|=(% style="width: 160px;" %)HSW1486~~1489|(% style="width:282px" %)Password for Level 9|(% style="width:452px" %)Display password for level 9, using character input object, up to 8 characters (numbers, letters (case sensitive))

498

|=(% style="width: 160px;" %)HSW1490~~1493|(% style="width:282px" %)Password for Level 10|(% style="width:452px" %)Display password for level 10, using character input object, up to 8 characters (numbers, letters (case sensitive))

499

|=(% style="width: 160px;" %)HSW1494~~1497|(% style="width:282px" %)Password for Level 11|(% style="width:452px" %)Display password for level 11, using character input object, up to 8 characters (numbers, letters (case sensitive))

500

|=(% style="width: 160px;" %)HSW1498~~1501|(% style="width:282px" %)Password for Level 12|(% style="width:452px" %)Display password for level 12, using character input object, up to 8 characters (numbers, letters (case sensitive))

501

|=(% style="width: 160px;" %)HSW1502|(% style="width:282px" %)Modify password for object level|(% style="width:452px" %)(((

502

* HSX1502.0=1: Modification comfirmed. Save the data of HSW1450~~HSW1501 to a file for immediate effect.

503

* HSX1502.1=1:Modification cancelled. Restore the current data of hSW1450-HSW1501 to the data saved in the file last time.

504

)))

505

|=(% style="width: 160px;" %)HSW1603|(% style="width:282px" %)Number of current unreleased alarms|(% style="width:452px" %)The number of current unreleased alarms in alarm record file.

506

|=(% style="width: 160px;" %)HSW1604|(% style="width:282px" %)The auxiliary judgment address when the control bit in the Object Lock fails to be read|(% style="width:452px" %)(((

507

* =0: The auxiliary address is invalid.

508

* =1: When the communication fails, lock the object.

509

* =2: When the communication fails, unlock the object.

510

* =Others: The auxiliary address is invalid.

511

)))

512

|=(% style="width: 160px;" %)HSW1605|(% style="width:282px" %)BCD format natural decimal control|(% style="width:452px" %)(((

513

Whether to display natural decimals with decimal point in BCD format:

* 0=Not enabled.

* 1=Enable.

(For example, 56.20 is displayed as 56.2, 33.00 is displayed as 33)

519

)))

520

|=(% style="width: 160px;" %)HSW1606|(% style="width:282px" %)User permission modification control|(% style="width:452px" %)(((

521

* =0: Ordinary users are allowed to modify permissions and other operations

522

* =1: Only the administrator can operate (default is 0)

523

)))

524

|=(% style="width: 160px;" %)HSW1607|(% style="width:282px" %)The spacing value among the drop-down items of the drop-down list|(% style="width:452px" %)10 to 50 is effective, such as: 23 is 2.3 times the height of the object.

525

|=(% style="width: 160px;" %)HSW1611|(% style="width:282px" %)(((

526

Traditional recipe transfer

527

)))|(% style="width:452px" %)(((

528

* =1: download traditional recipe.

529

* =2: upload the traditional recipe.

530

)))

531

|=(% style="width: 160px;" %)HSW1612|(% style="width:282px" %)Traditional Recipe group number|(% style="width:452px" %)Traditional Recipe group number

532

|=(% style="width: 160px;" %)HSW1613|(% style="width:282px" %)Display the status of network card|(% style="width:452px" %)(((

* =1: Normal

* =Others: Abnormal

)))

|=(% style="width: 160px;" %)HSW1614~~1623|(% style="width:282px" %)Download speed per second|(% style="width:452px" %)Display the download speed per second. (The value is string)

537

|=(% style="width: 160px;" %)HSW1624~~1633|(% style="width:282px" %)Upnload speed per second|(% style="width:452px" %)Display the upload speed per second. (The value is string)

538

|=(% style="width: 160px;" %)HSW1634~~1643|(% style="width:282px" %)Flow consumption rate|(% style="width:452px" %)Display the total flow rate per second (The value is string)

539

|=(% style="width: 160px;" %)HSW1644~~1653|(% style="width:282px" %)Download flow consumption after power on|(% style="width:452px" %)Display the download flow consumption after power on (The value is string)

540

|=(% style="width: 160px;" %)HSW1654~~1663|(% style="width:282px" %)Upload flow consumption after power on|(% style="width:452px" %)Display the upload flow consumption after power on (The value is string)

541

|=(% style="width: 160px;" %)HSW1664~~1673|(% style="width:282px" %)Total flow consumption after power on|(% style="width:452px" %)Display the total flow consumption after power on (download and upload). (The value is string)

542

|=(% style="width: 160px;" %)HSW1674~~1683|(% style="width:282px" %)Historical flow consumption|(% style="width:452px" %)Display historical flow consumption (download and upload). (The value is string)

543

|=(% style="width: 160px;" %)HSW1684~~1693|(% style="width:282px" %)Flow consumption in 10 minutes|(% style="width:452px" %)Flow consumption in 10 minutes (download and upload). (The value is string)

544

|=(% style="width: 160px;" %)HSW1694~~1703|(% style="width:282px" %)Flow consumption in 30 minutes|(% style="width:452px" %)Flow consumption in 30 minutes (download and upload). (The value is string)

545

|=(% style="width: 160px;" %)HSW1704~~1713|(% style="width:282px" %)Flow consumption in 3 hours|(% style="width:452px" %)Flow consumption in 3 hours (download and upload). (The value is string)

546

|=(% style="width: 160px;" %)HSW1715|(% style="width:282px" %)Reset flow|(% style="width:452px" %)(((

547

* =1: Clear historical flow data and restart the count.

548

* =Others: Invalid

549

)))

550

|=(% style="width: 160px;" %)HSW1719|(% style="width:282px" %)Network status of Ethernet connnecting to server|(% style="width:452px" %)(((

551

* =0: Server connection exception

552

* =1: Server connection is OK

553

)))

554

|=(% style="width: 160px;" %)HSW1720|(% colspan="1" rowspan="12" style="width:282px" %)Related IP register in WIFI network status (It is valid when HMI is connected to WIFI)|(% style="width:452px" %)Local IP address high byte 1

555

|=(% style="width: 160px;" %)HSW1721|(% style="width:452px" %)Local IP address high byte 2

556

|=(% style="width: 160px;" %)HSW1722|(% style="width:452px" %)Local IP address high byte 3

557

|=(% style="width: 160px;" %)HSW1723|(% style="width:452px" %)Local IP address high byte 4

558

|=(% style="width: 160px;" %)HSW1724|(% style="width:452px" %)Local mask IP address high byte 1

559

|=(% style="width: 160px;" %)HSW1725|(% style="width:452px" %)Local mask IP address high byte 2

560

|=(% style="width: 160px;" %)HSW1726|(% style="width:452px" %)Local mask IP address high byte 3

561

|=(% style="width: 160px;" %)HSW1727|(% style="width:452px" %)Local mask IP address high byte 4

562

|=(% style="width: 160px;" %)HSW1728|(% style="width:452px" %)Local gateway IP address high byte 1

563

|=(% style="width: 160px;" %)HSW1729|(% style="width:452px" %)Local gateway IP address high byte 2

564

|=(% style="width: 160px;" %)HSW1730|(% style="width:452px" %)Local gateway IP address high byte 3

565

|=(% style="width: 160px;" %)HSW1731|(% style="width:452px" %)Local gateway IP address high byte 4

566

|=(% style="width: 160px;" %)HSW1733|(% colspan="1" rowspan="6" style="width:282px" %)(((

567

Display the MAC code of current WIFI

568

569

(display in hexadecimal)

570

)))|(% style="width:452px" %)Local MAC address high byte 1 (hexadecimal)

571

|=(% style="width: 160px;" %)HSW1734|(% style="width:452px" %)Local MAC address high byte 2 (hexadecimal)

572

|=(% style="width: 160px;" %)HSW1735|(% style="width:452px" %)Local MAC address high byte 3 (hexadecimal)

573

|=(% style="width: 160px;" %)HSW1736|(% style="width:452px" %)Local MAC address high byte 4 (hexadecimal)

574

|=(% style="width: 160px;" %)HSW1737|(% style="width:452px" %)Local MAC address high byte 5 (hexadecimal)

575

|=(% style="width: 160px;" %)HSW1738|(% style="width:452px" %)Local MAC address high byte 6 (hexadecimal)

576

|=(% style="width: 160px;" %)HSW1739|(% style="width:282px" %)Display the network status of WIFI|(% style="width:452px" %)(((

577

* =0: Server connection exception

578

* =1: Server connection is OK

579

)))

580

|=(% style="width: 160px;" %)HSW1741|(% colspan="1" rowspan="12" style="width:282px" %)Related IP register in 4Gnetwork status (It is valid when HMI is connected to 4G)|(% style="width:452px" %)Local IP address high byte 1

581

|=(% style="width: 160px;" %)HSW1742|(% style="width:452px" %)Local IP address high byte 2

582

|=(% style="width: 160px;" %)HSW1743|(% style="width:452px" %)Local IP address high byte 3

583

|=(% style="width: 160px;" %)HSW1744|(% style="width:452px" %)Local IP address high byte 4

584

|=(% style="width: 160px;" %)HSW1745|(% style="width:452px" %)Local mask IP address high byte 1

585

|=(% style="width: 160px;" %)HSW1746|(% style="width:452px" %)Local mask IP address high byte 2

586

|=(% style="width: 160px;" %)HSW1747|(% style="width:452px" %)Local mask IP address high byte 3

587

|=(% style="width: 160px;" %)HSW1748|(% style="width:452px" %)Local mask IP address high byte 4

588

|=(% style="width: 160px;" %)HSW1749|(% style="width:452px" %)Local gateway IP address high byte 1

589

|=(% style="width: 160px;" %)HSW1750|(% style="width:452px" %)Local gateway IP address high byte 2

590

|=(% style="width: 160px;" %)HSW1751|(% style="width:452px" %)Local gateway IP address high byte 3

591

|=(% style="width: 160px;" %)HSW1752|(% style="width:452px" %)Local gateway IP address high byte 4

592

|=(% style="width: 160px;" %)HSW1754|(% colspan="1" rowspan="6" style="width:282px" %)(((

593

Display the MAC code of current WIFI

594

595

(display in hexadecimal)

596

)))|(% style="width:452px" %)Local MAC address high byte 1 (hexadecimal)

597

|=(% style="width: 160px;" %)HSW1755|(% style="width:452px" %)Local MAC address high byte 2 (hexadecimal)

598

|=(% style="width: 160px;" %)HSW1756|(% style="width:452px" %)Local MAC address high byte 3 (hexadecimal)

599

|=(% style="width: 160px;" %)HSW1757|(% style="width:452px" %)Local MAC address high byte 4 (hexadecimal)

600

|=(% style="width: 160px;" %)HSW1758|(% style="width:452px" %)Local MAC address high byte 5 (hexadecimal)

601

|=(% style="width: 160px;" %)HSW1759|(% style="width:452px" %)Local MAC address high byte 6 (hexadecimal)

602

|=(% style="width: 160px;" %)HSW1760|(% style="width:282px" %)Display 4G network status|(% style="width:452px" %)(((

603

* =0: Server connection exception

604

* =1: Server connection is OK

605

)))

606

|=(% style="width: 160px;" %)HSW1761|(% style="width:282px" %)Display 4G network signal strength|(% style="width:452px" %)Signal strength: 0~~31. The greater the value ,the signal is stronger

607

|=(% style="width: 160px;" %)HSW1852|(% style="width:282px" %)Control the interval in two consecutive clicks|(% style="width:452px" %)Limit range: 1~~500ms. The default is 100 ms.

608

|=(% style="width: 160px;" %)HSW1853|(% style="width:282px" %)File format for exporting data records to USB flash drive or SD card|(% style="width:452px" %)(((

* =0: db database

* =1: CSV

)))

|=(% style="width: 160px;" %)HSW1854|(% style="width:282px" %)High and low word conversion type|(% style="width:452px" %)(((

613

* =0: use the old high-low word conversion (default)

614

* =1: usie the new high-low word conversion

615

)))

616

|=(% style="width: 160px;" %)HSW1855|(% style="width:282px" %)Screen Lock prompt display control|(% style="width:452px" %)(((

617

Control whether the screen lock prompt is displayed,

618

619

* =0: display(default value)

620

* =Other: no display.

621

)))

622

|=(% style="width: 160px;" %)HSW1856|(% style="width:282px" %)Display map fence drawing status|(% style="width:452px" %)(((

623

* =0: no map fence

624

* =1: The map fence is drawn and the device is inside the fence

625

* =2: The map fence is drawn and the device is outside the fence

626

)))

627

|=(% style="width: 160px;" %)HSW1857|(% style="width:282px" %)USB disk download |(% style="width:452px" %)(((

628

* =0: download project

629

* =1: download firmware

630

* =2: enter the background

631

)))

632

|=(% style="width: 160px;" %)HSW10000~~19999|(% style="width:282px" %)Power-down storage area|(% style="width:452px" %)After restart, the data remains

633

|=(% style="width: 160px;" %)HSW10035|(% rowspan="13" style="width:282px" %)(((

634

**✎Note: **Only valid when the HMI is plugged into the Ethernet cable.

635

636

1. If Ethernet settings is enabled in project parameters, this register displays the set value.

637

1. If Ethernet settings is not enabled in project parameters, IP would automatically obtained IP.

638

1. If HMI is not connected to the network, the register is displayed as 0 whether the engineering parameters are set.

639

1. 4. All IP registers of HMI are read-only.

640

)))|(% style="width:452px" %)Local IP address high byte 1

641

|=(% style="width: 160px;" %)HSW10036|(% style="width:452px" %)Local IP address high byte 2

642

|=(% style="width: 160px;" %)HSW10037|(% style="width:452px" %)Local IP address high byte 3

643

|=(% style="width: 160px;" %)HSW10038|(% style="width:452px" %)Local IP address high byte 4

644

|=(% style="width: 160px;" %)HSW10039|(% style="width:452px" %)Local mask IP address high byte 1

645

|=(% style="width: 160px;" %)HSW10040|(% style="width:452px" %)Local mask IP address high byte 2

646

|=(% style="width: 160px;" %)HSW10041|(% style="width:452px" %)Local mask IP address high byte 3

647

|=(% style="width: 160px;" %)HSW10042|(% style="width:452px" %)Local mask IP address high byte 4

648

|=(% style="width: 160px;" %)HSW10043|(% style="width:452px" %)Local gateway address high byte 1

649

|=(% style="width: 160px;" %)HSW10044|(% style="width:452px" %)Local gateway address high byte 2

650

|=(% style="width: 160px;" %)HSW10045|(% style="width:452px" %)Local gateway address high byte 3

651

|=(% style="width: 160px;" %)HSW10046|(% style="width:452px" %)Local gateway address high byte 4

652

|=(% style="width: 160px;" %)HSW10047|(% style="width:452px" %)Local port address

653

|=(% style="width: 160px;" %)HSW10048|(% rowspan="6" style="width:282px" %)(((

654

Displays the MAC code of the current network card

655

656

(Hexadecimal display)

657

)))|(% style="width:452px" %)Local MAC code high word 1

658

|=(% style="width: 160px;" %)HSW10049|(% style="width:452px" %)Local MAC code high word 2

659

|=(% style="width: 160px;" %)HSW10050|(% style="width:452px" %)Local MAC code high word 3

660

|=(% style="width: 160px;" %)HSW10051|(% style="width:452px" %)Local MAC code high word 4

661

|=(% style="width: 160px;" %)HSW10052|(% style="width:452px" %)Local MAC code high word 5

662

|=(% style="width: 160px;" %)HSW10053|(% style="width:452px" %)Local MAC code high word 6

663

|=(% style="width: 160px;" %)HSW10118|(% colspan="1" rowspan="2" style="width:282px" %)TSAP settings for HMI in the Siemens logo! 8 protocol|(% style="width:452px" %)HMI local TSAP, which corresponds to the remote TSAP of PLC

664

|=(% style="width: 160px;" %)HSW10119|(% style="width:452px" %)HMI remote TSAP, which corresponds to the local TSAP of PLC

665

|=(% style="width: 160px;" %)HSW10461~~10493|(% style="width:282px" %)Remote access password|(% style="width:452px" %)8-character remote access password

666

|=(% style="width: 160px;" %)HSW10494~~10558|(% style="width:282px" %)Machine ID (Read only)|(% style="width:452px" %)Machine ID for remote access (read only 64-bit)

667

|=(% style="width: 160px;" %)HSW10576|(% style="width:282px" %)Save dynamic installment settings|(% style="width:452px" %)HSX10576.0=1: Save the set dynamic installment information

668

|=(% style="width: 160px;" %)HSW10577|(% style="width:282px" %)Control address for installment|(% style="width:452px" %)(((

669

* HSX10577.0=0: disable dynamic installment

670

* HSX10577.0=1: enable dynamic installment

671

* HSX10577.1=0: disable static installment

672

* HSX10577.1=1: enable static installment

673

)))

674

|=(% style="width: 160px;" %)HSW10578-10583|(% style="width:282px" %)Password for dynamic installment|(% style="width:452px" %)Character Input/ Display (length: 6)

675

|=(% style="width: 160px;" %)HSW10584-10586|(% style="width:282px" %)Expiry time of dynamic installment|(% style="width:452px" %)Expiry time: YYYYMMDD (Numeric Input/ Display)

676

|=(% style="width: 160px;" %)HSW10587-10589|(% style="width:282px" %)Last expiry time of dynamic installment|(% style="width:452px" %)Expiry time: YYYYMMDD (Numeric Input/ Display)

677

|=(% style="width: 160px;" %)HSW10590|(% style="width:282px" %)Background light time|(% style="width:452px" %)(((

678

Set the light time for background

679

680

* =0: The screen backlight is always on.

681

* =Others: The screen backlight is on for a period of time and then turns off. The length of time is controlled by the value of the register address. Unit: second.

682

)))

683

|=(% style="width: 160px;" %)HSW10591|(% style="width:282px" %)Backlight brightness adjustment|(% style="width:452px" %)Backlight brightness range: 1 (darkest) ~~ 100 (brightest)

684

|=(% style="width: 160px;" %)HSW10603|(% style="width:282px" %)Set the printer to print orientation|(% style="width:452px" %)(((

685

Set the print direction:

686

687

* =1: Forward printing

688

* =2: Reverse print

689

* =Other: Forward print

690

)))

691

|=(% style="width: 160px;" %)HSW10604|(% style="width:282px" %)Print dot type|(% style="width:452px" %)(((

692

* =1: new firmware 8 dot matrix type

693

* =2: new firmware 24 dot matrix type

694

* =3: old firmware 8 dot matrix type

695

* =4: old firmware 24 dot matrix type

696

* =Other: new firmware 8 dot matrix type

697

)))

698

|=(% style="width: 160px;" %)HSW10605|(% style="width:282px" %)Print width of printer|(% style="width:452px" %)Set the width of the printer to print (in pixels), such as HSW10605 = 394: The printer supports images with a print width of 394 pixels

699

|=(% style="width: 160px;" %)HSW10606|(% style="width:282px" %)Printer instruction type|(% style="width:452px" %)(((

700

* =1: Graphic print type

701

* =2: Dot density printing type

702

* =3: special for EPSON printer

703

)))

704

|=(% style="width: 160px;" %)HSW10607|(% style="width:282px" %)Printer paper cutting function|(% style="width:452px" %)(((

* =1: Enable

* =2: Disable

)))

|=(% style="width: 160px;" %)HSW10608|(% style="width:282px" %)Print the alignment of the text|(% style="width:452px" %)(((

709

* =1: Left alignment

710

* =2: Center alignment

711

* =3: Right alignment

712

)))

713

|=(% style="width: 160px;" %)HSW10610|(% style="width:282px" %)Set weconcloud server|(% style="width:452px" %)(((

714

* =0: Select the server configured in "Project Settings"

715

* =1: select Server 1

716

* =2: select Server 2

717

)))

718

|=(% style="width: 160px;" %)HSW11750|(% style="width:282px" %)Set the language of the Message List prompt** (ie series)**|(% style="width:452px" %)(((

719

* =0: which is followed the project language

* =1: English

* =2: Chinese

)))

|=(% style="width: 160px;" %)HSW11756|(% style="width:282px" %)(((

724

Set access permission restrictions

725

726

**(ig series)**

727

)))|(% style="width:452px" %)(((

728

* =0: LAN or the external network both OK

729

* =1: Only LAN access

730

* =2: Only external network can access

731

)))

732

|=(% style="width: 160px;" %)HSW11757|(% style="width:282px" %)Enable the valid date of the dynamic installment password|(% style="width:452px" %)(((

* =0: Disabled

* =1: Enable

)))

|=(% style="width: 160px;" %)HSW11758|(% style="width:282px" %)Enable Screensaver|(% style="width:452px" %)(((

* =0: Disabled

* =1: Enable

)))

|=(% style="width: 160px;" %)HSW11759|(% style="width:282px" %)Screensaver interval time|(% style="width:452px" %)(((

741

Set the time how long will enter Screensaver (Range 10~~43200s)

742

)))

743

|=(% style="width: 160px;" %)HSW11760|(% style="width:282px" %)Screensaver countdown|(% style="width:452px" %)Display the countdown to enter the Screensaver, unit: second.

744

|=(% style="width: 160px;" %)HSW11761|(% style="width:282px" %)Screensaver screen number|(% style="width:452px" %)Set the screen number for Screensaver

745

746

== **Serial port communication configuration** ==

747

748

(% class="table-bordered" %)

749

|=(% style="width: 102px;" %)Port|=(% style="width: 173px;" %)**Function**|=(% style="width: 122px;" %)**Address**|=(% colspan="2" style="width: 506px;" %)**Description**

750

|(% colspan="1" rowspan="11" style="width:102px" %)COM1|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10061|(% colspan="2" style="width:506px" %)(((

* =0: RS232

* =1: RS485

* =2: RS422

)))

|(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10062|(% colspan="2" style="width:506px" %)(((

* =0: 1200

* =1: 2400

* =2: 4800

* =3: 9600

* =4: 19200

* =5: 38400

* =6: 57600

* =7: 115200

* =8: 230400

)))

|(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10063|(% colspan="2" style="width:506px" %)(((

* =7: 7 bit

* =8: 8 bit

)))

|(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10064|(% colspan="2" style="width:506px" %)(((

* =1: 1 bit

* =2: 2 bit

)))

|(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10065|(% colspan="2" style="width:506px" %)(((

* =0: None

* =1: ODD

* =2: EVEN

)))

|(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10066|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

780

|(% style="width:173px" %)reveive timeout|(% style="width:122px" %)HSW10067|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

781

|(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10068|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100

782

|(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10069|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~300

783

|(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10070|(% colspan="2" style="width:506px" %)

784

|(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10071|(% colspan="2" style="width:506px" %)

785

|(% colspan="1" rowspan="11" style="width:102px" %)COM1-2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10094|(% colspan="2" style="width:506px" %)(((

* =0: RS232

* =1: RS485

* =2: RS422

* =6: RS485-2

)))

|(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10095|(% colspan="2" style="width:506px" %)(((

* =0: 1200

* =1: 2400

* =2: 4800

* =3: 9600

* =4: 19200

* =5: 38400

* =6: 57600

* =7: 115200

* =8: 230400

)))

|(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10096|(% colspan="2" style="width:506px" %)(((

* =7: 7 bit

* =8: 8 bit

)))

|(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10097|(% colspan="2" style="width:506px" %)(((

* =1: 1 bit

* =2: 2 bit

)))

|(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10098|(% colspan="2" style="width:506px" %)(((

* =0: None

* =1: ODD

* =2: EVEN

)))

|(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10099|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

816

|(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10100|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

817

|(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10101|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100

818

|(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10102|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30

819

|(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10103|(% colspan="2" style="width:506px" %)

820

|(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10104|(% colspan="2" style="width:506px" %)

821

|(% colspan="1" rowspan="11" style="width:102px" %)COM1-3|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10120|(% colspan="2" style="width:506px" %)(((

* =0: RS232

* =1: RS485

* =2: RS422

* =6: RS485-2

)))

|(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10121|(% colspan="2" style="width:506px" %)(((

* =0: 1200

* =1: 2400

* =2: 4800

* =3: 9600

* =4: 19200

* =5: 38400

* =6: 57600

* =7: 115200

* =8: 230400

)))

|(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10122|(% colspan="2" style="width:506px" %)(((

* =7: 7 bit

* =8: 8 bit

)))

|(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10123|(% colspan="2" style="width:506px" %)(((

* =1: 1 bit

* =2: 2 bit

)))

|(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10124|(% colspan="2" style="width:506px" %)(((

* =0: None

* =1: ODD

* =2: EVEN

)))

|(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10125|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

852

|(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10126|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

853

|(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10127|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100

854

|(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10128|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30

855

|(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10129|(% colspan="2" style="width:506px" %)

856

|(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10130|(% colspan="2" style="width:506px" %)

857

|(% colspan="1" rowspan="11" style="width:102px" %)COM2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10072|(% colspan="2" style="width:506px" %)(((

* =0: RS232

* =1: RS485

)))

|(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10073|(% colspan="2" style="width:506px" %)(((

* =0: 1200

* =1: 2400

* =2: 4800

* =3: 9600

* =4: 19200

* =5: 38400

* =6: 57600

* =7: 115200

* =8: 230400

)))

|(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10074|(% colspan="2" style="width:506px" %)(((

* =7: 7 bit

* =8: 8 bit

)))

|(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10075|(% colspan="2" style="width:506px" %)(((

* =1: 1 bit

* =2: 2 bit

)))

|(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10076|(% colspan="2" style="width:506px" %)(((

* =0: None

* =1: ODD

* =2: EVEN

)))

|(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10077|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

886

|(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10078|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

887

|(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10079|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100

888

|(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10080|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30

889

|(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10081|(% colspan="2" style="width:506px" %)

890

|(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10082|(% colspan="2" style="width:506px" %)

891

|(% colspan="1" rowspan="11" style="width:102px" %)COM2-2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10105|(% colspan="2" style="width:506px" %)(((

* =0: RS232

* =1: RS485

)))

|(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10106|(% colspan="2" style="width:506px" %)(((

* =0: 1200

* =1: 2400

* =2: 4800

* =3: 9600

* =4: 19200

* =5: 38400

* =6: 57600

* =7: 115200

* =8: 230400

)))

|(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10107|(% colspan="2" style="width:506px" %)(((

* =7: 7 bit

* =8: 8 bit

)))

|(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10108|(% colspan="2" style="width:506px" %)(((

* =1: 1 bit

* =2: 2 bit

)))

|(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10109|(% colspan="2" style="width:506px" %)(((

* =0: None

* =1: ODD

* =2: EVEN

)))

|(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10110|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

920

|(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10111|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

921

|(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10112|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100

922

|(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10113|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30

923

|(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10114|(% colspan="2" style="width:506px" %)

924

|(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10115|(% colspan="2" style="width:506px" %)

925

|(% colspan="1" rowspan="11" style="width:102px" %)COM3|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10083|(% colspan="2" style="width:506px" %)(((

926

* =1: RS485

927

)))

928

|(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10084|(% colspan="2" style="width:506px" %)(((

* =0: 1200

* =1: 2400

* =2: 4800

* =3: 9600

* =4: 19200

* =5: 38400

* =6: 57600

* =7: 115200

* =8: 230400

)))

|(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10085|(% colspan="2" style="width:506px" %)(((

* =7: 7 bit

* =8: 8 bit

)))

|(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10086|(% colspan="2" style="width:506px" %)(((

* =1: 1 bit

* =2: 2 bit

)))

|(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10087|(% colspan="2" style="width:506px" %)(((

* =0: None

* =1: ODD

* =2: EVEN

)))

|(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10088|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

953

|(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10089|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000

954

|(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10090|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100

955

|(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10091|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30

956

|(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10092|(% colspan="2" style="width:506px" %)

957

|(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10093|(% colspan="2" style="width:506px" %)

958

|(% colspan="1" rowspan="2" style="width:102px" %)CAN port|(% style="width:173px" %)CAN1 baud rate|(% style="width:122px" %)HSW010116|(% style="width:299px" %)(((

959

Unit: K, the baud rate must be an integer, for example, when the baud rate required is 250000, just enter 250.

960

)))|(% colspan="1" rowspan="2" style="width:218px" %)**✎Note: **If baud rate has been modified,please wait 5 seconds,then restart the HMI to take effect.

961

|(% style="width:173px" %)CAN2 baud rate|(% style="width:122px" %)HSW010117|(% style="width:299px" %)Unit: K, the baud rate must be an integer, for example, when the baud rate required is 250000, just enter 250.

962

963

== **Ethernet communication configuration** ==

964

965

(% class="table-bordered" %)

966

|=(% style="width: 40px;" %)**No.**|=(% style="width: 295px;" %)**Function**|=(% style="width: 220px;" %)**Address**|=(% style="width: 336px;" %)**Description**

967

|(% rowspan="7" style="width:40px" %)1|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 1 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11004|(% style="width:336px" %)Device IP address high word 1

968

|(% style="width:220px" %)HSW11005|(% style="width:336px" %)Device IP address high word 2

969

|(% style="width:220px" %)HSW11006|(% style="width:336px" %)Device IP address high word 3

970

|(% style="width:220px" %)HSW11007|(% style="width:336px" %)Device IP address high word 4

971

|(% style="width:220px" %)HSW11008|(% style="width:336px" %)Device Port number

972

|(% style="width:220px" %)HSW11009|=(% style="width: 336px;" %)(((

* =2 TCP

* =3 UDP

)))

|(% style="width:220px" %)HSW11010|(% style="width:336px" %)Reserved

977

|(% rowspan="7" style="width:40px" %)2|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 2 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11011|(% style="width:336px" %)Device IP address high word 1

978

|(% style="width:220px" %)HSW11012|(% style="width:336px" %)Device IP address high word 2

979

|(% style="width:220px" %)HSW11013|(% style="width:336px" %)Device IP address high word 3

980

|(% style="width:220px" %)HSW11014|(% style="width:336px" %)Device IP address high word 4

981

|(% style="width:220px" %)HSW11015|(% style="width:336px" %)Device Port number

982

|(% style="width:220px" %)HSW11016|=(% style="width: 336px;" %)(((

* =2 TCP

* =3 UDP

)))

|(% style="width:220px" %)HSW11017|(% style="width:336px" %)Reserved

987

|(% style="width:40px" %)…|(% style="width:295px" %) |(% style="width:220px" %)…|(% style="width:336px" %)…

988

|(% rowspan="7" style="width:40px" %)32|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 32 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11221|(% style="width:336px" %)Device IP address high word 1

989

|(% style="width:220px" %)HSW11222|(% style="width:336px" %)Device IP address high word 2

990

|(% style="width:220px" %)HSW11223|(% style="width:336px" %)Device IP address high word 3

991

|(% style="width:220px" %)HSW11224|(% style="width:336px" %)Device IP address high word 4

992

|(% style="width:220px" %)HSW11225|(% style="width:336px" %)Device Port number

993

|(% style="width:220px" %)HSW11226|=(% style="width: 336px;" %)2 TCP; =3 UDP

994

|(% style="width:220px" %)HSW11227|(% style="width:336px" %)Reserved

995

996

(% class="wikigeneratedid" %)

997

**✎Note:** The number of Ethernet connections supported by different HMI series varies.

998

999

== **Communication control** ==

1000

1001

(% class="table-bordered" %)

1002

|(% style="width:135px" %)**Communication No.**|(% style="width:102px" %)**Station No.**|(% style="width:185px" %)**Control bit**|(% style="width:191px" %)**Communication lamp**|(% style="width:271px" %)**Description**

1003

|(% colspan="1" rowspan="16" style="width:135px" %)1|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX550.0～HSX550.15|(% style="width:191px" %)HSX558.0～HSX558.15|(% rowspan="160" style="width:271px" %)Communication number refers to the number in "Communication Port Configuration". A number provides 256 device station numbers. Each station number corresponds to a communication control bit and a communication indicator bit. Registers HSX550.0 to HSX805.15 are used to control the station numbers from 0 to 127, and registers HSX1150.0 to HSX1405.15 are used to control station numbers 128 to 255.

1004

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX551.0～HSX551.15|(% style="width:191px" %)HSX559.0～HSX559.15

1005

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX552.0～HSX552.15|(% style="width:191px" %)HSX560.0～HSX560.15

1006

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX553.0～HSX553.15|(% style="width:191px" %)HSX561.0～HSX561.15

1007

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX554.0～HSX554.15|(% style="width:191px" %)HSX562.0～HSX562.15

1008

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX555.0～HSX555.15|(% style="width:191px" %)HSX563.0～HSX563.15

1009

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX556.0～HSX556.15|(% style="width:191px" %)HSX564.0～HSX564.15

1010

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX557.0～HSX557.15|(% style="width:191px" %)HSX565.0～HSX565.15

1011

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1150.0～HSX1150.15|(% style="width:191px" %)HSX1158.0～HSX1158.15

1012

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1151.0～HSX1151.15|(% style="width:191px" %)HSX1159.0～HSX1159.15

1013

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1152.0～HSX1152.15|(% style="width:191px" %)HSX1160.0～HSX1160.15

1014

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1153.0～HSX1153.15|(% style="width:191px" %)HSX1161.0～HSX1161.15

1015

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1154.0～HSX1154.15|(% style="width:191px" %)HSX1162.0～HSX1162.15

1016

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1155.0～HSX1155.15|(% style="width:191px" %)HSX1163.0～HSX1163.15

1017

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1156.0～HSX1156.15|(% style="width:191px" %)HSX1164.0～HSX1164.15

1018

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1157.0～HSX1157.15|(% style="width:191px" %)HSX1165.0～HSX1165.15

1019

|(% colspan="1" rowspan="16" style="width:135px" %)2|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX566.0～HSX566.15|(% style="width:191px" %)HSX574.0～HSX574.15

1020

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX567.0～HSX567.15|(% style="width:191px" %)HSX575.0～HSX575.15

1021

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX568.0～HSX568.15|(% style="width:191px" %)HSX576.0～HSX576.15

1022

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX569.0～HSX569.15|(% style="width:191px" %)HSX577.0～HSX577.15

1023

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX570.0～HSX570.15|(% style="width:191px" %)HSX578.0～HSX578.15

1024

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX571.0～HSX571.15|(% style="width:191px" %)HSX579.0～HSX579.15

1025

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX572.0～HSX572.15|(% style="width:191px" %)HSX580.0～HSX580.15

1026

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX573.0～HSX573.15|(% style="width:191px" %)HSX581.0～HSX581.15

1027

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1166.0～HSX1166.15|(% style="width:191px" %)HSX1174.0～HSX1174.15

1028

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1167.0～HSX1167.15|(% style="width:191px" %)HSX1175.0～HSX1175.15

1029

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1168.0～HSX1168.15|(% style="width:191px" %)HSX1176.0～HSX1176.15

1030

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1169.0～HSX1169.15|(% style="width:191px" %)HSX1177.0～HSX1177.15

1031

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1170.0～HSX1170.15|(% style="width:191px" %)HSX1178.0～HSX1178.15

1032

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1171.0～HSX1171.15|(% style="width:191px" %)HSX1179.0～HSX1179.15

1033

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1172.0～HSX1172.15|(% style="width:191px" %)HSX1180.0～HSX1180.15

1034

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1173.0～HSX1173.15|(% style="width:191px" %)HSX1181.0～HSX1181.15

1035

|(% colspan="1" rowspan="16" style="width:135px" %)3|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX582.0～HSX582.15|(% style="width:191px" %)HSX590.0～HSX590.15

1036

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX583.0～HSX583.15|(% style="width:191px" %)HSX591.0～HSX591.15

1037

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX584.0～HSX584.15|(% style="width:191px" %)HSX592.0～HSX592.15

1038

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX585.0～HSX585.15|(% style="width:191px" %)HSX593.0～HSX593.15

1039

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX586.0～HSX586.15|(% style="width:191px" %)HSX594.0～HSX594.15

1040

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX587.0～HSX587.15|(% style="width:191px" %)HSX595.0～HSX595.15

1041

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX588.0～HSX588.15|(% style="width:191px" %)HSX596.0～HSX596.15

1042

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX589.0～HSX589.15|(% style="width:191px" %)HSX597.0～HSX597.15

1043

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1182.0～HSX1182.15|(% style="width:191px" %)HSX1190.0～HSX1190.15

1044

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1183.0～HSX1183.15|(% style="width:191px" %)HSX1191.0～HSX1191.15

1045

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1184.0～HSX1184.15|(% style="width:191px" %)HSX1192.0～HSX1192.15

1046

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1185.0～HSX1185.15|(% style="width:191px" %)HSX1193.0～HSX1193.15

1047

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1186.0～HSX1186.15|(% style="width:191px" %)HSX1194.0～HSX1194.15

1048

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1187.0～HSX1187.15|(% style="width:191px" %)HSX1195.0～HSX1195.15

1049

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1188.0～HSX1188.15|(% style="width:191px" %)HSX1196.0～HSX1196.15

1050

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1189.0～HSX1189.15|(% style="width:191px" %)HSX1197.0～HSX1197.15

1051

|(% colspan="1" rowspan="16" style="width:135px" %)4|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX598.0～HSX598.15|(% style="width:191px" %)HSX606.0～HSX606.15

1052

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX599.0～HSX599.15|(% style="width:191px" %)HSX607.0～HSX607.15

1053

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX600.0～HSX600.15|(% style="width:191px" %)HSX608.0～HSX608.15

1054

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX601.0～HSX601.15|(% style="width:191px" %)HSX609.0～HSX609.15

1055

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX602.0～HSX602.15|(% style="width:191px" %)HSX610.0～HSX610.15

1056

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX603.0～HSX603.15|(% style="width:191px" %)HSX611.0～HSX611.15

1057

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX604.0～HSX604.15|(% style="width:191px" %)HSX612.0～HSX612.15

1058

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX605.0～HSX605.15|(% style="width:191px" %)HSX613.0～HSX613.15

1059

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1198.0～HSX1198.15|(% style="width:191px" %)HSX1206.0～HSX1206.15

1060

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1199.0～HSX1199.15|(% style="width:191px" %)HSX1207.0～HSX1207.15

1061

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1200.0～HSX1200.15|(% style="width:191px" %)HSX1208.0～HSX1208.15

1062

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1201.0～HSX1201.15|(% style="width:191px" %)HSX1209.0～HSX1209.15

1063

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1202.0～HSX1202.15|(% style="width:191px" %)HSX1210.0～HSX1210.15

1064

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1203.0～HSX1203.15|(% style="width:191px" %)HSX1211.0～HSX1211.15

1065

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1204.0～HSX1204.15|(% style="width:191px" %)HSX1212.0～HSX1212.15

1066

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1205.0～HSX1205.15|(% style="width:191px" %)HSX1213.0～HSX1213.15

1067

|(% colspan="1" rowspan="16" style="width:135px" %)5|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX614.0～HSX614.15|(% style="width:191px" %)HSX622.0～HSX622.15

1068

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX615.0～HSX615.15|(% style="width:191px" %)HSX623.0～HSX623.15

1069

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX616.0～HSX616.15|(% style="width:191px" %)HSX624.0～HSX624.15

1070

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX617.0～HSX617.15|(% style="width:191px" %)HSX625.0～HSX625.15

1071

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX618.0～HSX618.15|(% style="width:191px" %)HSX626.0～HSX626.15

1072

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX619.0～HSX619.15|(% style="width:191px" %)HSX627.0～HSX627.15

1073

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX620.0～HSX620.15|(% style="width:191px" %)HSX628.0～HSX628.15

1074

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX621.0～HSX621.15|(% style="width:191px" %)HSX629.0～HSX629.15

1075

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1214.0～HSX1214.15|(% style="width:191px" %)HSX1222.0～HSX1222.15

1076

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1215.0～HSX1215.15|(% style="width:191px" %)HSX1223.0～HSX1223.15

1077

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1216.0～HSX1216.15|(% style="width:191px" %)HSX1224.0～HSX1224.15

1078

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1217.0～HSX1217.15|(% style="width:191px" %)HSX1225.0～HSX1225.15

1079

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1218.0～HSX1218.15|(% style="width:191px" %)HSX1226.0～HSX1226.15

1080

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1219.0～HSX1219.15|(% style="width:191px" %)HSX1227.0～HSX1227.15

1081

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1220.0～HSX1220.15|(% style="width:191px" %)HSX1228.0～HSX1228.15

1082

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1221.0～HSX1221.15|(% style="width:191px" %)HSX1229.0～HSX1229.15

1083

|(% colspan="1" rowspan="16" style="width:135px" %)6|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX630.0～HSX630.15|(% style="width:191px" %)HSX638.0～HSX638.15

1084

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX631.0～HSX631.15|(% style="width:191px" %)HSX639.0～HSX639.15

1085

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX632.0～HSX632.15|(% style="width:191px" %)HSX640.0～HSX640.15

1086

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX633.0～HSX633.15|(% style="width:191px" %)HSX641.0～HSX641.15

1087

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX634.0～HSX634.15|(% style="width:191px" %)HSX642.0～HSX642.15

1088

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX635.0～HSX635.15|(% style="width:191px" %)HSX643.0～HSX643.15

1089

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX636.0～HSX636.15|(% style="width:191px" %)HSX644.0～HSX644.15

1090

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX637.0～HSX637.15|(% style="width:191px" %)HSX645.0～HSX645.15

1091

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1230.0～HSX1230.15|(% style="width:191px" %)HSX1238.0～HSX1238.15

1092

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1231.0～HSX1231.15|(% style="width:191px" %)HSX1239.0～HSX1239.15

1093

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1232.0～HSX1232.15|(% style="width:191px" %)HSX1240.0～HSX1240.15

1094

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1233.0～HSX1233.15|(% style="width:191px" %)HSX1241.0～HSX1241.15

1095

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1234.0～HSX1234.15|(% style="width:191px" %)HSX1242.0～HSX1242.15

1096

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1235.0～HSX1235.15|(% style="width:191px" %)HSX1243.0～HSX1243.15

1097

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1236.0～HSX1236.15|(% style="width:191px" %)HSX1244.0～HSX1244.15

1098

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1237.0～HSX1237.15|(% style="width:191px" %)HSX1245.0～HSX1245.15

1099

|(% colspan="1" rowspan="16" style="width:135px" %)7|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX646.0～HSX646.15|(% style="width:191px" %)HSX654.0～HSX654.15

1100

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX647.0～HSX647.15|(% style="width:191px" %)HSX655.0～HSX655.15

1101

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX648.0～HSX648.15|(% style="width:191px" %)HSX656.0～HSX656.15

1102

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX649.0～HSX649.15|(% style="width:191px" %)HSX657.0～HSX657.15

1103

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX650.0～HSX650.15|(% style="width:191px" %)HSX658.0～HSX658.15

1104

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX651.0～HSX651.15|(% style="width:191px" %)HSX659.0～HSX659.15

1105

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX652.0～HSX652.15|(% style="width:191px" %)HSX660.0～HSX660.15

1106

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX653.0～HSX653.15|(% style="width:191px" %)HSX661.0～HSX661.15

1107

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1246.0～HSX1246.15|(% style="width:191px" %)HSX1254.0～HSX1254.15

1108

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1247.0～HSX1247.15|(% style="width:191px" %)HSX1255.0～HSX1255.15

1109

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1248.0～HSX1248.15|(% style="width:191px" %)HSX1256.0～HSX1256.15

1110

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1249.0～HSX1249.15|(% style="width:191px" %)HSX1257.0～HSX1257.15

1111

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1250.0～HSX1250.15|(% style="width:191px" %)HSX1258.0～HSX1258.15

1112

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1251.0～HSX1251.15|(% style="width:191px" %)HSX1259.0～HSX1259.15

1113

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1252.0～HSX1252.15|(% style="width:191px" %)HSX1260.0～HSX1260.15

1114

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1253.0～HSX1253.15|(% style="width:191px" %)HSX1261.0～HSX1261.15

1115

|(% colspan="1" rowspan="16" style="width:135px" %)8|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX662.0～HSX662.15|(% style="width:191px" %)HSX670.0～HSX670.15

1116

|(% style="width:102px" %)16～31|(% style="width:185px" %)HSX663.0～HSX663.15|(% style="width:191px" %)HSX671.0～HSX671.15

1117

|(% style="width:102px" %)32～47|(% style="width:185px" %)HSX664.0～HSX664.15|(% style="width:191px" %)HSX672.0～HSX672.15

1118

|(% style="width:102px" %)48～63|(% style="width:185px" %)HSX665.0～HSX665.15|(% style="width:191px" %)HSX673.0～HSX673.15

1119

|(% style="width:102px" %)64～79|(% style="width:185px" %)HSX666.0～HSX666.15|(% style="width:191px" %)HSX674.0～HSX674.15

1120

|(% style="width:102px" %)80～95|(% style="width:185px" %)HSX667.0～HSX667.15|(% style="width:191px" %)HSX675.0～HSX675.15

1121

|(% style="width:102px" %)96～111|(% style="width:185px" %)HSX668.0～HSX668.15|(% style="width:191px" %)HSX676.0～HSX676.15

1122

|(% style="width:102px" %)112～127|(% style="width:185px" %)HSX669.0～HSX669.15|(% style="width:191px" %)HSX677.0～HSX677.15

1123

|(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1262.0～HSX1262.15|(% style="width:191px" %)HSX1270.0～HSX1270.15

1124

|(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1263.0～HSX1263.15|(% style="width:191px" %)HSX1271.0～HSX1271.15

1125

|(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1264.0～HSX1264.15|(% style="width:191px" %)HSX1272.0～HSX1272.15

1126

|(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1265.0～HSX1265.15|(% style="width:191px" %)HSX1273.0～HSX1273.15

1127

|(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1266.0～HSX1266.15|(% style="width:191px" %)HSX1274.0～HSX1274.15

1128

|(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1267.0～HSX1267.15|(% style="width:191px" %)HSX1275.0～HSX1275.15

1129

|(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1268.0～HSX1268.15|(% style="width:191px" %)HSX1276.0～HSX1276.15

1130

|(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1269.0～HSX1269.15|(% style="width:191px" %)HSX1277.0～HSX1277.15

1131

|(% rowspan="4" style="width:135px" %)9|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX678.0~~678.15|(% style="width:191px" %)HSX686.0~~686.15

1132

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX679.0~~679.15|(% style="width:191px" %)HSX687.0~~687.15

1133

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX680.0~~680.15|(% style="width:191px" %)HSX688.0~~688.15

1134

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX681.0~~681.15|(% style="width:191px" %)HSX689.0~~689.15

1135

|(% rowspan="4" style="width:135px" %)10|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX694.0~~694.15|(% style="width:191px" %)HSX702.0~~702.15

1136

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX695.0~~695.15|(% style="width:191px" %)HSX703.0~~703.15

1137

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX696.0~~696.15|(% style="width:191px" %)HSX704.0~~704.15

1138

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX697.0~~697.15|(% style="width:191px" %)HSX705.0~~705.15

1139

|(% rowspan="4" style="width:135px" %)11|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX710.0~~710.15|(% style="width:191px" %)HSX718.0~~718.15

1140

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX711.0~~711.15|(% style="width:191px" %)HSX719.0~~719.15

1141

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX712.0~~712.15|(% style="width:191px" %)HSX720.0~~720.15

1142

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX713.0~~713.15|(% style="width:191px" %)HSX721.0~~721.15

1143

|(% rowspan="4" style="width:135px" %)12|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX726.0~~726.15|(% style="width:191px" %)HSX734.0~~734.15

1144

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX727.0~~727.15|(% style="width:191px" %)HSX735.0~~735.15

1145

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX728.0~~728.15|(% style="width:191px" %)HSX736.0~~736.15

1146

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX729.0~~729.15|(% style="width:191px" %)HSX737.0~~737.15

1147

|(% rowspan="4" style="width:135px" %)13|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX742.0~~742.15|(% style="width:191px" %)HSX750.0~~750.15

1148

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX743.0~~743.15|(% style="width:191px" %)HSX751.0~~751.15

1149

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX744.0~~744.15|(% style="width:191px" %)HSX752.0~~752.15

1150

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX745.0~~745.15|(% style="width:191px" %)HSX753.0~~753.15

1151

|(% rowspan="4" style="width:135px" %)14|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX758.0~~758.15|(% style="width:191px" %)HSX766.0~~766.15

1152

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX759.0~~759.15|(% style="width:191px" %)HSX767.0~~767.15

1153

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX760.0~~760.15|(% style="width:191px" %)HSX768.0~~768.15

1154

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX761.0~~761.15|(% style="width:191px" %)HSX769.0~~769.15

1155

|(% rowspan="4" style="width:135px" %)15|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX774.0~~774.15|(% style="width:191px" %)HSX782.0~~782.15

1156

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX775.0~~775.15|(% style="width:191px" %)HSX783.0~~783.15

1157

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX776.0~~776.15|(% style="width:191px" %)HSX784.0~~784.15

1158

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX777.0~~777.15|(% style="width:191px" %)HSX785.0~~785.15

1159

|(% rowspan="4" style="width:135px" %)16|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX790.0~~790.15|(% style="width:191px" %)HSX798.0~~798.15

1160

|(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX791.0~~791.15|(% style="width:191px" %)HSX799.0~~799.15

1161

|(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX792.0~~792.15|(% style="width:191px" %)HSX800.0~~800.15

1162

|(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX793.0~~793.15|(% style="width:191px" %)HSX801.0~~801.15

Wiki source code of 12 HMI internal registers