Skip to Content

Wiki source code of 12 HMI internal registers

Version 2.2 by Hunter on 2022/07/29 15:12
Show last authors
1 = **Introduction** =
2
3 HMI provide four types of HMI address for user. You can use them as temporary variables of the program. The use is consistent with the way access to the PLC register. You could also reference through the address, PIStudio provides three types of such memory.
4
5 *HSW, HDW, HUW, HAW are word address, HSX, HDX, HUX, HAX are bit address.
6
7 1. **System data area (HSW): **A special register defined by the system.
8 1. **Data storage area (HDW/HDX): **Users store user data.
9 1. **System data area (HUW): **A special register defined by the system.
10 1. **System Data (HAW)**: System register used for power-off save.
11 1. **Recipe index area (RPW): **System register used for recipe index.
12
13 HMI internal registers are divided into bit address and word address, which can be accessed in two ways (take HDW as an example).
14
15 1. Access as word with the prefix "HDW".
16
17 * HDW0 means the 1st word of system data area. HDW1 means the 2nd word of system data area.
18
19 (% start="2" %)
20 1. Access as bit with the prefix "HDX".  The number before "." i".  The number before Access in bit with the prefix "HD".  The number before Access in bit with the prefix "HDX". The number before "." indicates the number of the word. The number after "." indicates the bit number of the word.
21
22 * HDX1020.12 means to access the system data area in bit mode, the specific location is the 13th bit of the 1020 word.
23
24 **✎Note:**
25
26 * Addresses in HDX are the bits from words in HDW, so be careful when using addresses. For example, HDX1020.12 is the 13th bit to access the 1020 word. The value of this bit is the same as that of the word accessed through HDW001020. The 13th bit of this word is actually the same bit as HDX1020.12.
27 * The address of the bit address HDX is with a decimal point while word addresses are integers.
28
29 = **Data storage area (HDW/HDX)** =
30
31 It is used to save the temporary data of project.
32
33 1. Access as word, and serial number range is from HDW0 to HDW299999.
34 1. Access as bit, and serial number range is from HDX0.0 to HDX299999.15.
35
36 = **Power-down save area (HAW/HAX)** =
37
38 It is system registers used for power-off save.
39
40 1. Access as word, and serial number range is from HAW0 to HAW199999.
41 1. Access as bit, and serial number range is from HAX0.0 to HAX199999.15.
42
43 **✎Note:**
44
45 * HAW/HAX is power-down retention. The register of this type is able to save the data before the power-down.
46 * To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save addre
47
48 = **Recipe index area (RPW)** =
49
50 It is system recipe data power-off save register. The range is from RPW000000 to RPW990450.
51
52 **✎Note:**
53
54 * RPW is power-down retention. The register of this type is able to save the data before the power-down.
55 * To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save addre
56
57 = **Single user data area (HUW/HUX)** =
58
59 It is used for system special registers (reserved by system).
60
61 1. Access as word, and serial number range is from HUW0 to HUW199999.
62 1. Access as bit, and serial number range is from HUX0.0 to HUX199999.15.
63
64 **✎Note:**
65
66 * HUW/HUX is a system special register, so please check the system special register list during use. Please use the address specified in the table and do not use the address which is not mentioned in the table.
67
68 (% class="table-bordered" %)
69 |=**Special register address**|=**Description**|=**Function**
70 |=HUW0|Screen switch|A single terminal controls the screen switching, and all terminals do not affect each other.
71 |=HUW110~~HUW119|(% rowspan="26" %)Addresses of the built-in keyboard|The T9 input method stores the selected seria number length
72 |=HUW120~~HUW129|The T9 input method stores the selected Chinese Pinyin length
73 |=HUW135|Input method: first input
74 |=HUW136|Button: T9 Chinese Pinyin page
75 |=HUW137|Button: T9 Chinese characters page
76 |=HUW138|Button: symbol
77 |=HUW139|Button: switch
78 |=HUW140|Button: Chinese characters 1
79 |=HUW142|Button: Chinese characters 2
80 |=HUW144|Button: Chinese characters 3
81 |=HUW146|Button: Chinese characters 4
82 |=HUW148|Button: Chinese characters 5
83 |=HUW150|Button: Chinese characters 6
84 |=HUW152|Button: Chinese characters 7
85 |=HUW154|Button: Chinese characters 8
86 |=HUW156|Button: Chinese characters 9
87 |=HUW158|Button: Chinese characters 10
88 |=HUW160~~HUW169|Button: Chinese Pinyin 1
89 |=HUW170~~HUW179|Button: Chinese Pinyin 2
90 |=HUW180~~HUW189|Button: Chinese Pinyin 3
91 |=HUW190~~HUW199|Button: Chinese Pinyin 4
92 |=HUW200~~HUW699|Input method cache length
93 |=HUW700~~HUW749|Minimum value of the input method
94 |=HUW750~~HUW799|Maximum value of the input method
95 |=HUW800|Case switching of the input method
96 |=HUW801~~HUW900|Input method format cache length
97 |=HUW1000|(% rowspan="12" %)Addresses of user permission|OK (Sign in)
98 |=HUW1001|Result of operation
99 |=HUW1002~~1005|Old password
100 |=HUW1006~~1009|New password
101 |=HUW1010~~1013|Confirm password
102 |=HUW1014~~1029|New user name
103 |=HUW1030~~1157|States information of user permission
104 |=HUW1158~~1335|User name (Only or drop-down list object)
105 |=HUW1336~~1345|User name description or note
106 |=HUW1347|Hidden function configurations
107 |=HUW1348|Permission settings
108 |=HUW1349|Current user name
109 |=HUW1382|User sign in way|(((
110 * 0: Select the user name from drop-down list object for signing in
111 * 1: Enter the user name in Character Input/Display object for signing in (HUW1014)
112 )))
113 |=HUW1400|Time interval from last operation|(((
114 Shows how long the touch screen has not been clicked, in seconds. 32-bit unsigned integer
115
116 **✎Note:** Clicking by different users will only clear the corresponding register of the currently operating terminal, and the registers on other terminals (such as mobile phones, computers) will not be cleared.
117 )))
118 |=HUW1402|Keyboard note|It saves the text information of the keyboard notes when clicking object(HUW1402-HUW1433)
119 |=HUW1436|Current object level|Indicate current object security level
120
121 = **Special data area (HSW/HSX)** =
122
123 It is used for system special registers (reserved by system).
124
125 1. Access as word, and serial number range is from HSW0 to HSW49999. (HSW10000 to HSW19999 are the power-off storage areas)
126 1. Access as bit, and serial number range is from HSX0.0 to HSX49999.15.
127
128 **✎Note:**
129
130 * HSW / HSX are a system special register, so please check the system special register list during use. Please use the address specified in the table and do not use the address which is not mentioned in the table.
131 * To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save address.
132
133 (% class="table-bordered" style="width:1024px" %)
134 |=(% scope="row" style="width: 160px;" %)**Address**|=(% style="width: 282px;" %)**Function**|=(% style="width: 452px;" %)**Description**
135 |=(% style="width: 160px;" %)HSW0|(% style="width:282px" %)Language switch|(% style="width:452px" %)Multiple language could be set in the project, HMI support maximum 8 languages. (Power-down save supported)
136 |=(% style="width: 160px;" %)HSW1|(% style="width:282px" %)Beep frequency|(% style="width:452px" %)Frequency range: 0~~4000
137 |=(% style="width: 160px;" %)HSW2|(% style="width:282px" %)Beep volume|(% style="width:452px" %)Volume range: 0~~80
138 |=(% style="width: 160px;" %)HSW3|(% style="width:282px" %)Beep time|(% style="width:452px" %)Unit: ms
139 |=(% style="width: 160px;" %)HSW4|(% style="width:282px" %)Beep whether enable or not|(% style="width:452px" %)(((
140 * =0: Enable.
141 * =1: Disable.
142 )))
143 |=(% style="width: 160px;" %)HSW5|(% style="width:282px" %)(((
144 Alarm indicator
145 )))|(% style="width:452px" %)(((
146 * =0: Currently no alarm or all alarms have been off.
147 * =1: Currently alarm(s) still keep in on.
148 )))
149 |=(% style="width: 160px;" %)HSW6~~HSW7|(% style="width:282px" %)Number of alarms|(% style="width:452px" %)The number of alarm (it also includes the records of alarm confirmed)
150 |=(% style="width: 160px;" %)HSW8|(% style="width:282px" %)Number of unconfirmed history alarm|(% style="width:452px" %)The number of unconfirmed history alarm
151 |=(% style="width: 160px;" %)HSW9|(% style="width:282px" %)Time out tip|(% style="width:452px" %)(((
152 * =0: Enable
153 * =1: Disable
154 )))
155 |=(% style="width: 160px;" %)HSW12|(% style="width:282px" %)Screen swicth|(% style="width:452px" %)(((
156 * = 0: Only HSW control the screen switch, and the sreens of all users will switch.
157 * = 1: Only HUW control the screen switch, and all users do not affect each other.
158 )))
159 |=(% style="width: 160px;" %)HSW13|(% style="width:282px" %)Screen switch register|(% style="width:452px" %)Equal to different values, the screen jumps to the corresponding screen number of the screen.
160 |=(% style="width: 160px;" %)HSW24|(% style="width:282px" %)Reboot HMI|=(% style="width: 452px;" %)1: Reboot
161 |=(% style="width: 160px;" %)HSW28|(% style="width:282px" %)Local time: year|(% style="width:452px" %)Range: 0~~9999 (system reserved)
162 |=(% style="width: 160px;" %)HSW29|(% style="width:282px" %)Local time: month|(% style="width:452px" %)Range: 01~~12 (system reserved)
163 |=(% style="width: 160px;" %)HSW30|(% style="width:282px" %)Local time: day|(% style="width:452px" %)Range: 01~~31 (system reserved)
164 |=(% style="width: 160px;" %)HSW31|(% style="width:282px" %)Local time: hour|(% style="width:452px" %)Range: 0~~23 (system reserved)
165 |=(% style="width: 160px;" %)HSW32|(% style="width:282px" %)Local time: minute|(% style="width:452px" %)Range: 0~~59 (system reserved)
166 |=(% style="width: 160px;" %)HSW33|(% style="width:282px" %)Local time: second|(% style="width:452px" %)Range: 0~~59 (system reserved)
167 |=(% style="width: 160px;" %)HSW34|(% style="width:282px" %)Local time: week|(% style="width:452px" %)(((
168 * =0: Sunday.
169 * =1: Monday.
170 * =2: Tuesday.
171 * =3: Wednesday.
172 * =4: Thursday.
173 * =5: Friday.
174 * =6: Saturday.
175 )))
176 |=(% style="width: 160px;" %)HSW134|(% style="width:282px" %)(((
177 Whether the Script is read through
178
179
180 )))|(% style="width:452px" %)(((
181 **✎Note:** If want to read-only or write-only, please enable this settings.
182
183 * =0: Read from HMI cache(Default)
184 * =1: Read from PLC directly
185 )))
186 |=(% style="width: 160px;" %)HSW135|(% style="width:282px" %)Confirm installment password|(% style="width:452px" %)Confirm button for installment password
187 |=(% style="width: 160px;" %)HSW151|(% style="width:282px" %)Installment due|(% style="width:452px" %)Number of days to installment due
188 |=(% style="width: 160px;" %)HSW185~~200|(% style="width:282px" %)Installment password|(% style="width:452px" %)Enter installment password
189 |=(% style="width: 160px;" %)HSW242|(% style="width:282px" %)(((
190 Prompt result of recipe operation
191
192 * Upload: Data is written from address to file
193 * Download: Data is written from a file to an address
194 )))|(% style="width:452px" %)(((
195 * =1: Download recipe, start
196 * =2: Download recipe, execution error
197 * =3: Download recipe, files don't exist
198 * =4: Download recipe, members don't exist
199 * =5: Download recipe, groups don't exist
200 * =6: Download recipe, success
201 * =7: Upload recipe, start
202 * =8: Upload recipe, execution error
203 * =9: Upload recipe, files don't exist
204 * =10: Upload recipe, members don't exist
205 * =11: Upload recipe, groups don't exist
206 * =12: Upload recipe, success
207 * =13: Insert recipe, start
208 * =14: Insert recipe, execution error
209 * =15: Insert recipe, files don't exist
210 * =16: Insert recipe, members don't exist
211 * =17: Insert recipe, groups don't exist
212 * =18: Insert recipe, success
213 * =19: Delete recipe, start
214 * =20: Delete recipe, execution error
215 * =21: Delete recipe, files don't exist
216 * =22: Delete recipe, members don't exist
217 * =23: Delete recipe, groups don't exist
218 * =24: Delete recipe, success
219 * =25: Delete and sort recipe, start
220 * =26: Delete recipe and sort, execution error
221 * =27: Delete recipe and sort, files don't exist
222 * =28: Delete recipe and sort, members don't exist
223 * =29: Delete recipe and sort, groups don't exist
224 * =30: Delete recipe and sort, success
225 * =37: CSV recipe files import successfully
226 * =38: CSV recipe files import failed.
227 )))
228 |=(% style="width: 160px;" %)HSW243|(% style="width:282px" %)Prompt result of recipe index|(% style="width:452px" %)(((
229 * =31: Recipe index, start
230 * =32: Recipe index, execution error
231 * =33: Recipe index, files don't exist
232 * =34: Recipe index, members don't exist
233 * =35: Recipe index, groups don't exist
234 * =36: Recipe index, success
235 )))
236 |=(% style="width: 160px;" %)HSW521|(% style="width:282px" %)Delete graph and alarm record|(% style="width:452px" %)(((
237 * =0: No operation
238 * =1: HSX521.0=1, delete all records.
239 * =2: HSX521.1=1, delete all trend graph.
240 * =4: HSX521.2=1, delete all alarms.
241 * =16: HSX521.4=1, delete history XY plot.
242 * =32: HSX521.5=1, delete data records in SD card or flash dish;(Please make a setting which is saved to flash disk or SD card in project setting).
243 * =64: HSX521.6=1, delete alarms records in SD card or flash dish; (Please make a setting which is saved to flash disk or SD card in project setting).
244 )))
245 |=(% style="width: 160px;" %)HSW522|(% style="width:282px" %)Copy and paste the alarm/data files in flash to the USB flash disk|(% style="width:452px" %)(((
246 * =0: No operation
247 * =1: HSX522.0=1, copy all record
248 * =2: HSX522.2=1, copy history XY trend graph
249 * =8: HSX522.3=1, copy alarm record
250 * =32: HSX522.5=1, copy recipe
251 )))
252 |=(% style="width: 160px;" %)HSW523|(% style="width:282px" %)Copy and paste the alarm/data files in flash to the SD card|(% style="width:452px" %)(((
253 * =0: No operation
254 * =1: HSX523.0=1, copy all record
255 * =4: HSX523.2=1, copy history XY trend graph
256 * =8: HSX523.3=1, copy alarm record
257 )))
258 |=(% style="width: 160px;" %)HSW524|(% style="width:282px" %)Copy and paste the alarm/data files in SD card to the USB flash disk|(% style="width:452px" %)(((
259 * =0: no operation
260 * =4: HSX524.2=1, copy history XY trend graph
261 * =8: HSX524.3=1, copy alarm record
262 * =16: HSX524.4=1, copy history alarm record
263 * =32: HSX524.5=1, copy data record
264 )))
265 |=(% style="width: 160px;" %)HSW525|(% style="width:282px" %)Copy and paste the alarm/data files in USB flash disk to SD card|(% style="width:452px" %)(((
266 * =0: no operation
267 * =4: HSX525.2=1, copy history XY trend graph
268 * =8: HSX525.3=1, copy alarm record
269 * =16: HSX525.4=1, copy history alarm record
270 * =32: HSX525.5= 1, copy data record
271 )))
272 |=(% style="width: 160px;" %)HSW526|(% style="width:282px" %)Delete file list|(% style="width:452px" %)(((
273 * =0: no operation
274 * =1: HSX526.0=1, delete designated file
275 * =2: HSX526.1=1, delete all files
276 )))
277 |=(% style="width: 160px;" %)HSW527|(% style="width:282px" %)Eject USB flash disk/SD card|(% style="width:452px" %)(((
278 * =0: No operation
279 * =1: Eject USB flash disk
280 * =2: Eject SD card
281 )))
282 |=(% style="width: 160px;" %)HSW528|(% style="width:282px" %)The state of USB flash disk|(% style="width:452px" %)(((
283 * =1: USB flash disk is detected
284 * =2: Ejecting USB flash disk, please waiting…
285 * =3: USB flash disk ejected
286 )))
287 |=(% style="width: 160px;" %)HSW529|(% style="width:282px" %)The state of SD card|(% style="width:452px" %)(((
288 * =1: SD card is detected
289 * =2: Ejecting SD card, please waiting…
290 * =3: SD card ejected
291 )))
292 |=(% style="width: 160px;" %)HSW550~~849|(% style="width:282px" %)Communication control|(% style="width:452px" %)For communication control and communication lamp (please refer to "[[communication control>>http://13.229.109.52:8080/wiki/pistudio/view/Helps/13.HMI%20internal%20registers/#HCommunicationcontrol]]" sector for detailed)
293 |=(% style="width: 160px;" %)HSW850|(% style="width:282px" %)(((
294 Network state
295
296 (4G, WIFI and Ethernet)
297 )))|(% style="width:452px" %)(((
298 In HMI V1.0
299
300 * =0: Network is disconnected.
301 * =1: only LAN connected, and APP can't access HMI.
302 * =2: WECON Cloud connected , APP and web could access HMI.
303
304 In HMI V2.0
305
306 * =0: Network is disconnected.
307 * =1: Network is connected.
308 )))
309 |=(% style="width: 160px;" %)HSW855|(% style="width:282px" %)Backlight Control|(% style="width:452px" %)(((
310 * HSX855.0=1: turn on the backlight and reset automatically after being triggered.
311 * HSX855.1=1: turn off the backlight and reset automatically after being triggered.
312 )))
313 |=(% style="width: 160px;" %)HSW856|(% style="width:282px" %)Whether to close the indirect screen when the current screen is switched to the other screen)|(% style="width:452px" %)(((
314 * =0: close the sub-screen, including the indirect screen;
315 * =1: not to close.
316 )))
317 |=(% style="width: 160px;" %)HSW857|(% style="width:282px" %)Permission in remote access (web page, mobile APP, cloud platform, etc.)|(% style="width:452px" %)(((
318 * =0: users could switch the screen, control the switch and update data in remote access.
319 * =1: users could only control function switch (only switch the screen), view data and switch state, but could not operate or update them.
320 * =2: users could neither operate the screen switch, nor switch operation and data modification, only view. (The ig series and 8000/9000 series with -R after system upgrade)
321 )))
322 |=(% style="width: 160px;" %)HSW860~~861|(% style="width:282px" %)Data partition remaining space|(% style="width:452px" %)Display the data partition remaining space, updated every minute, unit(**kB**)
323 |=(% style="width: 160px;" %)HSW880|(% style="width:282px" %)Enable data partition remaining space|(% style="width:452px" %)(((
324 ~=1, able to view the data partition remaining space from HSW860~~861.
325
326 ~=Other value except 1, disable the viewing function.
327 )))
328 |=(% style="width: 160px;" %)HSW881|(% style="width:282px" %)Storage of Record files|(% style="width:452px" %)(((
329 It is used for controlling saving alarm/data record files to U disk / SD card.
330
331 * = 0: Save to storage.
332 * = 1: Don't save to storage.
333 )))
334 |=(% style="width: 160px;" %)HSW882|(% style="width:282px" %)Storage device status|(% style="width:452px" %)(((
335 * HDX882.0=0 USB flash doesn't execute storage or storage finished.
336 * HDX882.0=1 USB flash is reading data, don't remove USB flash.
337 * HDX882.1=0 SD card doesn't execute storage or storage finished.
338 * HDX882.1=1 SD card is reading data, don't remove SD card.
339 )))
340 |=(% style="width: 160px;" %)HSW884|(% style="width:282px" %)Enter setup screen|(% style="width:452px" %)(((
341 * = 0: Do not into setup screen
342 * = 1: Enter setup screen
343 )))
344 |=(% style="width: 160px;" %)HSW885|(% style="width:282px" %)When the control object hides the address is read failed (communication failure), set the display mode of the object|(% style="width:452px" %)(((
345 * = 0: displayed by object setting.
346 * =1: control address read failure, the address control of all objects is hidden, not displayed.
347 * =2: control address read failure, the address control of all objects is displayed, not hidden.
348 )))
349 |=(% style="width: 160px;" %)HSW893|(% style="width:282px" %)(((
350 User Permission Control Address, same as HUW1000 feature, please refer to chapter "[[User Permission>>http://13.229.109.52:8080/wiki/pistudio/view/Helps/08.Basic%20Function/#HUserPermission]]"
351
352 **✎Note: **This address can only take effect when it is operated in the real HMI, and the operation is invalid on Web/App side.
353 )))|(% style="width:452px" %)(((
354 * =1: User Log in
355 * =2: Change User password
356 * =3: User Log out
357 * =4: New user
358 * =5: Delete user
359 * =6: Add user rights
360 * =8: Add Hide features
361 * =9: Delete Profile
362 * =10: Export Profile
363 * =11: Import profile
364 * =12: Export log file
365 * =13: Delete log file
366 )))
367 |=(% style="width: 160px;" %)HSW900|(% style="width:282px" %)Quick update frequency settings for objects|(% style="width:452px" %)(((
368 Valid when the object is enabled for "quick update". Default: 5.
369
370 Range: 1 (fastest) ~~ 50 (slowest)
371 )))
372 |=(% style="width: 160px;" %)HSW920|(% style="width:282px" %)Static mode Maximum periods|(% style="width:452px" %)Numeric Input/ Display (range: 0-12)
373 |=(% style="width: 160px;" %)HSW921 ~~ 924|(% style="width:282px" %)Static mode Admin key|(% style="width:452px" %)Character Input/ Display (length: 8)
374 |=(% style="width: 160px;" %)HSW925 ~~ 928|(% style="width:282px" %)1^^st^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
375 |=(% style="width: 160px;" %)HSW929 ~~ 933|(% style="width:282px" %)1^^st^^ expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
376 |=(% style="width: 160px;" %)HSW935 ~~ 938|(% style="width:282px" %)2^^nd^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
377 |=(% style="width: 160px;" %)HSW939 ~~ 943|(% style="width:282px" %)2^^nd ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
378 |=(% style="width: 160px;" %)HSW945 ~~ 948|(% style="width:282px" %)3^^rd^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
379 |=(% style="width: 160px;" %)HSW949 ~~ 953|(% style="width:282px" %)3^^rd ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
380 |=(% style="width: 160px;" %)HSW955 ~~ 958|(% style="width:282px" %)4^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
381 |=(% style="width: 160px;" %)HSW959 ~~ 963|(% style="width:282px" %)4^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
382 |=(% style="width: 160px;" %)HSW965 ~~ 968|(% style="width:282px" %)5^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
383 |=(% style="width: 160px;" %)HSW969 ~~ 973|(% style="width:282px" %)5^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
384 |=(% style="width: 160px;" %)HSW975 ~~ 978|(% style="width:282px" %)6^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
385 |=(% style="width: 160px;" %)HSW979 ~~ 983|(% style="width:282px" %)6^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
386 |=(% style="width: 160px;" %)HSW985 ~~ 988|(% style="width:282px" %)7^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
387 |=(% style="width: 160px;" %)HSW989 ~~ 993|(% style="width:282px" %)7^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
388 |=(% style="width: 160px;" %)HSW995 ~~ 998|(% style="width:282px" %)8^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
389 |=(% style="width: 160px;" %)HSW999 ~~ 1003|(% style="width:282px" %)8^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
390 |=(% style="width: 160px;" %)HSW1005 ~~1008|(% style="width:282px" %)9^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
391 |=(% style="width: 160px;" %)HSW1009 ~~ 1013|(% style="width:282px" %)9^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
392 |=(% style="width: 160px;" %)HSW1015 ~~1018|(% style="width:282px" %)10^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
393 |=(% style="width: 160px;" %)HSW1019 ~~ 1023|(% style="width:282px" %)10^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
394 |=(% style="width: 160px;" %)HSW1025 ~~1028|(% style="width:282px" %)11^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
395 |=(% style="width: 160px;" %)HSW1029 ~~ 1033|(% style="width:282px" %)11^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
396 |=(% style="width: 160px;" %)HSW1035 ~~1038|(% style="width:282px" %)12^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
397 |=(% style="width: 160px;" %)HSW1039 ~~ 1043|(% style="width:282px" %)12^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
398 |=(% style="width: 160px;" %)HSW1046|(% style="width:282px" %)Current period (Static mode)|(% style="width:452px" %)Current period (Range 1-13)
399 |=(% style="width: 160px;" %)HSW1047|(% style="width:282px" %)Save settings (Static mode)|(% style="width:452px" %)(((
400 * HSX1047.0=1: Save static installment information
401 * HSX1047.1=1: Write installment information to registers
402 )))
403 |=(% style="width: 160px;" %)HSW1050~~HSW1065|(% style="width:282px" %)The recipe name that can input csv format|(% style="width:452px" %)Input CSV format recipe file name through "Character Input/ Display".(This function should be used in combination with the recipefunction)
404 |=(% style="width: 160px;" %)HSW1066|(% style="width:282px" %)Configure the type of the CSV file imported|(% style="width:452px" %)(((
405 The CSV file type imported (This function should be used in combination with the recipe function)
406
407 * =0: Import customed CSV file. The data in the file is valid.
408 * =1: Import ordinary recipe files of regular series HMI. The 1st row of the file is invalid.
409 * =2: Import special recipe files of regular series HMI. The 1st and 3nd rows and the 1st colume of the file is invalid.
410 )))
411 |=(% style="width: 160px;" %)HSW1067|(% style="width:282px" %)Location where the CSV file is saved|(% style="width:452px" %)(((
412 Set the path of CSV file (This function should be used in combination with the recipe function)
413
414 * =0: In the CsvFile directory of the USB stick
415 * =1: In the CsvFile directory of the SD card
416 )))
417 |=(% style="width: 160px;" %)HSW1070|(% style="width:282px" %)The time interval (seconds) since the last time the screen was clicked|(% style="width:452px" %)(((
418 Shows how long the current screen has not been clicked, using a decimal unsigned double word (Numeric Input/ Display).
419
420 **✎Note: **This register is cleared to zero regardless of which user clicks on the screen.
421 )))
422 |=(% style="width: 160px;" %)HSW1073|(% style="width:282px" %)Corresponding key value from keyboard|(% style="width:452px" %)Display the key value of the currently pressed key, the key value is shown in Table 1 (not updated when the character input display is being input)
423 |=(% style="width: 160px;" %)HSW1074|(% style="width:282px" %)Keyboard key status|(% style="width:452px" %)Display the current button status (not updated when the numeric input display is being input)(((
424 * =0: key release
425 * =1: key press
426 * =2: Long press the button
427 )))
428 |=(% style="width: 160px;" %)HSW1075|(% style="width:282px" %)Cursor speed|(% style="width:452px" %)Control the cursor movement speed, the range is 0～100, the default is 20
429 |=(% style="width: 160px;" %)HSW1076|(% style="width:282px" %)Cursor x coordinate value|(% style="width:452px" %)Record the x value at the current position of the cursor, range: 0 to screen width -1
430 |=(% style="width: 160px;" %)HSW1077|(% style="width:282px" %)Cursor y coordinate value|(% style="width:452px" %)Record the y value at the current position of the cursor, range: 0 to screen height-1
431 |=(% style="width: 160px;" %)HSW1078|(% style="width:282px" %)Corresponding ASCII code for keyboard keys|(% style="width:452px" %)Only the ASCII value of letters, numbers, and symbols are displayed, and the ASCII value of the function button is not displayed.
432 |=(% style="width: 160px;" %)HSW1079|(% style="width:282px" %)Trigger to set the cursor position and set the Enter key mode|(% style="width:452px" %)(((
433 * HSX1079.0=1: Set the cursor position according to the cursor xy register value;
434 * HSX1079.1=0: When the numeric/character input display is being input, press Enter to end the input, no value/text part is being input, Enter is a normal click;
435 * HSX1079.1=1 Regardless of whether the numeric/character component is inputting the Enter key, only normal click is performed, and the keyboard end input is not performed.
436 )))
437 |=(% style="width: 160px;" %)HSW1083|(% style="width:282px" %)Naming method for printing object screenshots|(% style="width:452px" %)(((
438 Example: The time is 2019-01-04 14:29:10 (523 milliseconds), the screen number is 0, and the object ID is 2.
439
440 * =0: Use year, month, day, hour, minute, second, millisecond, screen number, part number to name, such as: 2019010414291052302.bmp.
441 * =1: Name using year, month, day, hour, minute, and second.
442
443 For example: 20190104142910.bmp.
444 )))
445 |=(% style="width: 160px;" %)HSW1086|(% style="width:282px" %)Control address mapping polling cycle, unit: ms|(% style="width:452px" %)(((
446 Address mapping polling cycle, effective range: 40~~1000ms, default: 300ms.
447
448 * When the set value is greater than 1000, the value is 1000.
449 * When the set value is greater than 1000, it changes to the default value 300
450 )))
451 |=(% style="width: 160px;" %)HSW1087|(% style="width:282px" %)Control write interval in address mapping|(% style="width:452px" %)(((
452 After reading data to the device for N times, Perform an address mapping write operation. N is the interval value. The effective range: 0~~5, and default is 2.
453
454 When N more than 5, it is 5.
455
456 0 is the fastest and 5 is the slowest.
457 )))
458 |=(% style="width: 160px;" %)HSW1088|(% style="width:282px" %)Control the write interval of script|(% style="width:452px" %)(((
459 After reading data to the device for N times, Perform a script write operation. N is the interval value. The effective range: 0~~5, and default is 2.
460
461 When N more than 5, it is 5.
462
463 0 is the fastest and 5 is the slowest.
464 )))
465 |=(% style="width: 160px;" %)HSW1089|(% style="width:282px" %)Control interval of read through|(% style="width:452px" %)(((
466 After reading data to the device for N times, Perform a read through operation. N is the interval value. The effective range: 0~~5, and default is 2.
467
468 When N more than 5, it is 5.
469
470 0 is the fastest and 5 is the slowest.
471 )))
472 |=(% style="width: 160px;" %)HSW1100|(% colspan="1" rowspan="4" style="width:282px" %)Set the Master IP for Multi-link|(% style="width:452px" %)High word 1 for Master IP address of multi-link
473 |=(% style="width: 160px;" %)HSW1101|(% style="width:452px" %)High word 2 for Master IP address of multi-link
474 |=(% style="width: 160px;" %)HSW1102|(% style="width:452px" %)High word 3 for Master IP address of multi-link
475 |=(% style="width: 160px;" %)HSW1103|(% style="width:452px" %)High word 4 for Master IP address of multi-link
476 |=(% style="width: 160px;" %)HSW1104|(% style="width:282px" %)Control connection to Master or not for Multi-link slave device|(% style="width:452px" %)(((
477 * =1: Connect to the Master
478 * =0: Do not connect to Master
479 )))
480 |=(% style="width: 160px;" %)HSW1141|(% style="width:282px" %)Release alarm|(% style="width:452px" %)(((
481 * =0, Default value
482 * =1, Release the alarm generated before the last power-down when starting up
483 )))
484 |=(% style="width: 160px;" %)HSW1450|(% style="width:282px" %)Enable objects level password function|(% style="width:452px" %)(((
485 * =0, Disable
486 * =1, Enable
487 )))
488 |=(% style="width: 160px;" %)HSW1451|(% style="width:282px" %)Whether the object level passwords are independent of each other|(% style="width:452px" %)(((
489 * =0, No, high-level passwords can unlock low-level
490 * = 1, Yes, high-level passwords cannot unlock low-level
491 )))
492 |=(% style="width: 160px;" %)HSW1452|(% style="width:282px" %)Initialization level|(% style="width:452px" %)Initialization level while HMI running
493 |=(% style="width: 160px;" %)HSW1454~~1457|(% style="width:282px" %)Password for Level 1|(% style="width:452px" %)(((
494 Display password for level 1, using character input object, up to 8 characters (numbers, letters (case sensitive))
495 )))
496 |=(% style="width: 160px;" %)HSW1458~~1461|(% style="width:282px" %)Password for Level 2|(% style="width:452px" %)Display password for level 2, using character input object, up to 8 characters (numbers, letters (case sensitive))
497 |=(% style="width: 160px;" %)HSW1462~~1465|(% style="width:282px" %)Password for Level 3|(% style="width:452px" %)Display password for level 3, using character input object, up to 8 characters (numbers, letters (case sensitive))
498 |=(% style="width: 160px;" %)HSW1466~~1469|(% style="width:282px" %)Password for Level 4|(% style="width:452px" %)Display password for level 4, using character input object, up to 8 characters (numbers, letters (case sensitive))
499 |=(% style="width: 160px;" %)HSW1470~~1473|(% style="width:282px" %)Password for Level 5|(% style="width:452px" %)Display password for level 5, using character input object, up to 8 characters (numbers, letters (case sensitive))
500 |=(% style="width: 160px;" %)HSW1474~~1477|(% style="width:282px" %)Password for Level 6|(% style="width:452px" %)Display password for level 6, using character input object, up to 8 characters (numbers, letters (case sensitive))
501 |=(% style="width: 160px;" %)HSW1478~~1481|(% style="width:282px" %)Password for Level 7|(% style="width:452px" %)Display password for level 7, using character input object, up to 8 characters (numbers, letters (case sensitive))
502 |=(% style="width: 160px;" %)HSW1482~~1485|(% style="width:282px" %)Password for Level 8|(% style="width:452px" %)Display password for level 8, using character input object, up to 8 characters (numbers, letters (case sensitive))
503 |=(% style="width: 160px;" %)HSW1486~~1489|(% style="width:282px" %)Password for Level 9|(% style="width:452px" %)Display password for level 9, using character input object, up to 8 characters (numbers, letters (case sensitive))
504 |=(% style="width: 160px;" %)HSW1490~~1493|(% style="width:282px" %)Password for Level 10|(% style="width:452px" %)Display password for level 10, using character input object, up to 8 characters (numbers, letters (case sensitive))
505 |=(% style="width: 160px;" %)HSW1494~~1497|(% style="width:282px" %)Password for Level 11|(% style="width:452px" %)Display password for level 11, using character input object, up to 8 characters (numbers, letters (case sensitive))
506 |=(% style="width: 160px;" %)HSW1498~~1501|(% style="width:282px" %)Password for Level 12|(% style="width:452px" %)Display password for level 12, using character input object, up to 8 characters (numbers, letters (case sensitive))
507 |=(% style="width: 160px;" %)HSW1502|(% style="width:282px" %)Modify password for object level|(% style="width:452px" %)(((
508 * HSX1502.0=1: Modification comfirmed. Save the data of HSW1450~~HSW1501 to a file for immediate effect.
509 * HSX1502.1=1:Modification cancelled. Restore the current data of hSW1450-HSW1501 to the data saved in the file last time.
510 )))
511 |=(% style="width: 160px;" %)HSW1603|(% style="width:282px" %)Number of current unreleased alarms|(% style="width:452px" %)The number of current unreleased alarms in alarm record file.
512 |=(% style="width: 160px;" %)HSW1604|(% style="width:282px" %)The auxiliary judgment address when the control bit in the Object Lock fails to be read|(% style="width:452px" %)(((
513 * =0: The auxiliary address is invalid.
514 * =1: When the communication fails, lock the object.
515 * =2: When the communication fails, unlock the object.
516 * =Others: The auxiliary address is invalid.
517 )))
518 |=(% style="width: 160px;" %)HSW1605|(% style="width:282px" %)BCD format natural decimal control|(% style="width:452px" %)(((
519 Whether to display natural decimals with decimal point in BCD format:
520
521 * 0=Not enabled.
522 * 1=Enable.
523
524 (For example, 56.20 is displayed as 56.2, 33.00 is displayed as 33)
525 )))
526 |=(% style="width: 160px;" %)HSW1606|(% style="width:282px" %)User permission modification control|(% style="width:452px" %)(((
527 * =0: Ordinary users are allowed to modify permissions and other operations
528 * =1: Only the administrator can operate (default is 0)
529 )))
530 |=(% style="width: 160px;" %)HSW1607|(% style="width:282px" %)The spacing value among the drop-down items of the drop-down list|(% style="width:452px" %)10 to 50 is effective, such as: 23 is 2.3 times the height of the object.
531 |=(% style="width: 160px;" %)HSW1611|(% style="width:282px" %)(((
532 Traditional recipe transfer
533 )))|(% style="width:452px" %)(((
534 * =1: download traditional recipe.
535 * =2: upload the traditional recipe.
536 )))
537 |=(% style="width: 160px;" %)HSW1612|(% style="width:282px" %)Traditional Recipe group number|(% style="width:452px" %)Traditional Recipe group number
538 |=(% style="width: 160px;" %)HSW1613|(% style="width:282px" %)Display the status of network card|(% style="width:452px" %)(((
539 * =1: Normal
540 * =Others: Abnormal
541 )))
542 |=(% style="width: 160px;" %)HSW1614~~1623|(% style="width:282px" %)Download speed per second|(% style="width:452px" %)Display the download speed per second. (The value is string)
543 |=(% style="width: 160px;" %)HSW1624~~1633|(% style="width:282px" %)Upnload speed per second|(% style="width:452px" %)Display the upload speed per second. (The value is string)
544 |=(% style="width: 160px;" %)HSW1634~~1643|(% style="width:282px" %)Flow consumption rate|(% style="width:452px" %)Display the total flow rate per second (The value is string)
545 |=(% style="width: 160px;" %)HSW1644~~1653|(% style="width:282px" %)Download flow consumption after power on|(% style="width:452px" %)Display the download flow consumption after power on (The value is string)
546 |=(% style="width: 160px;" %)HSW1654~~1663|(% style="width:282px" %)Upload flow consumption after power on|(% style="width:452px" %)Display the upload flow consumption after power on (The value is string)
547 |=(% style="width: 160px;" %)HSW1664~~1673|(% style="width:282px" %)Total flow consumption after power on|(% style="width:452px" %)Display the total flow consumption after power on (download and upload). (The value is string)
548 |=(% style="width: 160px;" %)HSW1674~~1683|(% style="width:282px" %)Historical flow consumption|(% style="width:452px" %)Display historical flow consumption (download and upload). (The value is string)
549 |=(% style="width: 160px;" %)HSW1684~~1693|(% style="width:282px" %)Flow consumption in 10 minutes|(% style="width:452px" %)Flow consumption in 10 minutes (download and upload). (The value is string)
550 |=(% style="width: 160px;" %)HSW1694~~1703|(% style="width:282px" %)Flow consumption in 30 minutes|(% style="width:452px" %)Flow consumption in 30 minutes (download and upload). (The value is string)
551 |=(% style="width: 160px;" %)HSW1704~~1713|(% style="width:282px" %)Flow consumption in 3 hours|(% style="width:452px" %)Flow consumption in 3 hours (download and upload). (The value is string)
552 |=(% style="width: 160px;" %)HSW1715|(% style="width:282px" %)Reset flow|(% style="width:452px" %)(((
553 * =1: Clear historical flow data and restart the count.
554 * =Others: Invalid
555 )))
556 |=(% style="width: 160px;" %)HSW1719|(% style="width:282px" %)Network status of Ethernet connnecting to server|(% style="width:452px" %)(((
557 * =0: Server connection exception
558 * =1: Server connection is OK
559 )))
560 |=(% style="width: 160px;" %)HSW1720|(% colspan="1" rowspan="12" style="width:282px" %)Related IP register in WIFI network status (It is valid when HMI is connected to WIFI)|(% style="width:452px" %)Local IP address high byte 1
561 |=(% style="width: 160px;" %)HSW1721|(% style="width:452px" %)Local IP address high byte 2
562 |=(% style="width: 160px;" %)HSW1722|(% style="width:452px" %)Local IP address high byte 3
563 |=(% style="width: 160px;" %)HSW1723|(% style="width:452px" %)Local IP address high byte 4
564 |=(% style="width: 160px;" %)HSW1724|(% style="width:452px" %)Local mask IP address high byte 1
565 |=(% style="width: 160px;" %)HSW1725|(% style="width:452px" %)Local mask IP address high byte 2
566 |=(% style="width: 160px;" %)HSW1726|(% style="width:452px" %)Local mask IP address high byte 3
567 |=(% style="width: 160px;" %)HSW1727|(% style="width:452px" %)Local mask IP address high byte 4
568 |=(% style="width: 160px;" %)HSW1728|(% style="width:452px" %)Local gateway IP address high byte 1
569 |=(% style="width: 160px;" %)HSW1729|(% style="width:452px" %)Local gateway IP address high byte 2
570 |=(% style="width: 160px;" %)HSW1730|(% style="width:452px" %)Local gateway IP address high byte 3
571 |=(% style="width: 160px;" %)HSW1731|(% style="width:452px" %)Local gateway IP address high byte 4
572 |=(% style="width: 160px;" %)HSW1733|(% colspan="1" rowspan="6" style="width:282px" %)(((
573 Display the MAC code of current WIFI
574
575 (display in hexadecimal)
576 )))|(% style="width:452px" %)Local MAC address high byte 1 (hexadecimal)
577 |=(% style="width: 160px;" %)HSW1734|(% style="width:452px" %)Local MAC address high byte 2 (hexadecimal)
578 |=(% style="width: 160px;" %)HSW1735|(% style="width:452px" %)Local MAC address high byte 3 (hexadecimal)
579 |=(% style="width: 160px;" %)HSW1736|(% style="width:452px" %)Local MAC address high byte 4 (hexadecimal)
580 |=(% style="width: 160px;" %)HSW1737|(% style="width:452px" %)Local MAC address high byte 5 (hexadecimal)
581 |=(% style="width: 160px;" %)HSW1738|(% style="width:452px" %)Local MAC address high byte 6 (hexadecimal)
582 |=(% style="width: 160px;" %)HSW1739|(% style="width:282px" %)Display the network status of WIFI|(% style="width:452px" %)(((
583 * =0: Server connection exception
584 * =1: Server connection is OK
585 )))
586 |=(% style="width: 160px;" %)HSW1741|(% colspan="1" rowspan="12" style="width:282px" %)Related IP register in 4Gnetwork status (It is valid when HMI is connected to 4G)|(% style="width:452px" %)Local IP address high byte 1
587 |=(% style="width: 160px;" %)HSW1742|(% style="width:452px" %)Local IP address high byte 2
588 |=(% style="width: 160px;" %)HSW1743|(% style="width:452px" %)Local IP address high byte 3
589 |=(% style="width: 160px;" %)HSW1744|(% style="width:452px" %)Local IP address high byte 4
590 |=(% style="width: 160px;" %)HSW1745|(% style="width:452px" %)Local mask IP address high byte 1
591 |=(% style="width: 160px;" %)HSW1746|(% style="width:452px" %)Local mask IP address high byte 2
592 |=(% style="width: 160px;" %)HSW1747|(% style="width:452px" %)Local mask IP address high byte 3
593 |=(% style="width: 160px;" %)HSW1748|(% style="width:452px" %)Local mask IP address high byte 4
594 |=(% style="width: 160px;" %)HSW1749|(% style="width:452px" %)Local gateway IP address high byte 1
595 |=(% style="width: 160px;" %)HSW1750|(% style="width:452px" %)Local gateway IP address high byte 2
596 |=(% style="width: 160px;" %)HSW1751|(% style="width:452px" %)Local gateway IP address high byte 3
597 |=(% style="width: 160px;" %)HSW1752|(% style="width:452px" %)Local gateway IP address high byte 4
598 |=(% style="width: 160px;" %)HSW1754|(% colspan="1" rowspan="6" style="width:282px" %)(((
599 Display the MAC code of current WIFI
600
601 (display in hexadecimal)
602 )))|(% style="width:452px" %)Local MAC address high byte 1 (hexadecimal)
603 |=(% style="width: 160px;" %)HSW1755|(% style="width:452px" %)Local MAC address high byte 2 (hexadecimal)
604 |=(% style="width: 160px;" %)HSW1756|(% style="width:452px" %)Local MAC address high byte 3 (hexadecimal)
605 |=(% style="width: 160px;" %)HSW1757|(% style="width:452px" %)Local MAC address high byte 4 (hexadecimal)
606 |=(% style="width: 160px;" %)HSW1758|(% style="width:452px" %)Local MAC address high byte 5 (hexadecimal)
607 |=(% style="width: 160px;" %)HSW1759|(% style="width:452px" %)Local MAC address high byte 6 (hexadecimal)
608 |=(% style="width: 160px;" %)HSW1760|(% style="width:282px" %)Display 4G network status|(% style="width:452px" %)(((
609 * =0: Server connection exception
610 * =1: Server connection is OK
611 )))
612 |=(% style="width: 160px;" %)HSW1761|(% style="width:282px" %)Display 4G network signal strength|(% style="width:452px" %)Signal strength: 0~~31. The greater the value ,the signal is stronger
613 |=(% style="width: 160px;" %)HSW1852|(% style="width:282px" %)Control the interval in two consecutive clicks|(% style="width:452px" %)Limit range: 1~~500ms. The default is 100 ms.
614 |=(% style="width: 160px;" %)HSW1853|(% style="width:282px" %)File format for exporting data records to USB flash drive or SD card|(% style="width:452px" %)(((
615 * =0: db database
616 * =1: CSV
617 )))
618 |=(% style="width: 160px;" %)HSW1854|(% style="width:282px" %)High and low word conversion type|(% style="width:452px" %)(((
619 * =0: use the old high-low word conversion (default)
620 * =1: usie the new high-low word conversion
621 )))
622 |=(% style="width: 160px;" %)HSW1855|(% style="width:282px" %)Screen Lock prompt display control|(% style="width:452px" %)(((
623 Control whether the screen lock prompt is displayed,
624
625 * =0: display(default value)
626 * =Other: no display.
627 )))
628 |=(% style="width: 160px;" %)HSW1856|(% style="width:282px" %)Display map fence drawing status|(% style="width:452px" %)(((
629 * =0: no map fence
630 * =1: The map fence is drawn and the device is inside the fence
631 * =2: The map fence is drawn and the device is outside the fence
632 )))
633 |=(% style="width: 160px;" %)HSW1857|(% style="width:282px" %)USB disk download |(% style="width:452px" %)(((
634 * =0: download project
635 * =1: download firmware
636 * =2: enter the background
637 )))
638 |=(% style="width: 160px;" %)HSW10000~~19999|(% style="width:282px" %)Power-down storage area|(% style="width:452px" %)After restart, the data remains
639 |=(% style="width: 160px;" %)HSW10035|(% rowspan="13" style="width:282px" %)(((
640 **✎Note: **Only valid when the HMI is plugged into the Ethernet cable.
641
642 1. If Ethernet settings is enabled in project parameters, this register displays the set value.
643 1. If Ethernet settings is not enabled in project parameters, IP would automatically obtained IP.
644 1. If HMI is not connected to the network, the register is displayed as 0 whether the engineering parameters are set.
645 1. 4. All IP registers of HMI are read-only.
646 )))|(% style="width:452px" %)Local IP address high byte 1
647 |=(% style="width: 160px;" %)HSW10036|(% style="width:452px" %)Local IP address high byte 2
648 |=(% style="width: 160px;" %)HSW10037|(% style="width:452px" %)Local IP address high byte 3
649 |=(% style="width: 160px;" %)HSW10038|(% style="width:452px" %)Local IP address high byte 4
650 |=(% style="width: 160px;" %)HSW10039|(% style="width:452px" %)Local mask IP address high byte 1
651 |=(% style="width: 160px;" %)HSW10040|(% style="width:452px" %)Local mask IP address high byte 2
652 |=(% style="width: 160px;" %)HSW10041|(% style="width:452px" %)Local mask IP address high byte 3
653 |=(% style="width: 160px;" %)HSW10042|(% style="width:452px" %)Local mask IP address high byte 4
654 |=(% style="width: 160px;" %)HSW10043|(% style="width:452px" %)Local gateway address high byte 1
655 |=(% style="width: 160px;" %)HSW10044|(% style="width:452px" %)Local gateway address high byte 2
656 |=(% style="width: 160px;" %)HSW10045|(% style="width:452px" %)Local gateway address high byte 3
657 |=(% style="width: 160px;" %)HSW10046|(% style="width:452px" %)Local gateway address high byte 4
658 |=(% style="width: 160px;" %)HSW10047|(% style="width:452px" %)Local port address
659 |=(% style="width: 160px;" %)HSW10048|(% rowspan="6" style="width:282px" %)(((
660 Displays the MAC code of the current network card
661
662 (Hexadecimal display)
663 )))|(% style="width:452px" %)Local MAC code high word 1
664 |=(% style="width: 160px;" %)HSW10049|(% style="width:452px" %)Local MAC code high word 2
665 |=(% style="width: 160px;" %)HSW10050|(% style="width:452px" %)Local MAC code high word 3
666 |=(% style="width: 160px;" %)HSW10051|(% style="width:452px" %)Local MAC code high word 4
667 |=(% style="width: 160px;" %)HSW10052|(% style="width:452px" %)Local MAC code high word 5
668 |=(% style="width: 160px;" %)HSW10053|(% style="width:452px" %)Local MAC code high word 6
669 |=(% style="width: 160px;" %)HSW10118|(% colspan="1" rowspan="2" style="width:282px" %)TSAP settings for HMI in the Siemens logo! 8 protocol|(% style="width:452px" %)HMI local TSAP, which corresponds to the remote TSAP of PLC
670 |=(% style="width: 160px;" %)HSW10119|(% style="width:452px" %)HMI remote TSAP, which corresponds to the local TSAP of PLC
671 |=(% style="width: 160px;" %)HSW10461~~10493|(% style="width:282px" %)Remote access password|(% style="width:452px" %)8-character remote access password
672 |=(% style="width: 160px;" %)HSW10494~~10558|(% style="width:282px" %)Machine ID (Read only)|(% style="width:452px" %)Machine ID for remote access (read only 64-bit)
673 |=(% style="width: 160px;" %)HSW10576|(% style="width:282px" %)Save dynamic installment settings|(% style="width:452px" %)HSX10576.0=1: Save the set dynamic installment information
674 |=(% style="width: 160px;" %)HSW10577|(% style="width:282px" %)Control address for installment|(% style="width:452px" %)(((
675 * HSX10577.0=0: disable dynamic installment
676 * HSX10577.0=1: enable dynamic installment
677 * HSX10577.1=0: disable static installment
678 * HSX10577.1=1: enable static installment
679 )))
680 |=(% style="width: 160px;" %)HSW10578-10583|(% style="width:282px" %)Password for dynamic installment|(% style="width:452px" %)Character Input/ Display (length: 6)
681 |=(% style="width: 160px;" %)HSW10584-10586|(% style="width:282px" %)Expiry time of dynamic installment|(% style="width:452px" %)Expiry time: YYYYMMDD (Numeric Input/ Display)
682 |=(% style="width: 160px;" %)HSW10587-10589|(% style="width:282px" %)Last expiry time of dynamic installment|(% style="width:452px" %)Expiry time: YYYYMMDD (Numeric Input/ Display)
683 |=(% style="width: 160px;" %)HSW10590|(% style="width:282px" %)Background light time|(% style="width:452px" %)(((
684 Set the light time for background
685
686 * =0: The screen backlight is always on.
687 * =Others: The screen backlight is on for a period of time and then turns off. The length of time is controlled by the value of the register address. Unit: second.
688 )))
689 |=(% style="width: 160px;" %)HSW10591|(% style="width:282px" %)Backlight brightness adjustment|(% style="width:452px" %)Backlight brightness range: 1 (darkest) ~~ 100 (brightest)
690 |=(% style="width: 160px;" %)HSW10603|(% style="width:282px" %)Set the printer to print orientation|(% style="width:452px" %)(((
691 Set the print direction:
692
693 * =1: Forward printing
694 * =2: Reverse print
695 * =Other: Forward print
696 )))
697 |=(% style="width: 160px;" %)HSW10604|(% style="width:282px" %)Print dot type|(% style="width:452px" %)(((
698 * =1: new firmware 8 dot matrix type
699 * =2: new firmware 24 dot matrix type
700 * =3: old firmware 8 dot matrix type
701 * =4: old firmware 24 dot matrix type
702 * =Other: new firmware 8 dot matrix type
703 )))
704 |=(% style="width: 160px;" %)HSW10605|(% style="width:282px" %)Print width of printer|(% style="width:452px" %)Set the width of the printer to print (in pixels), such as HSW10605 = 394: The printer supports images with a print width of 394 pixels
705 |=(% style="width: 160px;" %)HSW10606|(% style="width:282px" %)Printer instruction type|(% style="width:452px" %)(((
706 * =1: Graphic print type
707 * =2: Dot density printing type
708 * =3: special for EPSON printer
709 )))
710 |=(% style="width: 160px;" %)HSW10607|(% style="width:282px" %)Printer paper cutting function|(% style="width:452px" %)(((
711 * =1: Enable
712 * =2: Disable
713 )))
714 |=(% style="width: 160px;" %)HSW10608|(% style="width:282px" %)Print the alignment of the text|(% style="width:452px" %)(((
715 * =1: Left alignment
716 * =2: Center alignment
717 * =3: Right alignment
718 )))
719 |=(% style="width: 160px;" %)HSW10610|(% style="width:282px" %)Set weconcloud server|(% style="width:452px" %)(((
720 * =0: Select the server configured in "Project Settings"
721 * =1: select Server 1
722 * =2: select Server 2
723 )))
724 |=(% style="width: 160px;" %)HSW11750|(% style="width:282px" %)Set the language of the Message List prompt** (ie series)**|(% style="width:452px" %)(((
725 * =0: which is followed the project language
726 * =1: English
727 * =2: Chinese
728 )))
729 |=(% style="width: 160px;" %)HSW11756|(% style="width:282px" %)(((
730 Access permission restrictions
731
732 (ig series and** **8000/9000 series with -R after system upgrade)
733 )))|(% style="width:452px" %)(((
734 * =0: LAN or the external network both OK
735 * =1: Only LAN access
736 * =2: Only external network can access
737 )))
738 |=(% style="width: 160px;" %)HSW11757|(% style="width:282px" %)Enable the valid date of the dynamic installment password|(% style="width:452px" %)(((
739 * =0: Disabled
740 * =1: Enable
741 )))
742 |=(% style="width: 160px;" %)HSW11758|(% style="width:282px" %)Enable Screensaver|(% style="width:452px" %)(((
743 * =0: Disabled
744 * =1: Enable
745 )))
746 |=(% style="width: 160px;" %)HSW11759|(% style="width:282px" %)Screensaver interval time|(% style="width:452px" %)(((
747 Set the time how long will enter Screensaver (Range 10~~43200s)
748 )))
749 |=(% style="width: 160px;" %)HSW11760|(% style="width:282px" %)Screensaver countdown|(% style="width:452px" %)Display the countdown to enter the Screensaver, unit: second.
750 |=(% style="width: 160px;" %)HSW11761|(% style="width:282px" %)Screensaver screen number|(% style="width:452px" %)Set the screen number for Screensaver
751
752 == **Serial port communication configuration** ==
753
754 (% class="table-bordered" %)
755 |=(% style="width: 102px;" %)Port|=(% style="width: 173px;" %)**Function**|=(% style="width: 122px;" %)**Address**|=(% colspan="2" style="width: 506px;" %)**Description**
756 |(% colspan="1" rowspan="11" style="width:102px" %)COM1|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10061|(% colspan="2" style="width:506px" %)(((
757 * =0: RS232
758 * =1: RS485
759 * =2: RS422
760 )))
761 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10062|(% colspan="2" style="width:506px" %)(((
762 * =0: 1200
763 * =1: 2400
764 * =2: 4800
765 * =3: 9600
766 * =4: 19200
767 * =5: 38400
768 * =6: 57600
769 * =7: 115200
770 * =8: 230400
771 )))
772 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10063|(% colspan="2" style="width:506px" %)(((
773 * =7: 7 bit
774 * =8: 8 bit
775 )))
776 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10064|(% colspan="2" style="width:506px" %)(((
777 * =1: 1 bit
778 * =2: 2 bit
779 )))
780 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10065|(% colspan="2" style="width:506px" %)(((
781 * =0: None
782 * =1: ODD
783 * =2: EVEN
784 )))
785 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10066|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
786 |(% style="width:173px" %)reveive timeout|(% style="width:122px" %)HSW10067|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
787 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10068|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
788 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10069|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~300
789 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10070|(% colspan="2" style="width:506px" %)
790 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10071|(% colspan="2" style="width:506px" %)
791 |(% colspan="1" rowspan="11" style="width:102px" %)COM1-2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10094|(% colspan="2" style="width:506px" %)(((
792 * =0: RS232
793 * =1: RS485
794 * =2: RS422
795 * =6: RS485-2
796 )))
797 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10095|(% colspan="2" style="width:506px" %)(((
798 * =0: 1200
799 * =1: 2400
800 * =2: 4800
801 * =3: 9600
802 * =4: 19200
803 * =5: 38400
804 * =6: 57600
805 * =7: 115200
806 * =8: 230400
807 )))
808 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10096|(% colspan="2" style="width:506px" %)(((
809 * =7: 7 bit
810 * =8: 8 bit
811 )))
812 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10097|(% colspan="2" style="width:506px" %)(((
813 * =1: 1 bit
814 * =2: 2 bit
815 )))
816 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10098|(% colspan="2" style="width:506px" %)(((
817 * =0: None
818 * =1: ODD
819 * =2: EVEN
820 )))
821 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10099|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
822 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10100|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
823 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10101|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
824 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10102|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
825 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10103|(% colspan="2" style="width:506px" %)
826 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10104|(% colspan="2" style="width:506px" %)
827 |(% colspan="1" rowspan="11" style="width:102px" %)COM1-3|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10120|(% colspan="2" style="width:506px" %)(((
828 * =0: RS232
829 * =1: RS485
830 * =2: RS422
831 * =6: RS485-2
832 )))
833 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10121|(% colspan="2" style="width:506px" %)(((
834 * =0: 1200
835 * =1: 2400
836 * =2: 4800
837 * =3: 9600
838 * =4: 19200
839 * =5: 38400
840 * =6: 57600
841 * =7: 115200
842 * =8: 230400
843 )))
844 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10122|(% colspan="2" style="width:506px" %)(((
845 * =7: 7 bit
846 * =8: 8 bit
847 )))
848 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10123|(% colspan="2" style="width:506px" %)(((
849 * =1: 1 bit
850 * =2: 2 bit
851 )))
852 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10124|(% colspan="2" style="width:506px" %)(((
853 * =0: None
854 * =1: ODD
855 * =2: EVEN
856 )))
857 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10125|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
858 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10126|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
859 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10127|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
860 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10128|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
861 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10129|(% colspan="2" style="width:506px" %)
862 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10130|(% colspan="2" style="width:506px" %)
863 |(% colspan="1" rowspan="11" style="width:102px" %)COM2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10072|(% colspan="2" style="width:506px" %)(((
864 * =0: RS232
865 * =1: RS485
866 )))
867 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10073|(% colspan="2" style="width:506px" %)(((
868 * =0: 1200
869 * =1: 2400
870 * =2: 4800
871 * =3: 9600
872 * =4: 19200
873 * =5: 38400
874 * =6: 57600
875 * =7: 115200
876 * =8: 230400
877 )))
878 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10074|(% colspan="2" style="width:506px" %)(((
879 * =7: 7 bit
880 * =8: 8 bit
881 )))
882 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10075|(% colspan="2" style="width:506px" %)(((
883 * =1: 1 bit
884 * =2: 2 bit
885 )))
886 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10076|(% colspan="2" style="width:506px" %)(((
887 * =0: None
888 * =1: ODD
889 * =2: EVEN
890 )))
891 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10077|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
892 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10078|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
893 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10079|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
894 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10080|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
895 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10081|(% colspan="2" style="width:506px" %)
896 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10082|(% colspan="2" style="width:506px" %)
897 |(% colspan="1" rowspan="11" style="width:102px" %)COM2-2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10105|(% colspan="2" style="width:506px" %)(((
898 * =0: RS232
899 * =1: RS485
900 )))
901 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10106|(% colspan="2" style="width:506px" %)(((
902 * =0: 1200
903 * =1: 2400
904 * =2: 4800
905 * =3: 9600
906 * =4: 19200
907 * =5: 38400
908 * =6: 57600
909 * =7: 115200
910 * =8: 230400
911 )))
912 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10107|(% colspan="2" style="width:506px" %)(((
913 * =7: 7 bit
914 * =8: 8 bit
915 )))
916 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10108|(% colspan="2" style="width:506px" %)(((
917 * =1: 1 bit
918 * =2: 2 bit
919 )))
920 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10109|(% colspan="2" style="width:506px" %)(((
921 * =0: None
922 * =1: ODD
923 * =2: EVEN
924 )))
925 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10110|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
926 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10111|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
927 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10112|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
928 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10113|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
929 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10114|(% colspan="2" style="width:506px" %)
930 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10115|(% colspan="2" style="width:506px" %)
931 |(% colspan="1" rowspan="11" style="width:102px" %)COM3|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10083|(% colspan="2" style="width:506px" %)(((
932 * =1: RS485
933 )))
934 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10084|(% colspan="2" style="width:506px" %)(((
935 * =0: 1200
936 * =1: 2400
937 * =2: 4800
938 * =3: 9600
939 * =4: 19200
940 * =5: 38400
941 * =6: 57600
942 * =7: 115200
943 * =8: 230400
944 )))
945 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10085|(% colspan="2" style="width:506px" %)(((
946 * =7: 7 bit
947 * =8: 8 bit
948 )))
949 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10086|(% colspan="2" style="width:506px" %)(((
950 * =1: 1 bit
951 * =2: 2 bit
952 )))
953 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10087|(% colspan="2" style="width:506px" %)(((
954 * =0: None
955 * =1: ODD
956 * =2: EVEN
957 )))
958 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10088|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
959 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10089|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
960 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10090|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
961 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10091|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
962 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10092|(% colspan="2" style="width:506px" %)
963 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10093|(% colspan="2" style="width:506px" %)
964 |(% colspan="1" rowspan="2" style="width:102px" %)CAN port|(% style="width:173px" %)CAN1 baud rate|(% style="width:122px" %)HSW010116|(% style="width:299px" %)(((
965 Unit: K, the baud rate must be an integer, for example, when the baud rate required is 250000, just enter 250.
966 )))|(% colspan="1" rowspan="2" style="width:218px" %)**✎Note: **If baud rate has been modified,please wait 5 seconds,then restart the HMI to take effect.
967 |(% style="width:173px" %)CAN2 baud rate|(% style="width:122px" %)HSW010117|(% style="width:299px" %)Unit: K, the baud rate must be an integer, for example, when the baud rate required is 250000, just enter 250.
968
969 == **Ethernet communication configuration** ==
970
971 (% class="table-bordered" %)
972 |=(% style="width: 40px;" %)**No.**|=(% style="width: 295px;" %)**Function**|=(% style="width: 220px;" %)**Address**|=(% style="width: 336px;" %)**Description**
973 |(% rowspan="7" style="width:40px" %)1|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 1 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11004|(% style="width:336px" %)Device IP address high word 1
974 |(% style="width:220px" %)HSW11005|(% style="width:336px" %)Device IP address high word 2
975 |(% style="width:220px" %)HSW11006|(% style="width:336px" %)Device IP address high word 3
976 |(% style="width:220px" %)HSW11007|(% style="width:336px" %)Device IP address high word 4
977 |(% style="width:220px" %)HSW11008|(% style="width:336px" %)Device Port number
978 |(% style="width:220px" %)HSW11009|=(% style="width: 336px;" %)(((
979 * =2 TCP
980 * =3 UDP
981 )))
982 |(% style="width:220px" %)HSW11010|(% style="width:336px" %)Reserved
983 |(% rowspan="7" style="width:40px" %)2|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 2 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11011|(% style="width:336px" %)Device IP address high word 1
984 |(% style="width:220px" %)HSW11012|(% style="width:336px" %)Device IP address high word 2
985 |(% style="width:220px" %)HSW11013|(% style="width:336px" %)Device IP address high word 3
986 |(% style="width:220px" %)HSW11014|(% style="width:336px" %)Device IP address high word 4
987 |(% style="width:220px" %)HSW11015|(% style="width:336px" %)Device Port number
988 |(% style="width:220px" %)HSW11016|=(% style="width: 336px;" %)(((
989 * =2 TCP
990 * =3 UDP
991 )))
992 |(% style="width:220px" %)HSW11017|(% style="width:336px" %)Reserved
993 |(% style="width:40px" %)…|(% style="width:295px" %) |(% style="width:220px" %)…|(% style="width:336px" %)…
994 |(% rowspan="7" style="width:40px" %)32|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 32 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11221|(% style="width:336px" %)Device IP address high word 1
995 |(% style="width:220px" %)HSW11222|(% style="width:336px" %)Device IP address high word 2
996 |(% style="width:220px" %)HSW11223|(% style="width:336px" %)Device IP address high word 3
997 |(% style="width:220px" %)HSW11224|(% style="width:336px" %)Device IP address high word 4
998 |(% style="width:220px" %)HSW11225|(% style="width:336px" %)Device Port number
999 |(% style="width:220px" %)HSW11226|=(% style="width: 336px;" %)2 TCP; =3 UDP
1000 |(% style="width:220px" %)HSW11227|(% style="width:336px" %)Reserved
1001
1002 (% class="wikigeneratedid" %)
1003 **✎Note:** The number of Ethernet connections supported by different HMI series varies.
1004
1005 == **Communication control** ==
1006
1007 (% class="table-bordered" %)
1008 |(% style="width:135px" %)**Communication No.**|(% style="width:102px" %)**Station No.**|(% style="width:185px" %)**Control bit**|(% style="width:191px" %)**Communication lamp**|(% style="width:271px" %)**Description**
1009 |(% colspan="1" rowspan="16" style="width:135px" %)1|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX550.0～HSX550.15|(% style="width:191px" %)HSX558.0～HSX558.15|(% rowspan="160" style="width:271px" %)Communication number refers to the number in "Communication Port Configuration". A number provides 256 device station numbers. Each station number corresponds to a communication control bit and a communication indicator bit. Registers HSX550.0 to HSX805.15 are used to control the station numbers from 0 to 127, and registers HSX1150.0 to HSX1405.15 are used to control station numbers 128 to 255.
1010 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX551.0～HSX551.15|(% style="width:191px" %)HSX559.0～HSX559.15
1011 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX552.0～HSX552.15|(% style="width:191px" %)HSX560.0～HSX560.15
1012 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX553.0～HSX553.15|(% style="width:191px" %)HSX561.0～HSX561.15
1013 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX554.0～HSX554.15|(% style="width:191px" %)HSX562.0～HSX562.15
1014 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX555.0～HSX555.15|(% style="width:191px" %)HSX563.0～HSX563.15
1015 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX556.0～HSX556.15|(% style="width:191px" %)HSX564.0～HSX564.15
1016 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX557.0～HSX557.15|(% style="width:191px" %)HSX565.0～HSX565.15
1017 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1150.0～HSX1150.15|(% style="width:191px" %)HSX1158.0～HSX1158.15
1018 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1151.0～HSX1151.15|(% style="width:191px" %)HSX1159.0～HSX1159.15
1019 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1152.0～HSX1152.15|(% style="width:191px" %)HSX1160.0～HSX1160.15
1020 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1153.0～HSX1153.15|(% style="width:191px" %)HSX1161.0～HSX1161.15
1021 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1154.0～HSX1154.15|(% style="width:191px" %)HSX1162.0～HSX1162.15
1022 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1155.0～HSX1155.15|(% style="width:191px" %)HSX1163.0～HSX1163.15
1023 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1156.0～HSX1156.15|(% style="width:191px" %)HSX1164.0～HSX1164.15
1024 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1157.0～HSX1157.15|(% style="width:191px" %)HSX1165.0～HSX1165.15
1025 |(% colspan="1" rowspan="16" style="width:135px" %)2|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX566.0～HSX566.15|(% style="width:191px" %)HSX574.0～HSX574.15
1026 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX567.0～HSX567.15|(% style="width:191px" %)HSX575.0～HSX575.15
1027 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX568.0～HSX568.15|(% style="width:191px" %)HSX576.0～HSX576.15
1028 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX569.0～HSX569.15|(% style="width:191px" %)HSX577.0～HSX577.15
1029 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX570.0～HSX570.15|(% style="width:191px" %)HSX578.0～HSX578.15
1030 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX571.0～HSX571.15|(% style="width:191px" %)HSX579.0～HSX579.15
1031 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX572.0～HSX572.15|(% style="width:191px" %)HSX580.0～HSX580.15
1032 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX573.0～HSX573.15|(% style="width:191px" %)HSX581.0～HSX581.15
1033 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1166.0～HSX1166.15|(% style="width:191px" %)HSX1174.0～HSX1174.15
1034 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1167.0～HSX1167.15|(% style="width:191px" %)HSX1175.0～HSX1175.15
1035 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1168.0～HSX1168.15|(% style="width:191px" %)HSX1176.0～HSX1176.15
1036 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1169.0～HSX1169.15|(% style="width:191px" %)HSX1177.0～HSX1177.15
1037 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1170.0～HSX1170.15|(% style="width:191px" %)HSX1178.0～HSX1178.15
1038 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1171.0～HSX1171.15|(% style="width:191px" %)HSX1179.0～HSX1179.15
1039 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1172.0～HSX1172.15|(% style="width:191px" %)HSX1180.0～HSX1180.15
1040 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1173.0～HSX1173.15|(% style="width:191px" %)HSX1181.0～HSX1181.15
1041 |(% colspan="1" rowspan="16" style="width:135px" %)3|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX582.0～HSX582.15|(% style="width:191px" %)HSX590.0～HSX590.15
1042 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX583.0～HSX583.15|(% style="width:191px" %)HSX591.0～HSX591.15
1043 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX584.0～HSX584.15|(% style="width:191px" %)HSX592.0～HSX592.15
1044 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX585.0～HSX585.15|(% style="width:191px" %)HSX593.0～HSX593.15
1045 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX586.0～HSX586.15|(% style="width:191px" %)HSX594.0～HSX594.15
1046 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX587.0～HSX587.15|(% style="width:191px" %)HSX595.0～HSX595.15
1047 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX588.0～HSX588.15|(% style="width:191px" %)HSX596.0～HSX596.15
1048 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX589.0～HSX589.15|(% style="width:191px" %)HSX597.0～HSX597.15
1049 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1182.0～HSX1182.15|(% style="width:191px" %)HSX1190.0～HSX1190.15
1050 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1183.0～HSX1183.15|(% style="width:191px" %)HSX1191.0～HSX1191.15
1051 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1184.0～HSX1184.15|(% style="width:191px" %)HSX1192.0～HSX1192.15
1052 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1185.0～HSX1185.15|(% style="width:191px" %)HSX1193.0～HSX1193.15
1053 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1186.0～HSX1186.15|(% style="width:191px" %)HSX1194.0～HSX1194.15
1054 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1187.0～HSX1187.15|(% style="width:191px" %)HSX1195.0～HSX1195.15
1055 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1188.0～HSX1188.15|(% style="width:191px" %)HSX1196.0～HSX1196.15
1056 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1189.0～HSX1189.15|(% style="width:191px" %)HSX1197.0～HSX1197.15
1057 |(% colspan="1" rowspan="16" style="width:135px" %)4|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX598.0～HSX598.15|(% style="width:191px" %)HSX606.0～HSX606.15
1058 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX599.0～HSX599.15|(% style="width:191px" %)HSX607.0～HSX607.15
1059 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX600.0～HSX600.15|(% style="width:191px" %)HSX608.0～HSX608.15
1060 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX601.0～HSX601.15|(% style="width:191px" %)HSX609.0～HSX609.15
1061 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX602.0～HSX602.15|(% style="width:191px" %)HSX610.0～HSX610.15
1062 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX603.0～HSX603.15|(% style="width:191px" %)HSX611.0～HSX611.15
1063 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX604.0～HSX604.15|(% style="width:191px" %)HSX612.0～HSX612.15
1064 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX605.0～HSX605.15|(% style="width:191px" %)HSX613.0～HSX613.15
1065 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1198.0～HSX1198.15|(% style="width:191px" %)HSX1206.0～HSX1206.15
1066 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1199.0～HSX1199.15|(% style="width:191px" %)HSX1207.0～HSX1207.15
1067 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1200.0～HSX1200.15|(% style="width:191px" %)HSX1208.0～HSX1208.15
1068 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1201.0～HSX1201.15|(% style="width:191px" %)HSX1209.0～HSX1209.15
1069 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1202.0～HSX1202.15|(% style="width:191px" %)HSX1210.0～HSX1210.15
1070 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1203.0～HSX1203.15|(% style="width:191px" %)HSX1211.0～HSX1211.15
1071 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1204.0～HSX1204.15|(% style="width:191px" %)HSX1212.0～HSX1212.15
1072 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1205.0～HSX1205.15|(% style="width:191px" %)HSX1213.0～HSX1213.15
1073 |(% colspan="1" rowspan="16" style="width:135px" %)5|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX614.0～HSX614.15|(% style="width:191px" %)HSX622.0～HSX622.15
1074 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX615.0～HSX615.15|(% style="width:191px" %)HSX623.0～HSX623.15
1075 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX616.0～HSX616.15|(% style="width:191px" %)HSX624.0～HSX624.15
1076 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX617.0～HSX617.15|(% style="width:191px" %)HSX625.0～HSX625.15
1077 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX618.0～HSX618.15|(% style="width:191px" %)HSX626.0～HSX626.15
1078 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX619.0～HSX619.15|(% style="width:191px" %)HSX627.0～HSX627.15
1079 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX620.0～HSX620.15|(% style="width:191px" %)HSX628.0～HSX628.15
1080 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX621.0～HSX621.15|(% style="width:191px" %)HSX629.0～HSX629.15
1081 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1214.0～HSX1214.15|(% style="width:191px" %)HSX1222.0～HSX1222.15
1082 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1215.0～HSX1215.15|(% style="width:191px" %)HSX1223.0～HSX1223.15
1083 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1216.0～HSX1216.15|(% style="width:191px" %)HSX1224.0～HSX1224.15
1084 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1217.0～HSX1217.15|(% style="width:191px" %)HSX1225.0～HSX1225.15
1085 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1218.0～HSX1218.15|(% style="width:191px" %)HSX1226.0～HSX1226.15
1086 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1219.0～HSX1219.15|(% style="width:191px" %)HSX1227.0～HSX1227.15
1087 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1220.0～HSX1220.15|(% style="width:191px" %)HSX1228.0～HSX1228.15
1088 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1221.0～HSX1221.15|(% style="width:191px" %)HSX1229.0～HSX1229.15
1089 |(% colspan="1" rowspan="16" style="width:135px" %)6|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX630.0～HSX630.15|(% style="width:191px" %)HSX638.0～HSX638.15
1090 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX631.0～HSX631.15|(% style="width:191px" %)HSX639.0～HSX639.15
1091 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX632.0～HSX632.15|(% style="width:191px" %)HSX640.0～HSX640.15
1092 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX633.0～HSX633.15|(% style="width:191px" %)HSX641.0～HSX641.15
1093 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX634.0～HSX634.15|(% style="width:191px" %)HSX642.0～HSX642.15
1094 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX635.0～HSX635.15|(% style="width:191px" %)HSX643.0～HSX643.15
1095 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX636.0～HSX636.15|(% style="width:191px" %)HSX644.0～HSX644.15
1096 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX637.0～HSX637.15|(% style="width:191px" %)HSX645.0～HSX645.15
1097 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1230.0～HSX1230.15|(% style="width:191px" %)HSX1238.0～HSX1238.15
1098 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1231.0～HSX1231.15|(% style="width:191px" %)HSX1239.0～HSX1239.15
1099 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1232.0～HSX1232.15|(% style="width:191px" %)HSX1240.0～HSX1240.15
1100 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1233.0～HSX1233.15|(% style="width:191px" %)HSX1241.0～HSX1241.15
1101 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1234.0～HSX1234.15|(% style="width:191px" %)HSX1242.0～HSX1242.15
1102 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1235.0～HSX1235.15|(% style="width:191px" %)HSX1243.0～HSX1243.15
1103 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1236.0～HSX1236.15|(% style="width:191px" %)HSX1244.0～HSX1244.15
1104 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1237.0～HSX1237.15|(% style="width:191px" %)HSX1245.0～HSX1245.15
1105 |(% colspan="1" rowspan="16" style="width:135px" %)7|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX646.0～HSX646.15|(% style="width:191px" %)HSX654.0～HSX654.15
1106 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX647.0～HSX647.15|(% style="width:191px" %)HSX655.0～HSX655.15
1107 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX648.0～HSX648.15|(% style="width:191px" %)HSX656.0～HSX656.15
1108 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX649.0～HSX649.15|(% style="width:191px" %)HSX657.0～HSX657.15
1109 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX650.0～HSX650.15|(% style="width:191px" %)HSX658.0～HSX658.15
1110 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX651.0～HSX651.15|(% style="width:191px" %)HSX659.0～HSX659.15
1111 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX652.0～HSX652.15|(% style="width:191px" %)HSX660.0～HSX660.15
1112 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX653.0～HSX653.15|(% style="width:191px" %)HSX661.0～HSX661.15
1113 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1246.0～HSX1246.15|(% style="width:191px" %)HSX1254.0～HSX1254.15
1114 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1247.0～HSX1247.15|(% style="width:191px" %)HSX1255.0～HSX1255.15
1115 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1248.0～HSX1248.15|(% style="width:191px" %)HSX1256.0～HSX1256.15
1116 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1249.0～HSX1249.15|(% style="width:191px" %)HSX1257.0～HSX1257.15
1117 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1250.0～HSX1250.15|(% style="width:191px" %)HSX1258.0～HSX1258.15
1118 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1251.0～HSX1251.15|(% style="width:191px" %)HSX1259.0～HSX1259.15
1119 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1252.0～HSX1252.15|(% style="width:191px" %)HSX1260.0～HSX1260.15
1120 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1253.0～HSX1253.15|(% style="width:191px" %)HSX1261.0～HSX1261.15
1121 |(% colspan="1" rowspan="16" style="width:135px" %)8|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX662.0～HSX662.15|(% style="width:191px" %)HSX670.0～HSX670.15
1122 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX663.0～HSX663.15|(% style="width:191px" %)HSX671.0～HSX671.15
1123 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX664.0～HSX664.15|(% style="width:191px" %)HSX672.0～HSX672.15
1124 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX665.0～HSX665.15|(% style="width:191px" %)HSX673.0～HSX673.15
1125 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX666.0～HSX666.15|(% style="width:191px" %)HSX674.0～HSX674.15
1126 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX667.0～HSX667.15|(% style="width:191px" %)HSX675.0～HSX675.15
1127 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX668.0～HSX668.15|(% style="width:191px" %)HSX676.0～HSX676.15
1128 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX669.0～HSX669.15|(% style="width:191px" %)HSX677.0～HSX677.15
1129 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1262.0～HSX1262.15|(% style="width:191px" %)HSX1270.0～HSX1270.15
1130 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1263.0～HSX1263.15|(% style="width:191px" %)HSX1271.0～HSX1271.15
1131 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1264.0～HSX1264.15|(% style="width:191px" %)HSX1272.0～HSX1272.15
1132 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1265.0～HSX1265.15|(% style="width:191px" %)HSX1273.0～HSX1273.15
1133 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1266.0～HSX1266.15|(% style="width:191px" %)HSX1274.0～HSX1274.15
1134 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1267.0～HSX1267.15|(% style="width:191px" %)HSX1275.0～HSX1275.15
1135 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1268.0～HSX1268.15|(% style="width:191px" %)HSX1276.0～HSX1276.15
1136 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1269.0～HSX1269.15|(% style="width:191px" %)HSX1277.0～HSX1277.15
1137 |(% rowspan="4" style="width:135px" %)9|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX678.0~~678.15|(% style="width:191px" %)HSX686.0~~686.15
1138 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX679.0~~679.15|(% style="width:191px" %)HSX687.0~~687.15
1139 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX680.0~~680.15|(% style="width:191px" %)HSX688.0~~688.15
1140 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX681.0~~681.15|(% style="width:191px" %)HSX689.0~~689.15
1141 |(% rowspan="4" style="width:135px" %)10|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX694.0~~694.15|(% style="width:191px" %)HSX702.0~~702.15
1142 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX695.0~~695.15|(% style="width:191px" %)HSX703.0~~703.15
1143 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX696.0~~696.15|(% style="width:191px" %)HSX704.0~~704.15
1144 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX697.0~~697.15|(% style="width:191px" %)HSX705.0~~705.15
1145 |(% rowspan="4" style="width:135px" %)11|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX710.0~~710.15|(% style="width:191px" %)HSX718.0~~718.15
1146 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX711.0~~711.15|(% style="width:191px" %)HSX719.0~~719.15
1147 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX712.0~~712.15|(% style="width:191px" %)HSX720.0~~720.15
1148 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX713.0~~713.15|(% style="width:191px" %)HSX721.0~~721.15
1149 |(% rowspan="4" style="width:135px" %)12|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX726.0~~726.15|(% style="width:191px" %)HSX734.0~~734.15
1150 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX727.0~~727.15|(% style="width:191px" %)HSX735.0~~735.15
1151 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX728.0~~728.15|(% style="width:191px" %)HSX736.0~~736.15
1152 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX729.0~~729.15|(% style="width:191px" %)HSX737.0~~737.15
1153 |(% rowspan="4" style="width:135px" %)13|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX742.0~~742.15|(% style="width:191px" %)HSX750.0~~750.15
1154 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX743.0~~743.15|(% style="width:191px" %)HSX751.0~~751.15
1155 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX744.0~~744.15|(% style="width:191px" %)HSX752.0~~752.15
1156 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX745.0~~745.15|(% style="width:191px" %)HSX753.0~~753.15
1157 |(% rowspan="4" style="width:135px" %)14|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX758.0~~758.15|(% style="width:191px" %)HSX766.0~~766.15
1158 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX759.0~~759.15|(% style="width:191px" %)HSX767.0~~767.15
1159 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX760.0~~760.15|(% style="width:191px" %)HSX768.0~~768.15
1160 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX761.0~~761.15|(% style="width:191px" %)HSX769.0~~769.15
1161 |(% rowspan="4" style="width:135px" %)15|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX774.0~~774.15|(% style="width:191px" %)HSX782.0~~782.15
1162 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX775.0~~775.15|(% style="width:191px" %)HSX783.0~~783.15
1163 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX776.0~~776.15|(% style="width:191px" %)HSX784.0~~784.15
1164 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX777.0~~777.15|(% style="width:191px" %)HSX785.0~~785.15
1165 |(% rowspan="4" style="width:135px" %)16|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX790.0~~790.15|(% style="width:191px" %)HSX798.0~~798.15
1166 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX791.0~~791.15|(% style="width:191px" %)HSX799.0~~799.15
1167 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX792.0~~792.15|(% style="width:191px" %)HSX800.0~~800.15
1168 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX793.0~~793.15|(% style="width:191px" %)HSX801.0~~801.15