Skip to Content

Wiki source code of 12 HMI internal registers

Version 3.1 by Stone Wu on 2022/08/03 10:03
Show last authors
1 = **Introduction** =
2
3 HMI provide four types of HMI address for user. You can use them as temporary variables of the program. The use is consistent with the way access to the PLC register. You could also reference through the address, PIStudio provides three types of such memory.
4
5 *HSW, HDW, HUW, HAW are word address, HSX, HDX, HUX, HAX are bit address.
6
7 1. **System data area (HSW): **A special register defined by the system.
8 1. **Data storage area (HDW/HDX): **Users store user data.
9 1. **System data area (HUW): **A special register defined by the system.
10 1. **System Data (HAW)**: System register used for power-off save.
11 1. **Recipe index area (RPW): **System register used for recipe index.
12
13 HMI internal registers are divided into bit address and word address, which can be accessed in two ways (take HDW as an example).
14
15 * Access as word with the prefix "HDW".
16 ** HDW0 means the 1st word of system data area. HDW1 means the 2nd word of system data area.
17 * Access as bit with the prefix "HDX".  The number before "." i".  The number before Access in bit with the prefix "HD".  The number before Access in bit with the prefix "HDX". The number before "." indicates the number of the word. The number after "." indicates the bit number of the word.
18 ** HDX1020.12 means to access the system data area in bit mode, the specific location is the 13th bit of the 1020 word.
19
20 (% class="box infomessage" %)
21 (((
22 **✎Note:**
23
24 * Addresses in HDX are the bits from words in HDW, so be careful when using addresses. For example, HDX1020.12 is the 13th bit to access the 1020 word. The value of this bit is the same as that of the word accessed through HDW001020. The 13th bit of this word is actually the same bit as HDX1020.12.
25 * The address of the bit address HDX is with a decimal point while word addresses are integers.
26 )))
27
28 = **Data storage area (HDW/HDX)** =
29
30 It is used to save the temporary data of project.
31
32 1. Access as word, and serial number range is from HDW0 to HDW299999.
33 1. Access as bit, and serial number range is from HDX0.0 to HDX299999.15.
34
35 = **Power-down save area (HAW/HAX)** =
36
37 It is system registers used for power-off save.
38
39 1. Access as word, and serial number range is from HAW0 to HAW199999.
40 1. Access as bit, and serial number range is from HAX0.0 to HAX199999.15.
41
42 (% class="box infomessage" %)
43 (((
44 **✎Note:**
45
46 * HAW/HAX is power-down retention. The register of this type is able to save the data before the power-down.
47 * To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save addre
48 )))
49
50 = **Recipe index area (RPW)** =
51
52 It is system recipe data power-off save register. The range is from RPW000000 to RPW990450.
53
54 **✎Note:**
55
56 * RPW is power-down retention. The register of this type is able to save the data before the power-down.
57 * To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save addre
58
59 = **Single user data area (HUW/HUX)** =
60
61 It is used for system special registers (reserved by system).
62
63 1. Access as word, and serial number range is from HUW0 to HUW199999.
64 1. Access as bit, and serial number range is from HUX0.0 to HUX199999.15.
65
66 **✎Note:**
67
68 * HUW/HUX is a system special register, so please check the system special register list during use. Please use the address specified in the table and do not use the address which is not mentioned in the table.
69
70 (% class="table-bordered" %)
71 |=**Special register address**|=**Description**|=**Function**
72 |=HUW0|Screen switch|A single terminal controls the screen switching, and all terminals do not affect each other.
73 |=HUW110~~HUW119|(% rowspan="26" %)Addresses of the built-in keyboard|The T9 input method stores the selected seria number length
74 |=HUW120~~HUW129|The T9 input method stores the selected Chinese Pinyin length
75 |=HUW135|Input method: first input
76 |=HUW136|Button: T9 Chinese Pinyin page
77 |=HUW137|Button: T9 Chinese characters page
78 |=HUW138|Button: symbol
79 |=HUW139|Button: switch
80 |=HUW140|Button: Chinese characters 1
81 |=HUW142|Button: Chinese characters 2
82 |=HUW144|Button: Chinese characters 3
83 |=HUW146|Button: Chinese characters 4
84 |=HUW148|Button: Chinese characters 5
85 |=HUW150|Button: Chinese characters 6
86 |=HUW152|Button: Chinese characters 7
87 |=HUW154|Button: Chinese characters 8
88 |=HUW156|Button: Chinese characters 9
89 |=HUW158|Button: Chinese characters 10
90 |=HUW160~~HUW169|Button: Chinese Pinyin 1
91 |=HUW170~~HUW179|Button: Chinese Pinyin 2
92 |=HUW180~~HUW189|Button: Chinese Pinyin 3
93 |=HUW190~~HUW199|Button: Chinese Pinyin 4
94 |=HUW200~~HUW699|Input method cache length
95 |=HUW700~~HUW749|Minimum value of the input method
96 |=HUW750~~HUW799|Maximum value of the input method
97 |=HUW800|Case switching of the input method
98 |=HUW801~~HUW900|Input method format cache length
99 |=HUW1000|(% rowspan="12" %)Addresses of user permission|OK (Sign in)
100 |=HUW1001|Result of operation
101 |=HUW1002~~1005|Old password
102 |=HUW1006~~1009|New password
103 |=HUW1010~~1013|Confirm password
104 |=HUW1014~~1029|New user name
105 |=HUW1030~~1157|States information of user permission
106 |=HUW1158~~1335|User name (Only or drop-down list object)
107 |=HUW1336~~1345|User name description or note
108 |=HUW1347|Hidden function configurations
109 |=HUW1348|Permission settings
110 |=HUW1349|Current user name
111 |=HUW1382|User sign in way|(((
112 * 0: Select the user name from drop-down list object for signing in
113 * 1: Enter the user name in Character Input/Display object for signing in (HUW1014)
114 )))
115 |=HUW1400|Time interval from last operation|(((
116 Shows how long the touch screen has not been clicked, in seconds. 32-bit unsigned integer
117
118 **✎Note:** Clicking by different users will only clear the corresponding register of the currently operating terminal, and the registers on other terminals (such as mobile phones, computers) will not be cleared.
119 )))
120 |=HUW1402|Keyboard note|It saves the text information of the keyboard notes when clicking object(HUW1402-HUW1433)
121 |=HUW1436|Current object level|Indicate current object security level
122
123 = **Special data area (HSW/HSX)** =
124
125 It is used for system special registers (reserved by system).
126
127 1. Access as word, and serial number range is from HSW0 to HSW49999. (HSW10000 to HSW19999 are the power-off storage areas)
128 1. Access as bit, and serial number range is from HSX0.0 to HSX49999.15.
129
130 **✎Note:**
131
132 * HSW / HSX are a system special register, so please check the system special register list during use. Please use the address specified in the table and do not use the address which is not mentioned in the table.
133 * To avoid possible device failure, do not immediately power off and reboot when configuring the power-down save address.
134
135 (% class="table-bordered" style="width:1024px" %)
136 |=(% scope="row" style="width: 160px;" %)**Address**|=(% style="width: 282px;" %)**Function**|=(% style="width: 452px;" %)**Description**
137 |=(% style="width: 160px;" %)HSW0|(% style="width:282px" %)Language switch|(% style="width:452px" %)Multiple language could be set in the project, HMI support maximum 8 languages. (Power-down save supported)
138 |=(% style="width: 160px;" %)HSW1|(% style="width:282px" %)Beep frequency|(% style="width:452px" %)Frequency range: 0~~4000
139 |=(% style="width: 160px;" %)HSW2|(% style="width:282px" %)Beep volume|(% style="width:452px" %)Volume range: 0~~80
140 |=(% style="width: 160px;" %)HSW3|(% style="width:282px" %)Beep time|(% style="width:452px" %)Unit: ms
141 |=(% style="width: 160px;" %)HSW4|(% style="width:282px" %)Beep whether enable or not|(% style="width:452px" %)(((
142 * =0: Enable.
143 * =1: Disable.
144 )))
145 |=(% style="width: 160px;" %)HSW5|(% style="width:282px" %)(((
146 Alarm indicator
147 )))|(% style="width:452px" %)(((
148 * =0: Currently no alarm or all alarms have been off.
149 * =1: Currently alarm(s) still keep in on.
150 )))
151 |=(% style="width: 160px;" %)HSW6~~HSW7|(% style="width:282px" %)Number of alarms|(% style="width:452px" %)The number of alarm (it also includes the records of alarm confirmed)
152 |=(% style="width: 160px;" %)HSW8|(% style="width:282px" %)Number of unconfirmed history alarm|(% style="width:452px" %)The number of unconfirmed history alarm
153 |=(% style="width: 160px;" %)HSW9|(% style="width:282px" %)Time out tip|(% style="width:452px" %)(((
154 * =0: Enable
155 * =1: Disable
156 )))
157 |=(% style="width: 160px;" %)HSW12|(% style="width:282px" %)Screen swicth|(% style="width:452px" %)(((
158 * = 0: Only HSW control the screen switch, and the sreens of all users will switch.
159 * = 1: Only HUW control the screen switch, and all users do not affect each other.
160 )))
161 |=(% style="width: 160px;" %)HSW13|(% style="width:282px" %)Screen switch register|(% style="width:452px" %)Equal to different values, the screen jumps to the corresponding screen number of the screen.
162 |=(% style="width: 160px;" %)HSW24|(% style="width:282px" %)Reboot HMI|=(% style="width: 452px;" %)1: Reboot
163 |=(% style="width: 160px;" %)HSW28|(% style="width:282px" %)Local time: year|(% style="width:452px" %)Range: 0~~9999 (system reserved)
164 |=(% style="width: 160px;" %)HSW29|(% style="width:282px" %)Local time: month|(% style="width:452px" %)Range: 01~~12 (system reserved)
165 |=(% style="width: 160px;" %)HSW30|(% style="width:282px" %)Local time: day|(% style="width:452px" %)Range: 01~~31 (system reserved)
166 |=(% style="width: 160px;" %)HSW31|(% style="width:282px" %)Local time: hour|(% style="width:452px" %)Range: 0~~23 (system reserved)
167 |=(% style="width: 160px;" %)HSW32|(% style="width:282px" %)Local time: minute|(% style="width:452px" %)Range: 0~~59 (system reserved)
168 |=(% style="width: 160px;" %)HSW33|(% style="width:282px" %)Local time: second|(% style="width:452px" %)Range: 0~~59 (system reserved)
169 |=(% style="width: 160px;" %)HSW34|(% style="width:282px" %)Local time: week|(% style="width:452px" %)(((
170 * =0: Sunday.
171 * =1: Monday.
172 * =2: Tuesday.
173 * =3: Wednesday.
174 * =4: Thursday.
175 * =5: Friday.
176 * =6: Saturday.
177 )))
178 |=(% style="width: 160px;" %)HSW134|(% style="width:282px" %)(((
179 Whether the Script is read through
180
181
182 )))|(% style="width:452px" %)(((
183 **✎Note:** If want to read-only or write-only, please enable this settings.
184
185 * =0: Read from HMI cache(Default)
186 * =1: Read from PLC directly
187 )))
188 |=(% style="width: 160px;" %)HSW135|(% style="width:282px" %)Confirm installment password|(% style="width:452px" %)Confirm button for installment password
189 |=(% style="width: 160px;" %)HSW151|(% style="width:282px" %)Installment due|(% style="width:452px" %)Number of days to installment due
190 |=(% style="width: 160px;" %)HSW185~~200|(% style="width:282px" %)Installment password|(% style="width:452px" %)Enter installment password
191 |=(% style="width: 160px;" %)HSW242|(% style="width:282px" %)(((
192 Prompt result of recipe operation
193
194 * Upload: Data is written from address to file
195 * Download: Data is written from a file to an address
196 )))|(% style="width:452px" %)(((
197 * =1: Download recipe, start
198 * =2: Download recipe, execution error
199 * =3: Download recipe, files don't exist
200 * =4: Download recipe, members don't exist
201 * =5: Download recipe, groups don't exist
202 * =6: Download recipe, success
203 * =7: Upload recipe, start
204 * =8: Upload recipe, execution error
205 * =9: Upload recipe, files don't exist
206 * =10: Upload recipe, members don't exist
207 * =11: Upload recipe, groups don't exist
208 * =12: Upload recipe, success
209 * =13: Insert recipe, start
210 * =14: Insert recipe, execution error
211 * =15: Insert recipe, files don't exist
212 * =16: Insert recipe, members don't exist
213 * =17: Insert recipe, groups don't exist
214 * =18: Insert recipe, success
215 * =19: Delete recipe, start
216 * =20: Delete recipe, execution error
217 * =21: Delete recipe, files don't exist
218 * =22: Delete recipe, members don't exist
219 * =23: Delete recipe, groups don't exist
220 * =24: Delete recipe, success
221 * =25: Delete and sort recipe, start
222 * =26: Delete recipe and sort, execution error
223 * =27: Delete recipe and sort, files don't exist
224 * =28: Delete recipe and sort, members don't exist
225 * =29: Delete recipe and sort, groups don't exist
226 * =30: Delete recipe and sort, success
227 * =37: CSV recipe files import successfully
228 * =38: CSV recipe files import failed.
229 )))
230 |=(% style="width: 160px;" %)HSW243|(% style="width:282px" %)Prompt result of recipe index|(% style="width:452px" %)(((
231 * =31: Recipe index, start
232 * =32: Recipe index, execution error
233 * =33: Recipe index, files don't exist
234 * =34: Recipe index, members don't exist
235 * =35: Recipe index, groups don't exist
236 * =36: Recipe index, success
237 )))
238 |=(% style="width: 160px;" %)HSW521|(% style="width:282px" %)Delete graph and alarm record|(% style="width:452px" %)(((
239 * =0: No operation
240 * =1: HSX521.0=1, delete all records.
241 * =2: HSX521.1=1, delete all trend graph.
242 * =4: HSX521.2=1, delete all alarms.
243 * =16: HSX521.4=1, delete history XY plot.
244 * =32: HSX521.5=1, delete data records in SD card or flash dish;(Please make a setting which is saved to flash disk or SD card in project setting).
245 * =64: HSX521.6=1, delete alarms records in SD card or flash dish; (Please make a setting which is saved to flash disk or SD card in project setting).
246 )))
247 |=(% style="width: 160px;" %)HSW522|(% style="width:282px" %)Copy and paste the alarm/data files in flash to the USB flash disk|(% style="width:452px" %)(((
248 * =0: No operation
249 * =1: HSX522.0=1, copy all record
250 * =2: HSX522.2=1, copy history XY trend graph
251 * =8: HSX522.3=1, copy alarm record
252 * =32: HSX522.5=1, copy recipe
253 )))
254 |=(% style="width: 160px;" %)HSW523|(% style="width:282px" %)Copy and paste the alarm/data files in flash to the SD card|(% style="width:452px" %)(((
255 * =0: No operation
256 * =1: HSX523.0=1, copy all record
257 * =4: HSX523.2=1, copy history XY trend graph
258 * =8: HSX523.3=1, copy alarm record
259 )))
260 |=(% style="width: 160px;" %)HSW524|(% style="width:282px" %)Copy and paste the alarm/data files in SD card to the USB flash disk|(% style="width:452px" %)(((
261 * =0: no operation
262 * =4: HSX524.2=1, copy history XY trend graph
263 * =8: HSX524.3=1, copy alarm record
264 * =16: HSX524.4=1, copy history alarm record
265 * =32: HSX524.5=1, copy data record
266 )))
267 |=(% style="width: 160px;" %)HSW525|(% style="width:282px" %)Copy and paste the alarm/data files in USB flash disk to SD card|(% style="width:452px" %)(((
268 * =0: no operation
269 * =4: HSX525.2=1, copy history XY trend graph
270 * =8: HSX525.3=1, copy alarm record
271 * =16: HSX525.4=1, copy history alarm record
272 * =32: HSX525.5= 1, copy data record
273 )))
274 |=(% style="width: 160px;" %)HSW526|(% style="width:282px" %)Delete file list|(% style="width:452px" %)(((
275 * =0: no operation
276 * =1: HSX526.0=1, delete designated file
277 * =2: HSX526.1=1, delete all files
278 )))
279 |=(% style="width: 160px;" %)HSW527|(% style="width:282px" %)Eject USB flash disk/SD card|(% style="width:452px" %)(((
280 * =0: No operation
281 * =1: Eject USB flash disk
282 * =2: Eject SD card
283 )))
284 |=(% style="width: 160px;" %)HSW528|(% style="width:282px" %)The state of USB flash disk|(% style="width:452px" %)(((
285 * =1: USB flash disk is detected
286 * =2: Ejecting USB flash disk, please waiting…
287 * =3: USB flash disk ejected
288 )))
289 |=(% style="width: 160px;" %)HSW529|(% style="width:282px" %)The state of SD card|(% style="width:452px" %)(((
290 * =1: SD card is detected
291 * =2: Ejecting SD card, please waiting…
292 * =3: SD card ejected
293 )))
294 |=(% style="width: 160px;" %)HSW550~~849|(% style="width:282px" %)Communication control|(% style="width:452px" %)For communication control and communication lamp (please refer to "[[communication control>>http://13.229.109.52:8080/wiki/pistudio/view/Helps/13.HMI%20internal%20registers/#HCommunicationcontrol]]" sector for detailed)
295 |=(% style="width: 160px;" %)HSW850|(% style="width:282px" %)(((
296 Network state
297
298 (4G, WIFI and Ethernet)
299 )))|(% style="width:452px" %)(((
300 In HMI V1.0
301
302 * =0: Network is disconnected.
303 * =1: only LAN connected, and APP can't access HMI.
304 * =2: WECON Cloud connected , APP and web could access HMI.
305
306 In HMI V2.0
307
308 * =0: Network is disconnected.
309 * =1: Network is connected.
310 )))
311 |=(% style="width: 160px;" %)HSW855|(% style="width:282px" %)Backlight Control|(% style="width:452px" %)(((
312 * HSX855.0=1: turn on the backlight and reset automatically after being triggered.
313 * HSX855.1=1: turn off the backlight and reset automatically after being triggered.
314 )))
315 |=(% style="width: 160px;" %)HSW856|(% style="width:282px" %)Whether to close the indirect screen when the current screen is switched to the other screen)|(% style="width:452px" %)(((
316 * =0: close the sub-screen, including the indirect screen;
317 * =1: not to close.
318 )))
319 |=(% style="width: 160px;" %)HSW857|(% style="width:282px" %)Permission in remote access (web page, mobile APP, cloud platform, etc.)|(% style="width:452px" %)(((
320 * =0: users could switch the screen, control the switch and update data in remote access.
321 * =1: users could only control function switch (only switch the screen), view data and switch state, but could not operate or update them.
322 * =2: users could neither operate the screen switch, nor switch operation and data modification, only view. (The ig series and 8000/9000 series with -R after system upgrade)
323 )))
324 |=(% style="width: 160px;" %)HSW860~~861|(% style="width:282px" %)Data partition remaining space|(% style="width:452px" %)Display the data partition remaining space, updated every minute, unit(**kB**)
325 |=(% style="width: 160px;" %)HSW880|(% style="width:282px" %)Enable data partition remaining space|(% style="width:452px" %)(((
326 ~=1, able to view the data partition remaining space from HSW860~~861.
327
328 ~=Other value except 1, disable the viewing function.
329 )))
330 |=(% style="width: 160px;" %)HSW881|(% style="width:282px" %)Storage of Record files|(% style="width:452px" %)(((
331 It is used for controlling saving alarm/data record files to U disk / SD card.
332
333 * = 0: Save to storage.
334 * = 1: Don't save to storage.
335 )))
336 |=(% style="width: 160px;" %)HSW882|(% style="width:282px" %)Storage device status|(% style="width:452px" %)(((
337 * HDX882.0=0 USB flash doesn't execute storage or storage finished.
338 * HDX882.0=1 USB flash is reading data, don't remove USB flash.
339 * HDX882.1=0 SD card doesn't execute storage or storage finished.
340 * HDX882.1=1 SD card is reading data, don't remove SD card.
341 )))
342 |=(% style="width: 160px;" %)HSW884|(% style="width:282px" %)Enter setup screen|(% style="width:452px" %)(((
343 * = 0: Do not into setup screen
344 * = 1: Enter setup screen
345 )))
346 |=(% style="width: 160px;" %)HSW885|(% style="width:282px" %)When the control object hides the address is read failed (communication failure), set the display mode of the object|(% style="width:452px" %)(((
347 * = 0: displayed by object setting.
348 * =1: control address read failure, the address control of all objects is hidden, not displayed.
349 * =2: control address read failure, the address control of all objects is displayed, not hidden.
350 )))
351 |=(% style="width: 160px;" %)HSW893|(% style="width:282px" %)(((
352 User Permission Control Address, same as HUW1000 feature, please refer to chapter "[[User Permission>>http://13.229.109.52:8080/wiki/pistudio/view/Helps/08.Basic%20Function/#HUserPermission]]"
353
354 **✎Note: **This address can only take effect when it is operated in the real HMI, and the operation is invalid on Web/App side.
355 )))|(% style="width:452px" %)(((
356 * =1: User Log in
357 * =2: Change User password
358 * =3: User Log out
359 * =4: New user
360 * =5: Delete user
361 * =6: Add user rights
362 * =8: Add Hide features
363 * =9: Delete Profile
364 * =10: Export Profile
365 * =11: Import profile
366 * =12: Export log file
367 * =13: Delete log file
368 )))
369 |=(% style="width: 160px;" %)HSW900|(% style="width:282px" %)Quick update frequency settings for objects|(% style="width:452px" %)(((
370 Valid when the object is enabled for "quick update". Default: 5.
371
372 Range: 1 (fastest) ~~ 50 (slowest)
373 )))
374 |=(% style="width: 160px;" %)HSW920|(% style="width:282px" %)Static mode Maximum periods|(% style="width:452px" %)Numeric Input/ Display (range: 0-12)
375 |=(% style="width: 160px;" %)HSW921 ~~ 924|(% style="width:282px" %)Static mode Admin key|(% style="width:452px" %)Character Input/ Display (length: 8)
376 |=(% style="width: 160px;" %)HSW925 ~~ 928|(% style="width:282px" %)1^^st^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
377 |=(% style="width: 160px;" %)HSW929 ~~ 933|(% style="width:282px" %)1^^st^^ expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
378 |=(% style="width: 160px;" %)HSW935 ~~ 938|(% style="width:282px" %)2^^nd^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
379 |=(% style="width: 160px;" %)HSW939 ~~ 943|(% style="width:282px" %)2^^nd ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
380 |=(% style="width: 160px;" %)HSW945 ~~ 948|(% style="width:282px" %)3^^rd^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
381 |=(% style="width: 160px;" %)HSW949 ~~ 953|(% style="width:282px" %)3^^rd ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
382 |=(% style="width: 160px;" %)HSW955 ~~ 958|(% style="width:282px" %)4^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
383 |=(% style="width: 160px;" %)HSW959 ~~ 963|(% style="width:282px" %)4^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
384 |=(% style="width: 160px;" %)HSW965 ~~ 968|(% style="width:282px" %)5^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
385 |=(% style="width: 160px;" %)HSW969 ~~ 973|(% style="width:282px" %)5^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
386 |=(% style="width: 160px;" %)HSW975 ~~ 978|(% style="width:282px" %)6^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
387 |=(% style="width: 160px;" %)HSW979 ~~ 983|(% style="width:282px" %)6^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
388 |=(% style="width: 160px;" %)HSW985 ~~ 988|(% style="width:282px" %)7^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
389 |=(% style="width: 160px;" %)HSW989 ~~ 993|(% style="width:282px" %)7^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
390 |=(% style="width: 160px;" %)HSW995 ~~ 998|(% style="width:282px" %)8^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
391 |=(% style="width: 160px;" %)HSW999 ~~ 1003|(% style="width:282px" %)8^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
392 |=(% style="width: 160px;" %)HSW1005 ~~1008|(% style="width:282px" %)9^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
393 |=(% style="width: 160px;" %)HSW1009 ~~ 1013|(% style="width:282px" %)9^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
394 |=(% style="width: 160px;" %)HSW1015 ~~1018|(% style="width:282px" %)10^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
395 |=(% style="width: 160px;" %)HSW1019 ~~ 1023|(% style="width:282px" %)10^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
396 |=(% style="width: 160px;" %)HSW1025 ~~1028|(% style="width:282px" %)11^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
397 |=(% style="width: 160px;" %)HSW1029 ~~ 1033|(% style="width:282px" %)11^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
398 |=(% style="width: 160px;" %)HSW1035 ~~1038|(% style="width:282px" %)12^^th^^ period key (Static mode)|(% style="width:452px" %)Character Input/ Display (length: 8)
399 |=(% style="width: 160px;" %)HSW1039 ~~ 1043|(% style="width:282px" %)12^^th ^^expiry time (Static mode)|(% style="width:452px" %)Numeric Input/ Display (YYYYMMDDHHMM)
400 |=(% style="width: 160px;" %)HSW1046|(% style="width:282px" %)Current period (Static mode)|(% style="width:452px" %)Current period (Range 1-13)
401 |=(% style="width: 160px;" %)HSW1047|(% style="width:282px" %)Save settings (Static mode)|(% style="width:452px" %)(((
402 * HSX1047.0=1: Save static installment information
403 * HSX1047.1=1: Write installment information to registers
404 )))
405 |=(% style="width: 160px;" %)HSW1050~~HSW1065|(% style="width:282px" %)The recipe name that can input csv format|(% style="width:452px" %)Input CSV format recipe file name through "Character Input/ Display".(This function should be used in combination with the recipefunction)
406 |=(% style="width: 160px;" %)HSW1066|(% style="width:282px" %)Configure the type of the CSV file imported|(% style="width:452px" %)(((
407 The CSV file type imported (This function should be used in combination with the recipe function)
408
409 * =0: Import customed CSV file. The data in the file is valid.
410 * =1: Import ordinary recipe files of regular series HMI. The 1st row of the file is invalid.
411 * =2: Import special recipe files of regular series HMI. The 1st and 3nd rows and the 1st colume of the file is invalid.
412 )))
413 |=(% style="width: 160px;" %)HSW1067|(% style="width:282px" %)Location where the CSV file is saved|(% style="width:452px" %)(((
414 Set the path of CSV file (This function should be used in combination with the recipe function)
415
416 * =0: In the CsvFile directory of the USB stick
417 * =1: In the CsvFile directory of the SD card
418 )))
419 |=(% style="width: 160px;" %)HSW1070|(% style="width:282px" %)The time interval (seconds) since the last time the screen was clicked|(% style="width:452px" %)(((
420 Shows how long the current screen has not been clicked, using a decimal unsigned double word (Numeric Input/ Display).
421
422 **✎Note: **This register is cleared to zero regardless of which user clicks on the screen.
423 )))
424 |=(% style="width: 160px;" %)HSW1073|(% style="width:282px" %)Corresponding key value from keyboard|(% style="width:452px" %)Display the key value of the currently pressed key, the key value is shown in Table 1 (not updated when the character input display is being input)
425 |=(% style="width: 160px;" %)HSW1074|(% style="width:282px" %)Keyboard key status|(% style="width:452px" %)Display the current button status (not updated when the numeric input display is being input)(((
426 * =0: key release
427 * =1: key press
428 * =2: Long press the button
429 )))
430 |=(% style="width: 160px;" %)HSW1075|(% style="width:282px" %)Cursor speed|(% style="width:452px" %)Control the cursor movement speed, the range is 0～100, the default is 20
431 |=(% style="width: 160px;" %)HSW1076|(% style="width:282px" %)Cursor x coordinate value|(% style="width:452px" %)Record the x value at the current position of the cursor, range: 0 to screen width -1
432 |=(% style="width: 160px;" %)HSW1077|(% style="width:282px" %)Cursor y coordinate value|(% style="width:452px" %)Record the y value at the current position of the cursor, range: 0 to screen height-1
433 |=(% style="width: 160px;" %)HSW1078|(% style="width:282px" %)Corresponding ASCII code for keyboard keys|(% style="width:452px" %)Only the ASCII value of letters, numbers, and symbols are displayed, and the ASCII value of the function button is not displayed.
434 |=(% style="width: 160px;" %)HSW1079|(% style="width:282px" %)Trigger to set the cursor position and set the Enter key mode|(% style="width:452px" %)(((
435 * HSX1079.0=1: Set the cursor position according to the cursor xy register value;
436 * HSX1079.1=0: When the numeric/character input display is being input, press Enter to end the input, no value/text part is being input, Enter is a normal click;
437 * HSX1079.1=1 Regardless of whether the numeric/character component is inputting the Enter key, only normal click is performed, and the keyboard end input is not performed.
438 )))
439 |=(% style="width: 160px;" %)HSW1083|(% style="width:282px" %)Naming method for printing object screenshots|(% style="width:452px" %)(((
440 Example: The time is 2019-01-04 14:29:10 (523 milliseconds), the screen number is 0, and the object ID is 2.
441
442 * =0: Use year, month, day, hour, minute, second, millisecond, screen number, part number to name, such as: 2019010414291052302.bmp.
443 * =1: Name using year, month, day, hour, minute, and second.
444
445 For example: 20190104142910.bmp.
446 )))
447 |=(% style="width: 160px;" %)HSW1086|(% style="width:282px" %)Control address mapping polling cycle, unit: ms|(% style="width:452px" %)(((
448 Address mapping polling cycle, effective range: 40~~1000ms, default: 300ms.
449
450 * When the set value is greater than 1000, the value is 1000.
451 * When the set value is greater than 1000, it changes to the default value 300
452 )))
453 |=(% style="width: 160px;" %)HSW1087|(% style="width:282px" %)Control write interval in address mapping|(% style="width:452px" %)(((
454 After reading data to the device for N times, Perform an address mapping write operation. N is the interval value. The effective range: 0~~5, and default is 2.
455
456 When N more than 5, it is 5.
457
458 0 is the fastest and 5 is the slowest.
459 )))
460 |=(% style="width: 160px;" %)HSW1088|(% style="width:282px" %)Control the write interval of script|(% style="width:452px" %)(((
461 After reading data to the device for N times, Perform a script write operation. N is the interval value. The effective range: 0~~5, and default is 2.
462
463 When N more than 5, it is 5.
464
465 0 is the fastest and 5 is the slowest.
466 )))
467 |=(% style="width: 160px;" %)HSW1089|(% style="width:282px" %)Control interval of read through|(% style="width:452px" %)(((
468 After reading data to the device for N times, Perform a read through operation. N is the interval value. The effective range: 0~~5, and default is 2.
469
470 When N more than 5, it is 5.
471
472 0 is the fastest and 5 is the slowest.
473 )))
474 |=(% style="width: 160px;" %)HSW1100|(% colspan="1" rowspan="4" style="width:282px" %)Set the Master IP for Multi-link|(% style="width:452px" %)High word 1 for Master IP address of multi-link
475 |=(% style="width: 160px;" %)HSW1101|(% style="width:452px" %)High word 2 for Master IP address of multi-link
476 |=(% style="width: 160px;" %)HSW1102|(% style="width:452px" %)High word 3 for Master IP address of multi-link
477 |=(% style="width: 160px;" %)HSW1103|(% style="width:452px" %)High word 4 for Master IP address of multi-link
478 |=(% style="width: 160px;" %)HSW1104|(% style="width:282px" %)Control connection to Master or not for Multi-link slave device|(% style="width:452px" %)(((
479 * =1: Connect to the Master
480 * =0: Do not connect to Master
481 )))
482 |=(% style="width: 160px;" %)HSW1141|(% style="width:282px" %)Release alarm|(% style="width:452px" %)(((
483 * =0, Default value
484 * =1, Release the alarm generated before the last power-down when starting up
485 )))
486 |=(% style="width: 160px;" %)HSW1450|(% style="width:282px" %)Enable objects level password function|(% style="width:452px" %)(((
487 * =0, Disable
488 * =1, Enable
489 )))
490 |=(% style="width: 160px;" %)HSW1451|(% style="width:282px" %)Whether the object level passwords are independent of each other|(% style="width:452px" %)(((
491 * =0, No, high-level passwords can unlock low-level
492 * = 1, Yes, high-level passwords cannot unlock low-level
493 )))
494 |=(% style="width: 160px;" %)HSW1452|(% style="width:282px" %)Initialization level|(% style="width:452px" %)Initialization level while HMI running
495 |=(% style="width: 160px;" %)HSW1454~~1457|(% style="width:282px" %)Password for Level 1|(% style="width:452px" %)(((
496 Display password for level 1, using character input object, up to 8 characters (numbers, letters (case sensitive))
497 )))
498 |=(% style="width: 160px;" %)HSW1458~~1461|(% style="width:282px" %)Password for Level 2|(% style="width:452px" %)Display password for level 2, using character input object, up to 8 characters (numbers, letters (case sensitive))
499 |=(% style="width: 160px;" %)HSW1462~~1465|(% style="width:282px" %)Password for Level 3|(% style="width:452px" %)Display password for level 3, using character input object, up to 8 characters (numbers, letters (case sensitive))
500 |=(% style="width: 160px;" %)HSW1466~~1469|(% style="width:282px" %)Password for Level 4|(% style="width:452px" %)Display password for level 4, using character input object, up to 8 characters (numbers, letters (case sensitive))
501 |=(% style="width: 160px;" %)HSW1470~~1473|(% style="width:282px" %)Password for Level 5|(% style="width:452px" %)Display password for level 5, using character input object, up to 8 characters (numbers, letters (case sensitive))
502 |=(% style="width: 160px;" %)HSW1474~~1477|(% style="width:282px" %)Password for Level 6|(% style="width:452px" %)Display password for level 6, using character input object, up to 8 characters (numbers, letters (case sensitive))
503 |=(% style="width: 160px;" %)HSW1478~~1481|(% style="width:282px" %)Password for Level 7|(% style="width:452px" %)Display password for level 7, using character input object, up to 8 characters (numbers, letters (case sensitive))
504 |=(% style="width: 160px;" %)HSW1482~~1485|(% style="width:282px" %)Password for Level 8|(% style="width:452px" %)Display password for level 8, using character input object, up to 8 characters (numbers, letters (case sensitive))
505 |=(% style="width: 160px;" %)HSW1486~~1489|(% style="width:282px" %)Password for Level 9|(% style="width:452px" %)Display password for level 9, using character input object, up to 8 characters (numbers, letters (case sensitive))
506 |=(% style="width: 160px;" %)HSW1490~~1493|(% style="width:282px" %)Password for Level 10|(% style="width:452px" %)Display password for level 10, using character input object, up to 8 characters (numbers, letters (case sensitive))
507 |=(% style="width: 160px;" %)HSW1494~~1497|(% style="width:282px" %)Password for Level 11|(% style="width:452px" %)Display password for level 11, using character input object, up to 8 characters (numbers, letters (case sensitive))
508 |=(% style="width: 160px;" %)HSW1498~~1501|(% style="width:282px" %)Password for Level 12|(% style="width:452px" %)Display password for level 12, using character input object, up to 8 characters (numbers, letters (case sensitive))
509 |=(% style="width: 160px;" %)HSW1502|(% style="width:282px" %)Modify password for object level|(% style="width:452px" %)(((
510 * HSX1502.0=1: Modification comfirmed. Save the data of HSW1450~~HSW1501 to a file for immediate effect.
511 * HSX1502.1=1:Modification cancelled. Restore the current data of hSW1450-HSW1501 to the data saved in the file last time.
512 )))
513 |=(% style="width: 160px;" %)HSW1603|(% style="width:282px" %)Number of current unreleased alarms|(% style="width:452px" %)The number of current unreleased alarms in alarm record file.
514 |=(% style="width: 160px;" %)HSW1604|(% style="width:282px" %)The auxiliary judgment address when the control bit in the Object Lock fails to be read|(% style="width:452px" %)(((
515 * =0: The auxiliary address is invalid.
516 * =1: When the communication fails, lock the object.
517 * =2: When the communication fails, unlock the object.
518 * =Others: The auxiliary address is invalid.
519 )))
520 |=(% style="width: 160px;" %)HSW1605|(% style="width:282px" %)BCD format natural decimal control|(% style="width:452px" %)(((
521 Whether to display natural decimals with decimal point in BCD format:
522
523 * 0=Not enabled.
524 * 1=Enable.
525
526 (For example, 56.20 is displayed as 56.2, 33.00 is displayed as 33)
527 )))
528 |=(% style="width: 160px;" %)HSW1606|(% style="width:282px" %)User permission modification control|(% style="width:452px" %)(((
529 * =0: Ordinary users are allowed to modify permissions and other operations
530 * =1: Only the administrator can operate (default is 0)
531 )))
532 |=(% style="width: 160px;" %)HSW1607|(% style="width:282px" %)The spacing value among the drop-down items of the drop-down list|(% style="width:452px" %)10 to 50 is effective, such as: 23 is 2.3 times the height of the object.
533 |=(% style="width: 160px;" %)HSW1611|(% style="width:282px" %)(((
534 Traditional recipe transfer
535 )))|(% style="width:452px" %)(((
536 * =1: download traditional recipe.
537 * =2: upload the traditional recipe.
538 )))
539 |=(% style="width: 160px;" %)HSW1612|(% style="width:282px" %)Traditional Recipe group number|(% style="width:452px" %)Traditional Recipe group number
540 |=(% style="width: 160px;" %)HSW1613|(% style="width:282px" %)Display the status of network card|(% style="width:452px" %)(((
541 * =1: Normal
542 * =Others: Abnormal
543 )))
544 |=(% style="width: 160px;" %)HSW1614~~1623|(% style="width:282px" %)Download speed per second|(% style="width:452px" %)Display the download speed per second. (The value is string)
545 |=(% style="width: 160px;" %)HSW1624~~1633|(% style="width:282px" %)Upnload speed per second|(% style="width:452px" %)Display the upload speed per second. (The value is string)
546 |=(% style="width: 160px;" %)HSW1634~~1643|(% style="width:282px" %)Flow consumption rate|(% style="width:452px" %)Display the total flow rate per second (The value is string)
547 |=(% style="width: 160px;" %)HSW1644~~1653|(% style="width:282px" %)Download flow consumption after power on|(% style="width:452px" %)Display the download flow consumption after power on (The value is string)
548 |=(% style="width: 160px;" %)HSW1654~~1663|(% style="width:282px" %)Upload flow consumption after power on|(% style="width:452px" %)Display the upload flow consumption after power on (The value is string)
549 |=(% style="width: 160px;" %)HSW1664~~1673|(% style="width:282px" %)Total flow consumption after power on|(% style="width:452px" %)Display the total flow consumption after power on (download and upload). (The value is string)
550 |=(% style="width: 160px;" %)HSW1674~~1683|(% style="width:282px" %)Historical flow consumption|(% style="width:452px" %)Display historical flow consumption (download and upload). (The value is string)
551 |=(% style="width: 160px;" %)HSW1684~~1693|(% style="width:282px" %)Flow consumption in 10 minutes|(% style="width:452px" %)Flow consumption in 10 minutes (download and upload). (The value is string)
552 |=(% style="width: 160px;" %)HSW1694~~1703|(% style="width:282px" %)Flow consumption in 30 minutes|(% style="width:452px" %)Flow consumption in 30 minutes (download and upload). (The value is string)
553 |=(% style="width: 160px;" %)HSW1704~~1713|(% style="width:282px" %)Flow consumption in 3 hours|(% style="width:452px" %)Flow consumption in 3 hours (download and upload). (The value is string)
554 |=(% style="width: 160px;" %)HSW1715|(% style="width:282px" %)Reset flow|(% style="width:452px" %)(((
555 * =1: Clear historical flow data and restart the count.
556 * =Others: Invalid
557 )))
558 |=(% style="width: 160px;" %)HSW1719|(% style="width:282px" %)Network status of Ethernet connnecting to server|(% style="width:452px" %)(((
559 * =0: Server connection exception
560 * =1: Server connection is OK
561 )))
562 |=(% style="width: 160px;" %)HSW1720|(% colspan="1" rowspan="12" style="width:282px" %)Related IP register in WIFI network status (It is valid when HMI is connected to WIFI)|(% style="width:452px" %)Local IP address high byte 1
563 |=(% style="width: 160px;" %)HSW1721|(% style="width:452px" %)Local IP address high byte 2
564 |=(% style="width: 160px;" %)HSW1722|(% style="width:452px" %)Local IP address high byte 3
565 |=(% style="width: 160px;" %)HSW1723|(% style="width:452px" %)Local IP address high byte 4
566 |=(% style="width: 160px;" %)HSW1724|(% style="width:452px" %)Local mask IP address high byte 1
567 |=(% style="width: 160px;" %)HSW1725|(% style="width:452px" %)Local mask IP address high byte 2
568 |=(% style="width: 160px;" %)HSW1726|(% style="width:452px" %)Local mask IP address high byte 3
569 |=(% style="width: 160px;" %)HSW1727|(% style="width:452px" %)Local mask IP address high byte 4
570 |=(% style="width: 160px;" %)HSW1728|(% style="width:452px" %)Local gateway IP address high byte 1
571 |=(% style="width: 160px;" %)HSW1729|(% style="width:452px" %)Local gateway IP address high byte 2
572 |=(% style="width: 160px;" %)HSW1730|(% style="width:452px" %)Local gateway IP address high byte 3
573 |=(% style="width: 160px;" %)HSW1731|(% style="width:452px" %)Local gateway IP address high byte 4
574 |=(% style="width: 160px;" %)HSW1733|(% colspan="1" rowspan="6" style="width:282px" %)(((
575 Display the MAC code of current WIFI
576
577 (display in hexadecimal)
578 )))|(% style="width:452px" %)Local MAC address high byte 1 (hexadecimal)
579 |=(% style="width: 160px;" %)HSW1734|(% style="width:452px" %)Local MAC address high byte 2 (hexadecimal)
580 |=(% style="width: 160px;" %)HSW1735|(% style="width:452px" %)Local MAC address high byte 3 (hexadecimal)
581 |=(% style="width: 160px;" %)HSW1736|(% style="width:452px" %)Local MAC address high byte 4 (hexadecimal)
582 |=(% style="width: 160px;" %)HSW1737|(% style="width:452px" %)Local MAC address high byte 5 (hexadecimal)
583 |=(% style="width: 160px;" %)HSW1738|(% style="width:452px" %)Local MAC address high byte 6 (hexadecimal)
584 |=(% style="width: 160px;" %)HSW1739|(% style="width:282px" %)Display the network status of WIFI|(% style="width:452px" %)(((
585 * =0: Server connection exception
586 * =1: Server connection is OK
587 )))
588 |=(% style="width: 160px;" %)HSW1741|(% colspan="1" rowspan="12" style="width:282px" %)Related IP register in 4Gnetwork status (It is valid when HMI is connected to 4G)|(% style="width:452px" %)Local IP address high byte 1
589 |=(% style="width: 160px;" %)HSW1742|(% style="width:452px" %)Local IP address high byte 2
590 |=(% style="width: 160px;" %)HSW1743|(% style="width:452px" %)Local IP address high byte 3
591 |=(% style="width: 160px;" %)HSW1744|(% style="width:452px" %)Local IP address high byte 4
592 |=(% style="width: 160px;" %)HSW1745|(% style="width:452px" %)Local mask IP address high byte 1
593 |=(% style="width: 160px;" %)HSW1746|(% style="width:452px" %)Local mask IP address high byte 2
594 |=(% style="width: 160px;" %)HSW1747|(% style="width:452px" %)Local mask IP address high byte 3
595 |=(% style="width: 160px;" %)HSW1748|(% style="width:452px" %)Local mask IP address high byte 4
596 |=(% style="width: 160px;" %)HSW1749|(% style="width:452px" %)Local gateway IP address high byte 1
597 |=(% style="width: 160px;" %)HSW1750|(% style="width:452px" %)Local gateway IP address high byte 2
598 |=(% style="width: 160px;" %)HSW1751|(% style="width:452px" %)Local gateway IP address high byte 3
599 |=(% style="width: 160px;" %)HSW1752|(% style="width:452px" %)Local gateway IP address high byte 4
600 |=(% style="width: 160px;" %)HSW1754|(% colspan="1" rowspan="6" style="width:282px" %)(((
601 Display the MAC code of current WIFI
602
603 (display in hexadecimal)
604 )))|(% style="width:452px" %)Local MAC address high byte 1 (hexadecimal)
605 |=(% style="width: 160px;" %)HSW1755|(% style="width:452px" %)Local MAC address high byte 2 (hexadecimal)
606 |=(% style="width: 160px;" %)HSW1756|(% style="width:452px" %)Local MAC address high byte 3 (hexadecimal)
607 |=(% style="width: 160px;" %)HSW1757|(% style="width:452px" %)Local MAC address high byte 4 (hexadecimal)
608 |=(% style="width: 160px;" %)HSW1758|(% style="width:452px" %)Local MAC address high byte 5 (hexadecimal)
609 |=(% style="width: 160px;" %)HSW1759|(% style="width:452px" %)Local MAC address high byte 6 (hexadecimal)
610 |=(% style="width: 160px;" %)HSW1760|(% style="width:282px" %)Display 4G network status|(% style="width:452px" %)(((
611 * =0: Server connection exception
612 * =1: Server connection is OK
613 )))
614 |=(% style="width: 160px;" %)HSW1761|(% style="width:282px" %)Display 4G network signal strength|(% style="width:452px" %)Signal strength: 0~~31. The greater the value ,the signal is stronger
615 |=(% style="width: 160px;" %)HSW1852|(% style="width:282px" %)Control the interval in two consecutive clicks|(% style="width:452px" %)Limit range: 1~~500ms. The default is 100 ms.
616 |=(% style="width: 160px;" %)HSW1853|(% style="width:282px" %)File format for exporting data records to USB flash drive or SD card|(% style="width:452px" %)(((
617 * =0: db database
618 * =1: CSV
619 )))
620 |=(% style="width: 160px;" %)HSW1854|(% style="width:282px" %)High and low word conversion type|(% style="width:452px" %)(((
621 * =0: use the old high-low word conversion (default)
622 * =1: usie the new high-low word conversion
623 )))
624 |=(% style="width: 160px;" %)HSW1855|(% style="width:282px" %)Screen Lock prompt display control|(% style="width:452px" %)(((
625 Control whether the screen lock prompt is displayed,
626
627 * =0: display(default value)
628 * =Other: no display.
629 )))
630 |=(% style="width: 160px;" %)HSW1856|(% style="width:282px" %)Display map fence drawing status|(% style="width:452px" %)(((
631 * =0: no map fence
632 * =1: The map fence is drawn and the device is inside the fence
633 * =2: The map fence is drawn and the device is outside the fence
634 )))
635 |=(% style="width: 160px;" %)HSW1857|(% style="width:282px" %)USB disk download |(% style="width:452px" %)(((
636 * =0: download project
637 * =1: download firmware
638 * =2: enter the background
639 )))
640 |=(% style="width: 160px;" %)HSW10000~~19999|(% style="width:282px" %)Power-down storage area|(% style="width:452px" %)After restart, the data remains
641 |=(% style="width: 160px;" %)HSW10035|(% rowspan="13" style="width:282px" %)(((
642 **✎Note: **Only valid when the HMI is plugged into the Ethernet cable.
643
644 1. If Ethernet settings is enabled in project parameters, this register displays the set value.
645 1. If Ethernet settings is not enabled in project parameters, IP would automatically obtained IP.
646 1. If HMI is not connected to the network, the register is displayed as 0 whether the engineering parameters are set.
647 1. 4. All IP registers of HMI are read-only.
648 )))|(% style="width:452px" %)Local IP address high byte 1
649 |=(% style="width: 160px;" %)HSW10036|(% style="width:452px" %)Local IP address high byte 2
650 |=(% style="width: 160px;" %)HSW10037|(% style="width:452px" %)Local IP address high byte 3
651 |=(% style="width: 160px;" %)HSW10038|(% style="width:452px" %)Local IP address high byte 4
652 |=(% style="width: 160px;" %)HSW10039|(% style="width:452px" %)Local mask IP address high byte 1
653 |=(% style="width: 160px;" %)HSW10040|(% style="width:452px" %)Local mask IP address high byte 2
654 |=(% style="width: 160px;" %)HSW10041|(% style="width:452px" %)Local mask IP address high byte 3
655 |=(% style="width: 160px;" %)HSW10042|(% style="width:452px" %)Local mask IP address high byte 4
656 |=(% style="width: 160px;" %)HSW10043|(% style="width:452px" %)Local gateway address high byte 1
657 |=(% style="width: 160px;" %)HSW10044|(% style="width:452px" %)Local gateway address high byte 2
658 |=(% style="width: 160px;" %)HSW10045|(% style="width:452px" %)Local gateway address high byte 3
659 |=(% style="width: 160px;" %)HSW10046|(% style="width:452px" %)Local gateway address high byte 4
660 |=(% style="width: 160px;" %)HSW10047|(% style="width:452px" %)Local port address
661 |=(% style="width: 160px;" %)HSW10048|(% rowspan="6" style="width:282px" %)(((
662 Displays the MAC code of the current network card
663
664 (Hexadecimal display)
665 )))|(% style="width:452px" %)Local MAC code high word 1
666 |=(% style="width: 160px;" %)HSW10049|(% style="width:452px" %)Local MAC code high word 2
667 |=(% style="width: 160px;" %)HSW10050|(% style="width:452px" %)Local MAC code high word 3
668 |=(% style="width: 160px;" %)HSW10051|(% style="width:452px" %)Local MAC code high word 4
669 |=(% style="width: 160px;" %)HSW10052|(% style="width:452px" %)Local MAC code high word 5
670 |=(% style="width: 160px;" %)HSW10053|(% style="width:452px" %)Local MAC code high word 6
671 |=(% style="width: 160px;" %)HSW10118|(% colspan="1" rowspan="2" style="width:282px" %)TSAP settings for HMI in the Siemens logo! 8 protocol|(% style="width:452px" %)HMI local TSAP, which corresponds to the remote TSAP of PLC
672 |=(% style="width: 160px;" %)HSW10119|(% style="width:452px" %)HMI remote TSAP, which corresponds to the local TSAP of PLC
673 |=(% style="width: 160px;" %)HSW10461~~10493|(% style="width:282px" %)Remote access password|(% style="width:452px" %)8-character remote access password
674 |=(% style="width: 160px;" %)HSW10494~~10558|(% style="width:282px" %)Machine ID (Read only)|(% style="width:452px" %)Machine ID for remote access (read only 64-bit)
675 |=(% style="width: 160px;" %)HSW10576|(% style="width:282px" %)Save dynamic installment settings|(% style="width:452px" %)HSX10576.0=1: Save the set dynamic installment information
676 |=(% style="width: 160px;" %)HSW10577|(% style="width:282px" %)Control address for installment|(% style="width:452px" %)(((
677 * HSX10577.0=0: disable dynamic installment
678 * HSX10577.0=1: enable dynamic installment
679 * HSX10577.1=0: disable static installment
680 * HSX10577.1=1: enable static installment
681 )))
682 |=(% style="width: 160px;" %)HSW10578-10583|(% style="width:282px" %)Password for dynamic installment|(% style="width:452px" %)Character Input/ Display (length: 6)
683 |=(% style="width: 160px;" %)HSW10584-10586|(% style="width:282px" %)Expiry time of dynamic installment|(% style="width:452px" %)Expiry time: YYYYMMDD (Numeric Input/ Display)
684 |=(% style="width: 160px;" %)HSW10587-10589|(% style="width:282px" %)Last expiry time of dynamic installment|(% style="width:452px" %)Expiry time: YYYYMMDD (Numeric Input/ Display)
685 |=(% style="width: 160px;" %)HSW10590|(% style="width:282px" %)Background light time|(% style="width:452px" %)(((
686 Set the light time for background
687
688 * =0: The screen backlight is always on.
689 * =Others: The screen backlight is on for a period of time and then turns off. The length of time is controlled by the value of the register address. Unit: second.
690 )))
691 |=(% style="width: 160px;" %)HSW10591|(% style="width:282px" %)Backlight brightness adjustment|(% style="width:452px" %)Backlight brightness range: 1 (darkest) ~~ 100 (brightest)
692 |=(% style="width: 160px;" %)HSW10603|(% style="width:282px" %)Set the printer to print orientation|(% style="width:452px" %)(((
693 Set the print direction:
694
695 * =1: Forward printing
696 * =2: Reverse print
697 * =Other: Forward print
698 )))
699 |=(% style="width: 160px;" %)HSW10604|(% style="width:282px" %)Print dot type|(% style="width:452px" %)(((
700 * =1: new firmware 8 dot matrix type
701 * =2: new firmware 24 dot matrix type
702 * =3: old firmware 8 dot matrix type
703 * =4: old firmware 24 dot matrix type
704 * =Other: new firmware 8 dot matrix type
705 )))
706 |=(% style="width: 160px;" %)HSW10605|(% style="width:282px" %)Print width of printer|(% style="width:452px" %)Set the width of the printer to print (in pixels), such as HSW10605 = 394: The printer supports images with a print width of 394 pixels
707 |=(% style="width: 160px;" %)HSW10606|(% style="width:282px" %)Printer instruction type|(% style="width:452px" %)(((
708 * =1: Graphic print type
709 * =2: Dot density printing type
710 * =3: special for EPSON printer
711 )))
712 |=(% style="width: 160px;" %)HSW10607|(% style="width:282px" %)Printer paper cutting function|(% style="width:452px" %)(((
713 * =1: Enable
714 * =2: Disable
715 )))
716 |=(% style="width: 160px;" %)HSW10608|(% style="width:282px" %)Print the alignment of the text|(% style="width:452px" %)(((
717 * =1: Left alignment
718 * =2: Center alignment
719 * =3: Right alignment
720 )))
721 |=(% style="width: 160px;" %)HSW10610|(% style="width:282px" %)Set weconcloud server|(% style="width:452px" %)(((
722 * =0: Select the server configured in "Project Settings"
723 * =1: select Server 1
724 * =2: select Server 2
725 )))
726 |=(% style="width: 160px;" %)HSW11750|(% style="width:282px" %)Set the language of the Message List prompt** (ie series)**|(% style="width:452px" %)(((
727 * =0: which is followed the project language
728 * =1: English
729 * =2: Chinese
730 )))
731 |=(% style="width: 160px;" %)HSW11756|(% style="width:282px" %)(((
732 Access permission restrictions
733
734 (ig series and** **8000/9000 series with -R after system upgrade)
735 )))|(% style="width:452px" %)(((
736 * =0: LAN or the external network both OK
737 * =1: Only LAN access
738 * =2: Only external network can access
739 )))
740 |=(% style="width: 160px;" %)HSW11757|(% style="width:282px" %)Enable the valid date of the dynamic installment password|(% style="width:452px" %)(((
741 * =0: Disabled
742 * =1: Enable
743 )))
744 |=(% style="width: 160px;" %)HSW11758|(% style="width:282px" %)Enable Screensaver|(% style="width:452px" %)(((
745 * =0: Disabled
746 * =1: Enable
747 )))
748 |=(% style="width: 160px;" %)HSW11759|(% style="width:282px" %)Screensaver interval time|(% style="width:452px" %)(((
749 Set the time how long will enter Screensaver (Range 10~~43200s)
750 )))
751 |=(% style="width: 160px;" %)HSW11760|(% style="width:282px" %)Screensaver countdown|(% style="width:452px" %)Display the countdown to enter the Screensaver, unit: second.
752 |=(% style="width: 160px;" %)HSW11761|(% style="width:282px" %)Screensaver screen number|(% style="width:452px" %)Set the screen number for Screensaver
753
754 == **Serial port communication configuration** ==
755
756 (% class="table-bordered" %)
757 |=(% style="width: 102px;" %)Port|=(% style="width: 173px;" %)**Function**|=(% style="width: 122px;" %)**Address**|=(% colspan="2" style="width: 506px;" %)**Description**
758 |(% colspan="1" rowspan="11" style="width:102px" %)COM1|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10061|(% colspan="2" style="width:506px" %)(((
759 * =0: RS232
760 * =1: RS485
761 * =2: RS422
762 )))
763 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10062|(% colspan="2" style="width:506px" %)(((
764 * =0: 1200
765 * =1: 2400
766 * =2: 4800
767 * =3: 9600
768 * =4: 19200
769 * =5: 38400
770 * =6: 57600
771 * =7: 115200
772 * =8: 230400
773 )))
774 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10063|(% colspan="2" style="width:506px" %)(((
775 * =7: 7 bit
776 * =8: 8 bit
777 )))
778 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10064|(% colspan="2" style="width:506px" %)(((
779 * =1: 1 bit
780 * =2: 2 bit
781 )))
782 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10065|(% colspan="2" style="width:506px" %)(((
783 * =0: None
784 * =1: ODD
785 * =2: EVEN
786 )))
787 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10066|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
788 |(% style="width:173px" %)reveive timeout|(% style="width:122px" %)HSW10067|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
789 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10068|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
790 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10069|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~300
791 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10070|(% colspan="2" style="width:506px" %)
792 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10071|(% colspan="2" style="width:506px" %)
793 |(% colspan="1" rowspan="11" style="width:102px" %)COM1-2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10094|(% colspan="2" style="width:506px" %)(((
794 * =0: RS232
795 * =1: RS485
796 * =2: RS422
797 * =6: RS485-2
798 )))
799 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10095|(% colspan="2" style="width:506px" %)(((
800 * =0: 1200
801 * =1: 2400
802 * =2: 4800
803 * =3: 9600
804 * =4: 19200
805 * =5: 38400
806 * =6: 57600
807 * =7: 115200
808 * =8: 230400
809 )))
810 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10096|(% colspan="2" style="width:506px" %)(((
811 * =7: 7 bit
812 * =8: 8 bit
813 )))
814 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10097|(% colspan="2" style="width:506px" %)(((
815 * =1: 1 bit
816 * =2: 2 bit
817 )))
818 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10098|(% colspan="2" style="width:506px" %)(((
819 * =0: None
820 * =1: ODD
821 * =2: EVEN
822 )))
823 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10099|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
824 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10100|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
825 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10101|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
826 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10102|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
827 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10103|(% colspan="2" style="width:506px" %)
828 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10104|(% colspan="2" style="width:506px" %)
829 |(% colspan="1" rowspan="11" style="width:102px" %)COM1-3|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10120|(% colspan="2" style="width:506px" %)(((
830 * =0: RS232
831 * =1: RS485
832 * =2: RS422
833 * =6: RS485-2
834 )))
835 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10121|(% colspan="2" style="width:506px" %)(((
836 * =0: 1200
837 * =1: 2400
838 * =2: 4800
839 * =3: 9600
840 * =4: 19200
841 * =5: 38400
842 * =6: 57600
843 * =7: 115200
844 * =8: 230400
845 )))
846 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10122|(% colspan="2" style="width:506px" %)(((
847 * =7: 7 bit
848 * =8: 8 bit
849 )))
850 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10123|(% colspan="2" style="width:506px" %)(((
851 * =1: 1 bit
852 * =2: 2 bit
853 )))
854 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10124|(% colspan="2" style="width:506px" %)(((
855 * =0: None
856 * =1: ODD
857 * =2: EVEN
858 )))
859 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10125|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
860 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10126|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
861 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10127|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
862 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10128|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
863 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10129|(% colspan="2" style="width:506px" %)
864 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10130|(% colspan="2" style="width:506px" %)
865 |(% colspan="1" rowspan="11" style="width:102px" %)COM2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10072|(% colspan="2" style="width:506px" %)(((
866 * =0: RS232
867 * =1: RS485
868 )))
869 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10073|(% colspan="2" style="width:506px" %)(((
870 * =0: 1200
871 * =1: 2400
872 * =2: 4800
873 * =3: 9600
874 * =4: 19200
875 * =5: 38400
876 * =6: 57600
877 * =7: 115200
878 * =8: 230400
879 )))
880 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10074|(% colspan="2" style="width:506px" %)(((
881 * =7: 7 bit
882 * =8: 8 bit
883 )))
884 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10075|(% colspan="2" style="width:506px" %)(((
885 * =1: 1 bit
886 * =2: 2 bit
887 )))
888 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10076|(% colspan="2" style="width:506px" %)(((
889 * =0: None
890 * =1: ODD
891 * =2: EVEN
892 )))
893 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10077|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
894 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10078|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
895 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10079|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
896 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10080|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
897 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10081|(% colspan="2" style="width:506px" %)
898 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10082|(% colspan="2" style="width:506px" %)
899 |(% colspan="1" rowspan="11" style="width:102px" %)COM2-2|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10105|(% colspan="2" style="width:506px" %)(((
900 * =0: RS232
901 * =1: RS485
902 )))
903 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10106|(% colspan="2" style="width:506px" %)(((
904 * =0: 1200
905 * =1: 2400
906 * =2: 4800
907 * =3: 9600
908 * =4: 19200
909 * =5: 38400
910 * =6: 57600
911 * =7: 115200
912 * =8: 230400
913 )))
914 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10107|(% colspan="2" style="width:506px" %)(((
915 * =7: 7 bit
916 * =8: 8 bit
917 )))
918 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10108|(% colspan="2" style="width:506px" %)(((
919 * =1: 1 bit
920 * =2: 2 bit
921 )))
922 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10109|(% colspan="2" style="width:506px" %)(((
923 * =0: None
924 * =1: ODD
925 * =2: EVEN
926 )))
927 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10110|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
928 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10111|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
929 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10112|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
930 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10113|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
931 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10114|(% colspan="2" style="width:506px" %)
932 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10115|(% colspan="2" style="width:506px" %)
933 |(% colspan="1" rowspan="11" style="width:102px" %)COM3|(% style="width:173px" %)Communication mode|(% style="width:122px" %)HSW10083|(% colspan="2" style="width:506px" %)(((
934 * =1: RS485
935 )))
936 |(% style="width:173px" %)Baud rate|(% style="width:122px" %)HSW10084|(% colspan="2" style="width:506px" %)(((
937 * =0: 1200
938 * =1: 2400
939 * =2: 4800
940 * =3: 9600
941 * =4: 19200
942 * =5: 38400
943 * =6: 57600
944 * =7: 115200
945 * =8: 230400
946 )))
947 |(% style="width:173px" %)Data bit|(% style="width:122px" %)HSW10085|(% colspan="2" style="width:506px" %)(((
948 * =7: 7 bit
949 * =8: 8 bit
950 )))
951 |(% style="width:173px" %)Stop bit|(% style="width:122px" %)HSW10086|(% colspan="2" style="width:506px" %)(((
952 * =1: 1 bit
953 * =2: 2 bit
954 )))
955 |(% style="width:173px" %)Check bit|(% style="width:122px" %)HSW10087|(% colspan="2" style="width:506px" %)(((
956 * =0: None
957 * =1: ODD
958 * =2: EVEN
959 )))
960 |(% style="width:173px" %)Wait timeout|(% style="width:122px" %)HSW10088|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
961 |(% style="width:173px" %)receive timeout|(% style="width:122px" %)HSW10089|(% colspan="2" style="width:506px" %)Unit: ms. Range: 0~~30000
962 |(% style="width:173px" %)Retry time|(% style="width:122px" %)HSW10090|(% colspan="2" style="width:506px" %)Unit: times. Range: 0~~100
963 |(% style="width:173px" %)Retry timeout|(% style="width:122px" %)HSW10091|(% colspan="2" style="width:506px" %)Unit: s. Range: 0~~30
964 |(% style="width:173px" %)HMI station number|(% style="width:122px" %)HSW10092|(% colspan="2" style="width:506px" %)
965 |(% style="width:173px" %)PLC station number|(% style="width:122px" %)HSW10093|(% colspan="2" style="width:506px" %)
966 |(% colspan="1" rowspan="2" style="width:102px" %)CAN port|(% style="width:173px" %)CAN1 baud rate|(% style="width:122px" %)HSW010116|(% style="width:299px" %)(((
967 Unit: K, the baud rate must be an integer, for example, when the baud rate required is 250000, just enter 250.
968 )))|(% colspan="1" rowspan="2" style="width:218px" %)**✎Note: **If baud rate has been modified,please wait 5 seconds,then restart the HMI to take effect.
969 |(% style="width:173px" %)CAN2 baud rate|(% style="width:122px" %)HSW010117|(% style="width:299px" %)Unit: K, the baud rate must be an integer, for example, when the baud rate required is 250000, just enter 250.
970
971 == **Ethernet communication configuration** ==
972
973 (% class="table-bordered" %)
974 |=(% style="width: 40px;" %)**No.**|=(% style="width: 295px;" %)**Function**|=(% style="width: 220px;" %)**Address**|=(% style="width: 336px;" %)**Description**
975 |(% rowspan="7" style="width:40px" %)1|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 1 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11004|(% style="width:336px" %)Device IP address high word 1
976 |(% style="width:220px" %)HSW11005|(% style="width:336px" %)Device IP address high word 2
977 |(% style="width:220px" %)HSW11006|(% style="width:336px" %)Device IP address high word 3
978 |(% style="width:220px" %)HSW11007|(% style="width:336px" %)Device IP address high word 4
979 |(% style="width:220px" %)HSW11008|(% style="width:336px" %)Device Port number
980 |(% style="width:220px" %)HSW11009|=(% style="width: 336px;" %)(((
981 * =2 TCP
982 * =3 UDP
983 )))
984 |(% style="width:220px" %)HSW11010|(% style="width:336px" %)Reserved
985 |(% rowspan="7" style="width:40px" %)2|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 2 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11011|(% style="width:336px" %)Device IP address high word 1
986 |(% style="width:220px" %)HSW11012|(% style="width:336px" %)Device IP address high word 2
987 |(% style="width:220px" %)HSW11013|(% style="width:336px" %)Device IP address high word 3
988 |(% style="width:220px" %)HSW11014|(% style="width:336px" %)Device IP address high word 4
989 |(% style="width:220px" %)HSW11015|(% style="width:336px" %)Device Port number
990 |(% style="width:220px" %)HSW11016|=(% style="width: 336px;" %)(((
991 * =2 TCP
992 * =3 UDP
993 )))
994 |(% style="width:220px" %)HSW11017|(% style="width:336px" %)Reserved
995 |(% style="width:40px" %)…|(% style="width:295px" %) |(% style="width:220px" %)…|(% style="width:336px" %)…
996 |(% rowspan="7" style="width:40px" %)32|(% colspan="1" rowspan="7" style="width:295px" %)Ethernet parameter configuration for communication number 32 in list. Configure those addresses according to connected device. After configuration, wait for 5 seconds and restart the HMI.|(% style="width:220px" %)HSW11221|(% style="width:336px" %)Device IP address high word 1
997 |(% style="width:220px" %)HSW11222|(% style="width:336px" %)Device IP address high word 2
998 |(% style="width:220px" %)HSW11223|(% style="width:336px" %)Device IP address high word 3
999 |(% style="width:220px" %)HSW11224|(% style="width:336px" %)Device IP address high word 4
1000 |(% style="width:220px" %)HSW11225|(% style="width:336px" %)Device Port number
1001 |(% style="width:220px" %)HSW11226|=(% style="width: 336px;" %)2 TCP; =3 UDP
1002 |(% style="width:220px" %)HSW11227|(% style="width:336px" %)Reserved
1003
1004 (% class="box infomessage" %)
1005 (((
1006 **✎Note:** The number of Ethernet connections supported by different HMI series varies.
1007 )))
1008
1009 == **Communication control** ==
1010
1011 (% class="table-bordered" %)
1012 |(% style="width:135px" %)**Communication No.**|(% style="width:102px" %)**Station No.**|(% style="width:185px" %)**Control bit**|(% style="width:191px" %)**Communication lamp**|(% style="width:271px" %)**Description**
1013 |(% colspan="1" rowspan="16" style="width:135px" %)1|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX550.0～HSX550.15|(% style="width:191px" %)HSX558.0～HSX558.15|(% rowspan="160" style="width:271px" %)Communication number refers to the number in "Communication Port Configuration". A number provides 256 device station numbers. Each station number corresponds to a communication control bit and a communication indicator bit. Registers HSX550.0 to HSX805.15 are used to control the station numbers from 0 to 127, and registers HSX1150.0 to HSX1405.15 are used to control station numbers 128 to 255.
1014 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX551.0～HSX551.15|(% style="width:191px" %)HSX559.0～HSX559.15
1015 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX552.0～HSX552.15|(% style="width:191px" %)HSX560.0～HSX560.15
1016 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX553.0～HSX553.15|(% style="width:191px" %)HSX561.0～HSX561.15
1017 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX554.0～HSX554.15|(% style="width:191px" %)HSX562.0～HSX562.15
1018 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX555.0～HSX555.15|(% style="width:191px" %)HSX563.0～HSX563.15
1019 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX556.0～HSX556.15|(% style="width:191px" %)HSX564.0～HSX564.15
1020 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX557.0～HSX557.15|(% style="width:191px" %)HSX565.0～HSX565.15
1021 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1150.0～HSX1150.15|(% style="width:191px" %)HSX1158.0～HSX1158.15
1022 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1151.0～HSX1151.15|(% style="width:191px" %)HSX1159.0～HSX1159.15
1023 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1152.0～HSX1152.15|(% style="width:191px" %)HSX1160.0～HSX1160.15
1024 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1153.0～HSX1153.15|(% style="width:191px" %)HSX1161.0～HSX1161.15
1025 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1154.0～HSX1154.15|(% style="width:191px" %)HSX1162.0～HSX1162.15
1026 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1155.0～HSX1155.15|(% style="width:191px" %)HSX1163.0～HSX1163.15
1027 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1156.0～HSX1156.15|(% style="width:191px" %)HSX1164.0～HSX1164.15
1028 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1157.0～HSX1157.15|(% style="width:191px" %)HSX1165.0～HSX1165.15
1029 |(% colspan="1" rowspan="16" style="width:135px" %)2|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX566.0～HSX566.15|(% style="width:191px" %)HSX574.0～HSX574.15
1030 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX567.0～HSX567.15|(% style="width:191px" %)HSX575.0～HSX575.15
1031 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX568.0～HSX568.15|(% style="width:191px" %)HSX576.0～HSX576.15
1032 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX569.0～HSX569.15|(% style="width:191px" %)HSX577.0～HSX577.15
1033 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX570.0～HSX570.15|(% style="width:191px" %)HSX578.0～HSX578.15
1034 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX571.0～HSX571.15|(% style="width:191px" %)HSX579.0～HSX579.15
1035 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX572.0～HSX572.15|(% style="width:191px" %)HSX580.0～HSX580.15
1036 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX573.0～HSX573.15|(% style="width:191px" %)HSX581.0～HSX581.15
1037 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1166.0～HSX1166.15|(% style="width:191px" %)HSX1174.0～HSX1174.15
1038 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1167.0～HSX1167.15|(% style="width:191px" %)HSX1175.0～HSX1175.15
1039 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1168.0～HSX1168.15|(% style="width:191px" %)HSX1176.0～HSX1176.15
1040 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1169.0～HSX1169.15|(% style="width:191px" %)HSX1177.0～HSX1177.15
1041 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1170.0～HSX1170.15|(% style="width:191px" %)HSX1178.0～HSX1178.15
1042 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1171.0～HSX1171.15|(% style="width:191px" %)HSX1179.0～HSX1179.15
1043 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1172.0～HSX1172.15|(% style="width:191px" %)HSX1180.0～HSX1180.15
1044 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1173.0～HSX1173.15|(% style="width:191px" %)HSX1181.0～HSX1181.15
1045 |(% colspan="1" rowspan="16" style="width:135px" %)3|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX582.0～HSX582.15|(% style="width:191px" %)HSX590.0～HSX590.15
1046 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX583.0～HSX583.15|(% style="width:191px" %)HSX591.0～HSX591.15
1047 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX584.0～HSX584.15|(% style="width:191px" %)HSX592.0～HSX592.15
1048 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX585.0～HSX585.15|(% style="width:191px" %)HSX593.0～HSX593.15
1049 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX586.0～HSX586.15|(% style="width:191px" %)HSX594.0～HSX594.15
1050 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX587.0～HSX587.15|(% style="width:191px" %)HSX595.0～HSX595.15
1051 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX588.0～HSX588.15|(% style="width:191px" %)HSX596.0～HSX596.15
1052 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX589.0～HSX589.15|(% style="width:191px" %)HSX597.0～HSX597.15
1053 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1182.0～HSX1182.15|(% style="width:191px" %)HSX1190.0～HSX1190.15
1054 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1183.0～HSX1183.15|(% style="width:191px" %)HSX1191.0～HSX1191.15
1055 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1184.0～HSX1184.15|(% style="width:191px" %)HSX1192.0～HSX1192.15
1056 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1185.0～HSX1185.15|(% style="width:191px" %)HSX1193.0～HSX1193.15
1057 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1186.0～HSX1186.15|(% style="width:191px" %)HSX1194.0～HSX1194.15
1058 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1187.0～HSX1187.15|(% style="width:191px" %)HSX1195.0～HSX1195.15
1059 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1188.0～HSX1188.15|(% style="width:191px" %)HSX1196.0～HSX1196.15
1060 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1189.0～HSX1189.15|(% style="width:191px" %)HSX1197.0～HSX1197.15
1061 |(% colspan="1" rowspan="16" style="width:135px" %)4|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX598.0～HSX598.15|(% style="width:191px" %)HSX606.0～HSX606.15
1062 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX599.0～HSX599.15|(% style="width:191px" %)HSX607.0～HSX607.15
1063 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX600.0～HSX600.15|(% style="width:191px" %)HSX608.0～HSX608.15
1064 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX601.0～HSX601.15|(% style="width:191px" %)HSX609.0～HSX609.15
1065 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX602.0～HSX602.15|(% style="width:191px" %)HSX610.0～HSX610.15
1066 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX603.0～HSX603.15|(% style="width:191px" %)HSX611.0～HSX611.15
1067 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX604.0～HSX604.15|(% style="width:191px" %)HSX612.0～HSX612.15
1068 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX605.0～HSX605.15|(% style="width:191px" %)HSX613.0～HSX613.15
1069 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1198.0～HSX1198.15|(% style="width:191px" %)HSX1206.0～HSX1206.15
1070 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1199.0～HSX1199.15|(% style="width:191px" %)HSX1207.0～HSX1207.15
1071 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1200.0～HSX1200.15|(% style="width:191px" %)HSX1208.0～HSX1208.15
1072 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1201.0～HSX1201.15|(% style="width:191px" %)HSX1209.0～HSX1209.15
1073 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1202.0～HSX1202.15|(% style="width:191px" %)HSX1210.0～HSX1210.15
1074 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1203.0～HSX1203.15|(% style="width:191px" %)HSX1211.0～HSX1211.15
1075 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1204.0～HSX1204.15|(% style="width:191px" %)HSX1212.0～HSX1212.15
1076 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1205.0～HSX1205.15|(% style="width:191px" %)HSX1213.0～HSX1213.15
1077 |(% colspan="1" rowspan="16" style="width:135px" %)5|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX614.0～HSX614.15|(% style="width:191px" %)HSX622.0～HSX622.15
1078 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX615.0～HSX615.15|(% style="width:191px" %)HSX623.0～HSX623.15
1079 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX616.0～HSX616.15|(% style="width:191px" %)HSX624.0～HSX624.15
1080 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX617.0～HSX617.15|(% style="width:191px" %)HSX625.0～HSX625.15
1081 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX618.0～HSX618.15|(% style="width:191px" %)HSX626.0～HSX626.15
1082 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX619.0～HSX619.15|(% style="width:191px" %)HSX627.0～HSX627.15
1083 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX620.0～HSX620.15|(% style="width:191px" %)HSX628.0～HSX628.15
1084 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX621.0～HSX621.15|(% style="width:191px" %)HSX629.0～HSX629.15
1085 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1214.0～HSX1214.15|(% style="width:191px" %)HSX1222.0～HSX1222.15
1086 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1215.0～HSX1215.15|(% style="width:191px" %)HSX1223.0～HSX1223.15
1087 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1216.0～HSX1216.15|(% style="width:191px" %)HSX1224.0～HSX1224.15
1088 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1217.0～HSX1217.15|(% style="width:191px" %)HSX1225.0～HSX1225.15
1089 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1218.0～HSX1218.15|(% style="width:191px" %)HSX1226.0～HSX1226.15
1090 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1219.0～HSX1219.15|(% style="width:191px" %)HSX1227.0～HSX1227.15
1091 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1220.0～HSX1220.15|(% style="width:191px" %)HSX1228.0～HSX1228.15
1092 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1221.0～HSX1221.15|(% style="width:191px" %)HSX1229.0～HSX1229.15
1093 |(% colspan="1" rowspan="16" style="width:135px" %)6|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX630.0～HSX630.15|(% style="width:191px" %)HSX638.0～HSX638.15
1094 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX631.0～HSX631.15|(% style="width:191px" %)HSX639.0～HSX639.15
1095 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX632.0～HSX632.15|(% style="width:191px" %)HSX640.0～HSX640.15
1096 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX633.0～HSX633.15|(% style="width:191px" %)HSX641.0～HSX641.15
1097 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX634.0～HSX634.15|(% style="width:191px" %)HSX642.0～HSX642.15
1098 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX635.0～HSX635.15|(% style="width:191px" %)HSX643.0～HSX643.15
1099 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX636.0～HSX636.15|(% style="width:191px" %)HSX644.0～HSX644.15
1100 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX637.0～HSX637.15|(% style="width:191px" %)HSX645.0～HSX645.15
1101 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1230.0～HSX1230.15|(% style="width:191px" %)HSX1238.0～HSX1238.15
1102 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1231.0～HSX1231.15|(% style="width:191px" %)HSX1239.0～HSX1239.15
1103 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1232.0～HSX1232.15|(% style="width:191px" %)HSX1240.0～HSX1240.15
1104 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1233.0～HSX1233.15|(% style="width:191px" %)HSX1241.0～HSX1241.15
1105 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1234.0～HSX1234.15|(% style="width:191px" %)HSX1242.0～HSX1242.15
1106 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1235.0～HSX1235.15|(% style="width:191px" %)HSX1243.0～HSX1243.15
1107 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1236.0～HSX1236.15|(% style="width:191px" %)HSX1244.0～HSX1244.15
1108 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1237.0～HSX1237.15|(% style="width:191px" %)HSX1245.0～HSX1245.15
1109 |(% colspan="1" rowspan="16" style="width:135px" %)7|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX646.0～HSX646.15|(% style="width:191px" %)HSX654.0～HSX654.15
1110 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX647.0～HSX647.15|(% style="width:191px" %)HSX655.0～HSX655.15
1111 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX648.0～HSX648.15|(% style="width:191px" %)HSX656.0～HSX656.15
1112 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX649.0～HSX649.15|(% style="width:191px" %)HSX657.0～HSX657.15
1113 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX650.0～HSX650.15|(% style="width:191px" %)HSX658.0～HSX658.15
1114 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX651.0～HSX651.15|(% style="width:191px" %)HSX659.0～HSX659.15
1115 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX652.0～HSX652.15|(% style="width:191px" %)HSX660.0～HSX660.15
1116 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX653.0～HSX653.15|(% style="width:191px" %)HSX661.0～HSX661.15
1117 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1246.0～HSX1246.15|(% style="width:191px" %)HSX1254.0～HSX1254.15
1118 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1247.0～HSX1247.15|(% style="width:191px" %)HSX1255.0～HSX1255.15
1119 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1248.0～HSX1248.15|(% style="width:191px" %)HSX1256.0～HSX1256.15
1120 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1249.0～HSX1249.15|(% style="width:191px" %)HSX1257.0～HSX1257.15
1121 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1250.0～HSX1250.15|(% style="width:191px" %)HSX1258.0～HSX1258.15
1122 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1251.0～HSX1251.15|(% style="width:191px" %)HSX1259.0～HSX1259.15
1123 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1252.0～HSX1252.15|(% style="width:191px" %)HSX1260.0～HSX1260.15
1124 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1253.0～HSX1253.15|(% style="width:191px" %)HSX1261.0～HSX1261.15
1125 |(% colspan="1" rowspan="16" style="width:135px" %)8|(% style="width:102px" %)0～15|(% style="width:185px" %)HSX662.0～HSX662.15|(% style="width:191px" %)HSX670.0～HSX670.15
1126 |(% style="width:102px" %)16～31|(% style="width:185px" %)HSX663.0～HSX663.15|(% style="width:191px" %)HSX671.0～HSX671.15
1127 |(% style="width:102px" %)32～47|(% style="width:185px" %)HSX664.0～HSX664.15|(% style="width:191px" %)HSX672.0～HSX672.15
1128 |(% style="width:102px" %)48～63|(% style="width:185px" %)HSX665.0～HSX665.15|(% style="width:191px" %)HSX673.0～HSX673.15
1129 |(% style="width:102px" %)64～79|(% style="width:185px" %)HSX666.0～HSX666.15|(% style="width:191px" %)HSX674.0～HSX674.15
1130 |(% style="width:102px" %)80～95|(% style="width:185px" %)HSX667.0～HSX667.15|(% style="width:191px" %)HSX675.0～HSX675.15
1131 |(% style="width:102px" %)96～111|(% style="width:185px" %)HSX668.0～HSX668.15|(% style="width:191px" %)HSX676.0～HSX676.15
1132 |(% style="width:102px" %)112～127|(% style="width:185px" %)HSX669.0～HSX669.15|(% style="width:191px" %)HSX677.0～HSX677.15
1133 |(% style="width:102px" %)128～143|(% style="width:185px" %)HSX1262.0～HSX1262.15|(% style="width:191px" %)HSX1270.0～HSX1270.15
1134 |(% style="width:102px" %)144～159|(% style="width:185px" %)HSX1263.0～HSX1263.15|(% style="width:191px" %)HSX1271.0～HSX1271.15
1135 |(% style="width:102px" %)160～175|(% style="width:185px" %)HSX1264.0～HSX1264.15|(% style="width:191px" %)HSX1272.0～HSX1272.15
1136 |(% style="width:102px" %)176～191|(% style="width:185px" %)HSX1265.0～HSX1265.15|(% style="width:191px" %)HSX1273.0～HSX1273.15
1137 |(% style="width:102px" %)192～207|(% style="width:185px" %)HSX1266.0～HSX1266.15|(% style="width:191px" %)HSX1274.0～HSX1274.15
1138 |(% style="width:102px" %)208～223|(% style="width:185px" %)HSX1267.0～HSX1267.15|(% style="width:191px" %)HSX1275.0～HSX1275.15
1139 |(% style="width:102px" %)224～239|(% style="width:185px" %)HSX1268.0～HSX1268.15|(% style="width:191px" %)HSX1276.0～HSX1276.15
1140 |(% style="width:102px" %)240～255|(% style="width:185px" %)HSX1269.0～HSX1269.15|(% style="width:191px" %)HSX1277.0～HSX1277.15
1141 |(% rowspan="4" style="width:135px" %)9|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX678.0~~678.15|(% style="width:191px" %)HSX686.0~~686.15
1142 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX679.0~~679.15|(% style="width:191px" %)HSX687.0~~687.15
1143 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX680.0~~680.15|(% style="width:191px" %)HSX688.0~~688.15
1144 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX681.0~~681.15|(% style="width:191px" %)HSX689.0~~689.15
1145 |(% rowspan="4" style="width:135px" %)10|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX694.0~~694.15|(% style="width:191px" %)HSX702.0~~702.15
1146 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX695.0~~695.15|(% style="width:191px" %)HSX703.0~~703.15
1147 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX696.0~~696.15|(% style="width:191px" %)HSX704.0~~704.15
1148 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX697.0~~697.15|(% style="width:191px" %)HSX705.0~~705.15
1149 |(% rowspan="4" style="width:135px" %)11|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX710.0~~710.15|(% style="width:191px" %)HSX718.0~~718.15
1150 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX711.0~~711.15|(% style="width:191px" %)HSX719.0~~719.15
1151 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX712.0~~712.15|(% style="width:191px" %)HSX720.0~~720.15
1152 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX713.0~~713.15|(% style="width:191px" %)HSX721.0~~721.15
1153 |(% rowspan="4" style="width:135px" %)12|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX726.0~~726.15|(% style="width:191px" %)HSX734.0~~734.15
1154 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX727.0~~727.15|(% style="width:191px" %)HSX735.0~~735.15
1155 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX728.0~~728.15|(% style="width:191px" %)HSX736.0~~736.15
1156 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX729.0~~729.15|(% style="width:191px" %)HSX737.0~~737.15
1157 |(% rowspan="4" style="width:135px" %)13|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX742.0~~742.15|(% style="width:191px" %)HSX750.0~~750.15
1158 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX743.0~~743.15|(% style="width:191px" %)HSX751.0~~751.15
1159 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX744.0~~744.15|(% style="width:191px" %)HSX752.0~~752.15
1160 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX745.0~~745.15|(% style="width:191px" %)HSX753.0~~753.15
1161 |(% rowspan="4" style="width:135px" %)14|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX758.0~~758.15|(% style="width:191px" %)HSX766.0~~766.15
1162 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX759.0~~759.15|(% style="width:191px" %)HSX767.0~~767.15
1163 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX760.0~~760.15|(% style="width:191px" %)HSX768.0~~768.15
1164 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX761.0~~761.15|(% style="width:191px" %)HSX769.0~~769.15
1165 |(% rowspan="4" style="width:135px" %)15|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX774.0~~774.15|(% style="width:191px" %)HSX782.0~~782.15
1166 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX775.0~~775.15|(% style="width:191px" %)HSX783.0~~783.15
1167 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX776.0~~776.15|(% style="width:191px" %)HSX784.0~~784.15
1168 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX777.0~~777.15|(% style="width:191px" %)HSX785.0~~785.15
1169 |(% rowspan="4" style="width:135px" %)16|(% style="width:102px" %)0~~15|(% style="width:185px" %)HSX790.0~~790.15|(% style="width:191px" %)HSX798.0~~798.15
1170 |(% style="width:102px" %)16~~31|(% style="width:185px" %)HSX791.0~~791.15|(% style="width:191px" %)HSX799.0~~799.15
1171 |(% style="width:102px" %)32~~47|(% style="width:185px" %)HSX792.0~~792.15|(% style="width:191px" %)HSX800.0~~800.15
1172 |(% style="width:102px" %)48~~63|(% style="width:185px" %)HSX793.0~~793.15|(% style="width:191px" %)HSX801.0~~801.15