Wiki source code of 16 Faulty Troubleshoot

Version 5.1 by Stone Wu on 2022/08/08 10:59

version	line-number	content
3.1	1	= 1 Display faulty =
1.1	2
	3	The following is mainly talking about the how to judge and treat the HMI when the users come across the faulty issue.
	4
3.1	5	There are mainly three kinds of most common display failures:
1.1	6
3.1	7	1. Black screen;
	8	1. White screen,
	9	1. Blurry screen.
	10
1.1	11	In view of these three failure phenomena, the judgments and solutions are as follow.
	12
3.1	13	== Black screen ==
1.1	14
3.1	15	After the HMI is powered on, the screen is black, and the bepper keeps repeating a beep at a certain frequency, indicating that the power supply is insufficient.
1.1	16
3.1	17	* Please use the power supply with Voltage DC12V~~30V, Output current 500mA and above.
1.1	18
3.1	19	After the HMI is powered on, the screen is always black, the beeper does not sound at all and all lights off:
1.1	20
3.1	21	* Check whether the power supply wiring is OK, is it the wiring has poor contact or not. And use the multimeter to test whether the terminal head of power supply has 12~~30V DC, pay attention to the positive and negative poles cannot be reversed.
1.1	22
3.1	23	After the HMI is powered one, the screen can show the LOGO, the beeper beep once, the power light is on, and the screen is turning into black after loading into the project screen:
1.1	24
3.1	25	* Check whether the project is lost, redownload a normal project. After the HMI is restarted, whether it can back to normal;
	26	** Normal download but still black: The underlying file is lost;
	27	** Cannot download: The hardware flash issue;
1.1	28
3.1	29	After the HMI is powered on, the screen is always black, the beeper has a beep, and the power light is on:
1.1	30
3.1	31	* Method 1: Touch the screen see whether it can light on the TCH(touch) light.
	32	** If the touch light does not turn on, it is mostly a motherboard problem, please replace a normal motherboard.
	33	** If the touch light is on:
	34	* It may be the lcd problem, please confirm whether the contact between the lcd and the motherboard is intact, and whether the lcd cable is oxidized.
	35	** If it is confirmed that the contact is good and not oxidized, please try with a new lcd screen;
	36	** If the replacement of the touch screen still does not work, it means the motherboard is faulty, please replace with a normal motherboard.
	37	* Method 2: Click on the upper right corner of HMI to see if it can enter the backstage.
	38	** If yes, it can enter the backstage interface, please check whether the LCD is in good contact, whether the cable is oxidized, or try to replace the normal LCD;
	39	** If not, it cannot enter that interface, please replace a normal motherboard;
1.1	40
3.1	41	After the HMI is power on, the screen is always black, the beeper does not make a beep, and the power light is on:
1.1	42
3.1	43	* Method 1: Touch the screen see whether it can light on the TCH(touch) light.
	44	** If the touch light does not turn on, it is mostly a motherboard problem, please replace with a normal motherboard;
	45	** If the touch light is on:
	46	* It may be the lcd problem, please confirm whether the contact between the lcd and the motherboard is intact, and whether the lcd cable is oxidized.
	47	** If it is confirmed that the contact is good and not oxidized, please try with a new lcd screen;
	48	** If the replacement of the touch screen still does not work, it means the motherboard is faulty, please replace with a normal motherboard.
	49	* Method 2: Click on the upper right corner of HMI to see if it can enter the backstage.
	50	** If yes, it can enter the backstage interface, please check whether the LCD is in good contact, whether the cable is oxidized, or try to replace the normal LCD;
1.1	51
	52	-After the HMI is power on, the screen is always black, the beeper does not make a beep, and the power, touch and com light all three are light on:
	53
3.1	54	* Method 1: Click on the upper right corner of HMI to see if it can enter the backstage.
	55	** If yes, it can enter the backstage interface, it means it is a hardware issue, please replace the motherboard;
	56	** If not, it cannot enter that interface, it means the firmware is lost, please replace the motherboard;
	57	* Method 2: Connect to the PC by a USB-B cable:
	58	** If it can be recognized USB, it means a hardware problem, please replace the motherboard;
	59	** If not recognized, it means that the firmware files are missing, please replace the motherboard;
1.1	60
3.1	61	== Blank screen (White screen) ==
1.1	62
3.1	63	Please make sure the voltage used is DC12V~~30V, Output current 500mA Powered by switching power supply and above, and the wiring is correct.
1.1	64
3.1	65	After the HMI is powered one, the screen can show the LOGO, the beeper beep once, the power light is on, and the screen is turning into blank after loading into the project screen:
1.1	66
3.1	67	* Check whether the project is lost, redownload a normal project. After the HMI is restarted, whether it can back to normal;
	68	** Normal download but still blank: The underlying file is lost;
	69	** Cannot download: The hardware flash issue;
1.1	70
3.1	71	After the HMI is powered on, the screen is always blank, the beeper has a beep, and the power light is on:
1.1	72
3.1	73	* Method 1: Touch the screen see whether it can light on the TCH(touch) light.
	74	** If the touch light does not turn on, it is mostly a motherboard problem, please replace with a normal motherboard;
	75	** If the touch light is on:
	76	* It may be the lcd problem, please confirm whether the contact between the lcd and the motherboard is intact, and whether the lcd cable is oxidized.
	77	** If it is confirmed that the contact is good and not oxidized, please try with a new lcd screen;
	78	** If the replacement of the touch screen still does not work, it means the motherboard is faulty, please replace with a normal motherboard.
	79	* Method 2: Click on the upper right corner of HMI to see if it can enter the backstage.
	80	** If yes, it can enter the backstage interface, please check whether the LCD is in good contact, whether the cable is oxidized, or try to replace the normal LCD;
	81	** If not, please replace the motherboard;
1.1	82
3.1	83	After the HMI is powered on, the screen is always blank, the beeper does not make a beep, and the power light is on:
1.1	84
3.1	85	* Method 1: Touch the screen see whether it can light on the TCH(touch) light.
	86	** If the touch light does not turn on, it is mostly a motherboard problem, please replace with a normal motherboard;
	87	** If the touch light is on:
	88	* It may be the lcd problem, please confirm whether the contact between the lcd and the motherboard is intact, and whether the lcd cable is oxidized.
	89	** If it is confirmed that the contact is good and not oxidized, please try with a new lcd screen;
	90	** If the replacement of the touch screen still does not work, it means the motherboard is faulty, please replace with a normal motherboard.
	91	* Method 2: Click on the upper right corner of HMI to see if it can enter the backstage.
	92	** If yes, it can enter the backstage interface, please check whether the LCD is in good contact, whether the cable is oxidized, or try to replace the normal LCD;
	93	** If not, please replace the motherboard;
1.1	94
3.1	95	== Blurry screen ==
1.1	96
3.1	97	Please make sure the voltage used is DC12V~~30V, Output current 500mA Powered by switching power supply and above, and the wiring is correct.
1.1	98
3.1	99	After the HMI is powered one, the screen can show the LOGO, the beeper beep once, the power light is on, and the screen is turning into blurred after loading into the project screen:
1.1	100
3.1	101	* Check whether the project is lost, redownload a normal project. After the HMI is restarted, whether it can back to normal;
	102	** Normal download but still blurry: The underlying file is lost;
	103	** Cannot download: The hardware flash issue;
1.1	104
3.1	105	After the HMI is powered on, the screen is always blurred, the beeper has a beep, and the power light is on:
1.1	106
3.1	107	* Method 1: Touch the screen see whether it can light on the TCH(touch) light.
	108	** If the touch light does not turn on, it is mostly a motherboard problem, please replace with a normal motherboard;
	109	** If the touch light is on:
	110	* It may be the lcd problem, please confirm whether the contact between the lcd and the motherboard is intact, and whether the lcd cable is oxidized.
	111	** If it is confirmed that the contact is good and not oxidized, please try with a new lcd screen;
	112	** If the replacement of the touch screen still does not work, it means the motherboard is faulty, please replace with a normal motherboard.
	113	* Method 2: Click on the upper right corner of HMI to see if it can enter the backstage.
	114	** If yes, it can enter the backstage interface, please check whether the LCD is in good contact, whether the cable is oxidized, or try to replace the normal LCD;
	115	** If not, please replace the motherboard;
1.1	116
3.1	117	After the HMI is powered on, the screen is always blurred, the beeper does not make a beep, and the power light is on:
1.1	118
3.1	119	* Method 1: Touch the screen see whether it can light on the TCH(touch) light.
	120	** If the touch light does not turn on, it is mostly a motherboard problem, please replace with a normal motherboard;
	121	** If the touch light is on:
	122	* It may be the lcd problem, please confirm whether the contact between the lcd and the motherboard is intact, and whether the lcd cable is oxidized.
	123	** If it is confirmed that the contact is good and not oxidized, please try with a new lcd screen;
	124	** If the replacement of the touch screen still does not work, it means the motherboard is faulty, please replace with a normal motherboard.
	125	* Method 2: Click on the upper right corner of HMI to see if it can enter the backstage.
	126	** If yes, it can enter the backstage interface, please check whether the LCD is in good contact, whether the cable is oxidized, or try to replace the normal LCD;
	127	** If not, please replace the motherboard;
1.1	128
3.1	129	= 2 USB faulty =
1.1	130
	131	This document is mainly teaching that how to locate the problem if the HMI cannot be detected when connect to PC by the USB cable. Totally there are 3 aspects need to consider: PC USB port, HMI USB port, USB cable.
	132
5.1	133	== PC USB port ==
1.1	134
3.1	135	See whether the problem is from PC Port, if change another one USB port, can it be OK?
1.1	136
5.1	137	== USB cable ==
1.1	138
3.1	139	See whether the problem is from cable, if change another one cable, can it be OK?
1.1	140
5.1	141	== HMI USB-B port ==
1.1	142
3.1	143	See whether the problem just happen on the single one HMI, if at the same condition of PC and cable, is it able to detect the others HMI?
1.1	144
3.1	145	* See whether Device Manager can detect the USB.
	146	* Run the PIStudio as Administrator.
1.1	147
3.1	148	== When Happen Issue ==
1.1	149
3.1	150	First time usage and it happened: It probably the pseudo welding problem.
1.1	151
3.1	152	Already used for a while, USB is OK and fine before: Maybe it is caused by interference from the site, check all the devices whether are well grounded or not.
1.1	153
3.1	154	= 3 Touch faulty =
1.1	155
	156	This document is mainly teaching that how to locate the problem if the HMI cannot exit the calibration screen. Totally there are 3 aspects need to consider: calibrate tool, calibration settings, touch board.
	157
3.1	158	== Calibrate rool ==
1.1	159
	160	Please do not use the finger to calibrate the screen, it is the most imprecise method to do so. Please use the pen or screwdriver to calibrate it. When finish the five coordinates, please notice whether there is a pop-up tips on the middle screen. If it is succeed, it will show green tips, while not, it will show a red one. Please refer to the following video:
	161
	162	[[Video Link>>https://drive.google.com/file/d/1diec_1Pa3ZbaKRY8YCm6L7iO8lJBU4I7/view?usp=sharing]]
	163
3.1	164	== Calibration settings ==
1.1	165
	166	Connect the HMI to PC Download tool. Please try to delete the exists calibration file and try to calibrate again. See whether it can help or not.
	167
	168	(% style="text-align:center" %)
3.1	169	[[image:calibrate.png\|\|height="428" width="700" class="img-thumbnail"]]
1.1	170
3.1	171	== Touch board ==
1.1	172
	173	-If HMI is on the cabinet, please uninstall it from cabinet and try again. If lock too tight on the cabinet, it will influent the touch operations.
	174
	175	-Try to remove the front film sticker.
	176
	177	-If all options above are still not help to the calibration, please replace the new touch board.

Wiki source code of 16 Faulty Troubleshoot

Navigation

Table of Contents