| ... |
... |
@@ -1,52 +1,0 @@ |
| 1 |
|
-= {{id name="HCrouzet"/}}Crouzet = |
| 2 |
|
- |
| 3 |
|
-== {{id name="HM328FBD29"/}}**M3 (FBD)** == |
| 4 |
|
- |
| 5 |
|
-Support Series: Crouzet Millenium 3 CD12/CB12 |
| 6 |
|
- |
| 7 |
|
-**HMI Settings** |
| 8 |
|
- |
| 9 |
|
-|=Item|=Recommended|=Note |
| 10 |
|
-|=Protocol|CROUZET M3 (FBD)| |
| 11 |
|
-|=Connection|RS232| |
| 12 |
|
-|=Baud rate|115200| |
| 13 |
|
-|=Stop bits|1| |
| 14 |
|
-|=Data bits|7| |
| 15 |
|
-|=Parity|EVEN| |
| 16 |
|
-|=PLC Station No.|1| |
| 17 |
|
-|=HMI Station No.|0| |
| 18 |
|
- |
| 19 |
|
- **Address List** |
| 20 |
|
- |
| 21 |
|
-|=**Type**|=**Device registers**|=**Format**|=**Range**|=Note |
| 22 |
|
-|(% rowspan="4" %)Bit|I|I DD|1~~99|Input |
| 23 |
|
-|SLIBit|SLIBit DD.dd|1.0~~24.15|Serial Link Input |
| 24 |
|
-|SLOBit|SLOBit DD.dd|25.0~~48.15|Serial Link Output(Read only) |
| 25 |
|
-|State|State D|1~~1|PLC state(Read only) |
| 26 |
|
-|(% rowspan="5" %)Word|AI|AI DD|1~~99|Analog Input |
| 27 |
|
-|SLIn|SLIn DD|1~~24|Serial Link Input |
| 28 |
|
-|SLOut|SLOut DD|25~~48|Serial Link Output(Read only) |
| 29 |
|
-|Time|Time D|1~~6|((( |
| 30 |
|
-Time1: Second |
| 31 |
|
- |
| 32 |
|
-Time2: Minute |
| 33 |
|
- |
| 34 |
|
-Time3: Hour |
| 35 |
|
- |
| 36 |
|
-Time4: Day |
| 37 |
|
- |
| 38 |
|
-Time5: Month |
| 39 |
|
- |
| 40 |
|
-Time6: Year |
| 41 |
|
-))) |
| 42 |
|
-|Order|Order D|1~~1|((( |
| 43 |
|
-Running command(Write only) |
| 44 |
|
- |
| 45 |
|
-~=2: Run mode; =1: Stop mode; |
| 46 |
|
-))) |
| 47 |
|
- |
| 48 |
|
-**Cable Wiring** |
| 49 |
|
- |
| 50 |
|
-{{id name="ICrouzetRS232.png"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_23bb78b6e7e7eeaf.png||alt="CrouzetRS232.png" height="247" width="400"]] |
| 51 |
|
- |
| 52 |
|
-**✎Note: **As the communication driver remark mentioned, this protocol requires the DB9 serial port pin 4. But pin 4 is not define, not used or not useful(e.g. the pin 4 is the B- terminal of 485_2 of ig series) for PI HMIs, so it need the user to solder a Pull-up resistor to make the pin 4 working. As for how to solder the resistor on the motherboard, please contact with Wecon technical support for the details. |
