Changes for page SHIMADEN

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,0 +1,161 @@
	1	+= {{id name="HSHIMADEN"/}}**SHIMADEN** =
	2	+
	3	+== {{id name="HFP23Series"/}}**FP23 Series** ==
	4	+
	5	+Supported series: SHIMADEN FP23 series
	6	+
	7	+**HMI Setting**
	8	+
	9	+|**Items**|**Settings**|**Note**
	10	+|Protocol|SHIMADEN FP23 series|
	11	+|Connection|RS485 (9600, 1, 7, EVEN)|
	12	+|Port No.|None|
	13	+|PLC station No.|0|
	14	+
	15	+**Address List**
	16	+
	17	+|**Device address**|**HMI register**|**Address range**|**Type**
	18	+|0040-0043(HEX)|FP040|100064-200067|Read only
	19	+|0100-010B(HEX)|FP100|100256-200267|Read only
	20	+|0110-0142(HEX)|FP110|100272-200322|Read only
	21	+|0182-0252(HEX)|FP182|100386-200594|Write only
	22	+|0280-0281(HEX)|FP280|100640-200641|Read only
	23	+|0300-030B(HEX)|FP300|100768-200779|Read and write
	24	+|0380-039F(HEX)|FP380|100896-200927|Read and write
	25	+|0400-04D7(HEX)|FP400|101024-201239|Read and write
	26	+|0500-05B0(HEX)|FP500|101280-201456|Read and write
	27	+|0600-0670(HEX)|FP600|101536-201814|Read and write
	28	+|0720-0738(HEX)|FP720|101824-201848|Read and write
	29	+|0800-083F(HEX)|FP800|102048-202111|Read and write
	30	+|0900-0952(HEX)|FP900|102304-202386|Read and write
	31	+|　|Ctrl|0-2|
	32	+
	33	+**✎Note:**
	34	+
	35	+* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
	36	+* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in FP23;
	37	+* The Ctrl register is used to store the control group number and BCC check mode.
	38	+
	39	+**Ctrl Register Description**
	40	+
	41	+* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
	42	+* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
	43	+* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
	44	+* Ctrl3 reserved
	45	+
	46	+**✎Note:**
	47	+
	48	+After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
	49	+
	50	+**Cable Wiring**
	51	+
	52	+{{id name="I12.PLCProtocol_html_5e9a81a14106da9e.png-1"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_7b2556c42d43a768.png||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
	53	+
	54	+{{id name="I12.PLCProtocol_html_1897d92be6948d58.png-2"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_c6d16b5adff76549.png||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
	55	+
	56	+**✎Note:** COM3 only available in PI8000/PI9000 series.
	57	+
	58	+== {{id name="HSR90"/}}**SR90** ==
	59	+
	60	+Supported series: SHIMADEN SR90 series
	61	+
	62	+**HMI Setting**
	63	+
	64	+|**Items**|**Settings**|**Note**
	65	+|Protocol|SHIMADEN SR90|
	66	+|Connection|RS485 (1200, 1, 7, EVEN)|
	67	+|Port No.|None|
	68	+|PLC station No.|0|
	69	+
	70	+**Address List**
	71	+
	72	+|**Device address**|**HMI register**|**Address range**|**Type**
	73	+|0040-0043 (HEX)|SR040|100064-100067|Read only
	74	+|0100-010A(HEX)|SR0100|100256-100266|Read only
	75	+|0182-018C(HEX)|SR0182|100386-100396|Write only
	76	+|0300-04FE(HEX)|SR0300|100768-101278|Write/read
	77	+|0500-050B(HEX)|SR0500|101280-101291|Write/read
	78	+|0590-0611(HEX)|SR0590|101424-101553|Write/read
	79	+|0701-0709(HEX)|SR0701|101793-101801|Write/read
	80	+| |Ctrl|0-2|~-~-
	81	+
	82	+**✎Note:**
	83	+
	84	+* The upper 2 bits of the address of HMIs are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
	85	+* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in SR90;
	86	+* The Ctrl register is used to store the control group number and BCC check mode. See how to use it below;
	87	+
	88	+**Ctrl Register Description**
	89	+
	90	+* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
	91	+* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
	92	+* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
	93	+* Ctrl3 reserved
	94	+
	95	+**✎Note:**
	96	+
	97	+After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
	98	+
	99	+**Cable Wiring**
	100	+
	101	+{{id name="I12.PLCProtocol_html_5e9a81a14106da9e.png-2"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_7b2556c42d43a768.png||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
	102	+
	103	+{{id name="I12.PLCProtocol_html_1897d92be6948d58.png-3"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_c6d16b5adff76549.png||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
	104	+
	105	+**✎Note:** COM3 only available in PI8000/PI9000 series.
	106	+
	107	+== {{id name="HMR13Series28Standard29"/}}**MR13 Series(Standard)** ==
	108	+
	109	+Supported series: SHIMADEN MR13 series
	110	+
	111	+**HMI Setting**
	112	+
	113	+|**Items**|**Settings**|**Note**
	114	+|Protocol|SHIMADEN standard protocol|
	115	+|Connection|RS485 (1200, 1, 7, EVEN)|
	116	+|Port No.|None|
	117	+|PLC station No.|0|
	118	+
	119	+**Address List**
	120	+
	121	+|**Device address**|**HMI register**|**Address range**|**Type**
	122	+|0100-010B(HEX)|MR100|100256-300267|Read only
	123	+|0111-0126(HEX)|MR111|100273-300294|Read only
	124	+|0184-0192(HEX)|MR184|100388-300402|Write only
	125	+|0280-0282(HEX)|MR280|100640-300642|Read only
	126	+|0300-030B(HEX)|MR300|100768-300779|Read/write
	127	+|0314-0317(HEX)|MR314|100788-300791|Read/write
	128	+|031A(HEX)|MR31A|100794-300794|Read/write
	129	+|0320-0321(HEX)|MR320|100800-300801|Read/write
	130	+|0400-0504(HEX)|MR400|101024-301284|Read/write
	131	+|0506(HEX)|MR506|101286-301286|Read/write
	132	+|0510-0514(HEX)|MR510|101296-301300|Read/write
	133	+|0516-0524(HEX)|MR516|101302-301316|Read/write
	134	+|0526(HEX)|MR526|101318-301318|Read/write
	135	+|0580-08C3(HEX)|MR580|101408-302243|Read/write
	136	+|~-~-|Ctrl|0-2|~-~-
	137	+
	138	+**✎Note:**
	139	+
	140	+* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
	141	+* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in MR13;
	142	+* The Ctrl register is used to store the control group number and BCC check mode.
	143	+
	144	+**Ctrl Register Description**
	145	+
	146	+* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
	147	+* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR, STX_ETX_CR LF and @_:_CR .
	148	+* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
	149	+* Ctrl3 reserved
	150	+
	151	+**✎Note:**
	152	+
	153	+After reloading project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
	154	+
	155	+**Cable Wiring**
	156	+
	157	+{{id name="I12.PLCProtocol_html_5e9a81a14106da9e.png-3"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_7b2556c42d43a768.png||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
	158	+
	159	+{{id name="I12.PLCProtocol_html_1897d92be6948d58.png-4"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_c6d16b5adff76549.png||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
	160	+
	161	+**✎Note:** COM3 only available in PI8000/PI9000 series.