Wiki source code of Xinje

Last modified by Hunter on 2023/09/22 15:23

version	line-number	content
11.1	1	= XC MODBUS =
2.1	2
15.2	3	Support Series: Xinjie XC Series
	4
2.1	5	HMI Settings
	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|XINJE XC MODBUS\|
	9	\|Connection\|RS232\|
	10	\|Baud rate\|19200\|
	11	\|Data bit\|8\|
	12	\|Parity\|EVEN\|
	13	\|Stop bit\|1\|
17.1	14	\|PLC station No.\|1\|Need to be same as PLC setting
2.1	15
	16	Address List
	17
15.2	18	\|=Type\|=(% style="width: 301px;" %)Device registers\|=(% style="width: 235px;" %)Format\|=Range\|=Note
	19	\|(% colspan="1" rowspan="6" %)Bit\|(% style="width:301px" %)M\|(% style="width:235px" %)MDDDD\|0~~8511\|Internal Relay
	20	\|(% style="width:301px" %)X\|(% style="width:235px" %)XOOOO\|0~~1747\|Input Relay
	21	\|(% style="width:301px" %)Y\|(% style="width:235px" %)YOOOO\|0~~1747\|Output Relay
	22	\|(% style="width:301px" %)S\|(% style="width:235px" %)SDDDD\|0~~1023\|Flow
	23	\|(% style="width:301px" %)T\|(% style="width:235px" %)TDDD\|0~~618\|Timer
	24	\|(% style="width:301px" %)C\|(% style="width:235px" %)CDDD\|0~~634\|Counter
	25	\|(% colspan="1" rowspan="4" %)Word\|(% style="width:301px" %)D\|(% style="width:235px" %)DDDDD\|0~~8511\|Data Register
	26	\|(% style="width:301px" %)TD\|(% style="width:235px" %)TDDDD\|0~~618\|Timer
	27	\|(% style="width:301px" %)CD\|(% style="width:235px" %)CDDDD\|0~~634\|Counter
	28	\|(% style="width:301px" %)FD\|(% style="width:235px" %)FDDDDD\|0~~8511\|FlashROM Register
2.1	29
16.1	30	PLC Settings
2.1	31
16.1	32	Create the new project, and select the specific model according to the actual PLC
	33
	34	(% style="text-align:center" %)
	35	[[image:XinjieXCcreatenew.png]]
	36
	37	Program the PLC
	38
	39	(% style="text-align:center" %)
	40	[[image:XinjieXCPrg.png]]
	41
	42	Connect PLC with PC through RS232-USB converter cable. Click [Option]-[Software Serial Port Config] to open the software connection setup window, and select the serial port, if the red text prompt "Connect To PLC Succeeded", which means the connection is setup successfully, then click OK to save the settings.
	43
	44	(% style="text-align:center" %)
	45	[[image:XinjieXCPCconn.png]]
	46
	47	Change the PLC communication setup if required. Double click the tree node [PLC Serial Port] from Project tree. And change Modbus parameters, then click [Write to PLC] and OK to finish.
	48
	49	(% style="text-align:center" %)
	50	[[image:XinjieXCPLCModbusConfig.png]]
	51
	52	Click [Online]-[Download Program] to download program into PLC. And the download pop up window would pop up, then click OK.
	53
	54	(% style="text-align:center" %)
	55	[[image:XinjieXCDownloadPLC.png]]
	56
2.1	57	Cable Wiring
	58
	59
16.1	60	(% style="text-align:center" %)
15.2	61	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_58247140e9fe4230.png\|\|alt="image-20220830154131-2.png" height="240" width="395"]]
2.1	62
11.1	63	= XD/XE MODBUS =
2.1	64
11.1	65	Supported Series: Xinjie XD Series
	66
2.1	67	HMI Settings
	68
	69	\|=Item\|=Settings\|=Note
	70	\|Protocol\|XINJE XD/XC MODBUS\|
	71	\|Connection\|RS232\|
	72	\|Baud rate\|19200\|
	73	\|Data bit\|8\|
	74	\|Parity\|EVEN\|
	75	\|Stop bit\|1\|
11.1	76	\|PLC station No.\|1\|Need to be same as PLC setting
2.1	77
	78	Address List
	79
11.1	80	\|=Type\|=Device registers\|=Format\|=Range\|=Note
14.2	81	\|(% colspan="1" rowspan="18" %)Bit\|M\|MDDDDD\|0~~74999\|Internal Relay
	82	\|X1xx\|X1xxOOOO\|0~~1177\|Extension Module Input Relay
	83	\|X2xx\|X2xxOOO\|0~~277\|BD Card Input Relay
	84	\|X\|XOO\|0~~77\|Input Relay
	85	\|Y1xx\|Y1xxOOOO\|0~~1177\|Extenson Module Output Relay
	86	\|Y2xx\|Y2xxOOO\|0~~277\|BD Card Output Relay
	87	\|Y\|YOOOO\|0~~77\|Output Relay
	88	\|SM\|SMDDDD\|0~~4999\|Special Auxiliary Relay
	89	\|T\|TDDDD\|0~~4999\|Timer
	90	\|C\|CDDDD\|0~~4999\|Counter
	91	\|ET\|ETDD\|0~~31\|Precise Timer
15.1	92	\|SE\|SEDD\|0~~31\|Function Block WAIT Instruction Special Coil
14.3	93	\|HM\|HMDDDDD\|0~~11999\|Power Off Retentive Internal Relay
	94	\|HSC\|HSCDD\|0~~39\|High Speed Counter
15.1	95	\|HS\|HSDDD\|0~~999\|Power Off Retentive Procedure
	96	\|HT\|HTDDDD\|0~~1999\|Power Off Retentive Auxiliary Relay
14.3	97	\|HC\|HCDDDD\|0~~1999\|Power Off Retentive Counter
	98	\|S\|SDDDD\|0~~7999\|Procedure
14.2	99	\|(% colspan="1" rowspan="19" %)Word\|D\|DDDDDD\|0~~69999\|Data Register
	100	\|ID\|IDDD\|0~~99\|Analog Input
	101	\|ID1xx\|ID1xxDDD\|0~~999\|Extension Module Analog Input
	102	\|ID2xx\|ID2xxDDD\|0~~299\|BD Card Analog Input
	103	\|QD\|QDDD\|0~~99\|Analog Output
	104	\|QD1xx\|QD1xxDDD\|0~~999\|Extension Module Analog Output
	105	\|QD2xx\|QD2xxDDD\|0~~299\|BD Card Analog Output
	106	\|SD\|SDDDDD\|0~~4999\|Data Register
	107	\|TD\|TDDDD\|0~~575\|Timer
	108	\|CD\|CDDDD\|0~~575\|Counter
	109	\|ETD\|ETDDD\|0~~31\|Precise Timer
	110	\|HD\|HDDDDDD\|0~~24999\|Data Register
	111	\|HSD\|HSDDDDD\|0~~1023\|Power Off Retentive Data Register
	112	\|HTD\|HTDDD\|0~~95\|Power Off Retentive Timer
	113	\|HCD\|HCDDD\|0~~95\|Power Off Retentive Counter
	114	\|HSCD\|HSCDDD\|0~~31\|High Speed Counter
	115	\|FD\|FDDDDD\|0~~8191\|FlashROM Register
	116	\|SFD\|SFDDDDD\|0~~5999\|Special Flash Register
	117	\|FS\|FSDD\|0~~47\|Special Data Register
2.1	118
11.1	119	PLC Settings
2.1	120
11.2	121	Create the new project, and select the specific model according to the actual PLC
2.1	122
11.2	123	(% style="text-align:center" %)
	124	[[image:XinjieXDcreatenew.png]]
	125
	126	Program the PLC
	127
	128	(% style="text-align:center" %)
	129	[[image:XinjieXDLDprg.png]]
	130
	131	Connect PLC with PC through RS232-USB converter cable. Click [Option]-[Software Serial Port Config]-[Communication configuration] to open the PC connection configuration.
	132
	133	(% style="text-align:center" %)
	134	[[image:XinjieXDopenSWcom.png]]
	135
	136	New a Modbus configuration, and Click [Comm-Test] to test connection, if shows "Connect To PLC Succeeded", which means PLC connection set up successfully. And click OK to save the settings
	137
	138	(% style="text-align:center" %)
	139	[[image:XinjieXDPLCtestconn.png]]
	140
	141	Remember to click the Status cell of new created Modbus configuration for change the status into "in use", then click OK to exit.
	142
	143	(% style="text-align:center" %)
	144	[[image:XinjieXDclickto.png]]
	145
11.3	146	After done the previous steps, it would prompt like the below
11.2	147
11.4	148	(% style="text-align:center" %)
	149	[[image:XinjieXDsuccessprompt.png]]
11.3	150
13.1	151	Change the PLC communication setup if required. Click [Configure]-[PLC Comm Port Settings]-[Add]-[Modbus]. After parameters are modified, click [Write to PLC].
11.4	152
13.1	153	(% style="text-align:center" %)
	154	[[image:XinjieXDSetPLCcom0.png]]
11.5	155
13.1	156	If wrote to PLC successfully, it would prompt like the below
	157
	158	(% style="text-align:center" %)
	159	[[image:XinjieXDwriteComparadone.png]]
	160
	161	Click [Online]-[Download Program & Data], and wait for a while, the pop up window would ask for whether to stop PLC, and click [Stop PLC, contitue download]
	162
	163	(% style="text-align:center" %)
	164	[[image:XinjieXDdownload.png]]
	165
	166	And then the XDPro ask for which options want to rewrite, and click OK to finish.
	167
	168	(% style="text-align:center" %)
	169	[[image:XinjieXDdownloadopt.png]]
	170
	171	If download successfully, it would prompt like the below
	172
	173	(% style="text-align:center" %)
	174	[[image:XinjieXDcomplete.png]]
	175
2.1	176	Cable Wiring
	177
14.1	178	(% style="text-align:center" %)
	179	[[image:Xinjie.gif]]

Wiki source code of Xinje

Navigation

Table of Contents