Skip to Content
Last modified by Joe on 2025/01/10 09:30
From version 2.5
edited by Leo Wei
on 2022/07/28 11:27
Change comment: Renamed from xwiki:PLC Editor.LX3V programing manual.05 Registers.5-9 system-special address.WebHome
To version 6.1
edited by Devin Chen
on 2024/01/27 14:29
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -PLC Editor.LX3V programing manual.05 Registers.WebHome
1 +PLC Editor.05 Registers.WebHome
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.admin
1 +XWiki.DevinChen
Content
... ... @@ -48,7 +48,7 @@
48 48  cycles
49 49  )))|O|O|D8012|(% colspan="3" %)Maximum cycle/ scould time inunits of 0.1 msec|O|O|
50 50  |M8013|(% colspan="2" %)Oscillates in 1 sec cycles|O|O|D8013|(% colspan="3" %)Seconds data for use with an RTC (0-59)|O|O|
51 -|M8014|(% colspan="2" %)Oscillates in 1 min cycles|O|O|D8014|(% colspan="3" %)Minute data for use with anRTC (0-59)|O|O|
51 +|M8014|(% colspan="2" %)Oscillates in 1 min cycles|O|O|D8014|(% colspan="3" %)Minute data for use with an RTC (0-59)|O|O|
52 52  |M8015|(% colspan="2" %)When ON - clock stops, ON→OFF restarts clock|O|O|D8015|(% colspan="3" %)Hour data for use with an RTC (0-23)|O|O|
53 53  |M8016|(% colspan="2" %)(((
54 54  When ON D8013 to 19 are frozen for display but clock
... ... @@ -87,7 +87,7 @@
87 87  |M8036|(% colspan="2" %)Forced operation 2|O|O|D8036|(% colspan="3" %)Reserved| | |
88 88  |M8037|(% colspan="2" %)Forced stop|O|O|D8037|(% colspan="3" %)Reserved| | |
89 89  |M8038|(% colspan="2" %)Communication parameter setting flag|O|O|D8038|(% colspan="3" %)Reserved| | |
90 -|M8039|(% colspan="2" %)Constant scould|O|O|D8039|(% colspan="3" %)Constant scould time, default 0, in units of MS|O|O|
90 +|M8039|(% colspan="2" %)Constant scan control|O|O|D8039|(% colspan="3" %)Constant scan time, default 0, in units of MS|O|O|
91 91  |(% colspan="11" %)(((
92 92  == **Step Ladder (STL) Flags** ==
93 93  )))|
... ... @@ -153,7 +153,7 @@
153 153  |M8108|(% colspan="2" %)Reserved| | |D8108|(% colspan="3" %)Reserved| | |
154 154  |M8109|(% colspan="2" %)Output refresh error|O|O|D8109|(% colspan="3" %)Output refresh error device number;|O|O|
155 155  |(% colspan="11" %)(((
156 -== **COM1 communication settings** ==
156 +== **COM1 communication settings&BD module configuration** ==
157 157  )))|
158 158  |M8110|(% colspan="2" %)Reserved| | |D8110|(% colspan="3" %)Com1 port setting (only available in 22319, 24320, 25007 or later)|O|O|
159 159  |M8111|(% colspan="2" %)Reserved| | |D8111|(% colspan="3" %)Reserved| | |
... ... @@ -218,11 +218,11 @@
218 218  |(% colspan="11" %)(((
219 219  == **Extend function** ==
220 220  )))|
221 -|M8156|(% colspan="2" %)Reserved| | |D8156|(% colspan="3" %)Define clear signal in Y0 (ZRN) (default is 5=Y5)|O|O|
222 -|M8157|(% colspan="2" %)Reserved| | |D8157|(% colspan="3" %)Define clear signal in Y1 (ZRN) (default is 6=Y6)|O|O|
223 -|M8158|(% colspan="2" %)Reserved| | |D8158|(% colspan="3" %)Define clear signal in Y2 (ZRN) (default is 7=Y7)|O|O|
224 -|M8159|(% colspan="2" %)Reserved| | |D8159|(% colspan="3" %)Define clear signal in Y3 (ZRN) (default is 8=Y10)|O|O|
225 -|M8160|(% colspan="2" %)SWAP function is XCH|-|O|D8160|(% colspan="3" %)Define clear signal in Y4 (ZRN) (default is 9=Y11)|O|O|
221 +|M8156|(% colspan="2" %)Reserved| | |D8156|(% colspan="3" %)Reserved|O|O|
222 +|M8157|(% colspan="2" %)Reserved| | |D8157|(% colspan="3" %)Reserved|O|O|
223 +|M8158|(% colspan="2" %)Reserved| | |D8158|(% colspan="3" %)Reserved|O|O|
224 +|M8159|(% colspan="2" %)Reserved| | |D8159|(% colspan="3" %)Reserved|O|O|
225 +|M8160|(% colspan="2" %)SWAP function is XCH|-|O|D8160|(% colspan="3" %)Reserved|O|O|
226 226  |M8161|(% colspan="2" %)Bit processing mode of ASC/RS/ASCII/HEX/CCD|O|O|D8161|(% colspan="3" %)Reserved| | |
227 227  |M8162|(% colspan="2" %)High-speed connection in parallel mode|O|O|D8162|(% colspan="3" %)Reserved| | |
228 228  |M8163|(% colspan="2" %)Reserved| | |D8163|(% colspan="3" %)Reserved| | |