Changes for page 01 Program execution

Last modified by Jiahao Lai on 2025/07/18 17:39

From 17.1 to 16.1 From 34.1 to 33.1

From version 33.1

edited by Mora Zhou
on 2024/12/05 16:14

Change comment: There is no comment for this version

To version 17.1

edited by Stone Wu
on 2022/09/23 16:33

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 1 removed)
- image-20220926104203-1.jpeg

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Mora
++XWiki.Stone

Content

@@ -1,9 +1,11 @@
  = **Summary** =
--This manual provides a comprehensive introduction to the basic functions and actual use of WECON PLC Editor. It is completely aimed at zero-based readers and is an essential reference book for entry-level readers who want to quickly and fully grasp WECON PLC and WECON PLC Editor.
--This book starts with the basic product of WECON PLC and the basic concept and operation of WECON PLC Editor. It then uses a large number of cases and graphic analysis to comprehensively and deeply explain the use of WECON PLC Editor Software and the PLC program.
--WECON Technology Co., Ltd. All rights reserved.
++This manual has a comprehensive introduction to the basic functions of WECON PLC Editor and the actual use. This book is completely aimed at zero-based readers, is an essential reference book for entry-level readers to quickly and fully grasp WECON PLC and WECON PLC Editor.
++This book starts from the basic product of WECON PLC and the basic concept and operation of WECON PLC Editor. It combines with a large number of cases and graphic analysis to comprehensively and deeply explain the use of WECON PLC Editor Software, as well as PLC program.
++
++WECON technology Co., Ltd. All rights reserved.
++
  = Precautions =
  Before the installation, operation, maintenance and repair of the micro programmable control, please read this manual and other related manuals to ensure correct use. Please use it after you have mastered the operation method, safety information and all
@@ -27,8 +27,8 @@
  (((
  **✎Note:**
--* To prevent the temperature from rising, do not install at the bottom, top or vertical direction. Be sure to install it horizontally on the wall as shown on the right.
--* Please leave a space of more than 50mm between the host and other equipment or structures. Try to avoid high-voltage lines, high-voltage equipment, and power equipment.
++* To prevent the temperature from rising, do not install at the bottom, top or vertical direction.Be sure to install it horizontally on the wall as shown on the right.
++* Please leave a space of more than 50mm between the host and other equipment or structures.Try to avoid high-voltage lines, high-voltage equipment, and power equipment.
  )))
  == Wiring ==
@@ -129,7 +129,7 @@
  The initialization based on the status of the CPU module is as follows.
  * **√**: execute
--* **×**: not execute
++*  **×**: not execute
  (% class="table-bordered" %)
  |=(% rowspan="2" %)**Processing item**|=(% colspan="3" %)**Status of the CPU module**
@@ -245,7 +245,7 @@
  *1: Scan program paging: multiple scan programs are established, and each scan program is called a paging. After scan program A is executed, before scan program B is executed, it will be judged whether an event program needs to be executed.
  (% style="text-align:center" %)
--[[image:image-20220926104203-1.jpeg||class="img-thumbnail"]]
++[[image:1652247397997-492.png||class="img-thumbnail"]]
  When it is the turn of the execution sequence of event execution type program C and Y50 is ON, the program is executed.
@@ -432,7 +432,7 @@
  [[image:1-20.png||class="img-thumbnail"]]
  (% class="table-bordered" %)
--|=(% colspan="2" %)**Project**|=**Content**|=**Setting range**|=**Default**
++|(% colspan="2" %)**Project**|**Content**|**Setting range**|**Default**
  |(% colspan="2" %)Execution type|Select the type of interrupt|Not set/External input interrupt/Timer event/high-speed counter interrupt|Not set
  |(% rowspan="2" %)Timer interrupt|Time|Set the interval time for interrupt triggering|1 to 2147483647 (100us unit)|
  |priority|When multiple interrupts arrive at the same time, the order of priority execution, the smallest value is executed first|0 to 2|0
@@ -470,7 +470,7 @@
  [[image:1-23.png||class="img-thumbnail"]]
  (% class="table-bordered" %)
--|=(% colspan="2" %)**Project**|=**Content**|=**Setting range**|=**Default**
++|(% colspan="2" %)**Project**|**Content**|**Setting range**|**Default**
  |(% colspan="2" %)Execution type|Select the type of interrupt|Not set, External input interrupt, Timer event, high-speed counter interrupt|Not set
  |(% rowspan="5" %)High count interrupt|Mode|(((
  Select the type of high-speed counter interrupt:
@@ -501,7 +501,7 @@
   Description of triggering rules
  (% class="table-bordered" %)
--|=(% style="width: 135px;" %)**Mode**|=(% style="width: 187px;" %)**Configuration**|=(% style="width: 128px;" %)**The current value**|=(% style="width: 324px;" %)**Action**
++|(% style="width:135px" %)**Mode**|(% style="width:187px" %)**Configuration**|(% style="width:128px" %)**The current value**|(% style="width:324px" %)**Action**
  |(% rowspan="2" style="width:135px" %)High-speed compare interrupt (INT0)|(% rowspan="2" style="width:187px" %)Comparison value: 10000|(% style="width:128px" %)9999 → 10000|(% style="width:324px" %)Execute all programs in interrupt INT0
  |(% style="width:128px" %)10001 → 10000|(% style="width:324px" %)Execute all programs in interrupt INT0
  |(% rowspan="2" style="width:135px" %)High-speed comparison set (INT1)|(% rowspan="2" style="width:187px" %)(((
@@ -594,38 +594,38 @@
  (% class="table-bordered" %)
  |=(% colspan="4" %)**Timer interrupt mask register**
--|=(% style="width: 262px;" %)**Special register number**|=(% style="width: 309px;" %)**Type of interrupt**|=(% style="width: 394px;" %)**Instruction**|=(% style="width: 110px;" %)**Default**
--|(% style="width:262px" %)SD350|(% style="width:309px" %)1st to 16th timer interrupt|(% style="width:394px" %)(((
++|=**Special register number**|=(% style="width: 311px;" %)**Type of interrupt**|=(% style="width: 391px;" %)**Instruction**|=(% style="width: 110px;" %)**Default**
++|SD350|(% style="width:311px" %)1st to 16th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
  )))|(% style="width:110px" %)0
--|(% style="width:262px" %)SD351|(% style="width:309px" %)17th to 32th timer interrupt|(% style="width:394px" %)(((
++|SD351|(% style="width:311px" %)17th to 32th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
  )))|(% style="width:110px" %)0
--|(% style="width:262px" %)SD352|(% style="width:309px" %)33th to 48th timer interrupt|(% style="width:394px" %)(((
++|SD352|(% style="width:311px" %)33th to 48th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
  )))|(% style="width:110px" %)0
--|(% style="width:262px" %)SD353|(% style="width:309px" %)49th to 64th timer interrupt|(% style="width:394px" %)(((
++|SD353|(% style="width:311px" %)49th to 64th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
  )))|(% style="width:110px" %)0
--|(% style="width:262px" %)SD354|(% style="width:309px" %)65th to 80th timer interrupt|(% style="width:394px" %)(((
++|SD354|(% style="width:311px" %)65th to 80th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
  )))|(% style="width:110px" %)0
--|(% style="width:262px" %)SD355|(% style="width:309px" %)81st to 96th timer interrupt|(% style="width:394px" %)(((
++|SD355|(% style="width:311px" %)81st to 96th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
  )))|(% style="width:110px" %)0
--|(% style="width:262px" %)SD356|(% style="width:309px" %)97th to 100th timer interrupt|(% style="width:394px" %)(((
++|SD356|(% style="width:311px" %)97th to 100th timer interrupt|(% style="width:391px" %)(((
  Each bit can control the mask of an interrupt.
  ON: shield interrupts; OFF: interrupt allowed
@@ -702,75 +702,78 @@
  == Positioning instructions ==
--(% class="wikigeneratedid" %)
--**Event**
++      ~1. Event
--(% class="wikigeneratedid" %)
--ON event
++      1.ON event
--* If the high-speed pulse instruction is turned on during the ON event, the high-speed pulse instruction will be sent as normal. If the ON contact of the trigger event in the scan period is turned OFF during the pulse sending, select whether to continue sending the pulse or stop the pulse according to the unscanned processing flag bit.
++If the high-speed pulse instruction is turned on during the ON event, the high-speed pulse instruction will be sent as normal. If the ON contact of the trigger event in the scan period is turned OFF during the pulse sending, select whether to continue sending the pulse or stop the pulse according to the unscanned processing flag bit.
  (% class="table-bordered" %)
--|=(% scope="row" %)**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
--|=**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
++|**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
++|**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
--* When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, continue to send pulses until it stops. At this time, it should be noted that if the trigger event OFF contact turns ON after the pulse is sent, the pulse will be sent again.
--* When the flag bit is 1 (stop sending pulses), if the trigger event ON contact turns OFF in a certain scan period, it will decelerate and stop.
++When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, continue to send pulses until it stops. At this time, it should be noted that if the trigger event OFF contact turns ON after the pulse is sent, the pulse will be sent again.
-- TIME event
++When the flag bit is 1 (stop sending pulses), if the trigger event ON contact turns OFF in a certain scan period, it will decelerate and stop.
--* If the high-speed pulse instruction is turned on in the TIME event, the high-speed pulse instruction will be sent as normal. If the instruction is not scanned in a certain scan period during the pulse transmission, select whether to continue sending the pulse or stop the pulse according to the unscanned processing flag bit.
++      2. TIME event
++If the high-speed pulse instruction is turned on in the TIME event, the high-speed pulse instruction will be sent as normal. If the instruction is not scanned in a certain scan period during the pulse transmission, select whether to continue sending the pulse or stop the pulse according to the unscanned processing flag bit.
++
  (% class="table-bordered" %)
--|=(% scope="row" %)**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
--|=**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
++|**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
++|**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
--* When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, the pulse will continue to be sent until it stops. In the TIME event, it is impossible to ensure that the instruction is scanned in every scan cycle, so you should avoid using high-speed pulse instructions in the TIME time, otherwise the pulse will be sent again after the pulse is sent.
--* When the flag bit is 1 (stop sending pulses), if the instruction is not scanned in the current scan cycle, it will decelerate and stop. In the TIME event, if the flag bit is set to 1 (stop sending pulses), there will be no pulse sending.
++When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, the pulse will continue to be sent until it stops. In the TIME event, it is impossible to ensure that the instruction is scanned in every scan cycle, so you should avoid using high-speed pulse instructions in the TIME time, otherwise the pulse will be sent again after the pulse is sent.
--**Subroutine**
++When the flag bit is 1 (stop sending pulses), if the instruction is not scanned in the current scan cycle, it will decelerate and stop. In the TIME event, if the flag bit is set to 1 (stop sending pulses), there will be no pulse sending.
++       2. Subroutine
++
  If the high-speed pulse instruction is turned on in the subroutine, the high-speed pulse instruction will be sent as normal. If the scanning period is closed during pulse sending, select whether to continue sending or stop the pulse according to the unscanned processing flag.
  (% class="table-bordered" %)
--|=(% scope="row" %)**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
--|=**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
++|**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
++|**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
  When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, the pulse will continue to be sent until it stops. At this time, it should be noted that if the subroutine is called again after the pulse is sent, the pulse will be sent again.
  When the flag bit is 1 (stop sending pulses), if the subroutine is closed during high-speed pulse sending, the speed will decelerate and stop. If the subroutine is closed before sending the pulse, then no pulse is sent.
--**Interrupt**
++      3. Interrupt
--External interrupt
++1. External interrupt
--* If the high-speed pulse instruction is enabled in the external interrupt, the high-speed pulse instruction selects whether the pulse continues to be sent or the pulse stops according to the unscanned processing flag bit.
++If the high-speed pulse instruction is enabled in the external interrupt, the high-speed pulse instruction selects whether the pulse continues to be sent or the pulse stops according to the unscanned processing flag bit.
  (% class="table-bordered" %)
--|=(% scope="row" %)**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
--|=**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
++|**Output shaft**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
++|**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
--* When the flag bit is 0 (continue to send pulse), continue to send high-speed pulses until it stops.
--* When the flag bit is 1 (stop sending pulse), the high-speed pulse decelerates and stops.
++When the flag bit is 0 (continue to send pulse), continue to send high-speed pulses until it stops.
--Timer interrupt
++When the flag bit is 1 (stop sending pulse), the high-speed pulse decelerates and stops.
--* If the high-speed pulse instruction is turned on in the timer interruption, the high-speed pulse instruction is sent as normal. If the instruction is not scanned in a certain scan period in the pulse transmission, the pulse continues to be sent or the pulse stops is selected according to the unscanned processing flag.
++        2. Timer interrupt
++If the high-speed pulse instruction is turned on in the timer interruption, the high-speed pulse instruction is sent as normal. If the instruction is not scanned in a certain scan period in the pulse transmission, the pulse continues to be sent or the pulse stops is selected according to the unscanned processing flag.
++
  (% class="table-bordered" %)
--|=(% scope="row" %)**Output axis**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
--|=**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
++|**Output axis**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
++|**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
--* When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, continue to send pulses until it stops. In the timer interrupt, it is impossible to ensure that the instruction is scanned in every scan cycle, so it is necessary to avoid using high-speed pulse instructions in the T timer interrupt. Otherwise, after the pulse transmission is completed, the pulse will be sent again.
--* When the flag bit is 1 (stop sending pulses), if the instruction is not scanned in the current scan cycle, it will decelerate and stop. In the TIME event, if the flag bit is set to 1 (stop sending pulses), there will be no pulse sending.
++When the flag bit is 0 (continue to send pulse), if the instruction is not scanned in the current scan cycle, continue to send pulses until it stops. In the timer interrupt, it is impossible to ensure that the instruction is scanned in every scan cycle, so it is necessary to avoid using high-speed pulse instructions in the T timer interrupt. Otherwise, after the pulse transmission is completed, the pulse will be sent again.
--High-speed comparison interrupt
++When the flag bit is 1 (stop sending pulses), if the instruction is not scanned in the current scan cycle, it will decelerate and stop. In the TIME event, if the flag bit is set to 1 (stop sending pulses), there will be no pulse sending.
--* If the high-speed pulse instruction is enabled in the high-speed comparison interrupt, the high-speed pulse instruction selects whether the pulse continues to be sent or the pulse stops according to the unscanned processing flag.
++       3.High-speed comparison interrupt
++If the high-speed pulse instruction is enabled in the high-speed comparison interrupt, the high-speed pulse instruction selects whether the pulse continues to be sent or the pulse stops according to the unscanned processing flag.
++
  (% class="table-bordered" %)
--|=(% scope="row" %)**Output axis**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
--|=**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
++|**Output axis**|Y0|Y1|Y2|Y3|Y4|Y5|Y6|Y7
++|**Not scanned flag bit**|SM899|SM959|SM1019|SM1079|SM1139|SM1199|SM1259|SM1319
--* When the flag bit is 0 (continue to send pulse), continue to send high-speed pulses until it stops.
--* When the flag bit is 1 (stop sending pulse), the high-speed pulse decelerates and stops.
++When the flag bit is 0 (continue to send pulse), continue to send high-speed pulses until it stops.
++
++When the flag bit is 1 (stop sending pulse), the high-speed pulse decelerates and stops.

image-20220926104203-1.jpeg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Stone

Size

...	...	@@ -1,1 +1,0 @@
1		-105.7 KB

Content

Changes for page 01 Program execution

Summary

Details

Navigation

Table of Contents