12 - Wecon

1

= **Contact comparison instruction** =

2

3

== **Signed 16-bit contact comparison instruction** ==

4

5

**LD £, AND £, OR £**

6

7

The BIN 16-bit data of the device specified in (s1) and the BIN 16-bit data of the device specified in (s2) are compared by normal open contact processing.

8

9

LD£: Normally open contact comparison instruction

10

11

AND£: Normally open contact series connection comparison instruction

12

13

OR£: Normally open contact parallel connection comparison instruction

**Ladder diagram**

(% style="text-align:center" %)

18

[[image:07-5 Basic instructions_html_63210db6b7e1512f.png]]

19

20

(You can enter "=", "<>", ">", "<", ">=", "<=" in "£")

21

22

**Content, range and data type**

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="11" %)**Devices**|(((

31

**Offset modification**

)))|(((

**Pulse extension**

)))

|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**K**|**H**|**[D]**|**XXP**

36

|LD=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

37

|LD>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

38

|LD<|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

39

|LD>=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

40

|LD<=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

41

|LD<>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

42

|AND=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

43

|AND>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

44

|AND<|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

45

|AND>=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

46

|AND<=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

47

|AND<>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

48

|OR=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

49

|OR>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

50

|OR<|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

51

|OR>=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

52

|OR<=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

53

|OR<>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|

**Features**

The BIN 16-bit data of the device specified in (s1) and the BIN 16-bit data of the device specified in (s2) are compared by normal open contact processing.

58

59

The comparison operation result of each instruction is shown below.

60

61

62

|==|(s1)=(s2)|(% rowspan="6" %)On state|==|(s1)≠(s2)|(% rowspan="6" %)Non-conduction state

63

|<>|(s1)≠(s2)|<>|(s1)=(s2)

64

|>|(s1)>(s2)|>|(s1)≤(s2)

65

|<|(s1)<(s2)|<|(s1)≥(s2)

66

|>=|(s1)≥(s2)|>=|(s1)<(s2)

67

|<=|(s1)≤(s2)|<=|(s1)>(s2)

**Error code**

|**Error code**|**Content**

72

|4085H|(s) read address exceeds the device range

**Example**

(((

(1) When the current value of counter C10 is 200, Y10 is set

78

79

When the content of D200 is above -29, and X1 is ON, Y11 is set

LD£ instruction:

(% style="text-align:center" %)

84

[[image:07-5 Basic instructions_html_1309199eccc7134.png]]

)))

(2) AND£ instruction

(((

When X0 is ON, or when the current value of counter C10 is 200, Y10 is set

91

92

When X1 is OFF, and the content of data counter D0 is not -10, Y11 is set

93

94

(% style="text-align:center" %)

95

[[image:07-5 Basic instructions_html_1c966f74b0bd808e.png]]

)))

(3) OR£ instruction:

(((

When X1 is ON, or when the current value of counter C10 is 200, Y0 is set

104

105

When X2 and M30 are ON, or the content of register D100 is K10000 and above, M60 is set

106

107

(% style="text-align:center" %)

108

[[image:07-5 Basic instructions_html_8b000809015ea436.png]]

109

)))

110

111

== **Signed 32-bit contact comparison instruction** ==

112

113

**LDD £, ANDD £, ORD £**

114

115

The BIN 32-bit data of the device specified in (s1) and the BIN 32-bit data of the device specified in (s2) are compared by normal open contact processing.

116

117

LDD£: Normally open contact comparison command

118

119

ANDD£: Normally open contact series link comparison instruction

120

121

ORD£: Normally open contact parallel link comparison instruction

**Ladder diagram**

(% style="text-align:center" %)

126

[[image:07-5 Basic instructions_html_63210db6b7e1512f.png]]

127

128

“=”, “<>”, “>”, “<”, “>=”, “<=” can be input in “£”

129

130

**Content, range and data type**

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="14" %)**Devices**|(((

139

**Offset modification**

)))|(((

**Pulse extension**

)))

|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

144

|LDD=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

145

|LDD>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

146

|LDD<|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

147

|LDD>=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

148

|LDD<=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

149

|LDD<>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

150

|ANDD=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

151

|ANDD>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

152

|ANDD<|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

153

|ANDD>=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

154

|ANDD<=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

155

|ANDD<>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

156

|ORD=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

157

|ORD>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

158

|ORD<|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

159

|ORD>=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

160

|ORD<=|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

161

|ORD<>|s1, s2|●|●|●|●|●|●|●|●|●|●|●|●|●| |●|

**Features**

The BIN 32-bit data of the device specified in (s1) and the BIN 32-bit data of the device specified in (s2) are compared by normal open contact processing.

166

167

The comparison operation result of each instruction is shown below.

168

169

170

|==|(s1)=(s2)|(% rowspan="6" %)On state|==|(s1)≠(s2)|(% rowspan="6" %)Non-conduction state

171

|<>|(s1)≠(s2)|<>|(s1)=(s2)

172

|>|(s1)>(s2)|>|(s1)≤(s2)

173

|<|(s1)＜(s2)|<|(s1)≥(s2)

174

|>=|(s1)≥(s2)|>=|(s1)＜(s2)

175

|<=|(s1)≤(s2)|<=|(s1)>(s2)

**Error code**

|**Error code**|**Content**

180

|4085H|(S) read address exceeds the device range

**Example**

(1) LDD£ instruction:

185

186

When the data of LC10 is 200000, Y10 is set, otherwise Y10 is reset.

187

188

When the 32-bit data composed of D201 and D200 exceeds -5000, and X1 is ON, Y11 is turned ON.

189

190

1. ANDD£ instruction:

191

192

[[image:07-5 Basic instructions_html_38be93eec0ced6c.png]]

193

194

When X0 is ON and the value of LC10 is 200000, Y10 is set, otherwise it is reset.

195

196

When X1 is OFF and the 32-bit data composed of D1 and D0 is not equal to K-50000, Y11 is set.

1. ORD£ instruction:

[[image:07-5 Basic instructions_html_8ebfc7b0562cf370.png]]

201

202

When X1 is ON, or the data of LC10 is equal to the data of LC10 is equal to 200000, Y0 is set.

203

204

When X2 and M30 are set, or the double word data composed of D101 and D100 is greater than or equal to 100000, M60 is set.

205

206

{{id name="_Toc28789"/}}{{id name="_Toc29577"/}}**Single precision real number contact comparison instruction**

207

208

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **LDE £, ANDE £, ORE £**

209

210

The single precision real number of the device specified in (s1) and the single precision real number of the device specified in (s2) are compared by normal open contact processing.

211

212

LDE□: Normally open contact comparison command

213

214

ANDE□: Normally open contact series link comparison instruction

215

216

ORE□: Normally open contact parallel link comparison instruction

**Ladder diagram**

[[image:07-5 Basic instructions_html_6ac28f30e24ad296.png]]

221

222

“=”, “<>”, “>”, “<”, “>=”, “<=” can be input in “£”

223

224

**Content, range and data type**

225

226

227

|(s1)|{{id name="OLE_LINK28"/}}Comparison data or the device start number storing the comparison data|{{id name="OLE_LINK339"/}}0, 2^^-126^^ ≤~|(s)~|< 2^^128^^|Single precision real number|ANYREAL_32

228

|(s2)|Comparison data or the device start number storing the comparison data|0, 2^^-126^^ ≤~|(s)~|< 2^^128^^|Single precision real number|ANYREAL_32

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

242

|LDE=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

243

|LDE>|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

244

|LDE<|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

245

|LDE>=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

246

|LDE<=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

247

|LDE<>|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

248

|ANDE=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

249

|ANDE>|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

250

|ANDE<|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

251

|ANDE>=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

252

|ANDE<=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

253

|ANDE<>|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

254

|ORE=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

255

|ORD>|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

256

|ORE<|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

257

|ORE>=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

258

|ORE<=|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

259

|ORE<>|s1, s2| | | | | | | | | | | | | | |●|●|●|●|●|●|●| | |●|●|

**Features**

The single precision real number of the device specified in (s1) and the single precision real number of the device specified in (s2) are compared by normal open contact processing.

264

265

The comparison operation result of each instruction is shown below.

266

267

268

|E=|(s1)=(s2)|(% rowspan="6" %)On state|E=|(s1)≠(s2)|(% rowspan="6" %)Non-conduction state

269

|E<>|(s1)≠(s2)|E<>|(s1)=(s2)

270

|E>|(s1)>(s2)|E>|(s1)≤(s2)

271

|E<|(s1)＜(s2)|E<|(s1)≥(s2)

272

|E>=|(s1)≥(s2)|E>=|(s1)＜(s2)

273

|E<=|(s1)≤(s2)|E<=|(s1)>(s2)

**Error code**

|**Error code**|**Content**

278

|4084H|{{id name="OLE_LINK340"/}}When the content of the specified device by (s1) and (s2) is an irregular number, a non-number, or ±∞

279

|4085H|{{id name="OLE_LINK343"/}}The read address of (s1) and (s2exceeds the device range

**Example**

1. LDE£ instruction:

[[image:07-5 Basic instructions_html_c4c820cf59601493.png]]

286

287

When the real number input in D0 is equal to E1.23, Y10 is ON, otherwise Y10 is OFF.

288

289

When the real number in R0 is greater than or equal to the real number in LC0, Y11 is ON, otherwise it is OFF.

290

291

If the input in D0, R0, LC0 is not a real number, it will report H4084 error.

292

293

1. ANDE£ instruction:

294

295

[[image:07-5 Basic instructions_html_7cdd2117360e179b.png]]

296

297

Only when M0 is ON and D2 real number is not equal to E1.23 and R2 real number is less than real number LC2 , Y12 is ON, otherwise all are OFF.

1. ORE£ instruction:

[[image:07-5 Basic instructions_html_3eba0bd56176441d.png]]

302

303

When the real number of R4 is less than or equal to the real number of R15, or the real number R6 is equal to the real number R20, Y13 is ON, otherwise Y13 is OFF.

304

305

{{id name="_Toc16295"/}}{{id name="_Toc20251"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **String comparison**

**LDS£、ANDS£、 ORS£**

{{id name="OLE_LINK27"/}}Compare the string stored after the device number specified in (s1) with the string stored after the device number specified in (s2).

310

311

LDS£: String comparison instruction

312

313

ANDS£: String serial connection comparison instruction

314

315

{{id name="OLE_LINK341"/}}ORS£: String parallel connection comparison instruction

**Ladder diagram**

[[image:07-5 Basic instructions_html_5fb3b3b70645fef5.png]]

320

321

“=” and “<>” could be entered in “£”

322

323

**Content, range and data type**

324

325

326

|(S1)|{{id name="OLE_LINK342"/}}Connection data or the device start number storing the data or the string specified directly|-|String|ANYSTRING_SINGLE

327

|(S1)|Connection data or the device start number storing the data or the string specified directly|-|{{id name="OLE_LINK29"/}}String|ANYSTRING_SINGLE

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

341

|LDS=|s1、s2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|

342

|LDS<>|s1、s2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|

343

|ANDS=|s1、s2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|

344

|ANDS<>|s1、s2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|

345

|ORS=|s1、s2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|

346

|ORS<>|s1、s2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|

**Features**

• Compare the string stored after the device number specified in (s1) with the string stored after the device number specified in (s2).

351

352

• The comparison operation result of each instruction is shown below.

353

354

355

|= |(s1)＝(s2)|(% rowspan="2" %)On stat|= |(s1)≠(s2)|(% rowspan="2" %)Non-conduction state

356

|<>|(s1)≠(s2)|<>|(s1)＝(s2)

**Error code**

|**Error code**|**Content**

361

|4085H|The read address of (s1) or (s2) exceeds the device range

362

|408AH|The length of the read string of (s1) or (s2) exceeds, and the continuous length of the string exceeds 400 characters.

363

|408BH|When (s1) or (s2) reading the string, the maximum range of the device is read but 00H is not found as the end.

**Example**

1. 1、LDS£ instruction

368

369

[[image:07-5 Basic instructions_html_449a071f61ff5b58.png]]

1. ANDS£ instruction

[[image:07-5 Basic instructions_html_dd6aa995d193bdd2.png]]

1. ORS£ instruction

[[image:07-5 Basic instructions_html_4f8fb7c94f87c58d.png]]

378

379

{{id name="_Toc11737"/}}[[image:07-5 Basic instructions_html_a2e3294e01b2f206.gif]] **7.12 Clock operation instruction**

380

381

{{id name="_Toc9100"/}}{{id name="_Toc26958"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **TADD/The addition of clock data**

**TADD(P)**

Add the time data stored after the device number specified in (s1) and the time data stored after the device number specified in (s2), and store the result of the addition operation after the device number specified in (d) .

386

387

-[TADD (s1) (s2) (d)]

388

389

**Content, range and data type**

390

391

392

|(s1)|{{id name="OLE_LINK345"/}}The device start number that stores the added time data|-|Signed BIN 16 bit|(((

393

ANY16_ARRAY

394

395

(number of elements: 3)

396

)))

397

|(s2)|The device start number that stores the addition operation time (time) data|-|Signed BIN 16 bit|(((

398

ANY16_ARRAY

399

400

(number of elements: 3)

401

)))

402

|(d)|The device start number that stores the time (time) data of the addition operation result|-|Signed BIN 16 bit|(((

403

ANY16_ARRAY

404

405

(number of elements: 3)

)))

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

420

|(% rowspan="3" %)TADD|Parameter 1| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

421

|Parameter 2| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

422

|Parameter 3| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

**Features**

Add the time data specified in (s1) and the time data specified in (s2), and store the result of the addition in the device number specified in (d) or later.

427

428

[[image:07-5 Basic instructions_html_37222a6e282347f9.png]]

**Example**

When 6:32:40 and 7:48:10 are added together

433

434

[[image:07-5 Basic instructions_html_90138670198ab422.png]]

435

436

When the calculation result time exceeds 24 o'clock, the carry flag turns ON, and the value after 24 hours is subtracted becomes the calculation result. For example, when 14:20:30 and 20:20:20 are added, the result is not 34:40:50, but 10:40:50.

437

438

[[image:07-5 Basic instructions_html_bac419ce2dc0dc2.png]]

439

440

When the calculation result is 0 (0 hour, 0 minute, 0 second), the zero flag turns on.

441

442

When 23:59:59 and 1 second are added, the result of the calculation is 0:00:00, and the carry flag and zero flag are turned on.

443

444

Related device are as follows:

445

446

|**Devices**|**Name**|**Content**

447

|SM151|Carry|It is ON when the result of the TADD(P) instruction exceeds the maximum clock data value of 23:59:59

448

|SM153|Zero|It is ON when the result of the TADD(P) instruction is 0:00:00

✎**Note**

The devices specified in (s1), (s2), (d) occupy 3 points respectively. Be careful not to overlap with the device used for machine control.

453

454

When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.

**Error code**

|**Error code**|**Content**

459

|4085H|{{id name="OLE_LINK344"/}}When reading the specified device range exceeds the corresponding device range

460

|4086H|When writing the specified device range exceeds the corresponding device range

461

|4084H|(((

462

When the values specified in (s1) and (s2) are other than 0 to 23

463

464

When the values specified in (s1)+1, (s2)+1, (s1)+2 and (s2)+2 are other than 0 to 59

)))

**Example**

[[image:07-5 Basic instructions_html_4f75eedee7172bbb.png]]

470

471

Set D0 time to 16:30:00 and D10 time to 4:30:0

472

473

[[image:07-5 Basic instructions_html_c64e0faf2af172f8.png]]

474

475

[[image:07-5 Basic instructions_html_66e3a2eadeb2ecbb.png]]

476

477

After the coil is turned on, the D20 time is 21:0:0

478

479

[[image:07-5 Basic instructions_html_a9b235835aa41200.png]]

{{id name="_Toc6604"/}}{{id name="_Toc16422"/}}**TSUB/The subtraction of clock data**

484

485

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **TSUB(P)**

486

487

Subtract the time data stored after the device number specified in (s1) and the time data stored after the device number specified in (s2), and store the subtraction result in the device number specified in (d) or later .

488

489

-[TSUB (s1) (s2) (d)]

490

491

**Content, range and data type**

492

493

494

|(s1)|The device start number that stores the subtracted time data|-|Signed BIN 16 bit|(((

495

ANY16_ARRAY

496

497

(number of elements: 3)

498

)))

499

|(s2)|The device start number that stores the subtraction operation time (time) data|-|Signed BIN 16 bit|(((

500

ANY16_ARRAY

501

502

(number of elements: 3)

503

)))

504

|(d)|The device start number that stores the time (time) data of the subtraction result|-|Signed BIN 16 bit|(((

505

ANY16_ARRAY

506

507

(number of elements: 3)

)))

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

522

|(% rowspan="3" %)TSUB|Parameter 1| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

523

|Parameter 2| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

524

|Parameter 3| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

**Features**

Subtract the time data specified in (s1) and the time data specified in (s2), and store the subtraction result in the device number specified in (d) or later.

529

530

[[image:07-5 Basic instructions_html_5a93455e4cd8a27.png]]

**Example**

When subtracting 10:40:20 and 3:50:10

535

536

[[image:07-5 Basic instructions_html_2473f03fc493780c.png]]

537

538

When the calculation result time is a negative number, the borrow flag turns on and the data +24 is the calculation result. For example, in the case of subtracting 4:50:32 and 10:42:12, the result is not -6:8:20, but 18:8:20.

539

540

[[image:07-5 Basic instructions_html_24b998b4c3c4ec73.png]]

541

542

When the calculation result is 0 (0 hour, 0 minute, 0 second), the zero flag turns on.

543

544

Related device are as follows:

545

546

|**Devices**|**Name**|**Content**

547

|SM152|Borrow|It is ON when the result of the TSUB(P) instruction is less than 0:00:00

548

|SM153|Zero|It is ON when the result of the TSUB(P) instruction is at the time of 0:00:00:00

✎**Note**

• The devices specified in (s1), (s2), and (d) occupy 3 points respectively. Be careful not to overlap with the device used for machine control.

553

554

• When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.

**Error code**

|**Error code**|**Content**

559

|4085H|When reading the specified device range exceeds the corresponding device range

560

|4086H|When writing the specified device range exceeds the corresponding device range

561

|4084H|(((

562

When the values specified in (s1) and (s2) are other than 0 to 23

563

564

When the values specified in (s1)+1, (s2)+1, (s1)+2 and (s2)+2 are other than 0 to 59

)))

**Example**

[[image:07-5 Basic instructions_html_e3a5d4793d3ccd2d.png]]

570

571

Set D0 time to 16:30:00 and D10 time to 4:30:0

572

573

[[image:07-5 Basic instructions_html_c64e0faf2af172f8.png]]

574

575

[[image:07-5 Basic instructions_html_66e3a2eadeb2ecbb.png]]

576

577

After the coil is turned on, the D20 time is 12:00:00

578

579

[[image:07-5 Basic instructions_html_8f93ea19ba10652b.png]]

580

581

{{id name="_Toc10358"/}}{{id name="_Toc12073"/}}[[image:07-5 Basic instructions_html_501fb256fd034ca6.gif]] **TRD/Clock data reading**

**TRD(P)**

Read the clock data of the built-in real-time clock of the CPU module.

-[TRD (d)]

**Content, range and data type**

590

591

592

|(d)|Read destination and start device number of clock data|-|Signed BIN 16 bit|(((

593

ANY16_ARRAY

594

595

(number of elements: 7)

)))

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

610

|TRD|Parameter 1| | | | | | | | | | | | | | |●|●|●|●| | | | | | |●|●

**Features**

Read the clock data (SD100 to SD106) of the real-time clock built into the CPU module into (d) to (d)+6 in the following format.

615

616

617

|(% rowspan="7" %)Special register|SD105|Year (Gregorian)|2000 to 2099|→|(d)|Year (Gregorian)

618

|SD104|Month|1 to 12|→|(d)+1|Month

619

|SD103|Day|1 to 31|→|(d)+2|Day

620

|SD102|Hour|0 to 23|→|(d)+3|Hour

621

|SD101|Minute|0 to 59|→|(d)+4|Minute

622

|SD100|Seconds|0 to 59|→|(d)+5|Seconds

623

|SD106|Week|0 (Sun) to 6 (Sat)|→|(d)+6|Week

624

625

• The related devices are shown below. The clock data of these special registers are updated through END processing.

626

627

|**Devices**|**Content**

628

|SD100|The second data of the clock data is stored in BIN code.

629

|SD101|The sub-data of the clock data is stored in BIN code.

630

|SD102|Time data of clock data is stored in BIN code.

631

|SD103|The daily data of the clock data is stored in BIN code.

632

|SD104|The monthly data of the clock data is stored in BIN code.

633

|SD105|The year data of the clock data is stored in a 4-digit BIN code of the Gregorian calendar.

634

|SD106|The week data of the clock data is stored in BIN code. (0: day, 1: one, ..., 6: six) are stored in BIN code.

✎**Note**

• The device specified in (d) occupies 7 points. Be careful not to overlap with the device used for machine control.

**Error code**

|**Error code**|**Content**

643

|4086H|When reading the specified device range exceeds the corresponding device range

**Example**

[[image:07-5 Basic instructions_html_b81c1991fec5b4b1.png]]

648

649

After the M0 coil is turned on, the current date and time are read as 2020-2-19 13:10:38 Wednesday

650

651

[[image:07-5 Basic instructions_html_fe82ecd18ebfd787.png]]

652

653

{{id name="_Toc24237"/}}{{id name="_Toc487"/}}**TWR/Clock data writing**

654

655

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **TWR(P)**

656

657

Write the clock data of the built-in real-time clock of the CPU module.

-[TWR (s)]

**Content, range and data type**

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

678

|TWR|Parameter 1| | | | | | | | | | | | | | |●|●|●|●| | | | | | |●|●

**Features**

Write the set clock data (s) to (s)+6 to the clock data (SD100 to SD106) of the real-time clock built into the CPU module.

683

684

|(% colspan="3" %)**Set data at all times**|(% rowspan="2" %) |(% colspan="2" %)**Special register**

685

686

|(s)|Year (Gregorian)|2000 to 2099 or 0 to 99|→|SD105|Year (Gregorian)

687

|(s)+1|Month|1 to 12|→|SD104|Month

688

|(s)+2|Day|1 to 31|→|SD103|Day

689

|(s)+3|Hour|0 to 23|→|SD102|Hour

690

|(s)+4|Minute|0 to 59|→|SD101|Minute

691

|(s)+5|Seconds|0 to 59|→|SD100|Seconds

692

|(s)+6|Week|0 (Sun) to 6 (Sat)|→|SD106|Week

693

694

• If the TWR(P) instruction is executed, the clock data of the real-time clock is changed immediately. Therefore, the clock data after a few minutes should be transferred to the set clock data (s) to (s)+6 in advance, and the instruction will be executed when the correct time is reached.

695

696

• If the year in (s) is in the range of 0 to 99, it will be automatically treated as 2000 to 2099.

697

698

• When a value indicating an impossible time is set, the clock data will not be updated. Set the correct clock data and write again.

699

700

• The day of the week (SD100) is automatically corrected.

701

702

• The related devices are shown below.

703

704

|**Devices**|**Content**

705

|SD100|The second data of the clock data is stored in BIN code.

706

|SD101|The sub-data of the clock data is stored in BIN code.

707

|SD102|Time data of clock data is stored in BIN code.

708

|SD103|The daily data of the clock data is stored in BIN code.

709

|SD104|The monthly data of the clock data is stored in BIN code.

710

|SD105|The year data of the clock data is stored in a 4-digit BIN code of the Gregorian calendar.

711

|SD106|The week data of the clock data is stored in BIN code. (0: day, 1: one, ..., 6: six) are stored in BIN code.

✎**Note**

The device specified in (s) occupies 7 points. Be careful not to overlap with the device used for machine control.

**Error code**

|**Error code**|**Content**

720

|4085H|When reading the specified device range exceeds the corresponding device range

**Example**

Set D0 date and time to 2020-2-19 12:36:00 in advance

725

726

[[image:07-5 Basic instructions_html_994c66d1a4cbd45f.png]]

727

728

At the moment when the time 12:36:00 arrives, turn on the M0 coil and write the time.

729

730

[[image:07-5 Basic instructions_html_bf3e906ee5265598.png]]

731

732

{{id name="_Toc5357"/}}{{id name="_Toc6196"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **HTOS/16-bit data conversion of time data (hour, minute, second → second)**

**HTOS(P)**

Convert the time data stored after the device number specified in (s) into seconds and store the conversion result as BIN 16-bit data in the device specified in (d).

-[HTOS (s) (d)]

**Content, range and data type**

|(d)|The device start number that stores the converted clock data|-|Signed BIN 16 bit|ANY16

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

754

|(% rowspan="2" %)HTOS|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

755

|Parameter 2| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

Convert the time data stored after the device number specified in (s) into seconds and store the conversion result in the device specified in (d).

760

761

[[image:07-5 Basic instructions_html_a84b7741fd5bef2f.png]]

**Example**

When 4 hours, 29 minutes and 31 seconds are specified in (s)

766

767

[[image:07-5 Basic instructions_html_5effb7bc9b8e5cf7.png]]

**Error code**

|**Error code**|**Content**

772

|4085H|When reading the specified device range exceeds the corresponding device range

773

|4086H|When writing the specified device range exceeds the corresponding device range

774

|4084H|(((

775

{{id name="OLE_LINK348"/}}When the calculation result is not in the range of 0 to 32767

776

777

When the value specified in (s) is not in the range of 0 to 9

778

779

When the value specified in (s)+1 and (s)+2 is not in the range of 0 to 59

)))

**Example**

[[image:07-5 Basic instructions_html_e23e38c4ba4c34bb.png]]

785

786

D0 time is set to 5:36:53

787

788

[[image:07-5 Basic instructions_html_2866a121e5ca5713.png]]

789

790

The time of D10 after the M0 coil is turned on is as below.

791

792

[[image:07-5 Basic instructions_html_1dd6c5de05890797.png]]

793

794

{{id name="_Toc13431"/}}{{id name="_Toc5278"/}}**DHTOS/32-bit data conversion of time data (hour, minute, second → second)**

795

796

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DHTOS(P)**

797

798

Convert the time data stored after the device number specified in (s) into seconds and store the conversion result as BIN 32-bit data in the device specified in (d).

-[DHTOS (s) (d)]

**Content, range and data type**

|(d)|The device start number that stores the converted clock data|-|Signed BIN 32 bit|ANY32

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

820

|(% rowspan="2" %)DHTOS|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

821

|Parameter 2| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

Convert the time data stored after the device number specified in (s) into seconds and store the conversion result in the device specified in (d).

826

827

[[image:07-5 Basic instructions_html_f4be08508575ea01.png]]

**Example**

When 35 hours, 10 minutes and 58 seconds are specified in (s)

832

833

[[image:07-5 Basic instructions_html_5b9ad230ed5e1fd0.png]]

**Error code**

|**Error code**|**Content**

838

|4085H|When reading the specified device range exceeds the corresponding device range

839

|4086H|When writing the specified device range exceeds the corresponding device range

840

|4084H|(((

841

When the calculation result is not in the range of 0 to 32767

842

843

When the value specified in (s)+1 and (s)+2 is not in the range of 0 to 59

)))

**Example**

[[image:07-5 Basic instructions_html_ae8ab4379e8bdb91.png]]

849

850

D0 time is set to 15:33:24

851

852

[[image:07-5 Basic instructions_html_57a15d9e1045e93e.png]]

853

854

The second of D10 after the M0 coil is turned on is

855

856

[[image:07-5 Basic instructions_html_194e906b1dc12078.png]]

857

858

{{id name="_Ref22686"/}}{{id name="_Toc11231"/}}{{id name="_Toc7401"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **HOUR/Hour measuring 16-bit**

**HOUR(P)**

The time for the input contact to be ON is measured in units of one hour.C

863

864

-[HOUR (s) (d1) (d2)]

865

866

**Content, range and data type**

|(s)|(((

The time when the alarm (d2) is turned ON

871

872

(set by one hour)

873

)))|K0 to K32767|Signed BIN 16 bit|ANY16

874

|(d1)|Device that stores the current value of measurement (specified data register for power failure retention)|-|Unsigned BIN 16 bit|(((

875

ANY16_ARRAY

876

877

(Number of elements: 2)

878

)))

879

|(d2)|Device that turns ON when the time limit expires (alarm output)|-|Bit|ANY_BOOL

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

893

|(% rowspan="3" %)HOUR|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

894

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

895

|Parameter 3| |●|●|●|●| | | | |●| | | | | | | | | | | | | | |●|●

**Features**

The input contact ON time is measured in units of 1 hour. When the cumulative ON time exceeds the time (BIN 16-bit data) specified in (s), the device specified in (d2) is turned on .

900

901

• In (s), set the time until the alarm (d2) turns ON in units of 1 hour.

902

903

• (d1) stores the current measured value in units of 1 hour.

904

905

• If the median value of (d1) exceeds 32767, it will be modified to 32767.

906

907

• (d1)+1 stores the current measured value (in units of 1 second) that is less than 1 hour.

908

909

• (d2) turns on when the current value (d1) exceeds the time specified in (s).

910

911

• In order to continue to use the current value data even after the power of the CPU module is turned off, specify the data register for power failure retention to (d1). If you use general-purpose data registers, the current value data will be cleared by powering off the CPU module and STOP→RUN operations.

912

913

• After the alarm output specified in (d2) turns ON, measurement will continue.

914

915

• The measurement stops when the current value reaches the 16-bit maximum. To continue the measurement, clear the current value of (d1) to (d1)+1.

✎**Note**

• The device specified in (d1) occupies 2 points. Be careful not to overlap with the device used for machine control.

920

921

• After the instruction stops running, the measurement stops and the output continues to be maintained.

**Error code**

|**Error code**|**Content**

926

|4085H|When reading the specified device range exceeds the corresponding device range

927

|4086H|When writing the specified device range exceeds the corresponding device range

928

|4084H|When the value of (s) is negative

**Example**

[[image:07-5 Basic instructions_html_7570f8c392470a9f.png]]

935

936

When M0 = ON, the duration of the state is accumulated, the time is recorded in D0, and the seconds less than 1 hour are recorded in D1. When the accumulated time of D0 reaches 98 hours, the Y0 output state is ON. When the timing conditions are met, after reaching the specified value (K98), the accumulated timing will continue and the reading will continue to increase; the current time value D0 reaches the maximum value of 32767 hours and D1 reaches 3599 seconds, the timing measurement will stop. The current time values D0 and D1 are cleared to 0.

937

938

{{id name="_Toc8523"/}}{{id name="_Toc9364"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DHOUR/Hour measuring 32 bits**

**DHOUR(P)**

The time for the input contact to be ON is measured in units of one hour.

943

944

-[DHOUR (s) (d1) (d2)]

945

946

**Content, range and data type**

|(s)|(((

The time when the alarm (d2) is turned ON

951

952

(set by one hour)

953

)))|0 to 2147483647|Signed BIN 32 bit|ANY32

954

|(d1)|Device that stores the current value of measurement (specified data register for power failure retention)|-|Unsigned BIN 32 bit|(((

955

ANY32_ARRAY

956

957

(Number of elements: 2)

958

)))

959

|(d2)|Device that turns ON when the time limit expires (alarm output)|-|Bit|ANY_BOOL

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

973

|(% rowspan="3" %)DHOUR|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

974

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

975

|Parameter 3| |●|●|●|●| | | | |●| | | | | | | | | | | | | | |●|●

**Features**

• The input contact ON time is measured in units of 1 hour. When the cumulative ON time exceeds the time (BIN 32-bit data) specified in (s), the device specified in (d2) is set to ON.

980

981

• In (s)+1, (s), set the time until the alarm (d2) turns ON in units of 1 hour.

982

983

• (D1)+1 and (d1) store the current value measured in units of 1 hour. ((d1)+1: high bit, (d1): low bit)

984

985

• If the median of (d1)+1 and (d1) exceeds 2147483647, it will be modified to 2147483647.

986

987

• (D1)+2 stores the current value (in units of 1 second) of the measurement that is less than 1 hour.

988

989

• (D2) turns on when the current value (d1)+1, (d1) exceeds the time specified in (s).

990

991

• In order to continue to use the current value data even after the power of the CPU module is turned off, specify the data register for power failure retention to (d1). If you use general-purpose data registers, the current value data will be cleared by powering off the CPU module and STOP→RUN operations.

992

993

• After the alarm output specified in (d2) turns on, the measurement will continue.

994

995

• The measurement stops when the current value reaches the 32-bit maximum. To continue the measurement, clear the current value of (d1) to (d1)+2.

✎**Note**

• The device specified in (d1) occupies 3 points. Be careful not to overlap with the device used for machine control.

1000

1001

• After the instruction stops running, the measurement stops and the output continues to be maintained.

**Error code**

|**Error code**|**Content**

1006

|4085H|When reading the specified device range exceeds the corresponding device range

1007

|4086H|When writing the specified device range exceeds the corresponding device range

1008

|4084H|When the value of (s) is negative

**Example**

[[image:07-5 Basic instructions_html_3f1ef5ecc835de30.png]]

1015

1016

When M0=ON, the duration of this state is accumulated, the time is recorded in D1, D0, and the seconds less than 1 hour are recorded in D2. When the accumulated time of D1, D0 reaches 1000 hours, the Y0 output state is ON. When the timing conditions are met, after reaching the specified value (K1000), the accumulated timing will continue, and the reading will continue to increase; the current time values D1 and D0 reach the maximum value of 2147483647 hours, and when D2 reaches 3599 seconds, the timing measurement will stop and the timing should be restarted. The current time values D0, D1, and D2 must be cleared to 0.

1017

1018

**{{id name="_Toc11629"/}}STOH/16-bit data conversion of time data (second → hour, minute, second)**

1019

1020

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **STOH(P)**

1021

1022

Convert the second 16-bit data stored in the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.

-[STOH (s) (d)]

**Content, range and data type**

1027

1028

1029

|(s)|{{id name="OLE_LINK353"/}}The device start number that stores the clock data before conversion|0 to 32767|Signed BIN 16 bit|ANY16

1030

|(d)|The device start number that stores the converted clock data|-|Signed BIN 16 bit|(((

1031

ANY16_ARRAY

1032

1033

(number of elements: 3)

)))

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1048

|(% rowspan="2" %)STOH|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

1049

|Parameter 2| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

Convert the second data stored after the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.

1054

1055

[[image:07-5 Basic instructions_html_1f5f3f1d80af2a34.png]]

**Example**

When 29,011 seconds are specified in (s)

1060

1061

[[image:07-5 Basic instructions_html_682516cbf773f515.png]]

**Error code**

|**Error code**|**Content**

1066

|4085H|When reading the specified device range exceeds the corresponding device range

1067

|4086H|When writing the specified device range exceeds the corresponding device range

1068

|4084H|When the value of (s) exceeds the range

**Example**

[[image:07-5 Basic instructions_html_e783349d57adf7d2.png]]

1073

1074

Set D0 seconds to 12537

1075

1076

The hour, minute and second of D10 after the M0 coil is turned on are

1077

1078

[[image:07-5 Basic instructions_html_d3c33949e8684891.png]]

1079

1080

{{id name="_Toc10764"/}}{{id name="_Toc30243"/}}**DSTOH/32-bit data conversion of time data (second → hour, minute, second)**

1081

1082

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DSTOH(P)**

1083

1084

Convert the second 32-bit data of second stored in the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.

-[DSTOH (s) (d)]

**Content, range and data type**

1089

1090

1091

|(s)|The device start number that stores the clock data before conversion|0 to 117964799|Signed BIN 32 bit|ANY32

1092

|(d)|The device start number that stores the converted clock data|-|Signed BIN 16 bit|(((

1093

ANY16_ARRAY

1094

1095

(number of elements: 3)

)))

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1110

|(% rowspan="2" %)DSTOH|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

1111

|Parameter 2| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

Convert the second data stored after the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.

1116

1117

[[image:07-5 Basic instructions_html_cbf13fc3d10fbe61.png]]

**Example**

When 45,325 seconds is specified in (s)

1122

1123

[[image:07-5 Basic instructions_html_d6045506b13275a0.png]]

**Error code**

|**Error code**|**Content**

1128

|4085H|When reading the specified device range exceeds the corresponding device range

1129

|4086H|When writing the specified device range exceeds the corresponding device range

1130

|4084H|When the value of (s) exceeds the range

**Example**

[[image:07-5 Basic instructions_html_e7dd49d953db6da4.png]]

1135

1136

Set D0 seconds to 2152537

1137

1138

The hour, minute and second of D10 after the M0 coil is turned on are

1139

1140

[[image:07-5 Basic instructions_html_10d57bde1ac0a218.png]]

1141

1142

{{id name="_Toc2937"/}}{{id name="_Toc24209"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **TCMP/Clock data comparison**

**TCMP(P)**

Compare the comparison time specified in (s1), (s2), (s3) with the time data specified in (s4), and turn the bit device specified in (d) ON/OFF according to their size match.

1147

1148

-[TCMP (s1) (s2) (s3) (s4) (d)]

1149

1150

**Content, range and data type**

1151

1152

1153

|(s1)|Specify the "hour" of the comparison base time.|0 to 23|Signed BIN 16 bit|ANY16

1154

|(s2)|Specify the "minute" of the comparison base time.|0 to 59|Signed BIN 16 bit|ANY16

1155

|(s3)|Specify the "second" of the comparison base time.|0 to 59|Signed BIN 16 bit|ANY16

1156

1157

|(d)|The bit device is turned ON/OFF according to the comparison result.|-|Bit|ANYBIT_ARRAY

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1171

|(% rowspan="5" %)TCMP|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1172

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1173

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1174

|Parameter 4| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

1175

|Parameter 5| |●|●|●|●| | | | |●| | | | | | | | | | | | | | |●|●

**Features**

Compare the time of the reference time (hour, minute, second) [(s1), (s2), (s3)] with the time data (hour, minute, second) [(s4), (s4)+1, (s4) +2] Compare the size and turn on/off the 3 points from (d) according to the result of the same size.

1180

1181

[[image:07-5 Basic instructions_html_5df7ad3057fada12.png]]

✎**Note**

The device specified in (s4) and (d) occupies 3 points. Be careful not to overlap with the device used for machine control.

1186

1187

When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.

**Error code**

|**Error code**|**Content**

1192

|4085H|When reading the specified device range exceeds the corresponding device range

1193

|4086H|When writing the specified device range exceeds the corresponding device range

1194

|4084H|(((

1195

When the value specified in (s) and (s4) is not in the range of 0 to 23

1196

1197

{{id name="OLE_LINK355"/}}When the value specified in (s2),(s3) (s4)+1 and (s4)+2 is not in the range of 0 to 59

)))

**Example**

[[image:07-5 Basic instructions_html_fcc16317cf7c0700.png]]

1203

1204

Set D10 to 1, D11 to 30, D12 to 0

1205

1206

When M0 is turned on, the time that D23 will come is 0:31:27

1207

1208

[[image:07-5 Basic instructions_html_de97dd7a612b2323.png]]

M10 is turned ON

[[image:07-5 Basic instructions_html_56e2d606adc09fd.png]]

1213

1214

{{id name="_Toc29031"/}}{{id name="_Toc22923"/}}**TZCP/Clock data bandwidth comparison**

1215

1216

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **TZCP(P)**

1217

1218

Compare the comparison time of the high and low points specified in (s1) and (s2) with the time data specified in (s3), and turn the bit device specified in (d) ON/OFF according to its size and bandwidth.

1219

1220

-[TZCP (s1) (s2) (s3) (d)]

1221

1222

**Content, range and data type**

1223

1224

1225

|(s1)|Specify the "hour" of the lower limit time (hour, minute, second)|-|Signed BIN 16 bit|(((

1226

ANY16_ARRAY

1227

1228

(number of elements: 3)

1229

)))

1230

|(s2)|Specify the "hour" of the lower limit time (hour, minute, second)|-|Signed BIN 16 bit|(((

1231

ANY16_ARRAY

1232

1233

(number of elements: 3)

1234

)))

1235

|(s3)|Specify "hour" of time data (hour, minute, second)|-|Signed BIN 16 bit|(((

1236

ANY16_ARRAY

1237

1238

(number of elements: 3)

1239

)))

1240

|(d)|The bit device is turned ON/OFF according to the comparison result.|-|Bit|(((

1241

ANY16_ARRAY

1242

1243

(number of elements: 3)

)))

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1254

|(% rowspan="4" %)TZCP|Parameter 1| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

1255

|Parameter 2| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

1256

|Parameter 3| | | | | | | | | | | | | | |●|●|●|●|●| | | | | |●|●

1257

|Parameter 4| |●|●|●|●| | | | |●| | | | | | | | | | | | | | |●|●

**Features**

Compare the comparison time of the high and low points specified in (s1) and (s2) with the time data specified in (s3), and turn the bit device specified in (d) ON/OFF according to its size and bandwidth.

1262

1263

[[image:07-5 Basic instructions_html_844291270080313d.png]]

✎**Note**

• The devices specified in (s1), (s2), (s3), (d) occupy 3 points. Be careful not to overlap with the device used for machine control.

1268

1269

• When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.

1270

1271

• When (s1)> (s2), two of (d), (d)+1, (d)+2 are ON/OFF.

**Error code**

|**Error code**|**Content**

1276

|4085H|When reading the specified device range exceeds the corresponding device range

1277

|4086H|When writing the specified device range exceeds the corresponding device range

1278

|4084H|(((

1279

When the value specified in (s1), (s2) and (s3) is not in the range of 0 to 23

1280

1281

When the value specified in (s1)+1, (s2)+1, (s3)+1, (s1)+2, (s2)+2 and (s3)+2 is not in the range of 0 to 59

)))

**Example**

[[image:07-5 Basic instructions_html_30027a2387c26c2e.png]]

1287

1288

Set D0 time to 16:30:00 and D10 time to 4:30:0

1289

1290

[[image:07-5 Basic instructions_html_c64e0faf2af172f8.png]]

1291

1292

[[image:07-5 Basic instructions_html_66e3a2eadeb2ecbb.png]]

1293

1294

After the coil is turned on, the reading time to D20 time is 8:30:00

1295

1296

[[image:07-5 Basic instructions_html_75c44dad07eaf80a.png]]

M0/M12 is ON

[[image:07-5 Basic instructions_html_f512f36261705953.png]]

1301

1302

{{id name="_Toc6129"/}}[[image:07-5 Basic instructions_html_a2e3294e01b2f206.gif]] **7.13 Data control instructions**

1303

1304

{{id name="_Toc3339"/}}{{id name="_Toc27829"/}}{{id name="_Toc9204"/}}**BAND/BIN 16-bit data dead zone control**

1305

1306

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **BAND(P)**

1307

1308

The input value (BIN 16-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the upper and lower limits of the dead zone specified in (s1) and (s2).

1309

1310

-[BAND (s1) (s2) (S3) (d)]

1311

1312

**Content, range and data type**

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1332

|(% rowspan="4" %)BAND|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1333

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1334

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

1335

|Parameter 4| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

The input value (BIN 16-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the upper and lower limits of the dead zone specified in (s1) and (s2). The output value is controlled as follows.

1340

1341

|**Condition**|**The value stored in the output value**

1342

|When dead zone low limit (s1)> input value (s3)|Input value (s3)-Dead zone low limit (s1)

1343

|When dead zone high limit (s1) <input value (s3)|Input value (s3)- Dead zone high limit (s2)

1344

|When dead zone low limit (s1) ≤ input value (s3) ≤ dead zone low limit (s2)|0

(((

•When the output value stored in (d) is a signed BIN 16-bit value, and the operation result exceeds the range of -32768 to 32767, the situation is shown in the following example.

1349

1350

For example, when (s1) is 10 and (s3) is -32768,

1351

1352

the output value = -32768-10=8000H-000AH=7FFFH=32758.

1353

1354

[[image:07-5 Basic instructions_html_6850e21a76b813c0.png]]

)))

**Error code**

|**Error code**|**Content**

1360

|4085H|When the specified device range for reading exceeds the range of the corresponding device.

1361

|4086H|When the specified device range for writing exceeds the range of the corresponding device.

1362

|4084H|When the low limit specified in (s1) is greater than the high limit specified in (s2).

1363

1364

**Example                     **

1365

1366

[[image:07-5 Basic instructions_html_c0e65cfeed403ecf.png]]

1367

1368

When X000 is ON, when D0<(-1,000), the value of ( D0)-(-1,000) is stored in (D1).

1369

1370

• When -1,000≦ D0≦1,000, 0 is stored in D1.

1371

1372

• When D0<1,000, the value of (D0)-1,000 is stored in D1.

1373

1374

{{id name="_Toc1180"/}}{{id name="_Toc21657"/}}{{id name="_Toc27323"/}}[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DBAND/BIN 32-bit data dead zone control**

**DBAND(P)**

The input value (BIN 32-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the upper and lower limits of the dead zone specified in (s1) and (s2).

1379

1380

-[DBAND (s1) (s2) (S3) (d)]

1381

1382

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1398

|(% rowspan="4" %)DBAND|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

1399

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

1400

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●| | | |●|●

1401

|Parameter 4| | | | | | | | | | | |●|●|●|●|●|●|●|●|●|●| | | |●|●

**Features**

The input value (BIN 32-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the upper and lower limits of the dead zone specified in (s1) and (s2). The output value is controlled as follows.

1406

1407

|**Condition**|**The value stored in the output value**

1408

|When dead zone low limit ((s1), (s1)+1)> input value ((s3), (s3)+1)|{{id name="OLE_LINK42"/}}Input value ((s3), (s3)+1)-dead zone low limit ((s1), (s1)+1)

1409

|When dead zone high limit ((s1), (s1)+1) <input value ((s3), (s3)+1)|{{id name="OLE_LINK357"/}}Input value ((s3), (s3)+1)-dead zone high limit ((s2), (s2)+1)

1410

|When dead zone low limit ((s1), (s1)+1) ≤ input value ((s3), (s3)+1) ≤ dead zone high limit ((s2), (s2)+1)|0

(((

• When the output value stored in (d) is a signed BIN 32-bit value, and the operation result exceeds the range of -2,147,483,648 to 2,147,483,647, the situation is as the following example. For example,**  **When (s1) and (s1)+1 are 1000, (s3) and (s3)+1 are -2,147,483,648, then the output value=

1415

1416

-2,147,483,648-1000=80000000H-000003E8H=7FFFFC18H=2,147,482,648.

1417

1418

[[image:07-5 Basic instructions_html_e0144674dad3e8fd.png]]

)))

**Error code**

|**Error code**|**Content**

1427

|4085H|When the specified device range for reading exceeds the range of the corresponding device.

1428

|4086H|When the specified device range for writing exceeds the range of the corresponding device.

1429

|4084H|When the low limit specified in (s1) is greater than the high limit specified in (s2).

**Example**

[[image:07-5 Basic instructions_html_88f3fe0fb4841bab.png]]

1434

1435

• When (D1, D0)<(-10,000), the value of (D1, D0)-(-10,000) is stored in (D11, D10).

1436

1437

• When -10,000≦(D1, D0)≦10,000, 0 is stored in (D11, D10).

1438

1439

• When 10,000< (D1, D0), the value of (D1, D0)-10,000 is stored in D1.

1440

1441

{{id name="_Toc21668"/}}{{id name="_Toc25056"/}}{{id name="_Toc17582"/}}{{id name="OLE_LINK165"/}}**BINDA/BIN 16-bit data → Decimal ASCII conversion**

1442

1443

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **BINDA(P)**

1444

1445

Convert the BIN 16-bit data specified in (s) and the value of each digit in decimal numbers into ASCII codes and store them after the device number specified in (d).

-[BINDA(s)(d)]

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1463

|(% rowspan="2" %)BINDA|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1464

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

**Features**

Convert the BIN 16-bit data specified in (s) and the value of each digit in decimal numbers into ASCII codes and store them after the device number specified in (d).

(((

←Only store 0 when SM191 is OFF

1474

1475

[[image:07-5 Basic instructions_html_57bda5f08026449d.png]]

1476

)))

1477

1478

For example, when -12,345 is specified in (s) (in the case of specifying signed)

1479

1480

[[image:07-5 Basic instructions_html_f346102467b9bef9.png]]

1481

1482

The calculation result stored in (d) will be as below.

1483

1484

• In "Sign", 20H is stored when the BIN data is positive, and 2DH is stored when it is negative.

1485

1486

• In the 0 to the left of the effective digit, 20H is stored. (Suppress 0.) For example, in the case of "00325", "00" becomes 20H, and "325" becomes the effective digit.

1487

1488

• When storing data to the device specified in (d)+3, when SM191 (output character number switching signal) is OFF, 0 is stored, and it does not change when it is ON.

1489

1490

✎**Note: **The number of occupied points of (d) is 3 when SM191 is ON, and it is 4 when SM191 is OFF.

**Error code**

|**Error code**|**Content**

1495

|4085H|The read address of (s) exceeds the device range.

1496

|4086H|The write address of (d) exceeds the device range.

**Example**

(((

When X000 is ON, convert the value of 16-bit data (BIN) D1000 into decimal ASCII code, and then use PR instruction to output the

1504

1505

converted ASCII code character by character to the program of Y040 to Y057.

1506

1507

[[image:07-5 Basic instructions_html_c598806a42484ed.png]]

1508

)))

1509

1510

{{id name="_Toc12255"/}}{{id name="_Toc8216"/}}{{id name="_Toc470"/}}**DBINDA/BIN 32-bit data → Decimal ASCII conversion**

1511

1512

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DBINDA(P)**

1513

1514

Convert the BIN 32-bit data specified in (s) and the value of each bit in decimal numbers into ASCII codes and store them after the device number specified in (d).

-[DBINDA(s)(d)]

**Content, range and data type**

|(d)|{{id name="OLE_LINK2"/}}The start number of the device storing the conversion result|-|String|ANYSTRING_SINGLE

**Device used**

|(% rowspan="2" %)**Instruction**|(% rowspan="2" %)**Parameter**|(% colspan="24" %)**Devices**|(((

**Offset**

**modification**

)))|(((

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1536

|(% rowspan="2" %)DBINDA|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

1537

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

**Features**

Convert the BIN 32-bit data specified in (s) and the value of each bit when expressed in decimal numbers into ASCII codes, and store them after the device number specified in (d).

1542

1543

For example, when -12345678 is specified in (s). (in the case of specifying signed)

1544

1545

[[image:07-5 Basic instructions_html_4d939462838cf09b.gif]] The calculation result stored in (d) will be as below.

1546

1547

• In "Sign", 20H is stored when the BIN data is positive, and 2DH is stored when it is negative.

1548

1549

• 20H is stored at 0 to the left of the effective number of digits. (Suppress 0.) For example, in the case of "0012034560", "00" becomes 20H, and "12034560" becomes effective digits.

1550

1551

• For the data stored in the upper 8 bits of the device specified in (d)+5, 0 will be stored when SM191 (output character switching signal) is OFF, and 20H will be stored when it is ON.

1552

1553

✎**Note: **(d) Occupies 6 points.

**Error code**

|**Error code**|**Content**

1558

|4085H|(s) read address exceeds the device range

1559

|4086H|(d) write address exceeds the device range

**Example**

[[image:07-5 Basic instructions_html_ec8ac32d748a991c.png]]

1564

1565

When X000 is ON, convert the value of 32-bit data (BIN) D1000 into decimal ASCII code, and then use PR (FNC 77) instruction to output the converted ASCII code character by character to the program in Y040 to Y051 in time and time division.

1566

1567

{{id name="_Toc19693"/}}{{id name="_Toc18078"/}}{{id name="_Toc5726"/}}**DABIN/Decimal ASCII → BIN conversion**

1568

1569

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DABIN(P)**

1570

1571

Digital ASCII code (30H to 39H) is a instruction to convert real data into BIN data.

-[DABIN (s) (d)]

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1589

|(% rowspan="2" %)DABIN|Parameter 1| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

1590

|Parameter 2| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

The decimal ASCII data stored after the device number specified in (s) is converted into BIN 16-bit data and stored in the device specified in (d).

1595

1596

[[image:07-5 Basic instructions_html_22c5cb32a0a32214.png]]

|**ASCII code**|(((

{{id name="OLE_LINK36"/}}Units of

ASCII code

)))|(((

Tens of

ASCII code

)))|(((

Hundreds of

ASCII code

)))|(((

Thousands of

ASCII code

)))|(((

Ten thousands

of ASCII code

)))

For example, When -25,108 is specified in (s)

1622

1623

[[image:07-5 Basic instructions_html_10fb2792e37dbf23.png]]

1624

1625

• The ASCII data specified in (s) to (s)+2 is within the range of -32,768 to +32,767.

1626

1627

• In “Sign”, set 20H when the converted data is positive, and set 2DH when it is negative. (When other than 20H or 2DH is set, it will be treated as positive data. (DABIN(P))

1628

1629

• The range of the ASCII code set in each digit is 30H to 39H.

1630

1631

• When the ASCII code set in each bit is 20H or 00H, it will be treated as 30H.

**Error code**

|**Error code**|**Content**

1636

|4084H|(((

1637

When the Sign data exceeds the range of 30H to 39H, 20H, 00H, 2DH;

1638

1639

When the ASCII code of each bit specified in (s) to (s)+2 exceeds the range of 30H to 39H, 20H, 00H;

1640

1641

When the ASCII data specified in (s) to (s)+2 is other than -32,768 to +32,767.

1642

)))

1643

|4085H|The read address of (s) exceeds the device range.

1644

|4086H|The write address of (d) exceeds the device range.

(((

When X000 is ON, the Signs set in D20 to D22 and the ASCII code data of 5-digit decimal numbers are converted into BIN values, and then stored in the program of D0.

**Example**

)))

[[image:07-5 Basic instructions_html_bec2bea131b58c03.png]]

1654

1655

{{id name="_Toc3351"/}}{{id name="_Toc26383"/}}{{id name="_Toc26233"/}}**DDABIN/Decimal ASCII → BIN32-bit data conversion**

1656

1657

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DDABIN(P)**

1658

1659

The decimal ASCII data stored after the device number specified in (s) is converted into BIN 32-bit data and stored in the device number specified in (d).

-[DDABIN (s) (d) ]

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1677

|(% rowspan="2" %)DDABIN|Parameter 1| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

1678

|Parameter 2| | | | | | | | | | | |●|●|●|●|●|●|●|●|●|●| | | |●|●

**Features**

The decimal ASCII data stored after the device number specified in (s) is converted into BIN 32-bit data and stored in the device specified in (d).

1683

1684

[[image:07-5 Basic instructions_html_c444110b273f33b7.gif]]

1685

1686

|**ASCII S**|**ASCII code**|**ASCII S**|**ASCII code**

1687

|ASCII 10^^0^^|Units of ASCII code|ASCII 10^^5^^|{{id name="OLE_LINK38"/}}Hundred thousands of ASCII code

1688

|ASCII 10^^1^^|Tens of ASCII code|ASCII 10^^6^^|Millions of ASCII code

1689

|ASCII 10^^2^^|Hundreds of ASCII code|ASCII 10^^7^^|Ten millions of ASCII code

1690

|ASCII 10^^3^^|{{id name="OLE_LINK37"/}}Thousands of ASCII code|ASCII 10^^8^^|Hundred millions of ASCII code

1691

|ASCII 10^^4^^|Tens thousands of ASCII code|ASCII 10^^9^^|billions of ASCII code

1692

1693

When -1234543210 is specified in (s) (When signed is specified)

1694

1695

[[image:07-5 Basic instructions_html_1b4c7e1c663a4399.png]]

1696

1697

• The ASCII data specified in (s) to (s)+5 is within the range of -2,147,483,648 to +2,147,483,647. In addition, the data stored in the high byte of (s)+5 will be ignored.

1698

1699

• In the Sign data, set 20H when the converted data is positive, and set 2DH when it is negative. (When other than 20H or 2DH is set, it will be treated as positive data. (DABIN(P))

1700

1701

• The range of ASCII code set in each digit is 30H to 39H.

1702

1703

• When the ASCII code set in each bit is 20H or 00H, it will be treated as 30H.

**Error code**

|**Error code**|**Content**

1708

|4084H|(((

1709

When the Sign data exceeds the range of 30H to 39H, 20H, 00H and 2DH;

1710

1711

{{id name="OLE_LINK39"/}}When the ASCII code of each bit specified in (s) to (s)+5 exceeds the range of 30H to 39H, 20H and 00H;

1712

1713

When the ASCII data specified in (s) to (s)+5 exceeds the range of -2,147,483,648 to +2,147,483,647

1714

)))

1715

|4085H|The read address of (s) exceeds the device range.

1716

|4086H|The write address of (d) exceeds the device range.

**Example**

[[image:07-5 Basic instructions_html_feea438c943ea9dd.png]]

1721

1722

When X000 is ON, the Signs set in to D20 to D25 and the ASCII code data of 10-digit decimal numbers are converted into BIN values and then saved to the program in D0 to D1.

1723

1724

{{id name="_Toc26556"/}}{{id name="_Toc12799"/}}{{id name="_Toc23863"/}}**LIMIT/ BIN 16-bit data high and low limit control**

1725

1726

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **LIMIT(P)**

1727

1728

The input value (BIN 16-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the upper and lower limit value ranges specified in (s1) and (s2).

1729

1730

-[LIMIT (s1) (s2) (s3) (d)]

1731

1732

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1748

|(% rowspan="4" %)LIMIT|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1749

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1750

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

1751

|Parameter 4| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

The input value (BIN 16-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the high and low limit value ranges specified in (s1) and (s2). The output value is controlled as follows.

1756

1757

|**Condition**|**The value stored in the output value**

1758

|Low limit value (s1)>input value (s3)|Low limit value (s1)

1759

|High limit value (s1) <input value (s3)|High limit value (s2)

1760

|Low limit value (s1) ≤ input value (s3) ≤ high limit value (s2)|Input value (s3)

(((

•Only in the case of controlling high limit value, set the minimum value of data range in the low limit value specified in (s1).

1765

1766

• Only in the case of controlling low limit value, set the maximum value of data range in the high limit value specified in (s2).

1767

1768

[[image:07-5 Basic instructions_html_50eb5229b027aa14.png]]

)))

**Error code**

|**Error code**|**Content**

1774

|4085H|The read address exceeds the device range

1775

|4086H|The write address exceeds the device range

1776

|4084H|High limit <low limit

**Example**

[[image:07-5 Basic instructions_html_d67a2e740d4fc738.png]]

When X000 is ON

• When D0 <500, D1 is 500.

1785

1786

• When 500 ≤ D0 ≤ 5,000, D1 is the value of D0.

1787

1788

• When 5,000 <D0, D1 is 5,000.

1789

1790

{{id name="_Toc32553"/}}{{id name="_Toc9981"/}}{{id name="_Toc9158"/}}**DLIMIT/BIN 32-bit data high and low limit control**

1791

1792

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DLIMIT(P)**

1793

1794

The input value (BIN 32-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the range of high and low limit values specified in (s1) and (s2).

1795

1796

-[DLIMIT (s1) (s2) (s3) (d)]

1797

1798

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1814

|(% rowspan="4" %)DLIMIT|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

1815

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

1816

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●| | | |●|●

1817

|Parameter 4| | | | | | | | | | | |●|●|●|●|●|●|●|●|●|●| | | |●|●

**Features**

The input value (BIN 32-bit value) specified in (s3) controls the output value stored in the device specified in (d) according to the range of high and low limit values specified in (s1) and (s2). The output value is controlled as follows.

1822

1823

|**Condition**|**The value stored in the output value**

1824

|Low limit value ((s1), (s1)+1)> input value ((s3), (s3)+1)|Low limit value ((s1), (s1)+1)

1825

|High limit value ((s2), (s2)+1) <input value ((s3), (s3)+1)|High limit value ((s2), (s2)+1)

1826

|Low limit value ((s1), (s1)+1) ≤ input value ((s3), (s3)+1) ≤ high limit value ((s2), (s2)+1)|Input value ((s3), (s3)+1)

1827

1828

{{id name="OLE_LINK43"/}}{{id name="OLE_LINK40"/}}•Only in the case of controlling high limit value, set the minimum value of data range in the low limit value specified in (s1).

1829

1830

• Only in the case of controlling low limit value, set the maximum value of data range in the high limit value specified in (s2).

**Error code**

|**Error code**|**Content**

1835

|4085H|The read address exceeds the device range

1836

|4086H|The write address exceeds the device range

1837

|4084H|High limit <low limit

**Example**

[[image:07-5 Basic instructions_html_217355b90f4b4e16.png]]

Operation:

• When (D1, D0) <10,000, (D11, D10) is 10,000.

1846

1847

• When 10,000 ≤ (D1, D0) ≤ 1,000,000, (D11, D10) is the value of (D1, D0).

1848

1849

• When 1,000,000 <(D1, D0), (D11, D10) is 1,000,000.

1850

1851

{{id name="_Toc12534"/}}{{id name="_Toc28213"/}}{{id name="_Toc24591"/}}**SCL/BIN 16-bit unit scale (coordinate data of each point)**

1852

1853

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **SCL(P)**

1854

1855

The scaling conversion data (16-bit data unit) specified in (s2) is scaled from the input value specified in (s1), and the calculation result is stored in the device specified in (d).

-[SCL (s1) (s2) (d)]

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1874

|(% rowspan="3" %)SCL|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

1875

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

1876

|Parameter 3| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

For the scale conversion data (16-bit data unit) specified in (s2), scale by the input value specified in (s1), and store the operation result in the device specified in (d). Scale conversion is performed based on the scale conversion data stored after the device specified in (s2).

1881

1882

|(% colspan="2" %)**Setting items (n represents the number of coordinate points specified in (s2))**|**Device allocation**

1883

|(% colspan="2" %)Coordinate points|(s2)

1884

|(% rowspan="2" %)Point 1|X coordinate|(s2)+1

1885

|Y coordinate|(s2)+2

1886

|(% rowspan="2" %)Point 2|X coordinate|(s2)+3

1887

|Y coordinate|(s2)+4

1888

|(% colspan="3" %)........

1889

|(% rowspan="2" %)Point n|X coordinate|(s2)+2n-1

1890

|Y coordinate|(s2)+2n

1891

1892

[[image:07-5 Basic instructions_html_80185ccddb878234.png]]

1893

1894

• If the operation result is not an integer value, round the first digit below the decimal point.

1895

1896

• The X coordinate data of the conversion data for scaling should be set in ascending order.

1897

1898

• (s1) should be set within the range of conversion data for scaling (device value of (s2)).

1899

1900

• If the same X coordinate is specified for multiple points, the Y coordinate value of the second point will be output.

1901

1902

• Set the number of coordinate points of the conversion data for scaling within the range of 1 to 32,767.

1903

1904

• Setting example of conversion table for scaling.

1905

1906

In the case of scaling conversion characteristics as shown in the figure below, set it as the following data sheet.

1907

1908

[[image:07-5 Basic instructions_html_74fd22d845ad450e.png]]

1909

1910

|(% colspan="2" rowspan="2" %)**Set     items**|(% colspan="3" %)**Sett     device and content**|(% rowspan="2" %)**Remarks**

1911

|(% colspan="2" %)**When R0 is specified in (s2)**|**Set     content**

1912

|(% colspan="2" %)Coordinate points|(s2)|R0|K10|

1913

|(% rowspan="2" %)Point 1|X coordinate|(s2)+1|R1|K5|

1914

|Y coordinate|(s2)+2|R2|K20|

1915

|(% rowspan="2" %)Point 2|X coordinate|(s2)+3|R3|K30|

1916

|Y coordinate|(s2)+4|R4|K50|

1917

|(% rowspan="2" %)Point 3|X coordinate|(s2)+5|R5|K100|

1918

|Y coordinate|(s2)+6|R6|K200|

1919

|(% rowspan="2" %)Point 4|X coordinate|(s2)+7|R7|K25|(% rowspan="6" %)(((

1920

If the coordinates are specified by 3 points, the intermediate value could be the output value.

1921

1922

In this example, the output value (median value) is specified by the Y coordinate of point 5.

1923

1924

When the X coordinate is the same at 3 points or more, the value of the 2nd point is also output.

1925

)))

1926

|Y coordinate|(s2)+8|R8|K200

1927

|(% rowspan="2" %)Point 5|X coordinate|(s2)+9|R9|K70

1928

|Y coordinate|(s2)+10|R10|K200

1929

|(% rowspan="2" %)Point 6|X coordinate|(s2)+11|R11|K250

1930

|Y coordinate|(s2)+12|R12|K250

1931

|(% rowspan="2" %)Point 7|X coordinate|(s2)+13|R13|K250|

1932

|Y coordinate|(s2)+14|R14|K90|

1933

|(% rowspan="2" %)Point 8|X coordinate|(s2)+15|R15|K350|(% rowspan="4" %)(((

1934

If the coordinates are specified by two points, the output value is the value of the Y coordinate of the next point.

1935

1936

In this example, the output value is specified by the Y coordinate of point 9.

1937

)))

1938

|Y coordinate|(s2)+16|R16|K90

1939

|(% rowspan="2" %)Point 9|X coordinate|(s2)+17|R17|K350

1940

|Y coordinate|(s2)+18|R18|K30

1941

|(% rowspan="2" %)Point 10|X coordinate|(s2)+19|R19|K400|

1942

|Y coordinate|(s2)+20|R20|K7|

**Error code**

|**Error code**|**Content**

1947

|4085H|When the specified device range for reading exceeds the range of the corresponding device.

1948

|4086H|When the specified device range for writing exceeds the range of the corresponding device.

1949

|4084H|(((

1950

When the Xn data of data table is not sorted in ascending order. However, the instruction will be executed until the position where the error occurs;

1951

1952

When the input value specified in (s1) exceeds the range of the set scale conversion data;

1953

1954

When the number of start coordinate points of device (s2) is less than 0.

)))

**Example**

[[image:07-5 Basic instructions_html_5519d7b41f15b6d6.png]]

1960

1961

[[image:07-5 Basic instructions_html_ace075fb7675de8e.gif]] When -100 ≤ D0(X) < 0, D100(Y)=

1962

1963

[[image:07-5 Basic instructions_html_9acd6306c6d91847.gif]] when D0(X)=0, D100(Y)=0;

1964

1965

when 0< D0(X) ≤ 100, D100(Y)=

1966

1967

[[image:07-5 Basic instructions_html_e35e13160c08a133.png]]

{{id name="_Toc4862"/}}{{id name="_Toc11340"/}}{{id name="_Toc25383"/}}**DSCL/32-bit unit scale (coordinate data of each point)**

1972

1973

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DSCL(P)**

1974

1975

The conversion data (32-bit data unit) for scaling specified in (s2) is scaled by the input value specified in (s1), and the operation result is stored in the device specified in (d).

1976

1977

-[DSCL (s1) (s2) (d)]

1978

1979

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

1994

|(% rowspan="3" %)DSCL|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

1995

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

1996

|Parameter 3| | | | | | | | | | | |●|●|●|●|●|●|●|●|●|●| | | |●|●

**Features**

{{id name="OLE_LINK41"/}}The conversion data (32-bit data unit) for scaling specified in (s2) is scaled by the input value specified in (s1), and the operation result is stored in the device number specified in (d). The scale conversion is performed based on the scale conversion data stored after the device specified in (s2).

2001

2002

|(% colspan="2" %)**Set items (n represents the number of coordinate points specified in (s2))**|**Device allocation**

2003

|(% colspan="2" %)Coordinate points|(s2)+1, (s2)

2004

|(% rowspan="2" %)Point 1|X coordinate|(s2)+3, (s2)+2

2005

|Y coordinate|(s2)+5, (s2)+4

2006

|(% rowspan="2" %)Point 2|X coordinate|(s2)+7, (s2)+6

2007

|Y coordinate|(s2)+9, (s2)+8

2008

|(% colspan="3" %)........

2009

|(% rowspan="2" %)Point n|X coordinate|(s2)+4n-1, (s2)+4n-2

2010

|Y coordinate|(s2)+4n+1, (s2)+4n

2011

2012

[[image:07-5 Basic instructions_html_6633ca18cee1218c.png]]

2013

2014

• If the calculation result is not an integer value, round the first digit below the decimal point.

2015

2016

• The X coordinate data of the conversion data for scaling should be set in ascending order.

2017

2018

• For (s1), set within the range of the conversion data for scaling ((s2), (s2) + 1 device value).

2019

2020

• If the same X coordinate is specified for multiple points, the Y coordinate value of the second point will be output.

2021

2022

• Set the number of coordinate points of conversion data for scaling within the range of 1 to 2,147,483,647.

2023

2024

• Setting example of conversion table for scaling.

2025

2026

In the case of scaling conversion characteristics as shown in the figure below, set it as the following data sheet.

2027

2028

[[image:07-5 Basic instructions_html_74fd22d845ad450e.png]]

2029

2030

|(% colspan="2" rowspan="2" %)**Set items**|(% colspan="3" %)**Set     device and content**|(% rowspan="2" %)**Remarks**

2031

|(% colspan="2" %)**When R0 is specified in (s2)**|**Set     content**

2032

|(% colspan="2" %)Coordinate points|(s2)+1, (s2)|R1, R0|K10|

2033

|(% rowspan="2" %)Point 1|X coordinate|(s2)+3, (s2)+2|R3, R2|K5|

2034

|Y coordinate|(s2)+5, (s2)+4|R5, R4|K7|

2035

|(% rowspan="2" %)Point 2|X coordinate|(s2)+7, (s2)+6|R7, R6|K20|

2036

|Y coordinate|(s2)+9, (s2)+8|R9, R8|K30|

2037

|(% rowspan="2" %)Point 3|X coordinate|(s2)+11, (s2)+10|R10, R11|K50|

2038

|Y coordinate|(s2)+13, (s2)+12|R13, R12|K100|

2039

|(% rowspan="2" %)Point 4|X coordinate|(s2)+15, (s2)+14|R15, R14|K200|(% rowspan="6" %)(((

2040

if the coordinates are specified by 3 points, the intermediate value could be the output value.

2041

2042

In this example, the output value (median value) is specified by the Y coordinate of point 5.

2043

2044

When the X coordinate is the same at 3 points or more, the value of the 2nd point is also output.

2045

)))

2046

|Y coordinate|(s2)+17, (s2)+16|R17, R16|K25

2047

|(% rowspan="2" %)Point 5|X coordinate|(s2)+19, (s2)+18|R19, R18|K200

2048

|Y coordinate|(s2)+21, (s2)+20|R21, R20|K70

2049

|(% rowspan="2" %)Point 6|X coordinate|(s2)+23, (s2)+22|R23, R22|K200

2050

|Y coordinate|(s2)+25, (s2)+24|R25, R24|K250

2051

|(% rowspan="2" %)Point 7|X coordinate|(s2)+27, (s2)+26|R27, R26|K250|

2052

|Y coordinate|(s2)+29, (s2)+28|R29, R28|K90|

2053

|(% rowspan="2" %)Point 8|X coordinate|(s2)+31, (s2)+30|R31, R30|K350|(% rowspan="4" %)(((

2054

If the coordinates are specified by two points, the output value is the value of the Y coordinate of the next point.

2055

2056

In this example, the output value is specified by the Y coordinate of point 9.

2057

)))

2058

|Y coordinate|(s2)+33, (s2)+32|R33, R32|K90

2059

|(% rowspan="2" %)Point 9|X coordinate|(s2)+35, (s2)+34|R35, R34|K350

2060

|Y coordinate|(s2)+37, (s2)+36|R37, R36|K30

2061

|(% rowspan="2" %)Point 10|X coordinate|(s2)+39, (s2)+38|R39, R38|K400|

2062

|Y coordinate|(s2)+41, (s2)+40|R41, R40|K7|

**Error code**

|**Error code**|**Content**

2067

|4085H|When the specified device range for reading exceeds the range of the corresponding device.

2068

|4086H|When the specified device range for writing exceeds the range of the corresponding device.

2069

|4084H|(((

2070

When the Xn data of data table is not sorted in ascending order. However, the instruction will be executed until the position where the error occurs;

2071

2072

When the input value specified in (s1) exceeds the range of the set scale conversion data;

2073

2074

When the number of start coordinate points of device (s2) is less than 0.

)))

**Example**

[[image:07-5 Basic instructions_html_ba95b2d50d8d1d3e.png]]

2080

2081

[[image:07-5 Basic instructions_html_1de79c7d87d51f78.gif]] When -100 ≤ D0(X) < 0, D100(Y)=

2082

2083

[[image:07-5 Basic instructions_html_9acd6306c6d91847.gif]] When D0(X)=0, D100(Y)=0;

2084

2085

When 0 < D0(X) ≤ 100, D100(Y)=

2086

2087

[[image:07-5 Basic instructions_html_a5b19d1af74a9620.png]]

2088

2089

{{id name="_Toc3776"/}}{{id name="_Toc11170"/}}{{id name="_Toc2957"/}}**SCL2/BIN 16-bit unit scale (X/Y coordinate data)**

2090

2091

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **SCL2(P)**

2092

2093

The conversion data (16-bit data unit) for scaling specified in (s2) is scaled by the input value specified in (s1), and the operation result is stored in the device specified in (d).

2094

2095

-[SCL2 (s1) (s2) (d)]

2096

2097

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

2112

|(% rowspan="3" %)SCL2|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

2113

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

2114

|Parameter 3| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

The conversion data (16-bit data unit) for scaling specified in (s2) is scaled by the input value specified in (s1), and the operation result is stored in the device number specified in (d). The scale conversion is performed based on the scale conversion data stored after the device specified in (s2).

2119

2120

|(% colspan="2" %)**Set items (n represents the number of coordinate points specified in (s2))**|**Device allocation**

2121

|(% colspan="2" %)Coordinate points|(s2)

2122

|(% rowspan="4" %)X coordinate|Point 1|(s2)+1

|Point 2|(s2)+2

|.....|......

|Point n|(s2)+n

|(% rowspan="4" %)Y coordinate|Point 1|(s2)+n+1

|Point 2|(s2)+n+2

|.....|.....

|Point n|(s2)+2n

[[image:07-5 Basic instructions_html_80185ccddb878234.png]]

2132

2133

• If the operation result is not an integer value, round the first digit below the decimal point.

2134

2135

• The X coordinate data of the conversion data for scaling should be set in ascending order.

2136

2137

• For (s1), set within the range of the conversion data for scaling ((s2), (s2) + 1 device value).

2138

2139

• If the same X coordinate is specified for multiple points, the Y coordinate value of the second point will be output.

2140

2141

• Set the number of coordinate points of conversion data for scaling within the range of 1 to 32,767.

2142

2143

• Setting example of conversion table for scaling.

2144

2145

In the case of scaling conversion characteristics as shown in the figure below, set it as the following data sheet.

2146

2147

[[image:07-5 Basic instructions_html_74fd22d845ad450e.png]]

2148

2149

|(% colspan="2" rowspan="2" %)**Set items**|(% colspan="3" %)**Set device and content**|(% rowspan="2" %)**Remarks**

2150

|(% colspan="2" %)**When R0 is specified in (s2)**|**Set content**

2151

|(% colspan="2" %)Coordinate points|(s2)|R0|K10|

2152

|(% rowspan="10" %)X coordinate|Point 1|(s2)+1|R1|K5|

2153

|Point 2|(s2)+2|R2|K20|

2154

|Point 3|(s2)+3|R3|K50|

2155

|Point 4|(s2)+4|R4|K200|(% rowspan="3" %)Refer to** ✎1**

2156

|Point 5|(s2)+5|R5|K200

2157

|Point 6|(s2)+6|R6|K200

2158

|Point 7|(s2)+7|R7|K250|

2159

|Point 8|(s2)+8|R8|K350|(% rowspan="2" %)Refer to** ✎2**

2160

|Point 9|(s2)+9|R9|K350

2161

|Point 10|(s2)+10|R10|K400|

2162

|(% rowspan="10" %)Y coordinate|Point 1|(s2)+11|R11|K7|

2163

|Point 2|(s2)+12|R12|K30|

2164

|Point 3|(s2)+13|R13|K100|

2165

|Point 4|(s2)+14|R14|K25|(% rowspan="3" %)Refer to**✎1**

2166

|Point 5|(s2)+15|R15|K70

2167

|Point 6|(s2)+16|R16|K250

2168

|Point 7|(s2)+17|R17|K90|

2169

|Point 8|(s2)+18|R18|K90|(% rowspan="2" %)Refer to** ✎2**

2170

|Point 9|(s2)+19|R19|K30

2171

|Point 10|(s2)+20|R20|K7|

2172

2173

✎**1** Like points 4, 5, and 6, if the coordinates are specified by 3 points, the intermediate value could be the output value.

2174

2175

In this example, the output value (median value) is specified by the Y coordinate of point 5.

2176

2177

When the X coordinate is the same at 3 or more points, the value of the second point is also output.

2178

2179

✎**2** Like points 8 and 9, if the coordinates are specified by 2 points, the output value is the value of the Y coordinate of next point.

2180

2181

In this example, the output value is specified by the Y coordinate of point 9.

**Error code**

|**Error code**|**Content**

2186

|4085H|When the specified device range for reading exceeds the range of the corresponding device.

2187

|4086H|When the specified device range for writing exceeds the range of the corresponding device.

2188

|4084H|(((

2189

When the Xn data of data table is not sorted in ascending order. However, the instruction will be executed until the position where the error occurs;

2190

2191

When the input value specified in (s1) exceeds the range of the set scale conversion data;

2192

2193

When the number of start coordinate points of device (s2) is less than 0.

)))

**Example**

[[image:07-5 Basic instructions_html_ace075fb7675de8e.gif]] [[image:07-5 Basic instructions_html_de529c9a16a62ef0.png]]

2199

2200

When -100 ≤D0 (X) < 0, D100(Y)=

2201

2202

[[image:07-5 Basic instructions_html_9acd6306c6d91847.gif]] when D0(X)=0, D100(Y)=0;

2203

2204

when 0 < D0(X) ≤ 100, D100(Y)=

2205

2206

[[image:07-5 Basic instructions_html_a5b19d1af74a9620.png]]

2207

2208

{{id name="_Toc5608"/}}{{id name="_Toc1756"/}}{{id name="_Toc21402"/}}**DSCL2/BIN 32-bit unit scale (X/Y coordinate data)**

2209

2210

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **DSCL2(P)**

2211

2212

The conversion data (32-bit data unit) for scaling specified in (s2) is scaled by the input value specified in (s1), and the operation result is stored in the device specified in (d).

2213

2214

-[DSCL2 (s1) (s2) (d)]

2215

2216

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

2231

|(% rowspan="3" %)DSCL2|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

2232

|Parameter 2| | | | | | | | | | | | | | | | |●|●|●| | | | | |●|●

2233

|Parameter 3| | | | | | | | | | | |●|●|●|●|●|●|●|●|●|●| | | |●|●

**Features**

The conversion data (32-bit data unit) for scaling specified in (s2) is scaled by the input value specified in (s1), and the operation result is stored in the device number specified in (d). The scale conversion is performed based on the scale conversion data stored after the device specified in (s2).

2238

2239

|(% colspan="2" %)**Set items (n represents the number of coordinate points specified in (s2))**|**Device allocation**

2240

|(% colspan="2" %)Coordinate points|(s2)+1, (s2)

2241

|(% rowspan="4" %)X coordinate|Point 1|(s2)+3, (s2)+2

2242

|Point 2|(s2)+5, (s2)+4

2243

|.....|......

2244

|Point n|(s2)+2n+1, (s2)+2n

2245

|(% rowspan="4" %)Y coordinate|Point 1|(s2)+2n+3, (s2)+2n+2

2246

|Point 2|(s2)+2n+5, (s2)+2n+4

2247

|.....|.....

2248

|Point n|(s2)+4n+1, (s2)+4n

2249

2250

[[image:07-5 Basic instructions_html_6633ca18cee1218c.png]]

2251

2252

• If the operation result is not an integer value, round the first digit below the decimal point.

2253

2254

• The X coordinate data of the conversion data for scaling should be set in ascending order.

2255

2256

• For (s1), set within the range of the conversion data for scaling ((s2), (s2) + 1 device value).

2257

2258

• If the same X coordinate is specified for multiple points, the Y coordinate value of the second point will be output.

2259

2260

• Set the number of coordinate points of conversion data for scaling within the range of 1 to 2,147,483,647.

2261

2262

• Setting example of conversion table for scaling.

2263

2264

In the case of scaling conversion characteristics as shown in the figure below, set it as the following data sheet.

2265

2266

[[image:07-5 Basic instructions_html_74fd22d845ad450e.png]]

2267

2268

|(% colspan="2" rowspan="2" %)**Set     items**|(% colspan="3" %)**Set device and content**|(% rowspan="2" %)**Remarks**

2269

|(% colspan="2" %)**When R0 is specified in (s2)**|**Set content**

2270

|(% colspan="2" %)Coordinate points|(s2)+1, (s2)|R1, R0|K10|

2271

|(% rowspan="10" %)X|Point 1|(s2)+3, (s2)+2|R3, R2|K5|

2272

|Point 2|(s2)+5, (s2)+4|R5, R4|K20|

2273

|Point 3|(s2)+7, (s2)+6|R7, R6|K50|

2274

|Point 4|(s2)+9, (s2)+8|R9, R8|K200|(% rowspan="3" %)Refer to** ✎1**

2275

|Point 5|(s2)+11, (s2)+10|R10, R11|K200

2276

|Point 6|(s2)+13, (s2)+12|R13, R12|K200

2277

|Point 7|(s2)+15, (s2)+14|R15, R14|K250|

2278

|Point 8|(s2)+17, (s2)+16|R17, R16|K350|(% rowspan="2" %)Refer to** ✎2**

2279

|Point 9|(s2)+19, (s2)+18|R19, R18|K350

2280

|Point 10|(s2)+21, (s2)+20|R21, R20|K400|

2281

|(% rowspan="10" %)Y coordinate|Point 1|(s2)+23, (s2)+22|R23, R22|K7|

2282

|Point 2|(s2)+25, (s2)+24|R25, R24|K30|

2283

|Point 3|(s2)+27, (s2)+26|R27, R26|K100|

2284

|Point 4|(s2)+29, (s2)+28|R29, R28|K25|(% rowspan="3" %)Refer to** ✎1**

2285

|Point 5|(s2)+31, (s2)+30|R31, R30|K70

2286

|Point 6|(s2)+33, (s2)+32|R33, R32|K250

2287

|Point 7|(s2)+35, (s2)+34|R35, R34|K90|

2288

|Point 8|(s2)+37, (s2)+36|R37, R36|K90|(% rowspan="2" %)Refer to** ✎2**

2289

|Point 9|(s2)+39, (s2)+38|R39, R38|K30

2290

|Point 10|(s2)+41, (s2)+40|R41, R40|K7|

2291

2292

✎**1** Like points 4, 5, and 6, if the coordinates are specified by 3 points, the intermediate value could be the output value.

2293

2294

In this example, the output value (median value) is specified by the Y coordinate of point 5.

2295

2296

When the X coordinate is the same at 3 or more points, the value of the second point is also output.

2297

2298

✎**2** Like points 8 and 9, if the coordinates are specified by 2 points, the output value is the value of the Y coordinate of the next point.

2299

2300

In this example, the output value is specified by the Y coordinate of point 9.

**Error code**

|**Error code**|**Content**

2305

|4085H|When the specified device range for reading exceeds the range of the corresponding device.

2306

|4086H|When the specified device range for writing exceeds the range of the corresponding device.

2307

|4084H|(((

2308

When the Xn data of data table is not sorted in ascending order. However, the instruction will be executed until the position where the error occurs;

2309

2310

When the input value specified in (s1) exceeds the range of the set scale conversion data;

2311

2312

When the number of start coordinate points of device (s2) is less than 0.

)))

**Example**

[[image:07-5 Basic instructions_html_91dbc16faa9d2ec3.png]]

2318

2319

When -100 ≤D0(X) < 0, D100(Y)=[[image:/xwiki/bin/download/PLC%20Editor2/1%20User%20manual/2.1%20LX5V%20user%20manual/07-5%20Basic%20instruction/WebHome/07-5%20Basic%20instructions_html_2c96d630f666e72c.gif?rev=1.1||alt="07-5 Basic instructions_html_2c96d630f666e72c.gif"]],,[[image:07-5 Basic instructions_html_2c96d630f666e72c.gif]] ,,;

2320

2321

when D0(X)=0, D100(Y)=0;

2322

2323

when 0< D0(X) ≤ 100, D100(Y)=[[image:/xwiki/bin/download/PLC%20Editor2/1%20User%20manual/2.1%20LX5V%20user%20manual/07-5%20Basic%20instruction/WebHome/07-5%20Basic%20instructions_html_47ebf5cc7733fccc.gif?rev=1.1||alt="07-5 Basic instructions_html_47ebf5cc7733fccc.gif"]],,[[image:07-5 Basic instructions_html_47ebf5cc7733fccc.gif]] ,,.

2324

2325

[[image:07-5 Basic instructions_html_a5b19d1af74a9620.png]]

2326

2327

{{id name="_Toc32057"/}}{{id name="_Toc9941"/}}{{id name="_Toc6492"/}}**ZONE/BIN 16-bit data zone control**

2328

2329

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] **ZONE(P)**

2330

2331

After adding the offset value specified in (s1) or (s2) to the input value specified in (s3), it is stored in the device number specified in (d).

2332

2333

-[ZONE (s1) (s2) (s3) (d)]

2334

2335

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

2351

|(% rowspan="4" %)ZONE|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

2352

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | |●|●| |●|●

2353

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●| | | | | |●|●

2354

|Parameter 4| | | | | | | | | | | |●|●|●|●|●|●|●|●| | | | | |●|●

**Features**

After adding the offset value specified in (s1) or (s2) to the input value (BIN 16-bit value) specified in (s3), it is stored in the device number specified in (d). The offset value is controlled as follows.

2359

2360

|**Condition**|**The value stored in the output value**

2361

|When input value (s3)<0|Input value (s3) + negative offset value (s1)

2362

|When input value (s3)=0|0

2363

|When input value (s3)>0|Input value (s3) + positive offset value (s2)

(((

• When the output value stored in (d) is a signed BIN 16-bit value, and the operation result exceeds the range of -32,768 to 32,767, the situation is shown in the following example.

2368

2369

For example, when (s1) is -100 and (s3) is -32,768,

2370

2371

the output value = -32768+(-100)=8000H-FF9CH=7F9CH=32668.

2372

2373

[[image:07-5 Basic instructions_html_a2adbf9ccf8f839.png]]

)))

**Error code**

|**Error code**|**Content**

2382

|4085H|When the specified device range for reading exceeds the range of the corresponding device

2383

|4086H|When the specified device range for writing exceeds the range of the corresponding device

**Example**

[[image:07-5 Basic instructions_html_5da523c7765bf5be.png]]

When X000 is ON

• When D0<0, the value of (D0)+(-1,000) is stored in D1.

2392

2393

• When D0=0, 0 is stored in D1.

2394

2395

• When 0<D0, the value of (D0)+(1,000) is stored in D1.

2396

2397

{{id name="_Toc28351"/}}{{id name="_Toc11023"/}}{{id name="_Toc30269"/}}**DZONE/BIN 32-bit data zone control**

2398

2399

[[image:07-5 Basic instructions_html_11b3991e89e21efc.gif]] DZONE(P)

2400

2401

After adding the offset value specified in (s1) or (s2) to the input value specified in (s3), it is stored in the device number specified in (d).

2402

2403

-[DZONE (s1) (s2) (s3) (d)]

2404

2405

**Content, range and data type**

**Device used**

**Pulse**

**extension**

)))

|**X**|**Y**|**M**|**S**|**SM**|**T(bit)**|**C(bit)**|**LC(bit)**|**HSC(bit)**|**D.b**|**KnX**|**KnY**|**KnM**|**KnS**|**T**|**C**|**D**|**R**|**SD**|**LC**|**HSC**|**K**|**H**|**E**|**[D]**|**XXP**

2421

|(% rowspan="4" %)DZONE|Parameter 1| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

2422

|Parameter 2| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●|●|●| |●|●

2423

|Parameter 3| | | | | | | | | | |●|●|●|●|●|●|●|●|●|●|●| | | |●|●

2424

|Parameter 4| | | | | | | | | | | |●|●|●|●|●|●|●|●|●|●| | | |●|●

**Features**

After adding the offset value specified in (s1) or (s2) to the input value (BIN 32-bit value) specified in (s3), it is stored in the device number specified in (d). The offset value is controlled as follows.

2429

2430

|**Condition**|**The value stored in the output value**

2431

|When input value ((s3), (s3)+1)<0|Input value ((s3), (s3)+1) + negative offset value (s1), (s1)+1

2432

|When input value ((s3), (s3)+1)=0|0

2433

|When input value ((s3), (s3)+1)>0|Input value ((s3), (s3)+1) + positive offset value (s2), (s2)+1

(((

• When the output value stored in (d) and (d)+1 is a signed BIN 32-bit value, and the operation result exceeds the range of -2,147,483,648 to 2,147,483,647, the situation is shown in the following example.

2438

2439

For example, (s1), (s1)+1 is -1,000, (s3), (s3)+1 is -2,147,483,648, then the output value=-2,147,483,648+(-1000)=80000000H+FFFFFC18H=2,147,482,648.

2440

2441

[[image:07-5 Basic instructions_html_2f3a96a2565c75c7.png]]

)))

**Error code**