Wiki source code of 12 Clock operation

Last modified by Mora Zhou on 2023/11/21 17:27

version	line-number	content
16.1	1	== ==
10.1	2
1.4	3	== TADD/The addition of clock data ==
1.1	4
	5	TADD(P)
	6
	7	Add the time data stored after the device number specified in (s1) and the time data stored after the device number specified in (s2), and store the result of the addition operation after the device number specified in (d) .
	8
	9	-[TADD (s1) (s2) (d)]
	10
	11	Content, range and data type
	12
	13	\|Parameter\|Content\|Range\|Data type\|Data type (label)
1.4	14	\|(s1)\|The device start number that stores the added time data\|-\|Signed BIN 16 bit\|(((
1.1	15	ANY16_ARRAY
	16
	17	(number of elements: 3)
	18	)))
	19	\|(s2)\|The device start number that stores the addition operation time (time) data\|-\|Signed BIN 16 bit\|(((
	20	ANY16_ARRAY
	21
	22	(number of elements: 3)
	23	)))
	24	\|(d)\|The device start number that stores the time (time) data of the addition operation result\|-\|Signed BIN 16 bit\|(((
	25	ANY16_ARRAY
	26
	27	(number of elements: 3)
	28	)))
	29
	30	Device used
	31
1.5	32	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="5" %)Devices\|(((
	33	Offset modification
1.1	34	)))\|(((
1.5	35	Pulse extension
1.1	36	)))
1.5	37	\|T\|C\|D\|R\|SD\|[D]\|XXP
	38	\|(% rowspan="3" %)TADD\|Parameter 1\|●\|●\|●\|●\|●\|●\|●
	39	\|Parameter 2\|●\|●\|●\|●\|●\|●\|●
	40	\|Parameter 3\|●\|●\|●\|●\|●\|●\|●
1.1	41
	42	Features
	43
	44	Add the time data specified in (s1) and the time data specified in (s2), and store the result of the addition in the device number specified in (d) or later.
	45
1.5	46	(% style="text-align:center" %)
	47	[[image:07-5 Basic instructions_html_37222a6e282347f9.png\|\|height="79" width="750"]]
1.1	48
	49	Example
	50
	51	When 6:32:40 and 7:48:10 are added together
	52
1.5	53	(% style="text-align:center" %)
	54	[[image:07-5 Basic instructions_html_90138670198ab422.png\|\|height="94" width="750"]]
1.1	55
	56	When the calculation result time exceeds 24 o'clock, the carry flag turns ON, and the value after 24 hours is subtracted becomes the calculation result. For example, when 14:20:30 and 20:20:20 are added, the result is not 34:40:50, but 10:40:50.
	57
1.5	58	(% style="text-align:center" %)
	59	[[image:07-5 Basic instructions_html_bac419ce2dc0dc2.png\|\|height="91" width="750"]]
1.1	60
	61	When the calculation result is 0 (0 hour, 0 minute, 0 second), the zero flag turns on.
	62
	63	When 23:59:59 and 1 second are added, the result of the calculation is 0:00:00, and the carry flag and zero flag are turned on.
	64
	65	Related device are as follows:
	66
	67	\|Devices\|Name\|Content
	68	\|SM151\|Carry\|It is ON when the result of the TADD(P) instruction exceeds the maximum clock data value of 23:59:59
	69	\|SM153\|Zero\|It is ON when the result of the TADD(P) instruction is 0:00:00
	70
29.1	71	(% class="box infomessage" %)
	72	(((
	73	✎Note: The devices specified in (s1), (s2), (d) occupy 3 points respectively. Be careful not to overlap with the device used for machine control.
1.1	74
	75	When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.
29.1	76	)))
1.1	77
	78	Error code
	79
	80	\|Error code\|Content
1.5	81	\|4085H\|When reading the specified device range exceeds the corresponding device range
1.1	82	\|4086H\|When writing the specified device range exceeds the corresponding device range
	83	\|4084H\|(((
	84	When the values specified in (s1) and (s2) are other than 0 to 23
	85
	86	When the values specified in (s1)+1, (s2)+1, (s1)+2 and (s2)+2 are other than 0 to 59
	87	)))
	88
	89	Example
	90
1.5	91	(% style="text-align:center" %)
	92	[[image:07-5 Basic instructions_html_4f75eedee7172bbb.png\|\|height="35" width="349"]]
1.1	93
	94	Set D0 time to 16:30:00 and D10 time to 4:30:0
	95
1.5	96	(% style="text-align:center" %)
1.1	97	[[image:07-5 Basic instructions_html_c64e0faf2af172f8.png]]
	98
1.5	99	(% style="text-align:center" %)
1.1	100	[[image:07-5 Basic instructions_html_66e3a2eadeb2ecbb.png]]
	101
	102	After the coil is turned on, the D20 time is 21:0:0
	103
1.5	104	(% style="text-align:center" %)
1.1	105	[[image:07-5 Basic instructions_html_a9b235835aa41200.png]]
	106
1.5	107	== TSUB/The subtraction of clock data ==
1.1	108
1.5	109	TSUB(P)
1.1	110
	111	Subtract the time data stored after the device number specified in (s1) and the time data stored after the device number specified in (s2), and store the subtraction result in the device number specified in (d) or later .
	112
	113	-[TSUB (s1) (s2) (d)]
	114
	115	Content, range and data type
	116
	117	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	118	\|(s1)\|The device start number that stores the subtracted time data\|-\|Signed BIN 16 bit\|(((
	119	ANY16_ARRAY
	120
	121	(number of elements: 3)
	122	)))
	123	\|(s2)\|The device start number that stores the subtraction operation time (time) data\|-\|Signed BIN 16 bit\|(((
	124	ANY16_ARRAY
	125
	126	(number of elements: 3)
	127	)))
	128	\|(d)\|The device start number that stores the time (time) data of the subtraction result\|-\|Signed BIN 16 bit\|(((
	129	ANY16_ARRAY
	130
	131	(number of elements: 3)
	132	)))
	133
	134	Device used
	135
1.5	136	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="5" %)Devices\|(((
	137	Offset modification
1.1	138	)))\|(((
1.5	139	Pulse extension
1.1	140	)))
1.5	141	\|T\|C\|D\|R\|SD\|[D]\|XXP
	142	\|(% rowspan="3" %)TSUB\|Parameter 1\|●\|●\|●\|●\|●\|●\|●
	143	\|Parameter 2\|●\|●\|●\|●\|●\|●\|●
	144	\|Parameter 3\|●\|●\|●\|●\|●\|●\|●
1.1	145
	146	Features
	147
	148	Subtract the time data specified in (s1) and the time data specified in (s2), and store the subtraction result in the device number specified in (d) or later.
	149
1.5	150	(% style="text-align:center" %)
1.1	151	[[image:07-5 Basic instructions_html_5a93455e4cd8a27.png]]
	152
	153	Example
	154
	155	When subtracting 10:40:20 and 3:50:10
	156
1.5	157	(% style="text-align:center" %)
1.1	158	[[image:07-5 Basic instructions_html_2473f03fc493780c.png]]
	159
	160	When the calculation result time is a negative number, the borrow flag turns on and the data +24 is the calculation result. For example, in the case of subtracting 4:50:32 and 10:42:12, the result is not -6:8:20, but 18:8:20.
	161
1.5	162	(% style="text-align:center" %)
1.1	163	[[image:07-5 Basic instructions_html_24b998b4c3c4ec73.png]]
	164
	165	When the calculation result is 0 (0 hour, 0 minute, 0 second), the zero flag turns on.
	166
	167	Related device are as follows:
	168
	169	\|Devices\|Name\|Content
	170	\|SM152\|Borrow\|It is ON when the result of the TSUB(P) instruction is less than 0:00:00
	171	\|SM153\|Zero\|It is ON when the result of the TSUB(P) instruction is at the time of 0:00:00:00
	172
1.5	173	✎Note:
1.1	174
	175	• The devices specified in (s1), (s2), and (d) occupy 3 points respectively. Be careful not to overlap with the device used for machine control.
	176
	177	• When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.
	178
	179	Error code
	180
	181	\|Error code\|Content
	182	\|4085H\|When reading the specified device range exceeds the corresponding device range
	183	\|4086H\|When writing the specified device range exceeds the corresponding device range
	184	\|4084H\|(((
	185	When the values specified in (s1) and (s2) are other than 0 to 23
	186
	187	When the values specified in (s1)+1, (s2)+1, (s1)+2 and (s2)+2 are other than 0 to 59
	188	)))
	189
	190	Example
	191
1.5	192	(% style="text-align:center" %)
	193	[[image:07-5 Basic instructions_html_e3a5d4793d3ccd2d.png\|\|height="36" width="372"]]
1.1	194
	195	Set D0 time to 16:30:00 and D10 time to 4:30:0
	196
1.5	197	(% style="text-align:center" %)
1.1	198	[[image:07-5 Basic instructions_html_c64e0faf2af172f8.png]]
	199
1.5	200	(% style="text-align:center" %)
1.1	201	[[image:07-5 Basic instructions_html_66e3a2eadeb2ecbb.png]]
	202
	203	After the coil is turned on, the D20 time is 12:00:00
	204
1.5	205	(% style="text-align:center" %)
1.1	206	[[image:07-5 Basic instructions_html_8f93ea19ba10652b.png]]
	207
8.1	208	== TRD/Clock data reading ==
1.1	209
	210	TRD(P)
	211
	212	Read the clock data of the built-in real-time clock of the CPU module.
	213
	214	-[TRD (d)]
	215
	216	Content, range and data type
	217
	218	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	219	\|(d)\|Read destination and start device number of clock data\|-\|Signed BIN 16 bit\|(((
	220	ANY16_ARRAY
	221
	222	(number of elements: 7)
	223	)))
	224
	225	Device used
	226
1.5	227	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="4" %)Devices\|(((
	228	Offset modification
1.1	229	)))\|(((
1.5	230	Pulse extension
1.1	231	)))
1.5	232	\|T\|C\|D\|R\|[D]\|XXP
	233	\|TRD\|Parameter 1\|●\|●\|●\|●\|●\|●
1.1	234
	235	Features
	236
	237	Read the clock data (SD100 to SD106) of the real-time clock built into the CPU module into (d) to (d)+6 in the following format.
	238
1.2	239	\|Parameter\|Element\|Project\|Clock data\| \|Element\|Project
1.1	240	\|(% rowspan="7" %)Special register\|SD105\|Year (Gregorian)\|2000 to 2099\|→\|(d)\|Year (Gregorian)
	241	\|SD104\|Month\|1 to 12\|→\|(d)+1\|Month
	242	\|SD103\|Day\|1 to 31\|→\|(d)+2\|Day
	243	\|SD102\|Hour\|0 to 23\|→\|(d)+3\|Hour
	244	\|SD101\|Minute\|0 to 59\|→\|(d)+4\|Minute
	245	\|SD100\|Seconds\|0 to 59\|→\|(d)+5\|Seconds
	246	\|SD106\|Week\|0 (Sun) to 6 (Sat)\|→\|(d)+6\|Week
	247
	248	• The related devices are shown below. The clock data of these special registers are updated through END processing.
	249
	250	\|Devices\|Content
	251	\|SD100\|The second data of the clock data is stored in BIN code.
	252	\|SD101\|The sub-data of the clock data is stored in BIN code.
	253	\|SD102\|Time data of clock data is stored in BIN code.
	254	\|SD103\|The daily data of the clock data is stored in BIN code.
	255	\|SD104\|The monthly data of the clock data is stored in BIN code.
	256	\|SD105\|The year data of the clock data is stored in a 4-digit BIN code of the Gregorian calendar.
	257	\|SD106\|The week data of the clock data is stored in BIN code. (0: day, 1: one, ..., 6: six) are stored in BIN code.
	258
1.5	259	✎Note:
1.1	260
	261	• The device specified in (d) occupies 7 points. Be careful not to overlap with the device used for machine control.
	262
	263	Error code
	264
	265	\|Error code\|Content
	266	\|4086H\|When reading the specified device range exceeds the corresponding device range
	267
	268	Example
	269
1.5	270	(% style="text-align:center" %)
	271	[[image:07-5 Basic instructions_html_b81c1991fec5b4b1.png\|\|height="68" width="250"]]
1.1	272
	273	After the M0 coil is turned on, the current date and time are read as 2020-2-19 13:10:38 Wednesday
	274
1.5	275	(% style="text-align:center" %)
	276	[[image:07-5 Basic instructions_html_fe82ecd18ebfd787.png\|\|height="48" width="602"]]
1.1	277
1.5	278	== TWR/Clock data writing ==
1.1	279
1.6	280	TWR(P)
1.1	281
	282	Write the clock data of the built-in real-time clock of the CPU module.
	283
	284	-[TWR (s)]
	285
	286	Content, range and data type
	287
	288	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	289	\|(s)\|Clock data write source, start device number\|-\|Signed BIN 16 bit\|ANY16_ARRAY (number of elements: 7)
	290
	291	Device used
	292
1.6	293	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="4" %)Devices\|(((
	294	Offset modification
1.1	295	)))\|(((
1.6	296	Pulse extension
1.1	297	)))
1.6	298	\|T\|C\|D\|R\|[D]\|XXP
	299	\|TWR\|Parameter 1\|●\|●\|●\|●\|●\|●
1.1	300
	301	Features
	302
	303	Write the set clock data (s) to (s)+6 to the clock data (SD100 to SD106) of the real-time clock built into the CPU module.
	304
1.2	305	\|(% colspan="3" %)Set data at all times\|(% rowspan="2" %) \|(% colspan="2" %)Special register
1.1	306	\|Element\|Project\|Clock data\|Element\|Project
	307	\|(s)\|Year (Gregorian)\|2000 to 2099 or 0 to 99\|→\|SD105\|Year (Gregorian)
	308	\|(s)+1\|Month\|1 to 12\|→\|SD104\|Month
	309	\|(s)+2\|Day\|1 to 31\|→\|SD103\|Day
	310	\|(s)+3\|Hour\|0 to 23\|→\|SD102\|Hour
	311	\|(s)+4\|Minute\|0 to 59\|→\|SD101\|Minute
	312	\|(s)+5\|Seconds\|0 to 59\|→\|SD100\|Seconds
	313	\|(s)+6\|Week\|0 (Sun) to 6 (Sat)\|→\|SD106\|Week
	314
	315	• If the TWR(P) instruction is executed, the clock data of the real-time clock is changed immediately. Therefore, the clock data after a few minutes should be transferred to the set clock data (s) to (s)+6 in advance, and the instruction will be executed when the correct time is reached.
	316
	317	• If the year in (s) is in the range of 0 to 99, it will be automatically treated as 2000 to 2099.
	318
	319	• When a value indicating an impossible time is set, the clock data will not be updated. Set the correct clock data and write again.
	320
	321	• The day of the week (SD100) is automatically corrected.
	322
	323	• The related devices are shown below.
	324
	325	\|Devices\|Content
	326	\|SD100\|The second data of the clock data is stored in BIN code.
	327	\|SD101\|The sub-data of the clock data is stored in BIN code.
	328	\|SD102\|Time data of clock data is stored in BIN code.
	329	\|SD103\|The daily data of the clock data is stored in BIN code.
	330	\|SD104\|The monthly data of the clock data is stored in BIN code.
	331	\|SD105\|The year data of the clock data is stored in a 4-digit BIN code of the Gregorian calendar.
	332	\|SD106\|The week data of the clock data is stored in BIN code. (0: day, 1: one, ..., 6: six) are stored in BIN code.
	333
1.6	334	✎Note:
1.1	335
	336	The device specified in (s) occupies 7 points. Be careful not to overlap with the device used for machine control.
	337
	338	Error code
	339
	340	\|Error code\|Content
	341	\|4085H\|When reading the specified device range exceeds the corresponding device range
	342
	343	Example
	344
	345	Set D0 date and time to 2020-2-19 12:36:00 in advance
	346
1.6	347	(% style="text-align:center" %)
	348	[[image:07-5 Basic instructions_html_994c66d1a4cbd45f.png\|\|height="57" width="305"]]
1.1	349
	350	At the moment when the time 12:36:00 arrives, turn on the M0 coil and write the time.
	351
1.6	352	(% style="text-align:center" %)
	353	[[image:07-5 Basic instructions_html_bf3e906ee5265598.png\|\|height="42" width="586"]]
1.1	354
1.6	355	== HTOS/16-bit data conversion of time data (hour, minute, second → second) ==
1.1	356
	357	HTOS(P)
	358
	359	Convert the time data stored after the device number specified in (s) into seconds and store the conversion result as BIN 16-bit data in the device specified in (d).
	360
	361	-[HTOS (s) (d)]
	362
	363	Content, range and data type
	364
	365	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	366	\|(s)\|The device start number that stores the data of the subtracted time\|-\|Signed BIN 16 bit\|ANY16_ARRAY (number of elements: 3)
	367	\|(d)\|The device start number that stores the converted clock data\|-\|Signed BIN 16 bit\|ANY16
	368
	369	Device used
	370
1.6	371	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="9" %)Devices\|Offset modification\|(((
	372	Pulse extension
1.1	373	)))
1.6	374	\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|[D]\|XXP
	375	\|(% rowspan="2" %)HTOS\|Parameter 1\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
	376	\|Parameter 2\| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
1.1	377
	378	Features
	379
	380	Convert the time data stored after the device number specified in (s) into seconds and store the conversion result in the device specified in (d).
	381
1.6	382	(% style="text-align:center" %)
	383	[[image:07-5 Basic instructions_html_a84b7741fd5bef2f.png\|\|height="130" width="550"]]
1.1	384
	385	Example
	386
	387	When 4 hours, 29 minutes and 31 seconds are specified in (s)
	388
1.6	389	(% style="text-align:center" %)
	390	[[image:07-5 Basic instructions_html_5effb7bc9b8e5cf7.png\|\|height="162" width="550"]]
1.1	391
	392	Error code
	393
	394	\|Error code\|Content
	395	\|4085H\|When reading the specified device range exceeds the corresponding device range
	396	\|4086H\|When writing the specified device range exceeds the corresponding device range
	397	\|4084H\|(((
1.6	398	When the calculation result is not in the range of 0 to 32767
1.1	399
	400	When the value specified in (s) is not in the range of 0 to 9
	401
	402	When the value specified in (s)+1 and (s)+2 is not in the range of 0 to 59
	403	)))
	404
	405	Example
	406
1.6	407	(% style="text-align:center" %)
	408	[[image:07-5 Basic instructions_html_e23e38c4ba4c34bb.png\|\|height="43" width="338"]]
1.1	409
	410	D0 time is set to 5:36:53
	411
1.6	412	(% style="text-align:center" %)
1.1	413	[[image:07-5 Basic instructions_html_2866a121e5ca5713.png]]
	414
	415	The time of D10 after the M0 coil is turned on is as below.
	416
1.6	417	(% style="text-align:center" %)
1.1	418	[[image:07-5 Basic instructions_html_1dd6c5de05890797.png]]
	419
1.6	420	== DHTOS/32-bit data conversion of time data (hour, minute, second → second) ==
1.1	421
1.6	422	DHTOS(P)
1.1	423
	424	Convert the time data stored after the device number specified in (s) into seconds and store the conversion result as BIN 32-bit data in the device specified in (d).
	425
	426	-[DHTOS (s) (d)]
	427
	428	Content, range and data type
	429
	430	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	431	\|(s)\|The device start number that stores the data of the subtracted time\|-\|Signed BIN 16 bit\|ANY16_ARRAY (number of elements: 3)
	432	\|(d)\|The device start number that stores the converted clock data\|-\|Signed BIN 32 bit\|ANY32
	433
	434	Device used
	435
1.6	436	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="9" %)Devices\|(((
	437	Offset modification
1.1	438	)))\|(((
1.6	439	Pulse extension
1.1	440	)))
1.6	441	\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|[D]\|XXP
	442	\|(% rowspan="2" %)DHTOS\|Parameter 1\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
	443	\|Parameter 2\| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
1.1	444
	445	Features
	446
	447	Convert the time data stored after the device number specified in (s) into seconds and store the conversion result in the device specified in (d).
	448
1.6	449	(% style="text-align:center" %)
	450	[[image:07-5 Basic instructions_html_f4be08508575ea01.png\|\|height="99" width="550"]]
1.1	451
	452	Example
	453
	454	When 35 hours, 10 minutes and 58 seconds are specified in (s)
	455
1.6	456	(% style="text-align:center" %)
	457	[[image:07-5 Basic instructions_html_5b9ad230ed5e1fd0.png\|\|height="125" width="550"]]
1.1	458
	459	Error code
	460
	461	\|Error code\|Content
	462	\|4085H\|When reading the specified device range exceeds the corresponding device range
	463	\|4086H\|When writing the specified device range exceeds the corresponding device range
	464	\|4084H\|(((
	465	When the calculation result is not in the range of 0 to 32767
	466
	467	When the value specified in (s)+1 and (s)+2 is not in the range of 0 to 59
	468	)))
	469
	470	Example
	471
1.6	472	(% style="text-align:center" %)
	473	[[image:07-5 Basic instructions_html_ae8ab4379e8bdb91.png\|\|height="45" width="263"]]
1.1	474
	475	D0 time is set to 15:33:24
	476
1.6	477	(% style="text-align:center" %)
	478	[[image:07-5 Basic instructions_html_57a15d9e1045e93e.png\|\|height="41" width="313"]]
1.1	479
	480	The second of D10 after the M0 coil is turned on is
	481
1.6	482	(% style="text-align:center" %)
	483	[[image:07-5 Basic instructions_html_194e906b1dc12078.png\|\|height="64" width="365"]]
1.1	484
1.6	485	HOUR/Hour measuring 16-bit
1.1	486
	487	HOUR(P)
	488
	489	The time for the input contact to be ON is measured in units of one hour.C
	490
	491	-[HOUR (s) (d1) (d2)]
	492
	493	Content, range and data type
	494
	495	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	496	\|(s)\|(((
	497	The time when the alarm (d2) is turned ON
	498
	499	(set by one hour)
	500	)))\|K0 to K32767\|Signed BIN 16 bit\|ANY16
	501	\|(d1)\|Device that stores the current value of measurement (specified data register for power failure retention)\|-\|Unsigned BIN 16 bit\|(((
	502	ANY16_ARRAY
	503
	504	(Number of elements: 2)
	505	)))
	506	\|(d2)\|Device that turns ON when the time limit expires (alarm output)\|-\|Bit\|ANY_BOOL
	507
	508	Device used
	509
1.6	510	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="17" %)Devices\|(((
	511	Offset modification
1.1	512	)))\|(((
1.6	513	Pulse extension
1.1	514	)))
1.6	515	\|Y\|M\|S\|SM\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|K\|H\|E\|[D]\|XXP
	516	\|(% rowspan="3" %)HOUR\|Parameter 1\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\| \|●\|●
	517	\|Parameter 2\| \| \| \| \| \| \| \| \| \| \| \|●\|●\|●\| \| \| \|●\|●
	518	\|Parameter 3\|●\|●\|●\|●\|●\| \| \| \| \| \| \| \| \| \| \| \| \|●\|●
1.1	519
	520	Features
	521
	522	The input contact ON time is measured in units of 1 hour. When the cumulative ON time exceeds the time (BIN 16-bit data) specified in (s), the device specified in (d2) is turned on .
	523
	524	• In (s), set the time until the alarm (d2) turns ON in units of 1 hour.
	525
	526	• (d1) stores the current measured value in units of 1 hour.
	527
	528	• If the median value of (d1) exceeds 32767, it will be modified to 32767.
	529
	530	• (d1)+1 stores the current measured value (in units of 1 second) that is less than 1 hour.
	531
	532	• (d2) turns on when the current value (d1) exceeds the time specified in (s).
	533
	534	• In order to continue to use the current value data even after the power of the CPU module is turned off, specify the data register for power failure retention to (d1). If you use general-purpose data registers, the current value data will be cleared by powering off the CPU module and STOP→RUN operations.
	535
	536	• After the alarm output specified in (d2) turns ON, measurement will continue.
	537
	538	• The measurement stops when the current value reaches the 16-bit maximum. To continue the measurement, clear the current value of (d1) to (d1)+1.
	539
1.7	540	✎Note:
1.1	541
	542	• The device specified in (d1) occupies 2 points. Be careful not to overlap with the device used for machine control.
	543
	544	• After the instruction stops running, the measurement stops and the output continues to be maintained.
	545
	546	Error code
	547
	548	\|Error code\|Content
	549	\|4085H\|When reading the specified device range exceeds the corresponding device range
	550	\|4086H\|When writing the specified device range exceeds the corresponding device range
	551	\|4084H\|When the value of (s) is negative
	552
	553	Example
	554
1.7	555	(% style="text-align:center" %)
	556	[[image:07-5 Basic instructions_html_7570f8c392470a9f.png\|\|height="45" width="320"]]
1.1	557
	558	When M0 = ON, the duration of the state is accumulated, the time is recorded in D0, and the seconds less than 1 hour are recorded in D1. When the accumulated time of D0 reaches 98 hours, the Y0 output state is ON. When the timing conditions are met, after reaching the specified value (K98), the accumulated timing will continue and the reading will continue to increase; the current time value D0 reaches the maximum value of 32767 hours and D1 reaches 3599 seconds, the timing measurement will stop. The current time values D0 and D1 are cleared to 0.
	559
1.7	560	== DHOUR/Hour measuring 32 bits ==
1.1	561
	562	DHOUR(P)
	563
	564	The time for the input contact to be ON is measured in units of one hour.
	565
	566	-[DHOUR (s) (d1) (d2)]
	567
	568	Content, range and data type
	569
	570	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	571	\|(s)\|(((
1.7	572	The time when the alarm (d2) is turned ON (set by one hour)
1.1	573	)))\|0 to 2147483647\|Signed BIN 32 bit\|ANY32
	574	\|(d1)\|Device that stores the current value of measurement (specified data register for power failure retention)\|-\|Unsigned BIN 32 bit\|(((
	575	ANY32_ARRAY
	576
	577	(Number of elements: 2)
	578	)))
	579	\|(d2)\|Device that turns ON when the time limit expires (alarm output)\|-\|Bit\|ANY_BOOL
	580
	581	Device used
	582
1.7	583	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="18" %)Devices\|(((
	584	Offset modification
1.1	585	)))\|(((
1.7	586	Pulse extension
1.1	587	)))
1.7	588	\|Y\|M\|S\|SM\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|LC\|HSC\|K\|H\|[D]\|XXP
	589	\|(% rowspan="3" %)DHOUR\|Parameter 1\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
	590	\|Parameter 2\| \| \| \| \| \| \| \| \| \| \| \|●\|●\|●\| \| \| \| \|●\|●
	591	\|Parameter 3\|●\|●\|●\|●\|●\| \| \| \| \| \| \| \| \| \| \| \| \| \|●\|●
1.1	592
	593	Features
	594
	595	• The input contact ON time is measured in units of 1 hour. When the cumulative ON time exceeds the time (BIN 32-bit data) specified in (s), the device specified in (d2) is set to ON.
	596
	597	• In (s)+1, (s), set the time until the alarm (d2) turns ON in units of 1 hour.
	598
	599	• (D1)+1 and (d1) store the current value measured in units of 1 hour. ((d1)+1: high bit, (d1): low bit)
	600
	601	• If the median of (d1)+1 and (d1) exceeds 2147483647, it will be modified to 2147483647.
	602
	603	• (D1)+2 stores the current value (in units of 1 second) of the measurement that is less than 1 hour.
	604
	605	• (D2) turns on when the current value (d1)+1, (d1) exceeds the time specified in (s).
	606
	607	• In order to continue to use the current value data even after the power of the CPU module is turned off, specify the data register for power failure retention to (d1). If you use general-purpose data registers, the current value data will be cleared by powering off the CPU module and STOP→RUN operations.
	608
	609	• After the alarm output specified in (d2) turns on, the measurement will continue.
	610
	611	• The measurement stops when the current value reaches the 32-bit maximum. To continue the measurement, clear the current value of (d1) to (d1)+2.
	612
1.7	613	✎Note:
1.1	614
	615	• The device specified in (d1) occupies 3 points. Be careful not to overlap with the device used for machine control.
	616
	617	• After the instruction stops running, the measurement stops and the output continues to be maintained.
	618
	619	Error code
	620
	621	\|Error code\|Content
	622	\|4085H\|When reading the specified device range exceeds the corresponding device range
	623	\|4086H\|When writing the specified device range exceeds the corresponding device range
	624	\|4084H\|When the value of (s) is negative
	625
	626	Example
	627
1.7	628	(% style="text-align:center" %)
	629	[[image:07-5 Basic instructions_html_3f1ef5ecc835de30.png\|\|height="43" width="448"]]
1.1	630
	631	When M0=ON, the duration of this state is accumulated, the time is recorded in D1, D0, and the seconds less than 1 hour are recorded in D2. When the accumulated time of D1, D0 reaches 1000 hours, the Y0 output state is ON. When the timing conditions are met, after reaching the specified value (K1000), the accumulated timing will continue, and the reading will continue to increase; the current time values D1 and D0 reach the maximum value of 2147483647 hours, and when D2 reaches 3599 seconds, the timing measurement will stop and the timing should be restarted. The current time values D0, D1, and D2 must be cleared to 0.
	632
1.7	633	== STOH/16-bit data conversion of time data (second → hour, minute, second) ==
1.1	634
1.7	635	STOH(P)
1.1	636
	637	Convert the second 16-bit data stored in the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.
	638
	639	-[STOH (s) (d)]
	640
	641	Content, range and data type
	642
	643	\|Parameter\|Content\|Range\|Data type\|Data type (label)
1.7	644	\|(s)\|The device start number that stores the clock data before conversion\|0 to 32767\|Signed BIN 16 bit\|ANY16
1.1	645	\|(d)\|The device start number that stores the converted clock data\|-\|Signed BIN 16 bit\|(((
1.7	646	ANY16_ARRAY (number of elements: 3)
1.1	647	)))
	648
	649	Device used
	650
1.7	651	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="9" %)Devices\|(((
	652	Offset modification
1.1	653	)))\|(((
1.7	654	Pulse extension
1.1	655	)))
1.7	656	\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|[D]\|XXP
	657	\|(% rowspan="2" %)STOH\|Parameter 1\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
	658	\|Parameter 2\| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
1.1	659
	660	Features
	661
	662	Convert the second data stored after the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.
	663
1.7	664	(% style="text-align:center" %)
	665	[[image:07-5 Basic instructions_html_1f5f3f1d80af2a34.png\|\|height="110" width="550"]]
1.1	666
	667	Example
	668
	669	When 29,011 seconds are specified in (s)
	670
1.7	671	(% style="text-align:center" %)
	672	[[image:07-5 Basic instructions_html_682516cbf773f515.png\|\|height="163" width="550"]]
1.1	673
	674	Error code
	675
	676	\|Error code\|Content
	677	\|4085H\|When reading the specified device range exceeds the corresponding device range
	678	\|4086H\|When writing the specified device range exceeds the corresponding device range
	679	\|4084H\|When the value of (s) exceeds the range
	680
	681	Example
	682
1.7	683	(% style="text-align:center" %)
	684	[[image:07-5 Basic instructions_html_e783349d57adf7d2.png\|\|height="47" width="350"]]
1.1	685
	686	Set D0 seconds to 12537
	687
	688	The hour, minute and second of D10 after the M0 coil is turned on are
	689
1.7	690	(% style="text-align:center" %)
	691	[[image:07-5 Basic instructions_html_d3c33949e8684891.png\|\|height="52" width="645"]]
1.1	692
1.7	693	== DSTOH/32-bit data conversion of time data (second → hour, minute, second) ==
1.1	694
1.7	695	DSTOH(P)
1.1	696
	697	Convert the second 32-bit data of second stored in the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.
	698
	699	-[DSTOH (s) (d)]
	700
	701	Content, range and data type
	702
	703	\|Parameter\|Content\|Range\|Data type\|Data     type (label)
	704	\|(s)\|The device start number that stores the clock data before conversion\|0 to 117964799\|Signed BIN 32 bit\|ANY32
	705	\|(d)\|The device start number that stores the converted clock data\|-\|Signed BIN 16 bit\|(((
1.7	706	ANY16_ARRAY (number of elements: 3)
1.1	707	)))
	708
	709	Device used
	710
1.7	711	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="9" %)Devices\|(((
	712	Offset modification
1.1	713	)))\|(((
1.7	714	Pulse extension
1.1	715	)))
1.7	716	\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|[D]\|XXP
	717	\|(% rowspan="2" %)DSTOH\|Parameter 1\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
	718	\|Parameter 2\| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●
1.1	719
	720	Features
	721
	722	Convert the second data stored after the device number specified in (s) into hour, minute, and second, and store the conversion result in the device specified in (d) and later.
	723
1.7	724	(% style="text-align:center" %)
	725	[[image:07-5 Basic instructions_html_cbf13fc3d10fbe61.png\|\|height="99" width="600"]]
1.1	726
	727	Example
	728
	729	When 45,325 seconds is specified in (s)
	730
1.7	731	(% style="text-align:center" %)
	732	[[image:07-5 Basic instructions_html_d6045506b13275a0.png\|\|height="135" width="600"]]
1.1	733
	734	Error code
	735
	736	\|Error code\|Content
	737	\|4085H\|When reading the specified device range exceeds the corresponding device range
	738	\|4086H\|When writing the specified device range exceeds the corresponding device range
	739	\|4084H\|When the value of (s) exceeds the range
	740
	741	Example
	742
1.7	743	(% style="text-align:center" %)
	744	[[image:07-5 Basic instructions_html_e7dd49d953db6da4.png\|\|height="39" width="316"]]
1.1	745
	746	Set D0 seconds to 2152537
	747
	748	The hour, minute and second of D10 after the M0 coil is turned on are
	749
1.7	750	(% style="text-align:center" %)
	751	[[image:07-5 Basic instructions_html_10d57bde1ac0a218.png\|\|height="52" width="661"]]
1.1	752
1.7	753	== TCMP/Clock data comparison ==
1.1	754
	755	TCMP(P)
	756
	757	Compare the comparison time specified in (s1), (s2), (s3) with the time data specified in (s4), and turn the bit device specified in (d) ON/OFF according to their size match.
	758
	759	-[TCMP (s1) (s2) (s3) (s4) (d)]
	760
	761	Content, range and data type
	762
	763	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	764	\|(s1)\|Specify the "hour" of the comparison base time.\|0 to 23\|Signed BIN 16 bit\|ANY16
	765	\|(s2)\|Specify the "minute" of the comparison base time.\|0 to 59\|Signed BIN 16 bit\|ANY16
	766	\|(s3)\|Specify the "second" of the comparison base time.\|0 to 59\|Signed BIN 16 bit\|ANY16
	767	\|(s4)\|Specify the "hour" of the time data (hour, minute, second).\|-\|Signed BIN 16 bit\|ANY16_ARRAY
	768	\|(d)\|The bit device is turned ON/OFF according to the comparison result.\|-\|Bit\|ANYBIT_ARRAY
	769
	770	Device used
	771
1.7	772	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="17" %)Devices\|(((
	773	Offset modification
1.1	774	)))\|(((
1.7	775	Pulse extension
1.1	776	)))
1.7	777	\|Y\|M\|S\|SM\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|K\|H\|E\|[D]\|XXP
	778	\|(% rowspan="5" %)TCMP\|Parameter 1\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\| \|●\|●
	779	\|Parameter 2\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\| \|●\|●
	780	\|Parameter 3\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\|●\| \|●\|●
	781	\|Parameter 4\| \| \| \| \| \| \| \| \| \|●\|●\|●\|●\|●\| \| \| \|●\|●
	782	\|Parameter 5\|●\|●\|●\|●\|●\| \| \| \| \| \| \| \| \| \| \| \| \|●\|●
1.1	783
	784	Features
	785
	786	Compare the time of the reference time (hour, minute, second) [(s1), (s2), (s3)] with the time data (hour, minute, second) [(s4), (s4)+1, (s4) +2] Compare the size and turn on/off the 3 points from (d) according to the result of the same size.
	787
1.8	788	(% style="text-align:center" %)
	789	[[image:07-5 Basic instructions_html_5df7ad3057fada12.png\|\|height="385" width="750"]]
1.1	790
1.8	791	✎Note:
1.1	792
	793	The device specified in (s4) and (d) occupies 3 points. Be careful not to overlap with the device used for machine control.
	794
	795	When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.
	796
	797	Error code
	798
	799	\|Error code\|Content
	800	\|4085H\|When reading the specified device range exceeds the corresponding device range
	801	\|4086H\|When writing the specified device range exceeds the corresponding device range
	802	\|4084H\|(((
	803	When the value specified in (s) and (s4) is not in the range of 0 to 23
	804
1.8	805	When the value specified in (s2),(s3) (s4)+1 and (s4)+2 is not in the range of 0 to 59
1.1	806	)))
	807
	808	Example
	809
1.8	810	(% style="text-align:center" %)
	811	[[image:07-5 Basic instructions_html_fcc16317cf7c0700.png\|\|height="68" width="359"]]
1.1	812
	813	Set D10 to 1, D11 to 30, D12 to 0
	814
	815	When M0 is turned on, the time that D23 will come is 0:31:27
	816
1.8	817	(% style="text-align:center" %)
	818	[[image:07-5 Basic instructions_html_de97dd7a612b2323.png\|\|height="50" width="653"]]
1.1	819
	820	M10 is turned ON
	821
1.8	822	(% style="text-align:center" %)
	823	[[image:07-5 Basic instructions_html_56e2d606adc09fd.png\|\|height="52" width="239"]]
1.1	824
1.8	825	== TZCP/Clock data bandwidth comparison ==
1.1	826
1.8	827	TZCP(P)
1.1	828
	829	Compare the comparison time of the high and low points specified in (s1) and (s2) with the time data specified in (s3), and turn the bit device specified in (d) ON/OFF according to its size and bandwidth.
	830
	831	-[TZCP (s1) (s2) (s3) (d)]
	832
	833	Content, range and data type
	834
	835	\|Parameter\|Content\|Range\|Data type\|Data type (label)
	836	\|(s1)\|Specify the "hour" of the lower limit time (hour, minute, second)\|-\|Signed BIN 16 bit\|(((
1.8	837	ANY16_ARRAY (number of elements: 3)
1.1	838	)))
	839	\|(s2)\|Specify the "hour" of the lower limit time (hour, minute, second)\|-\|Signed BIN 16 bit\|(((
1.8	840	ANY16_ARRAY (number of elements: 3)
1.1	841	)))
	842	\|(s3)\|Specify "hour" of time data (hour, minute, second)\|-\|Signed BIN 16 bit\|(((
1.8	843	ANY16_ARRAY (number of elements: 3)
1.1	844	)))
	845	\|(d)\|The bit device is turned ON/OFF according to the comparison result.\|-\|Bit\|(((
1.8	846	ANY16_ARRAY (number of elements: 3)
1.1	847	)))
	848
	849	Device used
	850
1.8	851	\|(% rowspan="2" %)Instruction\|(% rowspan="2" %)Parameter\|(% colspan="10" %)Devices\|Offset modification\|(((
	852	Pulse extension
1.1	853	)))
1.8	854	\|Y\|M\|S\|SM\|D.b\|T\|C\|D\|R\|SD\|[D]\|XXP
	855	\|(% rowspan="4" %)TZCP\|Parameter 1\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●
	856	\|Parameter 2\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●
	857	\|Parameter 3\| \| \| \| \| \|●\|●\|●\|●\|●\|●\|●
	858	\|Parameter 4\|●\|●\|●\|●\|●\| \| \| \| \| \|●\|●
1.1	859
	860	Features
	861
	862	Compare the comparison time of the high and low points specified in (s1) and (s2) with the time data specified in (s3), and turn the bit device specified in (d) ON/OFF according to its size and bandwidth.
	863
1.8	864	(% style="text-align:center" %)
	865	[[image:07-5 Basic instructions_html_844291270080313d.png\|\|height="339" width="750"]]
1.1	866
1.8	867	✎Note:
1.1	868
	869	• The devices specified in (s1), (s2), (s3), (d) occupy 3 points. Be careful not to overlap with the device used for machine control.
	870
	871	• When using the clock data time (hour, minute, second) of the built-in real-time clock of the CPU module, use the TRD(P) instruction to read the value of the special register and assign the word device to each operand.
	872
	873	• When (s1)> (s2), two of (d), (d)+1, (d)+2 are ON/OFF.
	874
	875	Error code
	876
	877	\|Error code\|Content
	878	\|4085H\|When reading the specified device range exceeds the corresponding device range
	879	\|4086H\|When writing the specified device range exceeds the corresponding device range
	880	\|4084H\|(((
	881	When the value specified in (s1), (s2) and (s3) is not in the range of 0 to 23
	882
	883	When the value specified in (s1)+1, (s2)+1, (s3)+1, (s1)+2, (s2)+2 and (s3)+2 is not in the range of 0 to 59
	884	)))
	885
	886	Example
	887
1.8	888	(% style="text-align:center" %)
	889	[[image:07-5 Basic instructions_html_30027a2387c26c2e.png\|\|height="46" width="439"]]
1.1	890
	891	Set D0 time to 16:30:00 and D10 time to 4:30:0
	892
1.8	893	(% style="text-align:center" %)
	894	[[image:07-5 Basic instructions_html_c64e0faf2af172f8.png\|\|height="49" width="626"]]
1.1	895
1.8	896	(% style="text-align:center" %)
	897	[[image:07-5 Basic instructions_html_66e3a2eadeb2ecbb.png\|\|height="50" width="625"]]
1.1	898
	899	After the coil is turned on, the reading time to D20 time is 8:30:00
	900
1.8	901	(% style="text-align:center" %)
	902	[[image:07-5 Basic instructions_html_75c44dad07eaf80a.png\|\|height="49" width="625"]]
1.1	903
	904	M0/M12 is ON
	905
1.8	906	(% style="text-align:center" %)
	907	[[image:07-5 Basic instructions_html_f512f36261705953.png\|\|height="48" width="218"]]
11.1	908
	909
12.1	910	== TON/BIN 16-bit Turn-on delay timer ==
11.1	911
12.1	912	TON(P)
11.1	913
	914	Specify the T timer device in (s1), the expected time in (s2), and the time base (resolution) in (s3). And the result of the measured individual time interval operation is stored in the device specified in (s1).
	915
	916	PLC Editor2 version that supports this instruction: 2.3.1 and above.
	917
	918	-[TON (s1) (s2) (s3)]
	919
	920	Content, scope, data type
	921
	922	\|parameter\|Content\|range\|type of data\|Data type (label)
	923	\|(s1)\|T device\|0~~511\|Signed BIN 16 bit\|ANY16_S
	924	\|(s2)\|Expected time\|0~~32767\|Signed BIN 16 bit\|ANY16_S
	925	\|(s3)\|Time base(resolution)\|1/10/100/1000/10000\|Signed BIN 16 bit\|ANY16_S
	926
	927	Device used
	928
	929	\|(% rowspan="2" %)instruction\|(% rowspan="2" %)parameter\|(% colspan="24" %)Devices\|Offset modification\|Pulse extension
	930	\|X\|Y\|M\|S\|SM\|T(bit)\|C(bit)\|LC(bit)\|HSC(bit)\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|LC\|HSC\|K\|H\|E\|[D]\|XXP
	931	\|(% rowspan="3" %)TON\|Parameter 1\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\| \| \| \| \| \| \| \| \| \| \|
	932	\|Parameter 2\| \| \| \| \| \| \| \| \| \| \|●\|●\|●\|●\| \|●\|●\|●\|●\| \| \|●\|●\| \| \|
	933	\|Parameter 3\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\|●\| \| \|
	934
	935	Timing Chart
	936
21.1	937	(% style="text-align:center" %)
26.1	938	[[image:图片3.png]]
11.1	939
13.1	940	Features
	941
11.1	942	1) When the timer starts timing, the instruction after the timer starts to run when the timing time is greater than the time value of "the product of S2 and S3".
	943
	944	2) When the timer value is greater than 0 and less than the time value of "the product of S2 and S3", the timer will stop whenever the contact is disconnected, and when the contact is connected, the timer will start timing again.
	945
	946
	947	\|S3 time base\|Actual value
	948	\|1\|100us
	949	\|10\|1ms
	950	\|100\|10ms
	951	\|1000\|100ms
	952	\|10000\|1s
	953
	954	Precautions
	955
	956	• Avoid timer number conflict: the same timer number cannot be used for TON, TONR, TOF, TP, OUT_T timers at the same time. For example, TON T32 and TOF T32 cannot be used at the same time (it may cause data confusion and not achieve the effect of the corresponding instruction function).
	957
	958	Error code
	959
	960	\|Error code\|Content
	961	\|4084H\|Input data in (s2) (s3) is outside the specified range.
	962	\|4085H\|Device tpye in (s1) (s2) (s3) is outside the specified range.
	963	\|4086H\|Device tpye in (s1) is outside the specified range.
	964
12.1	965	Example
11.1	966
21.1	967	(% style="text-align:center" %)
26.1	968	[[image:图片4.png]]
11.1	969
	970	T1 is used for storing time, setting the expected time as K10 and the time base as K10000.
	971
	972	After set on (M8) contact and waiting for the value in the turn-on delay timer (T1) to reach the estimated time of 10s, the contact of (T1) on and output Y0.
	973
	974	If the (M8) contact is off in the process of turn-on delay timer (T1) timing, the turn-on delay timer (T1) value is cleared to 0 and the timing ends.
16.1	975
	976	== TONR/BIN 16-bit Hold-type turn-on delay timer ==
	977
20.1	978	TONR(P)
16.1	979
	980	Specify the T timer device in (s1), the expected time in (s2), and the time base (resolution) in (s3). And store the time values of the accumulated multiple timing intervals into the device specified in (s1).
	981
	982	PLC Editor2 version that supports this instruction: 2.3.1 and above.
	983
	984	-[TONR (s1) (s2) (s3)]
	985
	986	Content, scope, data type
	987
	988	\|parameter\|Content\|range\|type of data\|Data type (label)
	989	\|(s1)\|T device\|0~~511\|Signed BIN 16 bit\|ANY16_S
	990	\|(s2)\|Expected time\|0~~32767\|Signed BIN 16 bit\|ANY16_S
	991	\|(s3)\|Time base(resolution)\|1/10/100/1000/10000\|Signed BIN 16 bit\|ANY16_S
	992
	993	Device used
	994
	995	\|(% rowspan="2" %)instruction\|(% rowspan="2" %)parameter\|(% colspan="24" %)Devices\|Offset modification\|Pulse extension
	996	\|X\|Y\|M\|S\|SM\|T(bit)\|C(bit)\|LC(bit)\|HSC(bit)\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|LC\|HSC\|K\|H\|E\|[D]\|XXP
	997	\|(% rowspan="3" %)TON\|Parameter 1\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\| \| \| \| \| \| \| \| \| \| \|
	998	\|Parameter 2\| \| \| \| \| \| \| \| \| \| \|●\|●\|●\|●\| \|●\|●\|●\|●\| \| \|●\|●\| \| \|
	999	\|Parameter 3\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\|●\| \| \|
	1000
	1001	Timing Chart
	1002
20.1	1003	(% style="text-align:center" %)
25.1	1004	[[image:图片2.png]]
16.1	1005
	1006	Features
	1007
	1008	1) When the timer starts timing, the instruction after the timer starts to run when the timing time is greater than the time value of "the product of S2 and S3".
	1009
	1010	2) When the coil in front of the timer is off, the TONR timer saves the current value. When the coil is on, the TONR timer continues to timing.
	1011
	1012	3) The current value of TONR can be cleared using the reset command. After the preset time is reached, TONR maintains the current value of the timer.
	1013
	1014
	1015	\|S3 time base\|Actual value
	1016	\|1\|100us
	1017	\|10\|1ms
	1018	\|100\|10ms
	1019	\|1000\|100ms
	1020	\|10000\|1s
	1021
	1022	Precautions
	1023
	1024	• Avoid timer number conflict: the same timer number cannot be used for TON, TONR, TOF, TP, OUT_T timers at the same time. For example, TON T32 and TOF T32 cannot be used at the same time (it may cause data confusion and not achieve the effect of the corresponding instruction function).
	1025
	1026	Error code
	1027
	1028	\|Error code\|Content
	1029	\|4084H\|Input data in (s2) (s3) is outside the specified range.
	1030	\|4085H\|Device tpye in (s1) (s2) (s3) is outside the specified range.
	1031	\|4086H\|Device tpye in (s1) is outside the specified range.
	1032
	1033	Example
	1034
20.1	1035	(% style="text-align:center" %)
25.1	1036	[[image:图片1.png]]
16.1	1037
	1038	T1 is used for storing time, setting the expected time as K10 and the time base as K10000.
	1039
	1040	When the (M8) contact off and on again during timing. (T1) maintains the value at the last disconnection and continues timing until the estimated time of 10s. After the estimated time is reached, the (T1) contact on and output Y0. If the (M8) contact off in this time, the (T1) contact is still ON but Y0 is off.
	1041
	1042	When (M0) contact turn ON, the (T1) timer value is cleared to 0 with the RST reset command, the (T1) contact is off, and the Y0 OFF.
	1043
	1044	== TOF/BIN 16-bit Turn-off delay timer ==
	1045
19.1	1046	TOF(P)
16.1	1047
	1048	Specify the T timer device in (s1), the expected time in (s2), and the time base (resolution) in (s3). And store the time values of the accumulated multiple timing intervals into the device specified in (s1).
	1049
	1050	PLC Editor2 version that supports this instruction: 2.3.1 and above.
	1051
	1052	-[TOF (s1) (s2) (s3)]
	1053
	1054	Content, scope, data type
	1055
	1056	\|parameter\|Content\|range\|type of data\|Data type (label)
	1057	\|(s1)\|T device\|0~~511\|Signed BIN 16 bit\|ANY16_S
	1058	\|(s2)\|Expected time\|0~~32767\|Signed BIN 16 bit\|ANY16_S
	1059	\|(s3)\|Time base(resolution)\|1/10/100/1000/10000\|Signed BIN 16 bit\|ANY16_S
	1060
	1061	Device used
	1062
	1063	\|(% rowspan="2" %)instruction\|(% rowspan="2" %)parameter\|(% colspan="24" %)Devices\|Offset modification\|Pulse extension
	1064	\|X\|Y\|M\|S\|SM\|T(bit)\|C(bit)\|LC(bit)\|HSC(bit)\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|LC\|HSC\|K\|H\|E\|[D]\|XXP
	1065	\|(% rowspan="3" %)TON\|Parameter 1\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\| \| \| \| \| \| \| \| \| \| \|
	1066	\|Parameter 2\| \| \| \| \| \| \| \| \| \| \|●\|●\|●\|●\| \|●\|●\|●\|●\| \| \|●\|●\| \| \|
	1067	\|Parameter 3\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\|●\| \| \|
	1068
	1069	Timing Chart
	1070
19.1	1071	(% style="text-align:center" %)
27.1	1072	[[image:图片5.png]]
16.1	1073
	1074	Features
	1075
	1076	1) After the input is disconnected, the output is delayed for a fixed time before stopping. The timer bit turns on immediately when the input is started and the current value is set to 0. When the input is disconnected, timing starts until the current time is equal to the preset time, then timing stops.
	1077
	1078	2) When the preset value is reached, the timer bit is disconnected and the current value stops incrementing; If the input is turned on again before the TOF reaches the preset value, the timer bit remains on.
	1079
	1080	3) For the TOF timer to start timing, the enable input must perform an on-off transition.
	1081
	1082
	1083	\|S3 time base\|Actual value
	1084	\|1\|100us
	1085	\|10\|1ms
	1086	\|100\|10ms
	1087	\|1000\|100ms
	1088	\|10000\|1s
	1089
	1090	Precautions
	1091
	1092	• Avoid timer number conflict: the same timer number cannot be used for TON, TONR, TOF, TP, OUT_T timers at the same time. For example, TON T32 and TOF T32 cannot be used at the same time (it may cause data confusion and not achieve the effect of the corresponding instruction function).
	1093
	1094	Error code
	1095
	1096	\|Error code\|Content
	1097	\|4084H\|Input data in (s2) (s3) is outside the specified range.
	1098	\|4085H\|Device tpye in (s1) (s2) (s3) is outside the specified range.
	1099	\|4086H\|Device tpye in (s1) is outside the specified range.
	1100
	1101	Example
	1102
19.1	1103	(% style="text-align:center" %)
27.1	1104	[[image:图片6.png]]
16.1	1105
	1106	T1 is used for storing time, setting the expected time as K10 and the time base as K10000.
	1107
	1108	Make the (M8) contact ON and oFF, When (M8) ON, (T1) contact is ON and Y0 is ON. when (M8) OFF, (Y0) is OFF and (T1) starts timing. When the estimated time of 5s is reached, the (T1) contact is also 0FF.
	1109
	1110	If the (M8) contact ON again during (T1) timing, the (T1) value clears to 0 and the timing ends
	1111
17.1	1112	== TP/BIN 16-bit Start pulse timer ==
	1113
18.1	1114	TP(P)
17.1	1115
	1116	Specify the T timer device in (s1), the expected time in (s2), and the time base (resolution) in (s3). And output TRUE in the set time of "(s2)*(s3)" product.
	1117
	1118	PLC Editor2 version that supports this instruction: 2.3.1 and above.
	1119
	1120	-[TP (s1) (s2) (s3)]
	1121
	1122	Content, scope, data type
	1123
	1124	\|parameter\|Content\|range\|type of data\|Data type (label)
	1125	\|(s1)\|T device\|0~~511\|Signed BIN 16 bit\|ANY16_S
	1126	\|(s2)\|Expected time\|0~~32767\|Signed BIN 16 bit\|ANY16_S
	1127	\|(s3)\|Time base(resolution)\|1/10/100/1000/10000\|Signed BIN 16 bit\|ANY16_S
	1128
	1129	Device used
	1130
	1131	\|(% rowspan="2" %)instruction\|(% rowspan="2" %)parameter\|(% colspan="24" %)Devices\|Offset modification\|Pulse extension
	1132	\|X\|Y\|M\|S\|SM\|T(bit)\|C(bit)\|LC(bit)\|HSC(bit)\|D.b\|KnX\|KnY\|KnM\|KnS\|T\|C\|D\|R\|SD\|LC\|HSC\|K\|H\|E\|[D]\|XXP
	1133	\|(% rowspan="3" %)TON\|Parameter 1\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\| \| \| \| \| \| \| \| \| \| \|
	1134	\|Parameter 2\| \| \| \| \| \| \| \| \| \| \|●\|●\|●\|●\| \|●\|●\|●\|●\| \| \|●\|●\| \| \|
	1135	\|Parameter 3\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|●\|●\| \| \|
	1136
	1137	Timing Chart
	1138
18.1	1139	(% style="text-align:center" %)
28.1	1140	[[image:图片7.png]]
17.1	1141
	1142	Features
	1143
	1144	Timer that outputs TRUE only for the set time after startup
	1145
	1146	1) When the enable input is turned on, timer (s1) is started and timer (s1) bit is immediately turned on. Timer (s1) stops as time increases and reaches the expected time.
	1147
	1148	2) After timer (s1) reaches the predetermined time (s2), timer (s1) bit is disconnected. At this time, timer (s1) stops increasing. If the enable input becomes FALSE, timer (s1) will reset. The expected time (s2) becomes 0.
	1149
	1150	3) After starting, if the enable input becomes FALSE before the timer (s1) reaches the expected time (s2), the timer will be reset after reaching the expected time (s2).
	1151
	1152
	1153	\|S3 time base\|Actual value
	1154	\|1\|100us
	1155	\|10\|1ms
	1156	\|100\|10ms
	1157	\|1000\|100ms
	1158	\|10000\|1s
	1159
	1160	Precautions
	1161
	1162	• Avoid timer number conflict: the same timer number cannot be used for TON, TONR, TOF, TP, OUT_T timers at the same time. For example, TON T32 and TOF T32 cannot be used at the same time (it may cause data confusion and not achieve the effect of the corresponding instruction function).
	1163
	1164	Error code
	1165
	1166	\|Error code\|Content
	1167	\|4084H\|Input data in (s2) (s3) is outside the specified range.
	1168	\|4085H\|Device tpye in (s1) (s2) (s3) is outside the specified range.
	1169	\|4086H\|Device tpye in (s1) is outside the specified range.
	1170
	1171	Example
	1172
18.1	1173	(% style="text-align:center" %)
28.1	1174	[[image:图片8.png]]
17.1	1175
	1176	T1 is used for storing time, setting the expected time as K5 and the time base as K10000.
	1177
	1178	When the enable input (M8) is on, the timer (T1) is started and the timer (T1) bit turns on immediately. Timer (T1) stops as time increases and reaches the expected time.
	1179
	1180	After timer (T1) reaches a predetermined time of 5s, timer (T1) bit is disconnected. At this time, timer (T1) stops increasing. If the enable input (M8) becomes FALSE, timer (T1) will reset. The expected time becomes 0.
	1181
	1182	After startup, if the enable input (M8) becomes FALSE before the timer (T1) reaches the estimated time of 5s, the timer will be reset after reaching the estimated time of 5s.