Skip to Content

Changes for page 06 Control Mode

Last modified by Mora Zhou on 2023/12/21 15:45
From version 8.1
edited by Mora Zhou
on 2023/11/21 13:49
Change comment: There is no comment for this version
To version 10.1
edited by Mora Zhou
on 2023/11/21 13:53
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -19,17 +19,13 @@
19 19  )))
20 20  |5|The servo drive and motor are grounded reliably.
21 21  |6|(((
22 -The jumper between terminals C and D has been removed when the
23 -
24 -external regenerative resistor is used.
22 +The jumper between terminals C and D has been removed when the external regenerative resistor is used.
25 25  )))
26 26  |7|The cable tension is within the permissible range.
27 27  |8|The wiring terminals have been insulated.
28 28  |(% colspan="2" %)Environment and mechanical conditions
29 29  |1|(((
30 -No foreign objects, such as wire end or metal powder, which may cause
31 -
32 -short circuit of the signal wire and power cables, exist inside and outside of the servo drive.
28 +No foreign objects, such as wire end or metal powder, which may cause short circuit of the signal wire and power cables, exist inside and outside of the servo drive.
33 33  )))
34 34  |2|The servo drive or external regenerative resistor is not placed on flammable objects.
35 35  |3|Installation and shaft and mechanical connection are reliable.
... ... @@ -269,17 +269,15 @@
269 269  
270 270  11: INH, Position reference inhibited
271 271  
272 -12: VSSEL, Damp control switch(not implemented yet)
268 +12: VSSEL, Damp control switch(Not implemented yet)
273 273  
274 -13: INSPD1, Internal speed command selection 1(not implemented yet)
270 +13: INSPD1, Internal speed command selection 1(Not implemented yet)
275 275  
276 -14: INSPD2, Internal speed command selection 2
272 +14: INSPD2, Internal speed command selection 2(Not implemented yet)
277 277  
278 -(not implemented yet)
274 +15: INSPD3, Internal speed command selection 3(Not implemented yet)
279 279  
280 -15: INSPD3, Internal speed command selection 3(not implemented yet)
281 -
282 -16: J-SEL, Inertia ratio switch(not implemented yet)
276 +16: J-SEL, Inertia ratio switch(Not implemented yet)
283 283  )))|-|03-POT
284 284  |(% style="width:73px" %)P6-9|(% style="width:134px" %)DI_3 logic selection|(% style="width:114px" %)During running|(% style="width:85px" %)(((
285 285  Power-on
... ... @@ -288,9 +288,9 @@
288 288  )))|(% style="width:69px" %)0~~1|(% style="width:490px" %)(((
289 289  DI port input logic validity function selection.
290 290  
291 -0: Normal open input. Active when off (switch closed).
285 +0: Normal open input. Active when off (Switch closed).
292 292  
293 -1: Normal closed input. Active when on (switch open).
287 +1: Normal closed input. Active when on (Switch open).
294 294  )))|-|0
295 295  |(% style="width:73px" %)P6-10|(% style="width:134px" %)DI_3 input source selection|(% style="width:114px" %)During running|(% style="width:85px" %)(((
296 296  Power-on