Skip to Content

Wiki source code of 07 Adjustments

Version 70.1 by Mora Zhou on 2024/07/17 13:59
Show last authors
1 = **Overview** =
2
3 The servo drive needs to make the motor faithfully operate in accordance with the instructions issued by the upper controller without delay as much as possible. In order to make the motor action closer to the instruction and maximize the mechanical performance, gain adjustment is required. The process of gain adjustment is shown in Figure 7-1.
4
5 (% style="text-align:center" %)
6 (((
7 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
8 [[**Figure 7-1 Gain adjustment process**>>image:image-20220608174118-1.png||id="Iimage-20220608174118-1.png"]]
9 )))
10
11 The servo gain is composed of multiple sets of parameters such as position loop, speed loop, filter, load inertia ratio, etc., and they affect each other. In the process of setting the servo gain, the balance between the setting values of each parameter must be considered.
12
13 (% class="box infomessage" %)
14 (((
15 ✎**Note: **Before adjusting the gain, it is recommended to perform a jog trial run first to ensure that the servo motor can operate normally! The gain adjustment process description is shown in the table below.
16 )))
17
18 (% class="table-bordered" style="margin-right:auto" %)
19 |=(% colspan="3" style="text-align: center; vertical-align: middle;" %)**Gain adjustment process**|=(% style="text-align: center; vertical-align: middle;" %)**Function**|=(% style="text-align: center; vertical-align: middle;" %)**Detailed chapter**
20 |(% style="text-align:center; vertical-align:middle" %)1|(% colspan="2" style="text-align:center; vertical-align:middle" %)Online inertia recognition|(% style="text-align:center; vertical-align:middle" %)Use the host computer debugging platform software matched with the drive to automatically identify the load inertia ratio. With its own inertia identification function, the drive automatically calculates the load inertia ratio.|(% style="text-align:center; vertical-align:middle" %)__[[7.2>>||anchor="HInertiarecognition"]]__
21 |(% style="text-align:center; vertical-align:middle" %)2|(% colspan="2" style="text-align:center; vertical-align:middle" %)Automatic gain adjustment|On the premise of setting the inertia ratio correctly, the drive automatically adjusts a set of matching gain parameters.|(% style="text-align:center; vertical-align:middle" %)__[[7.3.1>>||anchor="HAutomaticgainadjustment"]]__
22 |(% rowspan="3" style="text-align:center; vertical-align:middle" %)3|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Manual gain adjustment|(% style="text-align:center; vertical-align:middle" %)Basic gain|On the basis of automatic gain adjustment, if the expected effect is not achieved, manually fine-tune the gain to optimize the effect.|(% style="text-align:center; vertical-align:middle" %)__[[7.3.2>>||anchor="HManualgainadjustment"]]__
23 |(% style="text-align:center; vertical-align:middle" %)Feedforward gain|The feedforward function is enabled to improve the followability.|(% style="text-align:center; vertical-align:middle" %)__[[7.3.3>>||anchor="HFeedforwardgain"]]__
24 |(% style="text-align:center; vertical-align:middle" %)Model tracking control|Enable model tracking control, shortening the responding time and improving followability.|(% style="text-align:center; vertical-align:middle" %)7.3.4
25 |(% colspan="1" rowspan="3" style="text-align:center; vertical-align:middle" %)4|(% colspan="1" rowspan="3" style="text-align:center; vertical-align:middle" %)Vibration suppression|(% style="text-align:center; vertical-align:middle" %)Mechanical resonance|The notch filter function is enabled to suppress mechanical resonance.|(% style="text-align:center; vertical-align:middle" %)__[[7.4.1>>||anchor="HMechanicalresonancesuppressionmethods"]]__
26 |Low frequency vibration suppression|Enable low frequency vibration suppression|7.4.3
27 |Type A vibration suppression|Enable type A vibration suppression|7.4.4
28
29 Table 7-1 Description of gain adjustment process
30
31 = **Inertia recognition** =
32
33 Load inertia ratio P03-01 refers to:
34
35 (% style="text-align:center" %)
36 [[image:image-20220611152902-1.png||class="img-thumbnail"]]
37
38 The load inertia ratio is an important parameter of the servo system, and setting of the load inertia ratio correctly helps to quickly complete the debugging. The load inertia ratio could be set manually, and online load inertia recognition could be performed through the host computer debugging software.
39
40 (% class="warning" %)|(((
41 (% style="text-align:center" %)
42 [[image:image-20220611152918-2.png]]
43 )))
44 |(((
45 **Before performing online load inertia recognition, the following conditions should be met:**
46
47 * The maximum speed of the motor should be greater than 300rpm;
48 * The actual load inertia ratio is between 0.00 and 100.00;
49 * The load torque is relatively stable, and the load cannot change drastically during the measurement process;
50 * The backlash of the load transmission mechanism is within a certain range;
51
52 **The motor's runable stroke should meet two requirements:**
53
54 * There is a movable stroke of more than 1 turn in both forward and reverse directions between the mechanical limit switches.
55 * Before performing online inertia recognition, please make sure that the limit switch has been installed on the machine, and that the motor has a movable stroke of more than 1 turn each in the forward and reverse directions to prevent overtravel during the inertia recognition process and cause accidents.
56 * Meet the requirement of inertia recognition turns P03-05.
57 * Make sure that the motor's runable stroke at the stop position is greater than the set value of the number of inertia recognition circles P03-05, otherwise the maximum speed of inertia recognition P03-06 should be appropriately reduced.
58 * During the automatic load inertia recognition process, if vibration occurs, the load inertia recognition should be stopped immediately.
59 )))
60
61 The related function codes are shown in the table below.
62
63 (% class="table-bordered" %)
64 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 117px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 136px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 173px;" %)(((
65 **Setting method**
66 )))|=(% style="text-align: center; vertical-align: middle; width: 168px;" %)(((
67 **Effective time**
68 )))|=(% style="text-align: center; vertical-align: middle; width: 125px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 118px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 276px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
69 |=(% style="text-align: center; vertical-align: middle; width: 117px;" %)P03-01|(% style="text-align:center; vertical-align:middle; width:136px" %)Load inertia ratio|(% style="text-align:center; vertical-align:middle; width:173px" %)(((
70 Operation setting
71 )))|(% style="text-align:center; vertical-align:middle; width:168px" %)(((
72 Effective immediately
73 )))|(% style="text-align:center; vertical-align:middle; width:125px" %)300|(% style="text-align:center; vertical-align:middle; width:118px" %)100 to 10000|(% style="width:276px" %)Set load inertia ratio, 0.00 to 100.00 times|(% style="text-align:center; vertical-align:middle" %)0.01
74 |=(% style="text-align: center; vertical-align: middle; width: 117px;" %)P03-05|(% style="text-align:center; vertical-align:middle; width:136px" %)(((
75 Inertia recognition turns
76 )))|(% style="text-align:center; vertical-align:middle; width:173px" %)(((
77 Shutdown setting
78 )))|(% style="text-align:center; vertical-align:middle; width:168px" %)(((
79 Effective immediately
80 )))|(% style="text-align:center; vertical-align:middle; width:125px" %)2|(% style="text-align:center; vertical-align:middle; width:118px" %)1 to 20|(% style="width:276px" %)Offline load inertia recognition process, motor rotation number setting|(% style="text-align:center; vertical-align:middle" %)circle
81 |=(% style="text-align: center; vertical-align: middle; width: 117px;" %)P03-06|(% style="text-align:center; vertical-align:middle; width:136px" %)(((
82 Inertia recognition maximum speed
83 )))|(% style="text-align:center; vertical-align:middle; width:173px" %)(((
84 Shutdown setting
85 )))|(% style="text-align:center; vertical-align:middle; width:168px" %)(((
86 Effective immediately
87 )))|(% style="text-align:center; vertical-align:middle; width:125px" %)1000|(% style="text-align:center; vertical-align:middle; width:118px" %)300 to 2000|(% style="width:276px" %)(((
88 Set the allowable maximum motor speed instruction in offline inertia recognition mode.
89
90 The faster the speed during inertia recognition, the more accurate the recognition result will be. Usually, you can keep the default value.
91 )))|(% style="text-align:center; vertical-align:middle" %)rpm
92 |=(% style="text-align: center; vertical-align: middle; width: 117px;" %)P03-07|(% style="text-align:center; vertical-align:middle; width:136px" %)(((
93 Parameter recognition rotation direction
94 )))|(% style="text-align:center; vertical-align:middle; width:173px" %)(((
95 Shutdown setting
96 )))|(% style="text-align:center; vertical-align:middle; width:168px" %)(((
97 Effective immediately
98 )))|(% style="text-align:center; vertical-align:middle; width:125px" %)0|(% style="text-align:center; vertical-align:middle; width:118px" %)0 to 2|(% style="width:276px" %)(((
99 0: Forward and reverse reciprocating rotation
100
101 1: Forward one-way rotation
102
103 2: Reverse one-way rotation
104 )))|(% style="text-align:center; vertical-align:middle" %)-
105
106 Table 7-2 Related parameters of gain adjustment
107
108 = **Gain adjustment** =
109
110 In order to optimize the responsiveness of the servo drive, the servo gain set in the servo drive needs to be adjusted. Servo gain needs to set multiple parameter combinations, which will affect each other. Therefore, the adjustment of servo gain must consider the relationship between each parameter.
111
112 Under normal circumstances, high-rigidity machinery can improve the response performance by increasing the servo gain. But for machines with lower rigidity, when the servo gain is increased, vibration may occur, and then affects the increase in gain. Therefore, selecting appropriate servo gain parameters can achieve higher response and stable performance.
113
114 The servo supports automatic gain adjustment and manual gain adjustment. It is recommended to use automatic gain adjustment first.
115
116 == Automatic gain adjustment ==
117
118 Automatic gain adjustment means that through the rigidity level selection function P03-02, the servo drive will automatically generate a set of matching gain parameters to meet the requirements of rapidity and stability.
119
120 The rigidity of the servo refers to the ability of the motor rotor to resist load inertia, that is, the self-locking ability of the motor rotor. The stronger the servo rigidity, the larger the corresponding position loop gain and speed loop gain, and the faster the response speed of the system.
121
122 (% class="table-bordered" style="margin-right:auto" %)
123 (% class="warning" %)|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611152630-1.png]]
124 |(% style="text-align:left; vertical-align:middle" %)Before adjusting the rigidity grade, set the appropriate load inertia ratio P03-01 correctly.
125
126 The value range of the rigidity grade is between 0 and 31. Grade 0 corresponds to the weakest rigidity and minimum gain, and grade 31 corresponds to the strongest rigidity and maximum gain. According to different load types, the values in the table below are for reference.
127
128 (% class="table-bordered" %)
129 |=(% scope="row" style="text-align: center; vertical-align: middle;" %)**Rigidity grade**|=(% style="text-align: center; vertical-align: middle;" %)**Load mechanism type**
130 |=(% style="text-align: center; vertical-align: middle;" %)Grade 4 to 8|(% style="text-align:center; vertical-align:middle" %)Some large machinery
131 |=(% style="text-align: center; vertical-align: middle;" %)Grade 8 to 15|(% style="text-align:center; vertical-align:middle" %)Low rigidity applications such as belts
132 |=(% style="text-align: center; vertical-align: middle;" %)Grade 15 to 20|(% style="text-align:center; vertical-align:middle" %)High rigidity applications such as ball screw and direct connection
133
134 Table 7-3 Experience reference of rigidity grade
135
136 When the function code P03-03 is set to 0, the gain parameters are stored in the first gain by modifying the rigidity grade.
137
138 When debugging with the host computer debugging software, automatic rigidity level measurement can be carried out, which is used to select a set of appropriate rigidity grades as operating parameters. The operation steps are as follows:
139
140 * Step1 Confirm that the servo is in the ready state, the panel displays “rdy”, and the communication line is connected;
141 * Step2 Open the host computer debugging software, enter the trial run interface, set the corresponding parameters, and click "Servo on";
142 * Step3 Click the "forward rotation" or "reverse rotation" button to confirm the travel range of the servo operation;
143 * Step4 After the "start recognition" of inertia recognition lights up, click "start recognition" to perform inertia recognition, and the load inertia can be measured.
144 * Step5 After the inertia recognition test is completed, click "Save Inertia Value";
145 * Step6 Click "Next" at the bottom right to go to the parameter adjustment interface, and click "Parameter measurement" to start parameter measurement.
146 * Step7 After the parameter measurement is completed, Wecon SCTool will pop up a confirmation window for parameter writing and saving.
147
148 (% class="table-bordered" %)
149 (% class="warning" %)|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611152634-2.png]]
150 |(((
151 ✎There may be a short mechanical whistling sound during the test. Generally, the servo will automatically stop the test. If it does not stop automatically or in other abnormal situations, you can click the "Servo Off" button on the interface to turn off the servo, or power off the machine!
152
153 ✎For the detailed operation of the host computer debugging software, please refer to "Wecon Servo Debugging Platform User Manual".
154 )))
155
156 (% class="table-bordered" %)
157 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 84px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 138px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 103px;" %)(((
158 **Setting method**
159 )))|=(% style="text-align: center; vertical-align: middle; width: 105px;" %)(((
160 **Effective time**
161 )))|=(% style="text-align: center; vertical-align: middle; width: 87px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 83px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 431px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
162 |=(% style="text-align: center; vertical-align: middle; width: 84px;" %)P03-03|(% style="text-align:center; vertical-align:middle; width:138px" %)Self-adjusting mode selection|(% style="text-align:center; vertical-align:middle; width:103px" %)(((
163 Operation setting
164 )))|(% style="text-align:center; vertical-align:middle; width:105px" %)(((
165 Effective immediately
166 )))|(% style="text-align:center; vertical-align:middle; width:87px" %)0|(% style="text-align:center; vertical-align:middle; width:83px" %)0 to 2|(% style="width:431px" %)(((
167 * 0: Rigidity grade self-adjusting mode. Position loop gain, speed loop gain, speed loop integral time constant, torque filter parameter settings are automatically adjusted according to the rigidity grade setting.
168 * 1: Manual setting; you need to manually set the position loop gain, speed loop gain, speed loop integral time constant, torque filter parameter setting
169 * 2: Online automatic parameter self-adjusting mode (Not implemented yet)
170 )))|(% style="text-align:center; vertical-align:middle" %)-
171
172 Table 7-4 Details of self-adjusting mode selection parameters
173
174 == Manual gain adjustment ==
175
176 When the servo automatic gain adjustment fails to achieve the desired result, you can manually fine-tune the gain to achieve better results.
177
178 The servo system consists of three control loops, from the outside to the inside are the position loop, the speed loop and the current loop. The basic control block diagram is shown as below.
179
180 (% style="text-align:center" %)
181 (((
182 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
183 [[**Figure 7-2 Basic block diagram of servo loop gain**>>image:image-20220608174209-2.png||id="Iimage-20220608174209-2.png"]]
184 )))
185
186 The more the inner loop is, the higher the responsiveness is required. Failure to comply with this principle may lead to system instability!
187
188 The default current loop gain of the servo drive has ensured sufficient responsiveness. Generally, no adjustment is required. Only the position loop gain, speed loop gain and other auxiliary gains need to be adjusted.
189
190 This servo drive has two sets of gain parameters for position loop and speed loop. The user can switch the two sets of gain parameters according to the setting value of P02-07 the 2nd gain switching mode. The parameters are below.
191
192 (% class="table-bordered" %)
193 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 450px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 751px;" %)**Name**
194 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P02-01|(% style="width:751px" %)The 1st position loop gain
195 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P02-02|(% style="width:751px" %)The 1st speed loop gain
196 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P02-03|(% style="width:751px" %)The 1st speed loop integral time constant
197 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P02-04|(% style="width:751px" %)The 2nd position loop gain
198 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P02-05|(% style="width:751px" %)The 2nd speed loop gain
199 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P02-06|(% style="width:751px" %)The 2nd speed loop integral time constant
200 |=(% style="text-align: center; vertical-align: middle; width: 450px;" %)P04-04|(% style="width:751px" %)Torque filter time constant
201
202 **Speed loop gain**
203
204 In the case of no vibration or noise in the mechanical system, the larger the speed loop gain setting value, the better the response of servo system and the better the speed followability. When noise occurs in the system, reduce the speed loop gain. The related function codes are shown as below.
205
206 (% class="table-bordered" %)
207 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 120px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 163px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 122px;" %)(((
208 **Setting method**
209 )))|=(% style="text-align: center; vertical-align: middle; width: 128px;" %)(((
210 **Effective time**
211 )))|=(% style="text-align: center; vertical-align: middle; width: 103px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 107px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 321px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
212 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P02-02|(% style="text-align:center; vertical-align:middle; width:163px" %)1st speed loop gain|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
213 Operation setting
214 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
215 Effective immediately
216 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)65|(% style="text-align:center; vertical-align:middle; width:107px" %)0 to 35000|(% style="width:321px" %)Set speed loop proportional gain to determine the responsiveness of speed loop.|(% style="text-align:center; vertical-align:middle" %)0.1Hz
217 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P02-05|(% style="text-align:center; vertical-align:middle; width:163px" %)2nd speed loop gain|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
218 Operation setting
219 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
220 Effective immediately
221 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)65|(% style="text-align:center; vertical-align:middle; width:107px" %)0 to 35000|(% style="width:321px" %)Set speed loop proportional gain to determine the responsiveness of speed loop.|(% style="text-align:center; vertical-align:middle" %)0.1Hz
222
223 Table 7-5 Speed loop gain parameters
224
225 (% style="text-align:center" %)
226 (((
227 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
228 [[**Figure 7-3 Speed loop gain effect illustration**>>image:image-20220706152743-1.jpeg||id="Iimage-20220706152743-1.jpeg"]]
229 )))
230
231 **Speed loop integral time constant**
232
233 The speed loop integral time constant is used to eliminate the speed loop deviation. Decreasing the integral time constant of the speed loop can increase the speed of the speed following. If the set value is too small, is will easily cause speed overshoot or vibration. When the time constant is set too large, the integral action will be weakened, resulting in a deviation of the speed loop. Related function codes are shown as below.
234
235 (% class="table-bordered" %)
236 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 98px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 173px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 122px;" %)(((
237 **Setting method**
238 )))|=(% style="text-align: center; vertical-align: middle; width: 112px;" %)(((
239 **Effective time**
240 )))|=(% style="text-align: center; vertical-align: middle; width: 109px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 114px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 278px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle; width: 78px;" %)**Unit**
241 |=(% style="text-align: center; vertical-align: middle; width: 98px;" %)P02-03|(% style="text-align:center; vertical-align:middle; width:173px" %)(((
242 1st speed loop integral time constant
243 )))|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
244 Operation setting
245 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
246 Effective immediately
247 )))|(% style="text-align:center; vertical-align:middle; width:109px" %)1000|(% style="text-align:center; vertical-align:middle; width:114px" %)100 to 65535|(% style="width:278px" %)Set the speed loop integral constant. The smaller the set value, the stronger the integral effect.|(% style="text-align:center; vertical-align:middle; width:78px" %)(((
248 0.1ms
249 )))
250 |=(% style="text-align: center; vertical-align: middle; width: 98px;" %)P02-06|(% style="text-align:center; vertical-align:middle; width:173px" %)(((
251 2nd speed loop integral time constant
252 )))|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
253 Operation setting
254 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
255 Effective immediately
256 )))|(% style="text-align:center; vertical-align:middle; width:109px" %)1000|(% style="text-align:center; vertical-align:middle; width:114px" %)0 to 65535|(% style="width:278px" %)Set the speed loop integral constant. The smaller the set value, the stronger the integral effect.|(% style="text-align:center; vertical-align:middle; width:78px" %)(((
257 0.1ms
258 )))
259
260 Table 7-6 Speed loop integral time constant parameters
261
262 (% style="text-align:center" %)
263 (((
264 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
265 [[**Figure 7-4 Speed loop integral time constant effect illustration**>>image:image-20220706153140-2.jpeg||id="Iimage-20220706153140-2.jpeg"]]
266 )))
267
268 **Position loop gain**
269
270 Determine the highest frequency of the position instruction that the position loop can follow the change. Increasing this parameter can speed up the positioning time and improve the ability of the motor to resist external disturbances when the motor is stationary. However, if the setting value is too large, the system may be unstable and oscillate. The related function codes are shown as below.
271
272 (% class="table-bordered" %)
273 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 95px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 174px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)(((
274 **Setting method**
275 )))|=(% style="text-align: center; vertical-align: middle; width: 114px;" %)(((
276 **Effective time**
277 )))|=(% style="text-align: center; vertical-align: middle; width: 79px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 91px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 355px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
278 |=(% style="text-align: center; vertical-align: middle; width: 95px;" %)P02-01|(% style="text-align:center; vertical-align:middle; width:174px" %)1st position loop gain|(% style="text-align:center; vertical-align:middle; width:120px" %)(((
279 Operation setting
280 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)(((
281 Effective immediately
282 )))|(% style="text-align:center; vertical-align:middle; width:79px" %)400|(% style="text-align:center; vertical-align:middle; width:91px" %)0 to 6200|(% style="width:355px" %)Set position loop proportional gain to determine the responsiveness of position control system.|(% style="text-align:center; vertical-align:middle" %)0.1Hz
283 |=(% style="text-align: center; vertical-align: middle; width: 95px;" %)P02-04|(% style="text-align:center; vertical-align:middle; width:174px" %)2nd position loop gain|(% style="text-align:center; vertical-align:middle; width:120px" %)(((
284 Operation setting
285 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)(((
286 Effective immediately
287 )))|(% style="text-align:center; vertical-align:middle; width:79px" %)35|(% style="text-align:center; vertical-align:middle; width:91px" %)0 to 6200|(% style="width:355px" %)Set position loop proportional gain to determine the responsiveness of position control system.|(% style="text-align:center; vertical-align:middle" %)0.1Hz
288
289 Table 7-7 Position loop gain parameters
290
291 (% style="text-align:center" %)
292 (((
293 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
294 [[**Figure 7-5 Position loop gain effect illustration**>>image:image-20220706153656-3.jpeg||id="Iimage-20220706153656-3.jpeg"]]
295 )))
296
297 **Torque instruction filter time**
298
299 Selecting an appropriate torque filter time constant could suppress mechanical resonance. The larger the value of this parameter, the stronger the suppression ability. If the setting value is too large, it will decrease the current loop response frequency and cause needle movement. The related function codes are shown as below.
300
301 (% class="table-bordered" %)
302 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 117px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 200px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)(((
303 **Setting method**
304 )))|=(% style="text-align: center; vertical-align: middle; width: 127px;" %)(((
305 **Effective time**
306 )))|=(% style="text-align: center; vertical-align: middle; width: 79px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 371px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
307 |=(% style="text-align: center; vertical-align: middle; width: 117px;" %)P04-04|(% style="text-align:center; vertical-align:middle; width:200px" %)Torque filter time constant|(% style="text-align:center; vertical-align:middle; width:120px" %)(((
308 Operation setting
309 )))|(% style="text-align:center; vertical-align:middle; width:127px" %)(((
310 Effective immediately
311 )))|(% style="text-align:center; vertical-align:middle; width:79px" %)50|(% style="width:371px" %)This parameter is automatically set when “self-adjustment mode selection” is selected as 1 or 2|(% style="text-align:center; vertical-align:middle" %)0.01ms
312
313 Table 7-8 Details of torque filter time constant parameters
314
315 == **Feedforward gain** ==
316
317 Speed feedforward could be used in position control mode and full closed-loop function. It could improve the response to the speed instruction and reduce the position deviation with fixed speed.
318
319 Speed feedforward parameters are shown in __Table 7-9__. Torque feedforward parameters are shown in __Table 7-10__.
320
321 Torque feedforward could improve the response to the torque instruction and reduce the position deviation with fixed acceleration and deceleration.
322
323 (% class="table-bordered" %)
324 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 125px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 330px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 746px;" %)**Adjustment description**
325 |=(% style="text-align: center; vertical-align: middle; width: 125px;" %)P02-09|(% style="text-align:center; vertical-align:middle; width:330px" %)Speed feedforward gain|(% rowspan="2" style="width:746px" %)(((
326 When the speed feedforward filter is set to 50 (0.5 ms), gradually increase the speed feedforward gain, and the speed feedforward will take effect. The position deviation during operation at a certain speed will be reduced according to the value of speed feedforward gain as the formula below.
327
328 Position deviation (instruction unit) = instruction speed[instruction unit/s]÷position loop gain [1/s]×(100－speed feedforward gain [%])÷100
329 )))
330 |=(% style="text-align: center; vertical-align: middle; width: 125px;" %)P02-10|(% style="text-align:center; vertical-align:middle; width:330px" %)Speed feedforward filtering time constant
331
332 Table 7-9 Speed feedforward parameters
333
334 (% style="text-align:center" %)
335 (((
336 (% class="wikigeneratedid img-thumbnail" style="display:inline-block;" %)
337 [[**Figure 7-6 Speed feedforward parameters effect illustration**>>image:image-20220706155307-4.jpeg||height="119" id="Iimage-20220706155307-4.jpeg" width="835"]]
338 )))
339
340
341 (% class="table-bordered" %)
342 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 125px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 259px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 690px;" %)**Adjustment description**
343 |=(% style="text-align: center; vertical-align: middle; width: 125px;" %)P02-11|(% style="text-align:center; vertical-align:middle; width:259px" %)Torque feedforward gain|(% rowspan="2" style="width:690px" %)Increase the torque feedforward gain because the position deviation can be close to 0 during certain acceleration and deceleration. Under the ideal condition of external disturbance torque not operating, when driving in the trapezoidal speed model, the position deviation can be close to 0 in the entire action interval. In fact, there must be external disturbance torque, so the position deviation cannot be zero. In addition, like the speed feedforward, although the larger the constant of the torque feedforward filter, the smaller the action sound, but the greater the position deviation of the acceleration change point.
344 |=(% style="text-align: center; vertical-align: middle; width: 125px;" %)P02-12|(% style="text-align:center; vertical-align:middle; width:259px" %)Torque feedforward filtering time constant
345
346 Table 7-10 Torque feedforward parameters
347
348 == **Model Tracking Control Function** ==
349
350 Model tracking control is suitable for position control mode, which adds a model loop outside the three loops. In the model loop, new position commands, speed feedforward and torque feedforward and other control quantities are generated according to the user's response requirements to the system and the ideal motor control model. Applying these control quantities to the actual control loop can significantly improve the response performance and positioning performance of the position control, the design block diagram is as follows:
351
352 (% style="text-align:center" %)
353 (((
354 (% class="wikigeneratedid img-thumbnail" style="display:inline-block;" %)
355 [[**Figure 7-7 Block Diagram of Model Tracking Control Design**>>image:20230515-7.png||height="394" id="20230515-7.png" width="931"]]
356 )))
357
358 The usage method and conditions of model tracking control:
359
360 ~1. Correctly set the inertia ratio of the system P3-1, which can be obtained by monitoring the real-time load inertia ratio of U0-20.
361
362 2. Set the load rigidity level P3-2, set an appropriate value, it does not need to set a high rigidity level (recommended value 17~~21 under rigid load).
363
364 3. Set P2-20=1 to enable the function of model tracking control.
365
366 4. Adjust the P2-21 model tracking control gain from small to large, and gradually increase in steps of 1000 until the responsiveness of the system meets the actual demand. The responsiveness of the system is mainly determined by this parameter.
367
368 5. After the responsiveness meets the requirements, user can adjust the parameters appropriately to increase the load rigidity level P3-2.
369
370 (% class="box infomessage" %)
371 (((
372 **✎Note**: Model tracking control is only available in position mode, and cannot be used in other modes.
373 )))
374
375 (% class="table-bordered" %)
376 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 120px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 163px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 122px;" %)(((
377 **Setting method**
378 )))|=(% style="text-align: center; vertical-align: middle; width: 128px;" %)(((
379 **Effective time**
380 )))|=(% style="text-align: center; vertical-align: middle; width: 103px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 107px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 321px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
381 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P2-20|(% style="text-align:center; vertical-align:middle; width:163px" %)(((
382 Enable model(% style="background-color:transparent" %) tracking control function
383 )))|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
384 Shutdown setting
385 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
386 Effective immediately
387 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)0|(% style="text-align:center; vertical-align:middle; width:107px" %)0 to 1|When the function code is set to 1, enable the model tracking control function.|
388 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P2-21|(% style="text-align:center; vertical-align:middle; width:163px" %)Model tracking control gain|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
389 Shutdown setting
390 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
391 Effective immediately
392 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)1000|(% style="text-align:center; vertical-align:middle; width:107px" %)200 to 20000|(% rowspan="2" style="width:321px" %)Increasing the model tracking control gain can improve the position response performance of the model loop. If the gain is too high, it may cause overshoot behavior. The gain compensation affects the damping ratio of the model loop, and the damping ratio becomes larger as the gain compensation becomes larger.|(% style="text-align:center; vertical-align:middle" %)0.1/s
393 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P2-22|(% style="text-align:center; vertical-align:middle; width:163px" %)Model tracking control gain compensation|(% style="text-align:center; vertical-align:middle; width:122px" %)(((
394 Shutdown setting
395 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
396 Effective immediately
397 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)1000|(% style="text-align:center; vertical-align:middle; width:107px" %)500 to 2000|(% style="text-align:center; vertical-align:middle" %)0.10%
398
399 (% class="table-bordered" %)
400 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 120px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 163px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 122px;" %)(((
401 **Setting method**
402 )))|=(% style="text-align: center; vertical-align: middle; width: 128px;" %)(((
403 **Effective time**
404 )))|=(% style="text-align: center; vertical-align: middle; width: 103px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 107px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 321px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle;" %)**Unit**
405 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P2-23|(% style="text-align:center; vertical-align:middle; width:163px" %)Model tracking control forward rotation bias|(((
406 Operation setting
407 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
408 Effective immediately
409 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)1000|(% style="text-align:center; vertical-align:middle; width:107px" %)0 to 10000|(% rowspan="2" %)(% style="width:321px" %)Torque feedforward size in the positive and reverse direction under model tracking control|(% style="text-align:center; vertical-align:middle" %)0.10%
410 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P2-24|(% style="text-align:center; vertical-align:middle; width:163px" %)Model tracking control reverses rotation bias|(((
411 Operation setting
412 )))|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
413 Effective immediately
414 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)1000|(% style="text-align:center; vertical-align:middle; width:107px" %)0 to 10000|(% style="text-align:center; vertical-align:middle" %)0.10%
415 |=(% style="text-align: center; vertical-align: middle; width: 120px;" %)P2-25|(% style="text-align:center; vertical-align:middle; width:163px" %)Model tracking control speed feedforward compensation|Operation setting|(% style="text-align:center; vertical-align:middle; width:128px" %)(((
416 Effective immediately
417 )))|(% style="text-align:center; vertical-align:middle; width:103px" %)1000|(% style="text-align:center; vertical-align:middle; width:107px" %)0 to 10000|(% style="width:321px" %)The size of the speed feedforward under model tracking control|(% style="text-align:center; vertical-align:middle" %)0.10%
418
419 Please refer to the following for an example of the procedure of adjusting servo gain.
420
421 (% style="width:1508px" %)
422 |=(% style="text-align:center; vertical-align:middle; width:80px" %)**Step**|=(% style="text-align:center; vertical-align:middle; width:1420px" %)**Content**
423 |=(% style="text-align: center; vertical-align: middle; width: 80px;" %)1|Please try to set the correct load inertia ratio parameter P3-1.
424 |=(% style="text-align:center; vertical-align:middle; width:80px" %)2|If the automatic adjustment mode is used (P3-3 is set to 0), please set the basic rigidity level parameter P3-2. If in manual adjustment mode (P3-3 is set to 1), please set the gain P2-1~~P2-3 related to the position loop and speed loop and the torque filter time constant P4-4. The setting principle is mainly no vibration and overshoot.
425 |=(% style="text-align: center; vertical-align: middle; width: 80px;" %)3|Turn on the model tracking function, set P2-20 to 1.
426 |=(% style="text-align: center; vertical-align: middle; width: 80px;" %)4|Increase the model tracking gain P2-21 within the range of no overshoot and vibration occurring.
427 |=(% style="text-align: center; vertical-align: middle; width: 80px;" %)5|If the rigidity level of step 2 is set relatively low, user can properly increase the rigidity level P3-2.
428 |=(% style="text-align: center; vertical-align: middle; width: 80px;" %)6|When overshoot occurs, or the responses of forward rotation and reverse rotation are different, user can fine-tune through model tracking control forward bias P2-23, model tracking control reverse bias P2-24, model tracking control speed feedforward compensation P2 -25.
429
430 == **Gain switching** ==
431
432 **Gain switching function:**
433
434 ● Switch to a lower gain in the motor stationary (servo enabled)state to suppress vibration;
435
436 ● Switch to a higher gain in the motor stationary state to shorten the positioning time;
437
438 ● Switch to a higher gain in the motor running state to get better command tracking performance;
439
440 ● Switch different gain settings by external signals depending on the load connected.
441
442 **Gain switching parameter setting**
443
444 ①When P02-07=0
445
446 Fixed use of the first gain (using P02-01~~P02-03), and the switching of P/PI (proportional/proportional integral) control could be realized through DI function 10 (GAIN-SEL, gain switching).
447
448 (% style="text-align:center" %)
449 (((
450 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
451 [[image:20230515-8.png||height="378" id="20230515-8.png" width="363"]]
452 )))
453
454 ② When P02-07=1
455
456 The switching conditions can be set through parameter P02-08 to realize switching between the first gain (P02-01~~P02-03) and the second gain (P02-04~~P02-06).
457
458 (% style="text-align:center" %)
459 (((
460 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
461 [[**Figure 7-9 Flow chart of gain switching when P02-07=1**>>image:20230515-9.png||id="20230515-9.png"]]
462 )))
463
464 |=(% style="text-align:center; vertical-align:middle; width:120px" %)**P02-08**|=(% style="text-align: center; vertical-align: middle; width: 464px;" %)**Content**|=(% style="text-align: center; vertical-align: middle; width: 946px;" %)**Diagram**
465 |=(% style="text-align:center; vertical-align:middle" %)0|(% style="text-align:center; vertical-align:middle; width:464px" %)Fixed use of the first gain|(% style="width:946px" %)~-~-
466 |=(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle; width:464px" %)Switching with DI|(% style="width:946px" %)~-~-
467 |=(% style="text-align:center; vertical-align:middle" %)(((
468 2
469 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
470 Large torque command
471 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-1.png||height="310" width="543"]]
472 |=(% style="text-align:center; vertical-align:middle" %)(((
473 3
474 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
475 Large actual torque
476 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-2.png||height="252" width="550"]]
477 |=(% style="text-align:center; vertical-align:middle" %)(((
478 4
479 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
480 Large speed command
481 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-3.png||height="212" width="558"]]
482 |=(% style="text-align:center; vertical-align:middle" %)(((
483 5
484 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
485 Fast actual speed
486 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-4.png||height="223" width="561"]]
487 |=(% style="text-align:center; vertical-align:middle" %)(((
488 6
489 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
490 Speed command change rate is large
491 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-5.png||height="327" width="570"]]
492 |=(% style="text-align:center; vertical-align:middle;width:74px" %)(((
493 7
494 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
495 Large position deviation
496 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-6.png||height="305" width="574"]]
497 |=(% style="text-align:center; vertical-align:middle;" %)(((
498 8
499 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
500 Position command
501 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-7.png||height="280" width="570"]]
502 |=(% style="text-align:center; vertical-align:middle; width:74px" %)(((
503 9
504 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
505 Positioning completed
506 )))|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230515140641-8.png||height="302" width="553"]]
507 |=(% style="text-align:center; vertical-align:middle" %)(((
508 10
509 )))|(% style="text-align:center; vertical-align:middle; width:464px" %)(((
510 Position command + actual speed
511 )))|(% style="text-align:center; vertical-align:middle; width:946px" %)(((
512 Refer to the chart below
513 )))
514
515 (% style="text-align:center" %)
516 (((
517 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
518 [[**Figure 7-10 P02-08=10 Position command + actual speed gain description**>>image:20230515-10.png||id="Iimage-20220608174118-1.png"]]
519 )))
520
521 **Description of related parameters**
522
523 |=(% rowspan="2" style="text-align: center; vertical-align: middle; width:120px" %)
524 **P02-07**|=(% style="width:150px" %)**Parameter name**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Setting method**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Effective time**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Default**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Set range**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Application category**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Unit**
525 |(% style="text-align:center; width:150px" %)The second gain switching mode|(% style="text-align:center" %)Operation setting|(% style="text-align:center" %)Effective immediately|(% style="text-align:center" %)0|(% style="text-align:center" %)0 to 1|(% style="text-align:center" %)Gain control|
526 |(% colspan="8" %)(((
527 Set the switching mode of the second gain.
528
529 |=(% style="text-align: center; vertical-align: middle; width:120px" %)**Setting value**|=(% style="text-align: center; vertical-align: middle" %)**Function**
530 |=(% style="text-align: center; vertical-align: middle" %)0|(((
531 The first gain is used by default. Switching using DI function 10 (GAIN-SEL, gain switching):
532
533 DI logic invalid: PI control;
534
535 DI logic valid: PI control.
536 )))
537 |=(% style="text-align: center; vertical-align: middle" %)1|The first gain and the second gain are switched by the setting value of P02-08.
538 )))
539
540 |=(% rowspan="2" style="text-align: center; vertical-align: middle; width:120px" %)**P02-08**|=(% style="width:150px" %)Parameter name|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Setting method**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Effective time**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Default**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Set range**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Application category**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Unit**
541 |(% style="text-align:center; width:150px" %)Gain switching condition selection|(% style="text-align:center" %)Operation setting|(% style="text-align:center" %)Effective immediately|(% style="text-align:center" %)0|(% style="text-align:center" %)0 to 10|(% style="text-align:center" %)Gain control|
542 |(% colspan="8" %)(((
543 Set the conditions for gain switching.
544
545 |=(% style="text-align: center; vertical-align: middle; width:120px" %)Setting value|=(% style="text-align: center; vertical-align: middle" %)Gain switching conditions|=(% style="text-align: center; vertical-align: middle" %)Details
546 |=(% style="text-align: center; vertical-align: middle" %)0|(% style="text-align:center; vertical-align:middle" %)The default is the first gain|Fixed use of the first gain
547 |=(% style="text-align: center; vertical-align: middle" %)1|(% style="text-align:center; vertical-align:middle" %)Switch by DI port|(((
548 Use DI function 10 (GAIN-SEL, gain switching);
549
550 DI logic is invalid: the first gain (P02-01~~P02-03);
551
552 DI logic is valid: the second gain (P02-04~~P02-06).
553 )))
554 |=(% style="text-align: center; vertical-align: middle" %)2|(% style="text-align:center; vertical-align:middle" %)Large torque command|(((
555 In the previous first gain, when the absolute value of torque command is greater than (grade + hysteresis), the second gain is switched;
556
557 In the previous second gain, when the absolute value of torque command is less than the value of (grade - hysteresis) and the duration is greater than [P02-13], the first gain is returned.
558 )))
559 |=(% style="text-align: center; vertical-align: middle" %)3|(% style="text-align:center; vertical-align:middle" %)Large actual torque|(((
560 In the previous first gain, when the absolute value of actual torque is greater than ( grade + hysteresis ), the second gain is switched;
561
562 In the previous second gain, when the absolute value of actual torque is less than the value of (grade - hysteresis) and the duration is greater than [P02-13], the first gain is returned.
563 )))
564 |=(% style="text-align: center; vertical-align: middle" %)4|(% style="text-align:center; vertical-align:middle" %)Large speed command|(((
565 In the previous first gain, when the absolute value of speed command is greater than (grade + hysteresis), the second gain is switched;
566
567 In the previous second gain, when the absolute value of speed command is less than the value of (grade - hysteresis) and the duration is greater than [P02-13], the first gain is returned.
568 )))
569 |=(% style="text-align: center; vertical-align: middle" %)5|(% style="text-align:center; vertical-align:middle" %)Large actual speed|(((
570 In the previous first gain, when the absolute value of actual speed is greater than (grade + hysteresis), the second gain is switched;
571
572 In the previous second gain, when the absolute value of actual speed is less than the value of (grade - hysteresis) and the duration is greater than [P02-13], the first gain is returned.
573 )))
574 |=(% style="text-align: center; vertical-align: middle" %)6|(% style="text-align:center; vertical-align:middle" %)Large rate of change in speed command|(((
575 In the previous first gain, when the absolute value of the rate of change in speed command is greater than (grade + hysteresis), the second gain is switched;
576
577 In the previous second gain, switch to the first gain when the absolute value of the rate of change in speed command is less than the value of (grade - hysteresis) and the duration is greater than [P02-13], the first gain is returned.
578 )))
579 |=(% style="text-align: center; vertical-align: middle" %)7|(% style="text-align:center; vertical-align:middle" %)Large position deviation|(((
580 In the previous first gain, when the absolute value of position deviation is greater than (grade + hysteresis), the second gain is switched;
581
582 In the previous second gain, switch to the first gain when the absolute value of position deviation is less than the value of (grade - hysteresis) and the duration is greater than [P02-13], the first gain is returned.
583 )))
584 |=(% style="text-align: center; vertical-align: middle" %)8|(% style="text-align:center; vertical-align:middle" %)Position command|(((
585 In the previous first gain, if the position command is not 0, switch to the second gain;
586
587 In the previous second gain, if the position command is 0 and the duration is greater than [P02-13], the first gain is returned.
588 )))
589 |=(% style="text-align: center; vertical-align: middle" %)9|(% style="text-align:center; vertical-align:middle" %)Positioning complete|(((
590 In the previous first gain, if the positioning is not completed, the second gain is switched; In the previous second gain, if the positioning is not completed and the duration is greater than [P02-13], the first gain is returned.
591 )))
592 |=(% style="text-align: center; vertical-align: middle" %)10|(% style="text-align:center; vertical-align:middle" %)Position command + actual speed|(((
593 In the previous first gain, if the position command is not 0, the second gain is switched;
594
595 In the previous second gain, if the position command is 0, the duration is greater than [P02-13] and the absolute value of actual speed is less than ( grade - hysteresis).
596 )))
597 )))
598
599 |=(% rowspan="2" style="text-align:center; vertical-align:middle; width:120px" %)**P02-13**|=(% style="width:150px" %)Parameter name|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Setting method**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Effective time**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Default**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Set range**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Application category**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Unit**
600 |(% style="text-align:center; width:150px" %)Delay Time for Gain Switching|(% style="text-align:center" %)Operation setting|(% style="text-align:center" %)Effective immediately|(% style="text-align:center" %)20|(% style="text-align:center" %)0 to 10000|(% style="text-align:center" %)Gain control|(% style="text-align:center" %)0.1ms
601 |(% colspan="8" style="text-align:center; vertical-align:middle" %)(((
602 The duration of the switching condition required for the second gain to switch back to the first gain.
603
604 [[image:image-20230515140953-9.png]]
605
606 **✎**Note: This parameter is only valid when the second gain is switched back to the first gain.
607 )))
608
609 |=(% rowspan="2" style="text-align:center; vertical-align:middle; width:120px" %)**P02-14**|=(% style="width:150px" %)Parameter name|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Setting method**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Effective time**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Default**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Set range**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Application category**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Unit**
610 |(% style="text-align:center; width:150px" %)Gain switching grade|(% style="text-align:center" %)Operation setting|(% style="text-align:center" %)Effective immediately|(% style="text-align:center" %)50|(% style="text-align:center" %)0 to 20000|(% style="text-align:center" %)Gain control|(% style="text-align:center" %)According to the switching conditions
611 |(% colspan="8" style="text-align:center; vertical-align:middle" %)(((
612 Set the grade of the gain condition. The generation of the actual switching action is affected by the two conditions of grade and hysteresis.
613
614 [[image:image-20230515140953-10.png]]
615 )))
616
617 |=(% rowspan="2" style="text-align:center; vertical-align:middle; width:120px" %)**P02-15**|=(% style="width:150px" %)Parameter name|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Setting method**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Effective time**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Default**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Set range**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Application category**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Unit**
618 |(% style="text-align:center; width:150px" %)Gain switching hysteresis|(% style="text-align:center" %)Operation setting|(% style="text-align:center" %)Effective immediately|(% style="text-align:center" %)20|(% style="text-align:center" %)0 to 20000|(% style="text-align:center" %)Gain control|(% style="text-align:center" %)According to the switching conditions
619 |(% colspan="8" style="text-align:center; vertical-align:middle" %)(((
620 Set the hysteresis to meet the gain switching condition.
621
622 [[image:image-20230515140953-11.png]]
623 )))
624
625 |=(% rowspan="2" style="text-align:center; vertical-align:middle; width:120px" %)**P02-16**|=(% style="width:150px" %)Parameter name|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Setting method**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Effective time**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Default**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Set range**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Application category**|=(% style="text-align: center; vertical-align: middle; width: 120px;" %)**Unit**
626 |(% style="text-align:center; width:150px" %)Position loop gain switching time|(% style="text-align:center" %)Operation setting|(% style="text-align:center" %)Effective immediately|(% style="text-align:center" %)30|(% style="text-align:center" %)0 to 10000|(% style="text-align:center" %)Gain control|(% style="text-align:center" %)0.1ms
627 |(% colspan="8" style="text-align:center; vertical-align:middle" %)(((
628 Set the time for switching from the first position loop (P02-01) to the second position loop (P02-04) in the position control mode.
629
630 [[image:image-20230515140953-12.png]]|
631
632 If P02-04≤P02-01, then P02-16 is invalid, and the second gain is switched from the first gain immediately.
633 )))
634
635 = **Mechanical resonance suppression** =
636
637 == Mechanical resonance suppression methods ==
638
639 When the mechanical rigidity is low, vibration and noise may occur due to resonance caused by shaft twisting, and it may not be possible to increase the gain setting. In this case, by using a notch filter to reduce the gain at a specific frequency, after resonance is effectively suppressed, you can continue to increase the servo gain. There are 2 methods to suppress mechanical resonance.
640
641 **Torque instruction filter**
642
643 By setting the filter time constant, the torque instruction is attenuated in the high frequency range above the cutoff frequency, so as to achieve the expectation of suppressing mechanical resonance. The cut-off frequency of the torque instruction filter could be calculated by the following formula:
644
645 (% style="text-align:center" %)
646 [[image:image-20220706155820-5.jpeg||class="img-thumbnail"]]
647
648 **Notch filter**
649
650 The notch filter can achieve the expectation of suppressing mechanical resonance by reducing the gain at a specific frequency. When setting the notch filter correctly, the vibration can be effectively suppressed. You can try to increase the servo gain. The principle of the notch filter is shown in __Figure 7-3__.
651
652 == Notch filter ==
653
654 The VD2 series servo drives have 2 sets of notch filters, each of which has 3 parameters, namely notch frequency, width grade and depth grade.
655
656 **Width grade of notch filter**
657
658 The notch width grade is used to express the ratio of the notch width to the center frequency of the notch:
659
660 (% style="text-align:center" %)
661 [[image:image-20220706155836-6.png||class="img-thumbnail"]]
662
663 In formula (7-1), [[image:image-20220706155946-7.png]] is the center frequency of notch filter, that is, the mechanical resonance frequency; [[image:image-20220706155952-8.png]] is the width of notch filter, which represents the frequency bandwidth with an amplitude attenuation rate of **-3dB** relative to the center frequency of notch filter.
664
665 **Depth grade of notch filter**
666
667 The depth grade of notch filter represents the ratio relationship between input and output at center frequency.
668
669 When the notch filter depth grade is 0, the input is completely suppressed at center frequency. When the notch filter depth grade is 100, the input is completely passable at center frequency. Therefore, the smaller the the notch filter depth grade is set, the deeper the the notch filter depth, and the stronger the suppression of mechanical resonance. But the system may be unstable, you should pay attention to it when using it. The specific relationship is shown in __Figure 7-4__.
670
671 (% style="text-align:center" %)
672 (((
673 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
674 [[Figure 7-7 Notch characteristics, notch width, and notch depth>>image:image-20220608174259-3.png||id="Iimage-20220608174259-3.png"]]
675 )))
676
677
678 (% style="text-align:center" %)
679 (((
680 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
681 [[Figure 7-8 Frequency characteristics of notch filter>>image:image-20220706160046-9.png||id="Iimage-20220706160046-9.png"]]
682 )))
683
684
685 (% class="table-bordered" %)
686 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 113px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 155px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 115px;" %)(((
687 **Setting method**
688 )))|=(% style="text-align: center; vertical-align: middle; width: 121px;" %)(((
689 **Effective time**
690 )))|=(% style="text-align: center; vertical-align: middle; width: 99px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 102px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 362px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle; width: 96px;" %)**Unit**
691 |=(% style="text-align: center; vertical-align: middle; width: 113px;" %)P04-05|(% style="text-align:center; vertical-align:middle; width:155px" %)1st notch filter frequency|(% style="text-align:center; vertical-align:middle; width:115px" %)(((
692 Operation setting
693 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
694 Effective immediately
695 )))|(% style="text-align:center; vertical-align:middle; width:99px" %)300|(% style="text-align:center; vertical-align:middle; width:102px" %)250 to 5000|(% style="width:362px" %)Set the center frequency of the 1st notch filter. When the set value is 5000, the function of notch filter is invalid.|(% style="text-align:center; vertical-align:middle; width:96px" %)Hz
696 |=(% style="text-align: center; vertical-align: middle; width: 113px;" %)P04-06|(% style="text-align:center; vertical-align:middle; width:155px" %)1st notch filter depth|(% style="text-align:center; vertical-align:middle; width:115px" %)(((
697 Operation setting
698 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
699 Effective immediately
700 )))|(% style="text-align:center; vertical-align:middle; width:99px" %)100|(% style="text-align:center; vertical-align:middle; width:102px" %)0 to 100|(% style="width:362px" %)(((
701 1. 0: all truncated
702 1. 100: all passed
703 )))|(% style="text-align:center; vertical-align:middle; width:96px" %)-
704 |=(% style="text-align: center; vertical-align: middle; width: 113px;" %)P04-07|(% style="text-align:center; vertical-align:middle; width:155px" %)1st notch filter width|(% style="text-align:center; vertical-align:middle; width:115px" %)(((
705 Operation setting
706 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
707 Effective immediately
708 )))|(% style="text-align:center; vertical-align:middle; width:99px" %)4|(% style="text-align:center; vertical-align:middle; width:102px" %)0 to 12|(% style="width:362px" %)(((
709 1. 0: 0.5 times the bandwidth
710 1. 4: 1 times the bandwidth
711 1. 8: 2 times the bandwidth
712 1. 12: 4 times the bandwidth
713 )))|(% style="text-align:center; vertical-align:middle; width:96px" %)-
714 |=(% style="text-align: center; vertical-align: middle; width: 113px;" %)P04-08|(% style="text-align:center; vertical-align:middle; width:155px" %)2nd notch filter frequency|(% style="text-align:center; vertical-align:middle; width:115px" %)(((
715 Operation setting
716 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
717 Effective immediately
718 )))|(% style="text-align:center; vertical-align:middle; width:99px" %)500|(% style="text-align:center; vertical-align:middle; width:102px" %)250 to 5000|(% style="width:362px" %)Set the center frequency of the 2nd notch filter. When the set value is 5000, the function of the notch filter is invalid.|(% style="text-align:center; vertical-align:middle; width:96px" %)Hz
719 |=(% style="text-align: center; vertical-align: middle; width: 113px;" %)P04-09|(% style="text-align:center; vertical-align:middle; width:155px" %)2nd notch filter depth|(% style="text-align:center; vertical-align:middle; width:115px" %)(((
720 Operation setting
721 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
722 Effective immediately
723 )))|(% style="text-align:center; vertical-align:middle; width:99px" %)100|(% style="text-align:center; vertical-align:middle; width:102px" %)0 to 100|(% style="width:362px" %)(((
724 1. 0: all truncated
725 1. 100: all passed
726 )))|(% style="text-align:center; vertical-align:middle; width:96px" %)-
727 |=(% style="text-align: center; vertical-align: middle; width: 113px;" %)P04-10|(% style="text-align:center; vertical-align:middle; width:155px" %)2nd notch filter width|(% style="text-align:center; vertical-align:middle; width:115px" %)(((
728 Operation setting
729 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
730 Effective immediately
731 )))|(% style="text-align:center; vertical-align:middle; width:99px" %)4|(% style="text-align:center; vertical-align:middle; width:102px" %)0 to 12|(% style="width:362px" %)(((
732 1. 0: 0.5 times the bandwidth
733 1. 4: 1 times the bandwidth
734 1. 8: 2 times the bandwidth
735 1. 12: 4 times the bandwidth
736 )))|(% style="text-align:center; vertical-align:middle; width:96px" %)-
737
738 Table 7-11 Notch filter function code parameters
739
740 == Low frequency vibration suppression ==
741
742 Low-frequency vibration suppression is suitable for working conditions where the motor vibrates during deceleration and shutdown after the position command is sent, and the vibration amplitude gradually decreases. The use of the low-frequency vibration suppression function is effective in reducing the time to complete positioning due to vibration effects.
743
744 (% style="text-align:center" %)
745 (((
746 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
747 [[**Figure 7-13 Applicable working conditions for low-frequency vibration suppression**>>image:20230516-0713.png||id="20230516-0713.png"]]
748 )))
749
750 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 134px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 258px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 127px;" %)(((
751 **Setting method**
752 )))|=(% style="text-align: center; vertical-align: middle; width: 157px;" %)(((
753 **Effective time**
754 )))|=(% style="text-align: center; vertical-align: middle; width: 121px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 116px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 462px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle; width: 115px;" %)**Unit**
755 |=(% style="text-align: center; vertical-align: middle; width: 134px;" %)P4-11|(% style="text-align:center; vertical-align:middle; width:258px" %)Enable low-frequency vibration suppression function|(% style="text-align:center; vertical-align:middle; width:127px" %)(((
756 Operation setting
757 )))|(% style="text-align:center; vertical-align:middle; width:157px" %)(((
758 Effective immediately
759 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)0|(% style="text-align:center; vertical-align:middle; width:116px" %)0 to 1|(% style="width:462px" %)When the function code is set to 1, enable the low-frequency vibration suppression function.|(% style="width:115px" %)
760 |=(% style="text-align: center; vertical-align: middle; width: 134px;" %)P4-12|(% style="text-align:center; vertical-align:middle; width:258px" %)Low-frequency vibration suppression frequency|(% style="text-align:center; vertical-align:middle; width:127px" %)(((
761 Operation setting
762 )))|(% style="text-align:center; vertical-align:middle; width:157px" %)(((
763 Effective immediately
764 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)800|(% style="text-align:center; vertical-align:middle; width:116px" %)10 to 2000|(% style="width:462px" %)Set the vibration frequency when vibration occurs at the load end.|(% style="text-align:center; vertical-align:middle; width:115px" %)0.1HZ
765 |=(% style="text-align: center; vertical-align: middle; width: 134px;" %)P4-14|(% style="text-align:center; vertical-align:middle; width:258px" %)Shutdown vibration detection amplitude|(% style="text-align:center; vertical-align:middle; width:127px" %)(((
766 Operation setting
767 )))|(% style="text-align:center; vertical-align:middle; width:157px" %)(((
768 Effective immediately
769 )))|(% style="text-align:center; vertical-align:middle; width:121px" %)100|(% style="text-align:center; vertical-align:middle; width:116px" %)0 to 1000|(% style="width:462px" %)When the vibration amplitude is greater than (P5-12*P4-14 detection amplitude ratio), the low-frequency vibration frequency can be recognized and updated to the U0-16 monitor quantity.|(% style="text-align:center; vertical-align:middle; width:115px" %)0.001
770
771 **Vibration frequency detection:**
772
773 * Users can measure vibration by measuring equipment such as laser displacement．
774 * If no measuring equipment, the user can also read the position deviation waveform to confirm the vibration frequency through the "waveform" function of the PC debugging software.
775 * Low-frequency vibration detection needs to be coordinated by the two parameters of completion positioning threshold and vibration detection amplitude. When the vibration amplitude is greater than (P5-12*P4-14 detection amplitude ratio), the low-frequency vibration frequency can be recognized and updated to U0-16 monitoring quantity. For example, when the vibration amplitude is greater than (P5-12*P4-14*0.001) detection amplitude ratio. For example, in P05-12=800, P04_14=50, the vibration amplitude is greater than P5-12*P4-14*0.001=800*50*0.001=40 pulses, stop vibration frequency can be identified in U0-16.
776
777 **Debugging method:**
778
779 * Set the appropriate positioning completion thresholds P5-12 and P4-14 to help the software detect the vibration frequency.
780 * Run the position curve command to obtain the vibration frequency, and obtain the frequency through the speed curve of oscilloscope or U0-16.
781 * Set P4-12 vibration frequency and enable low frequency vibration suppression function P4-11.
782 * Run again to observe the speed waveform and determine whether to eliminate the vibration. If the vibration is not eliminated, please manually modify the vibration frequency and try again.
783
784 (% class="table-bordered" style="margin-right:auto" %)
785 (% class="warning" %)|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230516105941-2.png]]
786 |(% style="text-align:left; vertical-align:middle" %)Note: If there is a speed substantial vibration and the vibration increases during the debugging, it may be that the low-frequency vibration suppression is not suitable for the current working conditions, please immediately close the servo, or power down!
787
788 == Type A vibration suppression ==
789
790 Type A vibration suppression is suitable for durational vibration during motor operation or shutdown. Use Type A suppression to help reduce vibrations at specific frequencies that occur during motion (For the situation where the vibration continues to maintain and the vibration amplitude is almost constant after the command is completed.) As shown in Figure 7-14.
791
792 (% style="text-align:center" %)
793 (((
794 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
795 [[**Figure 7-14 Applicable situations for type A vibration suppression**>>image:20230516-0714.png]]
796 )))
797
798 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 136px;" %)**Function code**|=(% style="text-align: center; vertical-align: middle; width: 225px;" %)**Name**|=(% style="text-align: center; vertical-align: middle; width: 121px;" %)(((
799 **Setting method**
800 )))|=(% style="text-align: center; vertical-align: middle; width: 112px;" %)(((
801 **Effective time**
802 )))|=(% style="text-align: center; vertical-align: middle; width: 114px;" %)**Default value**|=(% style="text-align: center; vertical-align: middle; width: 183px;" %)**Range**|=(% style="text-align: center; vertical-align: middle; width: 501px;" %)**Definition**|=(% style="text-align: center; vertical-align: middle; width: 96px" %)**Unit**
803 |=(% style="text-align: center; vertical-align: middle; width: 136px;" %)P4-19|(% style="text-align:center; vertical-align:middle; width:225px" %)Enable the type A suppression function|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
804 Operation setting
805 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
806 Effective immediately
807 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)0|(% style="text-align:center; vertical-align:middle; width:183px" %)0 to 1|(% style="width:501px" %)When the function code is set to 1, enable the type A suppression function.|
808 |=(% style="text-align: center; vertical-align: middle; width: 136px;" %)P4-20|(% style="text-align:center; vertical-align:middle; width:225px" %)Type A suppression frequency|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
809 Operation setting
810 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
811 Effective immediately
812 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)1000|(% style="text-align:center; vertical-align:middle; width:183px" %)100 to 20000|(% style="width:501px" %)Set the frequency of Type A suppression.|(% style="text-align:center; vertical-align:middle" %)0.1HZ
813 |=(% style="text-align: center; vertical-align: middle; width: 136px;" %)P4-21|(% style="text-align:center; vertical-align:middle; width:225px" %)Type A suppression gain correction|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
814 Operation setting
815 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
816 Effective immediately
817 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)100|(% style="text-align:center; vertical-align:middle; width:183px" %)0 to 1000|(% style="width:501px" %)Correct the load inertia ratio size.|(% style="text-align:center; vertical-align:middle" %)0.01
818 |=(% style="text-align: center; vertical-align: middle; width: 136px;" %)P4-22|(% style="text-align:center; vertical-align:middle; width:225px" %)Type A suppression damping gain|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
819 Operation setting
820 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
821 Effective immediately
822 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)0|(% style="text-align:center; vertical-align:middle; width:183px" %)0 to 500|(% style="width:501px" %)The type A rejection compensation value is gradually increased until the vibration is reduced to the acceptable range.|(% style="text-align:center; vertical-align:middle" %)0.01
823 |=(% style="text-align: center; vertical-align: middle; width: 136px;" %)P4-23|(% style="text-align:center; vertical-align:middle; width:225px" %)Type A suppression phase correction|(% style="text-align:center; vertical-align:middle; width:121px" %)(((
824 Operation setting
825 )))|(% style="text-align:center; vertical-align:middle; width:112px" %)(((
826 Effective immediately
827 )))|(% style="text-align:center; vertical-align:middle; width:114px" %)200|(% style="text-align:center; vertical-align:middle; width:183px" %)0 to 900|(% style="width:501px" %)Type A suppression phase compensation.|(% style="text-align:center; vertical-align:middle" %)0.1 degree
828
829 **Vibration frequency detection:**
830
831 The vibration frequency can directly obtain the value of the current vibration frequency from the software oscilloscope vibration frequency, combined with real-time speed waveform to observe the current vibration situation.
832
833 **Debugging method:**
834
835 * Please set the correct inertia ratio parameter P3-1 when using type A vibration suppression,
836 * Run the position curve command, observe the servo host computer software waveform interface (sine wave) to obtain the vibration frequency.
837 * Set P4-20 vibration frequency and enable type A vibration suppression function P4-19. ( Type A vibration frequency takes effect when P4-19 is set to 1 for the first time. If change A-type vibration frequency P4-20, please set P4-19 to 0 again, then set to 1)
838 * Set P4-22 damping gain, gradually increasing from 0, each time increasing about 20.
839 * Observe the size of the vibration speed component, if the amplitude speed component is getting larger, it can be the vibration frequency setting error, if the vibration speed component is getting smaller, it means the vibration is gradually suppressed.
840 * When the vibration is suppressed, there is still a small part of the vibration speed component, users can fine-tune the P4-23 phase correction, the recommended value of 150~~300.
841
842 (% class="table-bordered" style="margin-right:auto" %)
843 (% class="warning" %)|(% style="text-align:center; vertical-align:middle" %)[[image:image-20230516135116-1.png]]
844 |(% style="text-align:left; vertical-align:middle" %)Note: If there is a speed substantial vibration and the vibration increases during the debugging, it may be that the low-frequency vibration suppression is not suitable for the current working conditions, please immediately close the servo, or power down!