08 Communication

1

The VD2 series servo drive has Modbus communication function, which could cooperate with the host computer for parameter modification, parameter query, monitoring volume servo status query and control. The servo drive is used as a slave device.

2

3

= **Modbus communication** =

4

5

== **Hardware wiring** ==

6

7

The position of RS485 communication port (take VD2B as an example) is as the figure below.

8

9

(% style="text-align:center" %)

10

[[image:image-20220608154248-1.png]]

11

12

Figure 8-1 The position of RS485 communication port of VD2B drive

13

14

For the position of the RS485 communication port of other models, see __[[4.5 Communication signal wiring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/#HCommunicationsignalwiring]]__.

15

16

The servo drive adopts RS485 half-duplex communication mode. The 485 bus should adopt the hand-in-hand structure instead of the star structure or the bifurcated structure. The star structure or bifurcation structure will produce reflected signals, which will affect the 485 communication.

17

18

(% class="table-bordered" %)

19

|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611153134-1.png]]

20

|(((

21

✎The wiring must use shielded twisted pair, stay away from strong electricity, do not run in parallel with the power line, let alone bundle it together!

22

23

✎In a half-duplex connection, only one servo drive can communicate with the host computer at the same time. If two or more servo drives upload data at the same time, bus competition will occur. Not only will it lead to communication failure, it may also cause some components to generate large currents and damage the components.

24

)))

25

26

(% style="text-align:center" %)

27

[[image:image-20220608174415-1.png]]

28

29

Figure 8-2 RS485 communication network wiring diagram

30

31

The terminal of RS485 network should use a terminating resistors of 120Ω to weaken the reflection of the signal. Intermediate networks cannot use terminating resistors.

32

33

No point in the RS485 network can be directly grounded. All devices in the network must be well grounded through their own grounding terminals.

34

35

(% class="table-bordered" %)

36

|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611153144-2.png]]

37

|Under no circumstances can the grounding wire form a closed loop.

38

39

When wiring, consider the drive capability of the computer/PLC and the distance between the computer/PLC and the servo drive. If the drive capacity is insufficient, a repeater is needed.

40

41

= **Modbus communication protocol analysis** =

42

43

== **Modbus data frame format** ==

44

45

The VD2 series servo drives currently support the RTU communication format. The typical data frame format is shown in the table.

46

47

(% class="table-bordered" %)

48

|(% rowspan="2" style="text-align:center; vertical-align:middle; width:425px" %)**There should be a message interval not less than 3.5 characters at the beginning**|(% style="text-align:center; vertical-align:middle; width:166px" %)**Address**|(% style="text-align:center; vertical-align:middle; width:189px" %)**Function code**|(% style="text-align:center; vertical-align:middle; width:155px" %)**Data**|(% style="text-align:center; vertical-align:middle; width:158px" %)**CRC check code**

49

|(% style="text-align:center; vertical-align:middle; width:166px" %)1 byte|(% style="text-align:center; vertical-align:middle; width:189px" %)1 byte|(% style="text-align:center; vertical-align:middle; width:155px" %)N bytes|(% style="text-align:center; vertical-align:middle; width:158px" %)2 bytes

50

51

== **Description of supported function codes** ==

52

53

The host reads and writes data to the servo through Modbus RTU format (03, 06 function codes). The corresponding Modbus function codes are as follows:

54

55

(% class="table-bordered" %)

56

|(% style="text-align:center; vertical-align:middle" %)**Operate**|(% style="text-align:center; vertical-align:middle" %)**Command code**

57

|(% style="text-align:center; vertical-align:middle" %)Read 16-bit/32-bit function code|(% style="text-align:center; vertical-align:middle" %)0x03

58

|(% style="text-align:center; vertical-align:middle" %)Write 16-bit function code|(% style="text-align:center; vertical-align:middle" %)0x06

59

|(% style="text-align:center; vertical-align:middle" %)Write 32-bit function code|(% style="text-align:center; vertical-align:middle" %)0x10

60

61

**Read function code: 0x03**

Request format:

|**high byte**|**low byte**|**high byte**|**low byte**

67

68

69

Correct response format:

70

71

72

|**high byte**|**low byte**

73

74

75

**Write function code: 0x06**

Request format:

|(% rowspan="2" %)**Address**|(% rowspan="2" %)**Function code**|(% colspan="2" %)(((

80

**Register address**

81

)))|(% colspan="2" %)**Data**|(% rowspan="2" %)**CRC check code**

82

|**high byte**|**low byte**|**high byte**|**low byte**

Response format:

|**high byte**|**low byte**|**high byte**|**low byte**

89

90

91

If the setting is successful, the original is returned

92

93

94

|1 byte|1 byte|N bytes|2 bytes

95

96

(% style="color:inherit; font-family:inherit; font-size:26px" %)**CRC check**

97

98

The servo uses a 16-bit CRC check, and the host computer must also use the same check rule, otherwise the CRC check will make mistake. When transmitting, the low bit is in the front and the high bit is at the back. The CRC code are as follows:

{

Uint16 crc = 0xffff;

Uint16 i;

while(uLen--)

{

crc ^=(Uint16) *pBuf++;

for(i=0; i<8; i++)

{

if(crc & 0x0001)

{

crc = (crc >> 1) ^ 0xa001;

}

else

{

crc = crc >> 1;

}

}

}

return crc;

}

return crc;

}

== **Error response frame** ==

151

152

(% class="table-bordered" %)

153

|(% style="text-align:center; vertical-align:middle" %)**Address**|(% style="text-align:center; vertical-align:middle" %)**Function code**|(% style="text-align:center; vertical-align:middle" %)**Error code**|(% style="text-align:center; vertical-align:middle" %)**CRC check code**

154

|(% style="text-align:center; vertical-align:middle" %)1 byte|(% style="text-align:center; vertical-align:middle" %)Command code+0x80|(% style="text-align:center; vertical-align:middle" %)Error code|(% style="text-align:center; vertical-align:middle" %)2 bytes

155

156

When an error occurs, set the function code bit7 issued by the host to 1, and return (for example, 0x03 returns 0x83, 0x06 returns 0x86); the description of the error code are as follows.

157

158

(% class="table-bordered" %)

159

|(% style="text-align:center; vertical-align:middle" %)**Error code**|(% style="text-align:center; vertical-align:middle" %)**Coding description**

160

|(% style="text-align:center; vertical-align:middle" %)0x0001|(% style="text-align:center; vertical-align:middle" %)Illegal command code

161

|(% style="text-align:center; vertical-align:middle" %)0x0002|(% style="text-align:center; vertical-align:middle" %)Illegal data address

162

|(% style="text-align:center; vertical-align:middle" %)0x0003|(% style="text-align:center; vertical-align:middle" %)Illegal data

163

|(% style="text-align:center; vertical-align:middle" %)0x0004|(% style="text-align:center; vertical-align:middle" %)Slave device failure

164

165

== **Communication example** ==

**03 Function code read**

170

171

Read the monitoring volume U0-31 bus voltage, the Modbus register address corresponding to this variable is 7716 (0x1E24)

Request format:

|**high byte**|**low byte**|**high byte**|**low byte**

177

|01|03|1E|24|00|01|C2 29

178

179

The slave responds normally:

180

181

182

|**high byte**|**low byte**

183

|01|03|02|0C|4F|FC B0

184

185

For example: The value read is 0x0C4F, which means that the voltage is 315.1V.

**06 Function Code Write**

190

191

P1-10 the maximum speed threshold is set to 3000rpm. This variable corresponds to the Modbus address: 266 (0x010A)

Request format:

|**high byte**|**low byte**|**high byte**|**low byte**

197

|01|06|01|0A|0B|B8|AF, 76

198

199

The slave responds normally:

200

201

202

|**high byte**|**low byte**|**high byte**|**low byte**

203

|01|06|01|0A|0B|B8|AF, 76

204

205

= **Servo communication parameter setting** =

206

207

(% style="text-align:center" %)

208

[[image:image-20220608174504-2.png]]

209

210

Figure 8-3 Modbus communication parameter setting process

211

212

**(1) Set the servo address P12-1**

213

214

When multiple servos are in network communication, each servo can only have a unique address, otherwise it will cause abnormal communication and fail to communicate.

215

216

**(2) Set the serial port baud rate P12-2**

217

218

The communication rate of the servo and the communication rate of the host computer must be set consistently, otherwise the communication cannot be carried out.

219

220

**(3) Set the serial port data format P12-3**

221

222

The data bit check methods of servo communication are:

Odd parity

Even parity

No parity

The stop bit: 1 stop bit and 2 stop bits.

231

232

The data frame format of the servo and the host computer must be consistent, otherwise the communication cannot be carried out.

233

234

**(4) Set that whether the function code changed by Modbus communication is written into EEPROM in real time [P12-4]**

235

236

When the host computer modifies the servo function code through communication, it can choose to store it in EEPROM in real time, which has the function of power-off storage.

237

238

If the value of the function code only needs to be rewritten once, and the value is used later, the function of real-time writing of the function code to EEPROM can be enabled.

239

240

If you need to change the value of the function code frequently, it is recommended to turn off the function of real-time writing to EERPOM of function code, otherwise the EEPROM will be shortened due to frequent erasing and writing of the EEPROM.

241

242

(% class="table-bordered" %)

243

|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611153214-3.png]]

244

|After the EEPROM is damaged, the servo will have an non resettable fault!

245

246

**(5) Set the high and low order of the 32-bit monitoring data**

247

248

Part of the monitoring volume is 32-bit length and occupies 2 consecutive bias numbers. The user needs to set the order of the data high bit and low bit correctly, otherwise it will cause data reading and writing errors!

249

250

For example, U0-54 (position within 1 circle of absolute encoder) occupies two consecutive offset numbers, which are 0x1E3D and 0x1E3E respectively. Assuming the value of U0-54 is 0x12345678, the correct data sequence bit should be 0x1E3D=0x5678 , 0x1E3E=0x1234 (little endian mode: low byte first, high byte behind.)

251

252

The description of related function codes are as follows.

253

254

(% class="table-bordered" %)

255

|(% style="text-align:center; vertical-align:middle; width:121px" %)**Function code**|(% style="text-align:center; vertical-align:middle; width:205px" %)**Name**|(% style="text-align:center; vertical-align:middle; width:187px" %)(((

256

**Setting method**

257

)))|(% style="text-align:center; vertical-align:middle; width:186px" %)(((

258

**Effective time**

259

)))|(% style="text-align:center; vertical-align:middle; width:130px" %)**Default value**|(% style="text-align:center; vertical-align:middle; width:132px" %)**Range**|(% style="text-align:center; vertical-align:middle; width:335px" %)**Definition**|(% style="text-align:center; vertical-align:middle; width:189px" %)**Unit**

260

|(% style="text-align:center; vertical-align:middle; width:121px" %)P12-02|(% style="text-align:center; vertical-align:middle; width:205px" %)Baud rate|(% style="text-align:center; vertical-align:middle; width:187px" %)(((

261

Operation setting

262

)))|(% style="text-align:center; vertical-align:middle; width:186px" %)(((

263

Effective immediately

264

)))|(% style="text-align:center; vertical-align:middle; width:130px" %)2|(% style="text-align:center; vertical-align:middle; width:132px" %)0 to 5|(% style="width:335px" %)(((

0-2400bps

1-4800bps

2-9600bps

3-19200bps

4-38400bps

5-57600bp

)))|(% style="text-align:center; vertical-align:middle; width:189px" %)-

277

|(% style="text-align:center; vertical-align:middle; width:121px" %)P12-03|(% style="text-align:center; vertical-align:middle; width:205px" %)Serial data format|(% style="text-align:center; vertical-align:middle; width:187px" %)(((

278

Operation setting

279

)))|(% style="text-align:center; vertical-align:middle; width:186px" %)(((

280

Effective immediately

281

)))|(% style="text-align:center; vertical-align:middle; width:130px" %)0|(% style="text-align:center; vertical-align:middle; width:132px" %)0 to 3|(% style="width:335px" %)(((

282

0: 1 stop bit, no parity

283

284

1: 1 stop bit, odd parity

285

286

2: 1 stop bit, even parity

287

288

3: 2 stop bits, no parity

289

)))|(% style="text-align:center; vertical-align:middle; width:189px" %)-

290

|(% style="text-align:center; vertical-align:middle; width:121px" %)P12-04|(% style="text-align:center; vertical-align:middle; width:205px" %)Modbus communication data is written into EEPROM|(% style="text-align:center; vertical-align:middle; width:187px" %)(((

291

Operation setting

292

)))|(% style="text-align:center; vertical-align:middle; width:186px" %)(((

293

Effective immediately

294

)))|(% style="text-align:center; vertical-align:middle; width:130px" %)0|(% style="text-align:center; vertical-align:middle; width:132px" %)0 to 1|(% style="width:335px" %)(((

295

0: Do not write to EEPROM, and do not store after power failure;

296

297

1: Write to EEPROM, power-down storage.

298

)))|(% style="text-align:center; vertical-align:middle; width:189px" %)-

299

300

= **Modbus communication variable address and value** =

301

302

== **Variable address description** ==

303

304

Modbus registers are divided into two categories:

305

306

~1. The first category is servo function code parameters (address: 0x0001 to 0x0D08), this part of the register is readable and writable (that is, 0x03 and 0x06 are supported);

307

308

2. The second category is the monitoring volume of the servo (address: 0x1E01 to 0x2010), this part of the register is only readable (0x03 function is supported).

309

310

**Servo function code representation: PXX-YY.**

311

312

XX: represents the function code group number,

313

314

YY: represents the bias within the function code group;;

315

316

During servo communication, the communication address of the function code is a 16-bit address, which is composed of the function code group number (high 8 bits) + group bias (low 8 bits), for example, the Modbus address corresponding to P12-1 (servo address) is 0x0C01.

317

318

**Servo monitor volume representation: Uxx-yy.**

319

320

xx: represents the monitoring volume group number,

321

322

yy: represents the bias within the monitoring volume group;

323

324

During Modbus communication, the starting address of the monitoring volume is 0x1E01, and the conversion relationship of the address is similar to the representation way of the function code.

325

326

For example, U0-01 (servo status) corresponds to the Modbus address is 0x1E01.

327

328

In order to facilitate actual use, this manual provides both decimal and hexadecimal address identification, it is shown in the following table:

329

330

(% class="table-bordered" %)

331

|(% style="text-align:center; vertical-align:middle" %)**Function code**|(% style="text-align:center; vertical-align:middle" %)(((

**Modbus address**

**(Hexadecimal)**

)))|(% style="text-align:center; vertical-align:middle" %)(((

**Modbus address**

**(Decimal)**

)))|(% style="text-align:center; vertical-align:middle" %)**Category**|(% style="text-align:center; vertical-align:middle" %)**Name**

340

|(% style="text-align:center; vertical-align:middle" %)P0-1|(% style="text-align:center; vertical-align:middle" %)0x0001|(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Basic settings|(% style="text-align:center; vertical-align:middle" %)Control mode

341

342

For detailed parameter addresses, please refer to __[["11.1 Lists of parameters".>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/11%20Appendix/#HListsofparameters]]__

343

344

== **Variable value type description** ==

345

346

When writing function codes with signed numbers, you need to convert the pre-written data into hexadecimal complements. The conversion rules are as follows:

347

348

~1. The data is positive or 0: complement code = original code

349

350

2. The data is negative: complement code = 0xFFFF-absolute value of data + 0x0001

351

352

For example,The 16-bit signed positive number +100, the original code is 0x0064, and the complement is: 0x0064. The 16-bit signed positive number -100, its hexadecimal complement is: 0xFFFF-0x0064 + 0x0001 = 0xFF9C.

353

354

If it is an unsigned number, just pass it directly according to its original code. For example, if the decimal number is 32768, write 0x8000 directly.

355

356

== **Numerical unit description** ==

357

358

Some values have units and decimals, such as 0.1%, 0.1Hz, 0.01ms, and the corresponding value conversion is required when reading and writing. The methods are as follows:

359

360

~1. When the unit is 0.1%: 1 represents 0.1%, 10 represents 1.0%, 1000 represents 100.0%. Therefore, writing 1000 means setting to 100.0%; on the contrary, if it is reading 1000, it means that the value is 100.0%;

361

362

2. When the unit is 0.01ms: 1 means 0.01ms, 50 means 0.5ms, 10000 means 100ms. Therefore, writing 1000 means setting to 10.00ms; on the contrary, if 1000 is read, it means 10.00ms; The other units can be deduced by this, and integer remains unchanged.

Wiki source code of 08 Communication

Navigation

Table of Contents