Changes for page 10 Malfunctions

Last modified by Theodore Xu on 2025/02/13 17:16

From 3.1 to 2.6 From 10.8 to 10.7

From version 10.7

edited by Stone Wu
on 2022/07/08 09:36

Change comment: There is no comment for this version

To version 3.1

edited by Leo Wei
on 2022/06/11 13:03

Change comment: Upload new image "ksjakfjk.png", version 1.1

Raw
Rendered

Summary

Page properties (3 modified, 0 added, 0 removed)

Details

Page properties

Parent

@@ -1,1 +1,1 @@
--Servo.1 User Manual.02 VD2 SA Series.WebHome
++Servo.2\. User Manual.06 VD2 SA Series Servo Drives Manual (Full V1\.1).WebHome

Author

@@ -1,1 +1,1 @@
--XWiki.Stone
++XWiki.admin

Content

@@ -19,21 +19,21 @@
  )))
  |(% style="vertical-align:middle; width:163px" %)Control the supply voltage failure|(% style="vertical-align:middle" %)Measures the AC voltage between L1C &L2C.
  |(% style="vertical-align:middle; width:163px" %)Servo drive fault|(% style="vertical-align:middle" %)Contact the agent or customer service
--|(% style="vertical-align:middle; width:213px" %)Panel display “Er.xx”|(% colspan="2" style="vertical-align:middle; width:1118px" %)Refer to [[10.2 Handling of faults and warnings during operation>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
++|(% style="vertical-align:middle; width:213px" %)Panel display “Er.xx”|(% colspan="2" style="vertical-align:middle; width:1118px" %)Refer to [[10.2 Handling of faults and warnings during operation>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
  |(% colspan="3" style="vertical-align:middle" %)After removing the fault, the servo drive panel should display "rdy"
  |(% rowspan="4" style="vertical-align:middle" %)Servo drive enable signal is valid(S-ON is ON)|(% rowspan="2" style="vertical-align:middle; width:213px" %)The axis of servo motor is in a free running state|(% style="vertical-align:middle; width:163px" %)Servo enable signal is invalid|(% style="vertical-align:middle" %)(((
--✎Check whether group P06 is set the servo enable signal (DI function 1: S-ON). If it is, check whether the corresponding DI terminal logic is valid. If it is invalid,please make it valid. Refer to __[[Group P06 DI/DO configuration>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/09%20Parameters/#HGroupP06DI2FDOconfiguration]]__
++✎Check whether group P06 is set the servo enable signal (DI function 1: S-ON). If it is, check whether the corresponding DI terminal logic is valid. If it is invalid,please make it valid. Refer to __[[Group P06 DI/DO configuration>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/11%20Appendix/#HGroupP06DIDOconfiguration]]__
--✎If group P06 parameters have set the servo enable signal, and the corresponding terminal logic is valid, but the panel still displays "rdy", check whether the DI terminal wiring is correct, please refer to__[[ 4 Wiring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/]]__
++✎If group P06 parameters have set the servo enable signal, and the corresponding terminal logic is valid, but the panel still displays "rdy", check whether the DI terminal wiring is correct, please refer to__[[ 4 Wiring>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/]]__
  )))
  |(% style="vertical-align:middle; width:163px" %)Control mode error|(% style="vertical-align:middle" %)Check whether the parameter P00-01 is set correctly
--|(% style="vertical-align:middle; width:213px" %)Panel display Er.xx|(% colspan="2" style="vertical-align:middle; width:1118px" %)Refer to [[10.2 Handling of faults and warnings during operation>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
++|(% style="vertical-align:middle; width:213px" %)Panel display Er.xx|(% colspan="2" style="vertical-align:middle; width:1118px" %)Refer to [[10.2 Handling of faults and warnings during operation>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
  |(% colspan="3" style="vertical-align:middle" %)After troubleshooting, the servo drive panel should display "run"
  |(% rowspan="2" style="vertical-align:middle" %)Input position instruction|(% style="vertical-align:middle; width:213px" %)The motor does not rotate|(% style="vertical-align:middle; width:163px" %)U0-09 (input instruction pulse number) always displays 0|(% style="vertical-align:middle" %)✎Not input position instruction(((
 . Confirm whether DI terminal uses forward drive prohibited (DI function 3: POT) or reverse drive prohibited (DI function 4: NOT).
 . Confirm whether DI terminal uses instruction pulse input prohibited (DI function 11: INH)
 . When P01-06=0(position instruction source), PLC or other pulse output device do not output pulse. Please use oscilloscope to check whether there is pulse input or check U0-08 (input instruction pulse frequency). Refer to __4 Wiring__
--1. When P01-06=1(position instruction source), please check whether the parameters of group P07 are set correctly. If yes, please confirm whether the DI function 20 (internal multi-segment position enable signal) and the corresponding DI terminal logic are set to be valid. Refer to __[[Group P07 multi-segment position>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/09%20Parameters/#HGroupP07multi-segmentposition]]__
++1. When P01-06=1(position instruction source), please check whether the parameters of group P07 are set correctly. If yes, please confirm whether the DI function 20 (internal multi-segment position enable signal) and the corresponding DI terminal logic are set to be valid. Refer to __[[Group P07 multi-segment position>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/11%20Appendix/#HGroupP07multi-segmentposition]]__
  )))
  |(% colspan="3" style="vertical-align:middle" %)After troubleshooting, the servo motor should be able to rotate normally
  |(% rowspan="3" style="vertical-align:middle" %)The motor does not rotate smoothly at low speed|(% style="vertical-align:middle; width:213px" %)Unstable low speed|(% style="vertical-align:middle; width:163px" %)Unreasonable gain setting|(% style="vertical-align:middle" %)Please adjust the gain.
@@ -66,20 +66,20 @@
  )))
  |Control the supply voltage failure|Measures the AC voltage between L1C &L2C.
  |Servo drive fault|Contact the agent or customer service
--|(% style="vertical-align:middle" %)Panel display “Er.xx”|(% colspan="2" %)Refer to [[10.2 Handling of faults and warnings during operation>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
++|(% style="vertical-align:middle" %)Panel display “Er.xx”|(% colspan="2" %)Refer to [[10.2 Handling of faults and warnings during operation>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
  |(% colspan="3" style="vertical-align:middle" %)After removing the fault, the servo drive panel should display "rdy"
  |(% rowspan="4" style="vertical-align:middle" %)Servo drive enable signal is valid(S-ON is ON)|(% rowspan="2" style="vertical-align:middle" %)The axis of servo motor is in a free running state|Servo enable signal is invalid|(((
--✎Check whether group P06 is set the servo enable signal (DI function 1: S-ON). If it is, check whether the corresponding DI terminal logic is valid. If it is invalid,please make it valid. Refer to __[[Group P06 DI/DO configuration>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/09%20Parameters/#HGroupP06DI2FDOconfiguration]]__
++✎Check whether group P06 is set the servo enable signal (DI function 1: S-ON). If it is, check whether the corresponding DI terminal logic is valid. If it is invalid,please make it valid. Refer to __[[Group P06 DI/DO configuration>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#_Group%20P06%20DI/DO%20configuration]]__
--✎If group P06 parameters have set the servo enable signal, and the corresponding terminal logic is valid, but the panel still displays "rdy", check whether the DI terminal wiring is correct, please refer to__[[ 4 Wiring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/]]__
++✎If group P06 parameters have set the servo enable signal, and the corresponding terminal logic is valid, but the panel still displays "rdy", check whether the DI terminal wiring is correct, please refer to__[[ 4 Wiring>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#_Wiring]]__
  )))
  |Control mode error|Check whether the parameter P00-01 is set correctly
--|(% style="vertical-align:middle" %)Panel display Er.xx|(% colspan="2" %)Refer to [[10.2 Handling of faults and warnings during operation>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
++|(% style="vertical-align:middle" %)Panel display Er.xx|(% colspan="2" %)Refer to [[10.2 Handling of faults and warnings during operation>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
  |(% colspan="3" style="vertical-align:middle" %)After troubleshooting, the servo drive panel should display "run"
  |(% rowspan="2" style="vertical-align:middle" %)Input torque instruction|(% style="vertical-align:middle" %)The motor does not rotate|U0-03 (input instruction pulse number) always displays 0|(((
  ✎AI wiring error
--When selecting analog input signal, make sure that the connection of analog input terminal is correct. Refer to__[[ 4 Wiring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/]]__.
++When selecting analog input signal, make sure that the connection of analog input terminal is correct. Refer to__[[ 4 Wiring>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#_Wiring]]__.
  ✎Not input speed instruction or speed instruction abnormal
@@ -114,20 +114,20 @@
  )))
  |(% style="vertical-align:middle" %)Control the supply voltage failure|(% style="vertical-align:middle" %)Measures the AC voltage between L1C &L2C.
  |(% style="vertical-align:middle" %)Servo drive fault|(% style="vertical-align:middle" %)Contact the agent or customer service
--|(% style="vertical-align:middle" %)Panel display “Er.xx”|(% colspan="2" style="vertical-align:middle" %)Refer to [[10.2 Handling of faults and warnings during operation>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
++|(% style="vertical-align:middle" %)Panel display “Er.xx”|(% colspan="2" style="vertical-align:middle" %)Refer to [[10.2 Handling of faults and warnings during operation>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
  |(% colspan="3" style="vertical-align:middle" %)After removing the fault, the servo drive panel should display "rdy"
  |(% rowspan="4" style="vertical-align:middle" %)Servo drive enable signal is valid(S-ON is ON)|(% rowspan="2" style="vertical-align:middle" %)The axis of servo motor is in a free running state|(% style="vertical-align:middle" %)Servo enable signal is invalid|(% style="vertical-align:middle" %)(((
--✎Check whether group P06 is set the servo enable signal (DI function 1: S-ON). If it is, check whether the corresponding DI terminal logic is valid. If it is invalid,please make it valid. Refer to __[[Group P06 DI/DO configuration>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/09%20Parameters/#HGroupP06DI2FDOconfiguration]]__
++✎Check whether group P06 is set the servo enable signal (DI function 1: S-ON). If it is, check whether the corresponding DI terminal logic is valid. If it is invalid,please make it valid. Refer to __[[Group P06 DI/DO configuration>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#_Group%20P06%20DI/DO%20configuration]]__
--✎If group P06 parameters have set the servo enable signal, and the corresponding terminal logic is valid, but the panel still displays "rdy", check whether the DI terminal wiring is correct, please refer to__[[ 4 Wiring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/]]__
++✎If group P06 parameters have set the servo enable signal, and the corresponding terminal logic is valid, but the panel still displays "rdy", check whether the DI terminal wiring is correct, please refer to__[[ 4 Wiring>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#_Wiring]]__
  )))
  |(% style="vertical-align:middle" %)Control mode error|(% style="vertical-align:middle" %)Check whether the parameter P00-01 is set correctly
--|(% style="vertical-align:middle" %)Panel display Er.xx|(% colspan="2" style="vertical-align:middle" %)Refer to [[10.2 Handling of faults and warnings during operation>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
++|(% style="vertical-align:middle" %)Panel display Er.xx|(% colspan="2" style="vertical-align:middle" %)Refer to [[10.2 Handling of faults and warnings during operation>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/10%20Malfunctions/#HFaultsandwarningshandlingduringoperation]]
  |(% colspan="3" style="vertical-align:middle" %)After troubleshooting, the servo drive panel should display "run"
  |(% rowspan="2" style="vertical-align:middle" %)Input speed instruction|(% style="vertical-align:middle" %)The motor does not rotate|(% style="vertical-align:middle" %)U0-03 (input instruction pulse number) always displays 0|(% style="vertical-align:middle" %)(((
  ✎AI wiring error
--When selecting analog input signal, make sure that the connection of analog input terminal is correct. Refer to__[[ 4 Wiring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/]]__.
++When selecting analog input signal, make sure that the connection of analog input terminal is correct. Refer to__[[ 4 Wiring>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#_Wiring]]__.
  ✎Not input torque instruction
@@ -145,23 +145,28 @@
  = **Overview** =
++
++(% style="text-align:center" %)
++[[image:ksjakfjk.png]]
++
  The faults and warnings of Wecon VD2 series servo drives are graded according to their severity, which can be divided into four grades: Category 1, Category 2, Category 3, Category 4. Severity level: Category 1> Category 2> Category 3 > Category 4, the specific classifications are as follows:
--* Category 1: faults cannot be cleared;
--* Category 2: faults are clearable;
--* Category 3: faults are clearable;
--* Category 4: warnings are clearable.
++Category 1: faults cannot be cleared;
++Category 2: faults are clearable;
++
++Category 3: faults are clearable;
++
++Category 4: warnings are clearable.
++
  Among them, "clearable" means that the panel stops the fault display state by giving a "clear signal". The specific operations are as follows:
 . Set the function code P10-03=1 (fault clearing) or use DI function 02 (02-A-CLR, fault and warning clearing) and set it to logic valid, which can stop the fault display on the panel.
 . The clearing method of category 2 and category 3 clearable faults: first turn off the servo enable signal (set S-ON to OFF), then set P10-03=1 or use DI function 02.
--1. The clearing method of category 4 of clearable warnings: set P10-03=1 or use DI function 02.
++1. The clearing method of category 4 of clearable warnings: set P10-03=1 or use DI function 02.[[image:image-20220611130000-2.png]]
++1. [[image:image-20220611130024-3.png]]
--|(% style="text-align:center; vertical-align:middle" %)(((
--(% style="text-align:center" %)
--[[image:ksjakfjk.png]]
--)))
++|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611125934-1.png]]
  |For some faults and warnings, you must change the settings to eliminate the causes before they can be cleared, but clearing does not mean that the changes take effect. For the changes that need to be re-powered to take effect, the power must be re-powered. For the changes that need to be stopped to take effect, the servo enable must be turned off. After the change takes effect, the servo drive can operate normally.
  Associated function codes
@@ -194,41 +194,149 @@
  VD2 series servo drives have a fault recording function, which could record the last 5 faults and the last 5 warning names and the status parameters of servo drive when the fault or warning occurs. After the fault or warning is cleared, the fault record will still save the fault and warning.
--The current fault code could be viewed through the monitoring parameter U1-01, and the current warning code could be viewed through U1-02. The monitoring U1-16 to U1-25 could display the last 5 fault codes and warning codes. Please refer to __[[Group U1 Warning monitoring>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/09%20Parameters/#HGroupU1Warningmonitoring]]__.
++The current fault code could be viewed through the monitoring parameter U1-01, and the current warning code could be viewed through U1-02. The monitoring U1-16 to U1-25 could display the last 5 fault codes and warning codes. Please refer to __[[Group U1 Warning monitoring>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/11%20Appendix/#HGroupU1Warningmonitoring]]__.
  == **Fault and warning code table** ==
  **(1) The first category (category 1 for short) The fault could not be cleared**
--|(% style="width:114px" %)**Category**|(% style="width:300px" %)**Error name**|(% style="width:92px" %)**Fault code**|(% style="width:330px" %)**Content**|(% style="width:105px" %)**Whether Clearable**|(% style="width:135px" %)**Operation**
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Parameter destruction|(% style="width:92px" %)Er.01|(% style="width:330px" %)Abnormal servo internal parameters|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Parameter storage error|(% style="width:92px" %)Er.02|(% style="width:330px" %)Abnormal servo internal parameters|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)ADC reference source faults|(% style="width:92px" %)Er.03|(% style="width:330px" %)Abnormal ADC reference source|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)AD current sampling conversion error|(% style="width:92px" %)Er.04|(% style="width:330px" %)AD current sampling conversion error|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Abnormal FPGA communication|(% style="width:92px" %)Er.05|(% style="width:330px" %)Abnormal FPGA communication|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Wrong FPGA program version|(% style="width:92px" %)Er.06|(% style="width:330px" %)Wrong FPGA program version|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Clock abnormal|(% style="width:92px" %)Er.07|(% style="width:330px" %)Clock abnormal|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)ADC conversion undone|(% style="width:92px" %)Er.60|(% style="width:330px" %)ADC conversion error|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Internal software fault|(% style="width:92px" %)Er.61|(% style="width:330px" %)Abnormal servo internal software|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Internal software fault|(% style="width:92px" %)Er.62|(% style="width:330px" %)Abnormal servo internal software|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Internal software fault|(% style="width:92px" %)Er.63|(% style="width:330px" %)Abnormal servo internal software|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Internal software fault|(% style="width:92px" %)Er.64|(% style="width:330px" %)Abnormal servo internal software|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Internal software fault|(% style="width:92px" %)Er.65|(% style="width:330px" %)Abnormal servo internal software|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Motor model error|(% style="width:92px" %)Er.26|(% style="width:330px" %)Motor model error|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Encoder Z pulse lost|(% style="width:92px" %)Er.28|(% style="width:330px" %)Encoder Z pulse lost|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Encoder UVW signal error|(% style="width:92px" %)Er.30|(% style="width:330px" %)Encoder UVW signal error|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)(((
--Exceeds motor
++|(% style="text-align:center; vertical-align:middle; width:96px" %)**Category**|(% style="text-align:center; vertical-align:middle; width:274px" %)**Error name**|(% style="text-align:center; vertical-align:middle; width:377px" %)**Cause of fault**|(% style="text-align:center; vertical-align:middle; width:119px" %)**Fault code**|(% style="text-align:center; vertical-align:middle; width:605px" %)**Troubleshooting**
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)Parameter destruction|(% style="vertical-align:middle; width:377px" %)EEPROM could not be read and written|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.01|(% style="vertical-align:middle; width:605px" %)The hardware interface could not read and write parameters, please contact the manufacturer to confirm whether the hardware is damaged.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Parameter storage error
++)))|(% style="vertical-align:middle; width:377px" %)(((
++Exceptions such as the version, total number, range, and validation failure of internal parameter storage.
--maximum speed
--)))|(% style="width:92px" %)Er.32|(% style="width:330px" %)(((
--Exceeds motor
++Possible reasons are:
--maximum speed
--)))|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)Over current|(% style="width:92px" %)Er.20|(% style="width:330px" %)Servo drive hardware overcurrent|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
--|(% style="width:114px" %)Category 1|(% style="width:300px" %)The brake resistor is turned on abnormally|(% style="width:92px" %)Er.24|(% style="width:330px" %)The brake resistor of servo drive is turned on abnormally|(% style="width:105px" %)No|(% style="width:135px" %)Stop immediately
++✎The drive has undergone a software upgrade
++✎In the process of parameter storage, an instantaneous power failure occurs
++
++✎Frequent writing of parameters
++)))|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.02|(% style="vertical-align:middle; width:605px" %)(((
++✎Check whether the program has been updated. If the parameter storage is abnormal due to the updated program, please update the parameters by restoring the factory default parameters and power on again.
++
++✎Re-power on and reset the parameters after restoring the factory default settings;
++
++✎Confirm whether the host computer writes parameters frequently, and modify the corresponding parameter writing method;
++)))
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)ADC reference source faults|(% style="vertical-align:middle; width:377px" %)The internal analog reference source of the drive is not accurate|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.03|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)AD current sampling conversion error|(% style="vertical-align:middle; width:377px" %)Current sampling zero drift or current sensor error|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.04|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)FPGA communication abnormal|(% style="vertical-align:middle; width:377px" %)FPGA communication faults|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.05|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)The FPGA program version is wrong|(% style="vertical-align:middle; width:377px" %)The FPGA program version is wrong|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.06|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)Clock abnormal|(% style="vertical-align:middle; width:377px" %)The internal clock of the drive is disturbed or abnormal|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.07|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++ADC conversion undone
++)))|(% style="vertical-align:middle; width:377px" %)ADC conversion is not complete|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.60|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Internal software Fault
++)))|(% style="vertical-align:middle; width:377px" %)Torque loop error|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.61|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Internal software Fault
++)))|(% style="vertical-align:middle; width:377px" %)Speed loop error|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.62|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Internal software Fault
++)))|(% style="vertical-align:middle; width:377px" %)Illegal instruction|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.63|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Internal software Fault
++)))|(% style="vertical-align:middle; width:377px" %)Internal RAM parameter destruction|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.64|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Internal software Fault
++)))|(% style="vertical-align:middle; width:377px" %)Internal function code parameter destruction|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.65|(% style="vertical-align:middle; width:605px" %)Please power on again to determine whether the fault is eliminated; if there is still an abnormality, please contact the manufacturer.
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Motor model error
++)))|(% style="vertical-align:middle; width:377px" %)Incorrect motor model|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.26|(% style="vertical-align:middle; width:605px" %)Check whether the function code motor model setting is correct
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)Encoder Z pulse lost|(% style="vertical-align:middle; width:377px" %)(((
++No Z pulse signal appears when the motor rotates more than one turn.
++
++The possible reasons are:
++
++✎Wrong motor model
++
++✎The motor encoder is disturbed or damaged;
++)))|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.28|(% style="vertical-align:middle; width:605px" %)(((
++✎Check whether the motor model matches the drive model.
++
++✎Replace the motor and power on again.
++)))
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)Incremental encoder AB count is not equal to encoder line number*4|(% style="vertical-align:middle; width:377px" %)(((
++Incremental encoder AB count is not equal to encoder line number*4.
++
++The possible reasons are:
++
++✎The motor model is wrong;
++
++✎Hand interference or damage to the motor encoder;
++)))|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.29|(% style="vertical-align:middle; width:605px" %)(((
++✎Check whether the motor model matches the drive model.
++
++✎Replace the motor model that matches the drive.
++)))
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)Encoder UVW signal error|(% style="vertical-align:middle; width:377px" %)Motor encoder UVW signal error|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.30|(% style="vertical-align:middle; width:605px" %)(((
++✎Check whether the motor model matches the drive model
++
++✎Replace the motor model that matches the drive.
++
++✎Replace encoder line
++)))
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:274px" %)(((
++Exceeds motor maximum speed
++)))|(% style="vertical-align:middle; width:377px" %)(((
++Exceeding the maximum speed threshold of function code P1-10. Possible reasons are:
++
++✎Wrong U/V/W phase sequence of motor power line
++
++✎Wrong t motor model
++
++✎Wrong transfer wiring of motor power line
++
++✎Wrong wiring of motor encoder
++)))|(% style="text-align:center; vertical-align:middle; width:119px" %)Er.32|(% style="vertical-align:middle; width:605px" %)(((
++✎Please check whether the motor power line is correctly wired;
++
++✎Confirm whether the motor model is correct;
++
++✎Use the correct power line and encoder line transfer wiring;
++)))
++
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:273px" %)Overcurrent|(% style="width:379px" %)(((
++The drive detects that the power device has overcurrent, the possible situations are:
++
++✎The motor power lines U, V, W are short-circuited to the ground
++
++✎Short circuit between the motor power lines U, V, W
++
++✎The motor power lines U, V, W have poor contact
++
++✎The internal damage of motor
++
++✎The encoder cable is aging and loose
++
++✎Excessive fluctuation of control power supply.
++)))|(% style="text-align:center; vertical-align:middle; width:118px" %)Er.20|(% style="vertical-align:middle; width:605px" %)(((
++✎Please check whether the wiring of the motor power line is correct
++
++✎Whether the wiring of the motor power line is loose or short-circuited
++
++✎Replace the motor power line transfer line
++
++✎Replace the motor
++
++✎Replace the encoder transfer line
++
++✎If the above methods still cannot eliminate the fault, please contact the manufacturer.
++)))
++|(% style="text-align:center; vertical-align:middle; width:96px" %)Category 1|(% style="text-align:center; vertical-align:middle; width:273px" %)(((
++Braking resistor turns on abnormally
++)))|(% style="width:379px" %)(((
++The braking resistor bleeder is turned on, but no feedback signal is detected. The possible reasons are:
++
++✎The braking resistor failed to open;
++
++✎Braking resistor feedback detection faults;
++)))|(% style="text-align:center; vertical-align:middle; width:118px" %)Er.24|(% style="vertical-align:middle; width:605px" %)The circuit of the brake release part may be damaged, please contact the manufacturer
++
  **(2)The 2nd category (category 2 for short) clearable faults**
  |(% style="text-align:center; vertical-align:middle; width:97px" %)**Category**|(% style="text-align:center; vertical-align:middle; width:276px" %)**Error name**|(% style="text-align:center; vertical-align:middle; width:379px" %)**Cause of fault**|(% style="text-align:center; vertical-align:middle; width:118px" %)**Fault code**|(% style="text-align:center; vertical-align:middle; width:601px" %)**Troubleshooting**
@@ -475,4 +475,4 @@
  check abnormal and frequency is too high
  )))|(% style="vertical-align:middle; width:383px" %)Encoder communication has timeout or CRC check error|(% style="text-align:center; vertical-align:middle; width:121px" %)A-93|(% style="vertical-align:middle; width:593px" %)Check whether the encoder wiring is disturbed
--The “**✎Note” **section describes how to handle the warning of "Duplicate DI port configuration" of VD2-0XXSA1G. Due to the number of DI ports, the function codes of VD2F-0xxSA1P are different. Please refer to __[[Group P06 DI/DO configuration>>https://docs.we-con.com.cn/bin/view/Servo/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/09%20Parameters/#HGroupP06DI2FDOconfiguration]]__
++The “**✎Note” **section describes how to handle the warning of "Duplicate DI port configuration" of VD2-0XXSA1G. Due to the number of DI ports, the function codes of VD2F-0xxSA1P are different. Please refer to __[[Group P06 DI/DO configuration>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/11%20Appendix/#HGroupP06DIDOconfiguration]]__

Changes for page 10 Malfunctions

Summary

Details

Navigation

Table of Contents