Skip to Content

Changes for page VD2 SA Series

Last modified by Iris on 2025/08/02 17:40
From version 16.2
edited by Mora Zhou
on 2025/04/28 09:16
Change comment: There is no comment for this version
To version 23.1
edited by Iris
on 2025/08/02 17:34
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Mora
1 +XWiki.Iris
Content
... ... @@ -1,6 +1,6 @@
1 1  = **Preface** =
2 2  
3 -This manual is applicable to Wecon VD2 Series absolute value servo drives (**VD2/VD2F/VD2L**).
3 +This manual is applicable to Wecon VD2 Series absolute value servo drives (**VD2 SA series**).
4 4  
5 5  In order to use this series of servo drives correctly, please read this manual carefully in advance and save it for later use.
6 6  
... ... @@ -35,7 +35,7 @@
35 35  
36 36  VD2F-0□□SA1P model: V1.00
37 37  )))
38 -|2022.3|A1.1|(((
38 +|2022.03|A1.1|(((
39 39  Chapter 2 Updating the servo driver naming, updating motor model table.
40 40  
41 41  Chapter 3 Updating motor dimension drawing and dimension table
... ... @@ -48,7 +48,7 @@
48 48  
49 49  VD2F-0□□SA1P model: Add V1.01 and V1.02
50 50  )))
51 -|2022.4|A1.2|(((
51 +|2022.04|A1.2|(((
52 52  Chapter 2 Updating section 2.1 “Servo Drive Specifications”
53 53  
54 54  Chapter 4 Updating section 4.1 “Main Circuit Wiring”, updating section 4.5 “Communication signal wiring”
... ... @@ -88,7 +88,7 @@
88 88  
89 89  Add V1.17 firmware
90 90  )))
91 -|2023.06|V2.1|(((
91 +|2023.05|V2.1|(((
92 92  Chapter 6 Updating section 6.17 “Shutdown deceleration time” setting feature. Updating section 6.63 “P10-6 Multi-turn Absolute Encoder Reset” and “P10-8: Multi-turn Absolute Encoder Origin Offset Compensation” Updating section 6.64 "P00-31 Encoder Read and Write Verification Abnormal Threshold Setting"
93 93  
94 94  Chapter 10 add “Er.43 Drive Overload Fail” and parameter content. Add “A80 Drive Overload Alarm” Modify “A91 Parameter Modification too Frequent Warning” trigger condition. Add temporary solution for "A93 encoder read and write verification abnormal frequency is too high"
... ... @@ -188,31 +188,32 @@
188 188  
189 189  Revise ER.27 Not clearable properties;
190 190  )))|(((
191 -Update V1.20 firmware
191 +Update V1.20 firmware
192 192  
193 -Add VD2L series model
193 +Add VD2L series model
194 194  
195 -Add VD2-050TA1G model
195 +Add VD2-050TA1G model
196 196  )))
197 -|2024.09|V2.3|(((
198 -Chapter 2.13 "Basic Specifications"
197 +|2024.12|V2.4|(((
198 +Chapter 6, added section 6.8 “Home Return Mode (HM)”;
199 199  
200 -Chapter 3.13 "Installation environment of servo drive"
200 +Chapter 9: Revised the content of "P00-04 Function Code";
201 201  
202 -Add 3.23 “Installation environment of servo motor"
202 +Added "Group P01: P01-39; P01-40; P01-41; P01-42; P01-43; P01-44 ";
203 +
204 +Added "U0 Group: U0-59 bus voltage historical maximum and U0-60 average power historical maximum;
205 +
206 +Chapter 10, Section 10.3, added ER.19 Software Overcurrent;
203 203  )))|(((
204 -Add environmental condition description changes
205 -)))
206 -|2025.1|V2.4| |(((
207 -VD2 V1.22 Firmware
208 +Added VD2 series V1.22 firmware
208 208  
209 -VD2L V1.02 Firmware
210 +Added VD2L V1.02 firmware
210 210  )))
211 211  
212 212  The following table lists the servo driver models and supported firmware.
213 213  
214 -| |**Supported models**|**Corresponding model**|**Voltage**|**Supported firmware**
215 -|(% colspan="1" rowspan="16" %)**Wecon VD2SA series servo drives manual**|VD2-010SA1G|(% rowspan="2" %)VD2A|(% rowspan="12" %)220V|(% rowspan="7" %)(((
215 +| | | |**Supported models**|**Corresponding model**|**Voltage**|**Supported firmware**
216 +|(% rowspan="18" %) |(% rowspan="18" %) |(% colspan="1" rowspan="18" %)**Wecon VD2SA series servo drives manual**|VD2-010SA1G|(% rowspan="2" %)VD2 A type|(% rowspan="12" %)220V|(% rowspan="7" %)(((
216 216  V1.10
217 217  
218 218  V1.12
... ... @@ -232,9 +232,13 @@
232 232  V1.19
233 233  
234 234  V1.20
236 +
237 +V1.21
238 +
239 +V1.22
235 235  )))
236 236  |VD2-014SA1G
237 -|VD2-016SA1G|(% rowspan="5" %)VD2B
242 +|VD2-016SA1G|(% rowspan="5" %)VD2 B type
238 238  |VD2-019SA1G
239 239  |VD2-021SA1G
240 240  |VD2-025SA1GF
... ... @@ -251,12 +251,28 @@
251 251  V1.17
252 252  
253 253  V1.18
259 +
260 +V1.19
261 +
262 +V1.20
263 +
264 +V1.21
265 +
266 +V1.22
254 254  )))
255 255  |VD2F-010SA1P
256 256  |VD2F-014SA1P
257 -|VD2L-010SA1P|(% rowspan="2" %)VD2L|(% rowspan="2" %)V1.00
270 +|VD2L-010SA1P|(% rowspan="2" %)VD2L|(% rowspan="2" %)(((
271 +V1.00
272 +
273 +V1.01
274 +
275 +V1.02
276 +)))
258 258  |VD2L-014SA1P
259 -|VD2-021TA1G|VD2B|(% colspan="1" rowspan="4" %)380V|(((
278 +|(((
279 +VD2-016TA1G
280 +)))|(% colspan="1" rowspan="3" %)VD2 B type|(% colspan="1" rowspan="6" %)380V|(% colspan="1" rowspan="3" %)(((
260 260  V1.01
261 261  
262 262  V1.17
... ... @@ -266,7 +266,21 @@
266 266  V1.19
267 267  
268 268  V1.20
290 +
291 +V1.21
292 +
293 +V1.22
269 269  )))
270 -|VD2-030TA1G|(% rowspan="3" %)VD2C|(% rowspan="3" %)V1.20
295 +|(((
296 +VD2-019TA1G
297 +)))
298 +|VD2-021TA1G
299 +|VD2-030TA1G|(% rowspan="3" %)VD2 C type|(% rowspan="3" %)(((
300 +V1.20
301 +
302 +V1.21
303 +
304 +V1.22
305 +)))
271 271  |VD2-040TA1G
272 -|VD2-0250TA1G
307 +|VD2-050TA1G