Skip to Content

Changes for page VD2 SA Series

Last modified by Iris on 2025/08/02 17:40
From version 20.1
edited by Iris
on 2025/07/18 16:25
Change comment: There is no comment for this version
To version 23.2
edited by Iris
on 2025/08/02 17:38
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -35,7 +35,7 @@
35 35  
36 36  VD2F-0□□SA1P model: V1.00
37 37  )))
38 -|2022.3|A1.1|(((
38 +|2022.03|A1.1|(((
39 39  Chapter 2 Updating the servo driver naming, updating motor model table.
40 40  
41 41  Chapter 3 Updating motor dimension drawing and dimension table
... ... @@ -48,7 +48,7 @@
48 48  
49 49  VD2F-0□□SA1P model: Add V1.01 and V1.02
50 50  )))
51 -|2022.4|A1.2|(((
51 +|2022.04|A1.2|(((
52 52  Chapter 2 Updating section 2.1 “Servo Drive Specifications”
53 53  
54 54  Chapter 4 Updating section 4.1 “Main Circuit Wiring”, updating section 4.5 “Communication signal wiring”
... ... @@ -88,7 +88,7 @@
88 88  
89 89  Add V1.17 firmware
90 90  )))
91 -|2023.06|V2.1|(((
91 +|2023.05|V2.1|(((
92 92  Chapter 6 Updating section 6.17 “Shutdown deceleration time” setting feature. Updating section 6.63 “P10-6 Multi-turn Absolute Encoder Reset” and “P10-8: Multi-turn Absolute Encoder Origin Offset Compensation” Updating section 6.64 "P00-31 Encoder Read and Write Verification Abnormal Threshold Setting"
93 93  
94 94  Chapter 10 add “Er.43 Drive Overload Fail” and parameter content. Add “A80 Drive Overload Alarm” Modify “A91 Parameter Modification too Frequent Warning” trigger condition. Add temporary solution for "A93 encoder read and write verification abnormal frequency is too high"
... ... @@ -194,7 +194,20 @@
194 194  
195 195  Add VD2-050TA1G model
196 196  )))
197 -|2024.11|V2.4|(((
197 +|(((
198 +2024.09
199 +)))|(((
200 +V2.3
201 +)))|(((
202 +Chapter 2 Amend subsection 2.13 “Basic specifications”
203 +
204 +Chapter 3  Add a new subsection 3.13 “Installation environment for servo drives”
205 +
206 +Addition of subsection 3.23 “Installation environment for servomotors”
207 +)))|(((
208 +New changes to the description of environmental conditions
209 +)))
210 +|2024.12|V2.4|(((
198 198  Chapter 6, added section 6.8 “Home Return Mode (HM)”;
199 199  
200 200  Chapter 9: Revised the content of "P00-04 Function Code";
... ... @@ -212,8 +212,8 @@
212 212  
213 213  The following table lists the servo driver models and supported firmware.
214 214  
215 -| |**Supported models**|**Corresponding model**|**Voltage**|**Supported firmware**
216 -|(% colspan="1" rowspan="16" %)**Wecon VD2SA series servo drives manual**|VD2-010SA1G|(% rowspan="2" %)VD2A|(% rowspan="12" %)220V|(% rowspan="7" %)(((
228 +| | | |**Supported models**|**Corresponding model**|**Voltage**|**Supported firmware**
229 +|(% rowspan="18" %) |(% rowspan="18" %) |(% colspan="1" rowspan="18" %)**Wecon VD2SA series servo drives manual**|VD2-010SA1G|(% rowspan="2" %)VD2 A type|(% rowspan="12" %)220V|(% rowspan="7" %)(((
217 217  V1.10
218 218  
219 219  V1.12
... ... @@ -239,7 +239,7 @@
239 239  V1.22
240 240  )))
241 241  |VD2-014SA1G
242 -|VD2-016SA1G|(% rowspan="5" %)VD2B
255 +|VD2-016SA1G|(% rowspan="5" %)VD2 B type
243 243  |VD2-019SA1G
244 244  |VD2-021SA1G
245 245  |VD2-025SA1GF
... ... @@ -275,7 +275,9 @@
275 275  V1.02
276 276  )))
277 277  |VD2L-014SA1P
278 -|VD2-021TA1G|VD2B|(% colspan="1" rowspan="4" %)380V|(((
291 +|(((
292 +VD2-016TA1G
293 +)))|(% colspan="1" rowspan="3" %)VD2 B type|(% colspan="1" rowspan="6" %)380V|(% colspan="1" rowspan="3" %)(((
279 279  V1.01
280 280  
281 281  V1.17
... ... @@ -290,7 +290,11 @@
290 290  
291 291  V1.22
292 292  )))
293 -|VD2-030TA1G|(% rowspan="3" %)VD2C|(% rowspan="3" %)(((
308 +|(((
309 +VD2-019TA1G
310 +)))
311 +|VD2-021TA1G
312 +|VD2-030TA1G|(% rowspan="3" %)VD2 C type|(% rowspan="3" %)(((
294 294  V1.20
295 295  
296 296  V1.21
... ... @@ -298,4 +298,4 @@
298 298  V1.22
299 299  )))
300 300  |VD2-040TA1G
301 -|VD2-0250TA1G
320 +|VD2-050TA1G