Skip to Content
Last modified by nozzin on 2024/02/26 09:16
From version 12.1
edited by nozzin
on 2024/02/26 09:16
Change comment: There is no comment for this version
To version 9.1
edited by Mora Zhou
on 2024/02/23 13:58
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -Wecon LX6C Parallel Robot Project
1 +Wecon LX6C Delta Robot Project
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.nozzin
1 +XWiki.Mora
Content
... ... @@ -1,6 +1,6 @@
1 1  = 1 Introduction =
2 2  
3 -This project uses Wecon Codesys PLC LX6C and bus type servo VD3E for parallel robot control. Through simple debugging, the point-to-point interpolation motion of the delta robot is realized.
3 +This project uses Wecon Codesys PLC LX6C and bus type servo VD3E for delta robot control. Through simple debugging, the point-to-point interpolation motion of the delta robot is realized.
4 4  
5 5  = 2 Main kit composition =
6 6  
... ... @@ -117,49 +117,50 @@
117 117  
118 118  == 5.2 Connect LX6C ==
119 119  
120 -**Double click “Device” and select Scan Network**
120 +Double click “Device” and select Scan Network
121 121  
122 -**Select LX6C and click OK, make sure your PC and LX6C in the same LAN (LX6C default IP is 192.168.8.8)**
122 +Select LX6C and click OK, make sure your PC and LX6C in the same LAN (LX6C default IP is 192.168.8.8)
123 123  
124 124  (% style="text-align:center" %)
125 125  [[image:1708659630178-665.png]]
126 126  
127 -**Login device with account and password**
127 +Login device with account and password
128 128  
129 129  (% style="text-align:center" %)
130 130  [[image:1708659646762-832.png]]
131 131  
132 +
132 132  = 6 Project configuration =
133 133  
134 134  == 6.1 Add Axis Group ==
135 135  
136 -**Right click Application, “Add Object” and select “Axis Group”**
137 +Right click Application, “Add Object” and select “Axis Group”
137 137  
138 138  
139 139  (% style="text-align:center" %)
140 140  [[image:1708659668179-463.png]]
141 141  
142 -**Click “Select Kinematics” and select “TRAFO.Kin_Tripod_Rotary”**
143 +Click “Select Kinematics” and select “TRAFO.Kin_Tripod_Rotary”
143 143  
144 144  (% style="text-align:center" %)
145 145  [[image:1708659683686-935.png]]
146 146  
147 -**Fill in the mechanical parameters (Use the same user units)**
148 +Fill in the mechanical parameters (Use the same user units)
148 148  
149 149  (% style="text-align:center" %)
150 150  [[image:1708659724005-484.png]]
151 151  
152 -**Right click “Device” and add device**
153 +Right click “Device” and add device
153 153  
154 154  (% style="text-align:center" %)
155 155  [[image:1708659738998-621.png]]
156 156  
157 -**Add “EtherCAT Master SoftMotion”**
158 +Add “EtherCAT Master SoftMotion”
158 158  
159 159  (% style="text-align:center" %)
160 160  [[image:1708659810951-477.png]]
161 161  
162 -**Right click “EtherCAT_Master_SoftMotion” and add device, select “Wecon VD3E EtherCAT Servo_v1.10” (Servo xml file should be same with servo firmware, you can check servo firmware in U2-04 through servo panel)**
163 +Right click “EtherCAT_Master_SoftMotion” and add device, select “Wecon VD3E EtherCAT Servo_v1.10” (Servo xml file should be same with servo firmware, you can check servo firmware in U2-04 through servo panel)
163 163  
164 164  (% style="text-align:center" %)
165 165  [[image:1708659837241-566.png]]
... ... @@ -168,27 +168,27 @@
168 168  (% style="text-align:center" %)
169 169  [[image:1708659844978-946.png]]
170 170  
171 -**Add 3 motion axis**
172 +Add 3 motion axis
172 172  
173 173  (% style="text-align:center" %)
174 174  [[image:1708659868961-294.png]]
175 175  
176 -**Set the correct resolution based on the motor encoder**
177 +Set the correct resolution based on the motor encoder
177 177  
178 178  (% style="text-align:center" %)
179 179  [[image:1708659882131-694.png]]
180 180  
181 -**Double click “EtherCAT_Master_SoftMotion” and select network name “eth1” in “General”**
182 +Double click “EtherCAT_Master_SoftMotion” and select network name “eth1” in “General”
182 182  
183 183  (% style="text-align:center" %)
184 184  [[image:1708659902425-597.png]]
185 185  
186 -**Bind axis to robot.**
187 +Bind axis to robot.
187 187  
188 188  (% style="text-align:center" %)
189 189  [[image:1708659921571-879.png]]
190 190  
191 -**Move “PLC_PRG” from “MainTask” to “EtherCAT_Task”**
192 +Move “PLC_PRG” from “MainTask” to “EtherCAT_Task”
192 192  
193 193  (% style="text-align:center" %)
194 194  [[image:1708660033766-909.png]]
... ... @@ -198,7 +198,7 @@
198 198  
199 199  == 6.2 Demo program ==
200 200  
201 -**Build a simple program for absolute move**
202 +Build a simple program for absolute move
202 202  
203 203  (% style="text-align:center" %)
204 204  [[image:1708660054738-287.png]]