Skip to Content

Wiki source code of 1 V-BOX Hardware Interface

Version 15.1 by Hunter on 2022/12/15 11:44
Show last authors
1 = **V-BOX Hardware Interface** =
2
3 **Hardware interface of V-BOX H series**
4
5 (% style="text-align:center" %)
6 (((
7 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
8 [[H series>>image:1598675141041.png||height="401" id="I1598675141041.png" width="600"]]
9 )))
10
11 **Hardware interface of V-BOX S series**
12
13 (% style="text-align:center" %)
14 (((
15 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
16 [[S series 1>>image:V-BOX.V-Net.Download.Repair.WebHome@1598674812088.png||height="361" id="IV-BOX.V-Net.Download.Repair.WebHome401598674812088.png" width="600"]]
17 )))
18
19
20 (% style="text-align:center" %)
21 (((
22 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
23 [[S series 2>>image:V-BOX.V-Net.Download.Repair.WebHome@1598674852318.png||height="384" id="IV-BOX.V-Net.Download.Repair.WebHome401598674852318.png" width="600"]]
24 )))
25
26 **Hardware interface of V-BOX E series**
27
28 (% style="text-align:center" %)
29 (((
30 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
31 [[E series>>image:1598674997778.png||height="383" id="I1598674997778.png" width="600"]]
32 )))
33
34 = **V-BOX interface description** =
35
36 **Power interface:** DC24V power input interface.
37
38 * Please ground during use(especially S and E series) to prevent hardware from being burned due to interference. If the vbox is installed in an electric control cabinet, make sure that the electric control cabinet is also grounded.
39
40 **9-pin COM port:** used to communicate with various PLC brands, servos, single-chip Microcomputer, instruments and meters on the market, and supports RS232/RS422/RS485. For specific interface definitions, please refer to the "V-Box Pin Definition" chapter.
41
42 **Ethernet port:** It can be used to connect to the network and communicate with HMI, various PLC brands, servos, single-chip Microcomputer, instruments and other equipment.
43
44 **Antenna interface:** 4G, WIFI antenna interface, used to enhance the signal.
45
46 **IO contacts:** H series comes standard with 2 relay outputs (DO) and 2 optocoupler isolation inputs (DI).
47
48 **USB MINI interface:** used for configuration debugging and Box configuration download.
49
50 **Indicator light：**
51
52 * **Signal indicator:** Except the P/R, NET, LINK, COM led light on right side, those 4 signal lights on the left side used to indicate the signal strength of WiFi/4G.
53 ** Signal strength value of WiFi can be viewed by the internal register HSW146
54 ** Signal strength value of 4G can be viewed by the internal register HSW166
55 ** There are some different display for signal lights means V-Box connection on different status:
56 *** **4 signal lights are keep off**: Not recognize SIM card yet;
57 *** **Signal light 1 (Counting from top to bottom) is blinking**: SIM card status abnormal or signal abnormal;
58 *** **4 signal lights are blinking at the same time**: Not able to connect with 4G base station; 
59 *** **Signal light(s) is/are keep on** which means the connection is OK;
60 * **P/R light:** V-Box operation indicator, this light flashes when V-Box is operating normally.Otherwise,V-Box firmware do not run well.
61 * **NET ligh**t: network communication indicator. When the V-Box communicates with other devices through the network, this light flashes.
62 * **LINK light:** server connection indicator.
63 ** When the V-BOX is not connected to the network, this light is off;
64 ** When the V-BOX's network connection is normal, but not connected to the server, this light flashes;
65 ** When the V-BOX's network connection is normal and the server is successfully connected, this light is always on.
66 * **COM light:** serial port communication indicator. When the V-BOX communicates with other devices through the serial port, this light flashes.
67
68 (% class="box infomessage" %)
69 (((
70 **✎Note: **4G signal ranges from 0-31 (Greater than 20 represents signal is good)
71 WiFi signal ranges from 0-100 (Greater than 80 represents signal is good)
72 )))
73
74 **IO interface：**
75
76 * Xn: Switch signal input terminal, with optocoupler isolation input.
77 * Yn: Switch signal output terminal, relay output.
78 * S/S: Input mode selection terminal, S/S connected with 24V+ means supporting NPN input mode; S/S connected with 24V- means supporting PNP input mode.
79 * COM：Output common.
80
81 **RS485 communication terminal**
82
83 * A+: RS485+ terminal.
84 * B-: RS485- terminal.
85 * GND: Common ground terminal of RS485 terminal.