Inovance
H3U (serial)
V-BOX Settings
| Item | Settings | Note |
| Protocol | INOVANCE H3U PLC | |
| Connection | RS422 | |
| Baud rate | 9600 | |
| Data bit | 7 | |
| Parity | EVEN | |
| Stop bit | 1 | |
| PLC station No. | 0 |
Address List
| Type | Device registers | Format | Range | Note |
|---|---|---|---|---|
| Bit | X | X OOOOOO | 0~303237 | |
| Bit | Y | Y OOOOOO | 0~303237 | |
| Bit | M | M DDDDD | 0~99999 | |
| Bit | T | T DDDDD | 0~99999 | |
| Bit | C | C DDDDD | 0~99999 | |
| Bit | SM | SM DDDD | 8000~9999 | |
| Bit | S | S DDDDD | 0~99999 | |
| Bit | Lamp | Lamp0 | 0~0 | Communication Indicator Lamp 0: Connected 1: Disconnected |
| Word | X | X OOOOOO | 0~303237 | |
| Word | Y | Y OOOOOO | 0~303237 | |
| Word | M | M DDDDD | 0~99999 | |
| Word | T | T DDDDD | 0~99999 | |
| Word | C | C DDD | 0~199 | |
| Word | D | D DDDD | 0~7999 | |
| Word | S | S DDDDD | 0~99999 | |
| Word | SD | SD DDDD | 8000~9999 | |
| Word | R | R DDDDD | 0~32767 | |
| Double Word | CH | CH DDD | 200~255 |
PLC Settings
Create the new project, and select Series and models as H3U.
Configure the COM0 settings from [Communication Config]-[COM0(Download/HMI Monitor Protocol)], the default communication parameters we could see it is 9600,1,7,EVEN. After setting finished, click OK to save the settings.
Program the PLC project, and click compile.
Connect PLC with PC via USB cable or RS422-USB converter cable, and test the connection status. If it shows like the below, which means the connection is set up successfully. And click OK.
Download PLC program into PLC.
Cable Wiring
Figure
Pin Definition Diagram
H3U PLC Ethernet
Support Series: INOVANCE H3U Series
HMI Settings
| Item | Settings | Note |
|---|---|---|
| Protocol | INOVANCE H3U PLC Ethernet | |
| Connection | Ethernet | |
| Port No. | 502 | |
| Device No. | 1 | |
| HMI No. | 0 |
Address List
| Type | Device registers | Format | Range | Note |
|---|---|---|---|---|
| Bit | M | M DDDD | 0~8511 | |
| Bit | SM | SM DDDD | 0~1023 | |
| Bit | S | S DDDD | 0~4095 | |
| Bit | T | T DDD | 0~511 | |
| Bit | C | C DDD | 0~255 | |
| Bit | X | X OOO | 0~571 | |
| Bit | Y | Y OOO | 0~571 | |
| Word | D | D DDDD | 0~8511 | |
| Word | SD | SD DDDD | 0~1023 | |
| Word | R | R DDDDD | 0~32767 | |
| Word | T | T DDD | 0~255 | |
| Word | C | C DDD | 0~199 | |
| Double Word | C | C DDD | 200~255 |
PLC Settings
Create the new project, and select Series and models as H3U.
Configure the Ethernet settings from [Communication Config]-[Ethernet].
Program the PLC project, and click compile.
Connect PLC with PC via USB cable or RS422-USB converter cable, and test the connection status. If it shows like the below, which means the connection is set up successfully. And click OK.
If don't want to change the IP, user could also read the IP parameter from the PLC after the PC connection is set up successfully.
Download PLC program into PLC.
Cable Wiring
