Wiki source code of Mitsubishi

Version 43.1 by Theodore Xu on 2023/09/15 10:10

version	line-number	content
39.1	1	== FX1S,1N,2N Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX1S, FX1N, FX2N series
	4
37.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX1S/FX1N/FX2N\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
37.1	16	Address List
2.1	17
37.1	18	\|Type\|Device registers\|V-Box registers\|Format\|Range\|Note
2.1	19	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	20	\|Y\|Y\|Y o\|0~~303237\|
	21	\|M\|M\|M d\|0~~99999\|
	22	\|T\|T\|T d\|0~~99999\|
	23	\|C\|C\|C d\|0~~99999\|
	24	\|S\|S\|S d\|0~~99999\|
	25	\|SM\|SM\|SM d\|8000~~9999\|
	26	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	27	\|Y\|Y\|Y o\|0~~303237\|
	28	\|M\|M\|M d\|0~~99999\|
	29	\|T\|T\|T d\|0~~99999\|
	30	\|C\|C\|C d\|0~~199\|
	31	\|D\|D\|D d\|0~~7999\|
	32	\|S\|S\|S d\|0~~99999\|
	33	\|SD\|SD\|SD d\|8000~~9999\|
	34
37.1	35	Configure the communication protocol
2.1	36
	37	{{id name="Iimage-20220825102844-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dc262f14b14cf564.png\|\|alt="image-20220825102844-3.png" height="1011" width="1920"]]
	38
37.1	39	Cable Wiring
2.1	40
37.1	41	RS422
2.1	42
37.1	43	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_9294a40c62eb99be.png\|\|alt="image-20220825103350-4.png" height="284" width="723"]]
2.1	44
35.1	45	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	46
40.1	47	== FX3U,3G,3GA Serial ==
2.1	48
	49	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	50
38.1	51	V-BOX Settings
2.1	52
	53	\|Item\|Settings\|Note
	54	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	55	\|Connection\|RS422/RS485/RS232\|
	56	\|Baud rate\|9600~~115200\|
	57	\|Data bit\|7/8\|
	58	\|Parity\|EVEN/Odd/None\|
	59	\|Stop bit\|1/2\|
	60	\|PLC station No.\|1~~255\|
	61
38.1	62	Address List
2.1	63
	64	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	65	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	66	\|Y\|Y\|Y o\|0~~303237\|
	67	\|M\|M\|M d\|0~~99999\|
	68	\|T\|T\|T d\|0~~99999\|
	69	\|C\|C\|C d\|0~~99999\|
	70	\|S\|S\|S d\|0~~99999\|
	71	\|SM\|SM\|SM d\|8000~~9999\|
	72	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	73	\|Y\|Y\|Y o\|0~~303237\|
	74	\|M\|M\|M d\|0~~99999\|
	75	\|T\|T\|T d\|0~~99999\|
	76	\|C\|C\|C d\|0~~199\|
	77	\|D\|D\|D d\|0~~7999\|
	78	\|S\|S\|S d\|0~~99999\|
	79	\|SD\|SD\|SD d\|8000~~9999\|
	80
38.1	81	Configure the communication protocol
2.1	82
38.1	83	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_4d2a4921240d23c6.png\|\|alt="image-20220825102649-2.png" height="1009" width="1920"]]
2.1	84
42.1	85	PLC Setting
2.1	86
42.1	87	Open GX Works2, create a new PLC project or open the project that has been created.
	88	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	89
	90	(% style="text-align:center" %)
	91	[[image:1.2.png]]
	92
	93	PLC Default Parameters:
	94	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	95	Note:The serial port parameters should be set depending on field requirements
	96
	97	PC and PLC connection:
	98
	99	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	100
	101	(% style="text-align:center" %)
	102	[[image:1.5.1.png]]
	103
	104	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	105
	106	(% style="text-align:center" %)
	107	[[image:1.5.2.png]]
	108
	109	Cable Wiring
	110
38.1	111	RS422
2.1	112
38.1	113	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	114
38.1	115	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	116
43.1	117	== FX NOPROTOCOL ==
	118
	119	Mitsubishi FX3G-RS232-BD
	120
	121	V-Box Settings
	122
	123	\|=Item\|=Settings\|=Note
	124	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	125	\|Connection\|RS232\|
	126	\|Baud rate\|9600\|
	127	\|Data bit\|7\|
	128	\|Parity\|EVEN\|
	129	\|Stop bit\|1\|
	130	\|PLC station No.\|0\|
	131
	132	(% style="text-align:center" %)
	133	[[image:三菱 FN盒子通讯配置.png]]
	134
	135	Address List
	136
	137	\|=Type\|=Device registers\|=HMI registers\|=Format\|=Range\|=Note
	138	\|(% rowspan="8" %)Bit\|X\|X\|X o\|0~~303237\|
	139	\|Y\|Y\|Y o\|0~~303237\|
	140	\|M\|M\|M d\|0~~99999\|
	141	\|T\|T\|T d\|0~~99999\|
	142	\|C\|C\|C d\|0~~99999\|
	143	\|S\|S\|S d\|0~~99999\|
	144	\|SM\|SM\|SM d\|8000~~9999\|
	145	\|Lamp\|Lamp\|Lamp d\|0~~0\|
	146	\|(% rowspan="8" %)Word\|X\|X\|X o\|0~~303237\|
	147	\|Y\|Y\|Y o\|0~~303237\|
	148	\|M\|M\|M d\|0~~99999\|
	149	\|T\|T\|T d\|0~~99999\|
	150	\|C\|C\|C d\|0~~199\|
	151	\|D\|D\|D d\|0~~7999\|
	152	\|S\|S\|S d\|0~~99999\|
	153	\|SD\|SD\|SD d\|8000~~9999\|
	154
	155	Configure the communication protocol
	156
41.1	157	== FX3U Ethernet ==
2.1	158
	159	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	160
41.1	161	V-BOX Settings
2.1	162
	163	\|Items\|Settings\|Note
	164	\|Protocol\|Mitsubishi FX3U\|
	165	\|Connection\|Ethernet\|
	166	\|Port No.\|5009\|Must be the same as the PLC setting
	167	\|PLC station No.\|0\|
	168
41.1	169	Address List
2.1	170
	171	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	172	\|(% rowspan="7" %)Bit\|X\|X\|X OOO\|0~~377\|
	173	\|Y\|Y\|Y OOO\|0~~377\|
	174	\|M\|M\|M DDDD\|0~~7679\|
	175	\|SM\|SM\|SM DDDD\|8000~~8511\|
	176	\|S\|S\|S DDDD\|0~~4095\|
	177	\|TS\|TS\|TS DDD\|0~~511\|
	178	\|CS\|CS\|CS DDD\|0~~255\|
	179	\|(% rowspan="5" %)Word\|CN\|CN\|CN DDD\|0~~199\|
	180	\|TN\|TN\|TN DDD\|0~~511\|
	181	\|D\|D\|D DDDD\|0~~7999\|
	182	\|SD\|SD\|SD DDDD\|8000~~8511\|
	183	\|R\|R\|R DDDDD\|0~~32767\|
	184
41.1	185	Ethernet Module Settings
2.1	186
	187	FX3U-ENET-L module configuration
	188	Set up the FX3U-ENET-L Ethernet module settings as follows.
	189	Select the module location, which in this document is Module 0.
	190
41.1	191	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	192
	193	Select "Operational setting" to enter the following screen.
	194
	195	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	196
41.1	197	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dfbfdd586c855c47.png\|\|alt="image-20221116105947-1.png" height="573" width="706"]]
2.1	198
	199	Select "Open setting" to enter the setting interface, the settings are as follows.
	200
	201	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	202
	203	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	204
41.1	205	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	206
	207	Click on "transter setup" - "PC side I/F setting", see the following figure.
	208
	209	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	210
	211	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	212
41.1	213	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d6fd9ce3b96f99e2.png\|\|alt="image-20221116110832-2.png" height="423" width="708"]]
2.1	214
	215	Read and write data from the Ethernet module
	216
41.1	217	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png\|\|alt="image-20221116110907-3.png" height="549" width="706"]]
2.1	218
	219	Set "Transter setup" to COM communication, and read or write operation as shown below
	220
41.1	221	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png\|\|alt="image-20221116110917-4.png" height="549" width="706"]]
2.1	222
41.1	223	PLC Settings (GX Works 2)
2.1	224
	225	Create a blank FX5U project
	226
	227	Find Current Connection in the navigation
	228
41.1	229	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	230
	231	Select Connection Channel List
	232
	233	Select Ethernet board communication
	234
41.1	235	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	236
	237	Select Ethernet Module
	238	Set the IP address of the PLC
	239
41.1	240	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	241
	242	Read or write PLC data, in this document is read
	243
	244	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	245
41.1	246	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	247
41.1	248	Configure the communication protocol
2.1	249
41.1	250	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b2cdc33b6eb92b67.png\|\|alt="image-20221119101946-2.png" height="395" width="695"]]
2.1	251
	252	== {{id name="HFX5USerial"/}}FX5U Serial ==
	253
	254	Mitsubishi FX5U series PLC
	255
	256	1）V-BOX Settings
	257
	258	\|Item\|Settings\|Note
	259	\|Protocol\|Mitsubishi FX5U\|
	260	\|Connection\|RS422/RS485\|
	261	\|Baud rate\|9600\|
	262	\|Data bit\|7\|
	263	\|Parity\|Odd\|
	264	\|Stop bit\|1\|
	265	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	266
	267	2）Address List
	268
	269	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	270	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	271	\|Y\|Y\|Y o\|0~~303237\|
	272	\|M\|M\|M d\|0~~99999\|
	273	\|B\|B\|B h\|0~~7FFF\|
	274	\|F\|F\|F d\|0~~32767\|
	275	\|SB\|SB\|SB h\|0~~7FFF\|
	276	\|TS\|TS\|TS d\|0~~1023\|
	277	\|TC\|TC\|TC d\|0~~1023\|
	278	\|STS\|STS\|STS d\|0~~1023\|
	279	\|STC\|STC\|STS d\|0~~1023\|
	280	\|CS\|CS\|CS d\|0~~1023\|
	281	\|CC\|CC\|CC d\|0~~1023\|
	282	\|SM\|SM\|SM d\|0~~9999\|
	283	\|L\|L\|L d\|0~~32767\|
	284	\|S\|S\|S d\|0~~4095\|
	285	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	286	\|TN\|TN\|TN d\|0~~1023\|
	287	\|STN\|STN\|STN d\|0~~1023\|
	288	\|CN\|CN\|CN d\|0~~1023\|
	289	\|R\|R\|R d\|0~~32767\|
	290	\|SW\|SW\|SW h\|0~~7FFF\|
	291	\|Z\|Z\|Z d\|0~~23\|
	292	\|D\|D\|D d\|0~~7999\|
	293	\|SD\|SD\|SD d\|0~~11999\|
	294
	295	3）PLC Settings (GX Works 3)
	296
	297	Create a blank FX5U project
	298
	299	Find the 485 serial port module in the system navigation bar and double click to enter the settings.
	300
	301	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_5c9cb13fac1e6c93.png3Fwidth3D20026height3D46226rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5c9cb13fac1e6c93.png?width=200&height=462&rev=1.1\|\|alt="12.PLC Protocol_html_5c9cb13fac1e6c93.png" height="462" width="200"]]
	302
	303	Select protocol in the setting item, and set parameters.
	304
	305	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_de942589ca070228.png3Fwidth3D60026height3D32426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_de942589ca070228.png?width=600&height=324&rev=1.1\|\|alt="12.PLC Protocol_html_de942589ca070228.png" height="324" width="600"]]
	306
	307	Set station number, and [Message Pattern] (Pattern 1 or Pattern 4)
	308
	309	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_387ec7d00b5feb59.png3Fwidth3D60026height3D32326rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_387ec7d00b5feb59.png?width=600&height=323&rev=1.1\|\|alt="12.PLC Protocol_html_387ec7d00b5feb59.png" height="323" width="600"]]
	310
	311	Click the [Apply] button to finish the setting.
	312
	313	Click download and select the items as below, then click [execute] to download the configuration to PLC.
	314
	315	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_cdef1c5ec8cc2105.png3Fwidth3D60026height3D43426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cdef1c5ec8cc2105.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_cdef1c5ec8cc2105.png" height="434" width="600"]]
	316
	317	As soon as download is completed, connect PLC with serial port, then configure it in the [Specify Connection Destination Connection].
	318
	319	Done.
	320
	321	4）Configure the communication protocol
	322
	323	{{id name="Iimage-20220825104904-1.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dbaddd53e9951a17.png\|\|alt="image-20220825104904-1.png" height="1033" width="1920"]]
	324
	325	5）Cable Wiring
	326
	327	* RS422
	328
	329	{{id name="Iimage-20220825105105-2.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
	330
	331	{{id name="Iimage-20220825105533-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
	332
33.1	333	== FX5U Ethernet ==
2.1	334
	335	Mitsubishi FX5U series PLC
	336
	337	1）V-BOX Settings
	338
	339	\|Items\|Settings\|Note
	340	\|Protocol\|Mitsubishi FX5U\|
	341	\|Connection\|Ethernet\|
	342	\|Port No.\|5002\|Must be the same as the PLC setting
	343	\|PLC station No.\|0\|
	344
	345	2）Address List
	346
	347	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	348	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	349	\|Y\|Y\|Y o\|0~~303237\|
	350	\|M\|M\|M d\|0~~99999\|
	351	\|B\|B\|B h\|0~~7FFF\|
	352	\|F\|F\|F d\|0~~32767\|
	353	\|SB\|SB\|SB h\|0~~7FFF\|
	354	\|TS\|TS\|TS d\|0~~1023\|
	355	\|TC\|TC\|TC d\|0~~1023\|
	356	\|STS\|STS\|STS d\|0~~1023\|
	357	\|STC\|STC\|STS d\|0~~1023\|
	358	\|CS\|CS\|CS d\|0~~1023\|
	359	\|CC\|CC\|CC d\|0~~1023\|
	360	\|SM\|SM\|SM d\|0~~9999\|
	361	\|L\|L\|L d\|0~~32767\|
	362	\|S\|S\|S d\|0~~4095\|
	363	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	364	\|TN\|TN\|TN d\|0~~1023\|
	365	\|STN\|STN\|STN d\|0~~1023\|
	366	\|CN\|CN\|CN d\|0~~1023\|
	367	\|R\|R\|R d\|0~~32767\|
	368	\|SW\|SW\|SW h\|0~~7FFF\|
	369	\|Z\|Z\|Z d\|0~~23\|
	370	\|D\|D\|D d\|0~~7999\|
	371	\|SD\|SD\|SD d\|0~~11999\|
	372
	373	3）PLC Settings (GX Works 3)
	374
	375	Find the [Ethernet port] in the navigation area.
	376
	377	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_8e8f85ace087346c.png3Fwidth3D30026height3D59326rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8e8f85ace087346c.png?width=300&height=593&rev=1.1\|\|alt="12.PLC Protocol_html_8e8f85ace087346c.png" height="593" width="300"]]
	378
	379	Select [Own Node Settings] in the [Setting Item List];
	380
	381	Set [IP Address], [Subnet Mask], [Default Gateway];
	382
	383	Click [Detailed Settings] into [Ethernet Configuration (Built-in Ethernet Port)] windows;
	384
	385	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_5d98495052c8c10e.png3Fwidth3D60026height3D33926rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5d98495052c8c10e.png?width=600&height=339&rev=1.1\|\|alt="12.PLC Protocol_html_5d98495052c8c10e.png" height="339" width="600"]]
	386
	387	Select [SLMP Connection Module] and add into host station as below picture shows;
	388
	389	Set Port number as 5002 (this is necessary settings);
	390
	391	Click [Close with Reflecting the Setting] to save and close window;
	392
	393	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_14b489fdc6c6589d.png3Fwidth3D60026height3D35026rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_14b489fdc6c6589d.png?width=600&height=350&rev=1.1\|\|alt="12.PLC Protocol_html_14b489fdc6c6589d.png" height="350" width="600"]]
	394
	395	Click [Apply] to completed Etherenet settings;
	396
	397	Switch to the [On line data operation] interface as below, check the item and click [Execute] to download.
	398
	399	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_c93025a968a8a9e7.png3Fwidth3D60026height3D43426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_c93025a968a8a9e7.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_c93025a968a8a9e7.png" height="434" width="600"]]
	400
	401	4）Configure the communication protocol
	402
	403	{{id name="Iimage-20220825112403-1.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_caa9bf4d8cc6de0f.png\|\|alt="图片-20220825112403-1.png" height="1033" width="1920"]]
	404
	405	5）Cable Wiring
	406
33.1	407	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	408
	409	== {{id name="HL02Serial"/}}L02 Serial ==
	410
	411	Mitsubishi L02 series CPU built-in serial port.
	412
	413	1）V-BOX Settings
	414
	415	\|Item\|Settings\|Note
	416	\|Protocol\|Mitsubishi L02\|
	417	\|Connection\|RS422\|
	418	\|Baud rate\|115200\|
	419	\|Data bit\|8\|
	420	\|Parity\|Odd\|
	421	\|Stop bit\|1\|
	422	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	423
	424	2）Address List
	425
	426	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	427	\|Bit\|X\|X\|X h\|0~~FFFF\|
	428	\|Bit\|Y\|Y\|Y h\|0~~FFFF\|
	429	\|Bit\|M\|M\|M d\|0~~9999\|
	430	\|Bit\|L\|L\|L d\|0~~9999\|
	431	\|Bit\|F\|F\|F d\|0~~9999\|
	432	\|Bit\|B\|B\|B h\|0~~FFFF\|
	433	\|Bit\|V\|V\|V d\|0~~2047\|
	434	\|Bit\|TC\|TC\|TC d\|0~~9999\|
	435	\|Bit\|SS\|SS\|SS d\|0~~9999\|
	436	\|Bit\|SC\|SC\|SC d\|0~~9999\|
	437	\|Bit\|CS\|CS\|CS d\|0~~9999\|
	438	\|Bit\|CC\|CC\|CC d\|0~~9999\|
	439	\|Bit\|SB\|SB\|SB h\|0~~FFFF\|
	440	\|Bit\|SM\|SM\|SM d\|0~~2047\|
	441	\|Bit\|STS\|STS\|STS d\|0~~1023\|
	442	\|Bit\|S\|S\|S d\|0~~9999\|
	443	\|Bit\|DX\|DX\|DX h\|0~~FFFF\|
	444	\|Bit\|DY\|DY\|DY h\|0~~FFFF\|
	445	\|Bit\|TS\|TS\|TS d\|0~~9999\|
	446	\|Bit\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	447	\|Word\|W\|W\|W h\|0~~FFFF\|
	448	\|Word\|TN\|TN\|TN d\|0~~99999\|
	449	\|Word\|SN\|SN\|SN d\|0~~99999\|
	450	\|Word\|CN\|CN\|CN d\|0~~99999\|
	451	\|Word\|R\|R\|R d\|0~~99999\|
	452	\|Word\|SW\|SW\|SW h\|0~~FFFF\|
	453	\|Word\|Z\|Z\|Z d\|0~~99999\|
	454	\|Word\|ZR\|ZR\|ZR h\|0~~FFFF\|
	455	\|Word\|D\|D\|D d\|0~~99999\|
	456
	457	3）Communication Settings
	458
	459	{{id name="Iimage-20220825160648-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_cfed67f2ecb4ccec.png\|\|alt="image-20220825160648-3.png" height="1009" width="1920"]]
	460
	461	4）Cable Wiring
	462
	463	* RS422
	464
	465	{{id name="Iimage-20220825161612-8.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
	466
	467	{{id name="Iimage-20220825160820-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
	468
	469	== {{id name="HL02Ethernet"/}}L02 Ethernet ==
	470
	471	Mitsubishi L series CPU built-in Ethernet port.
	472
	473	1）V-BOX Settings
	474
	475	\|Items\|Settings\|Note
	476	\|Protocol\|MIT L02 CPU MELSEC\|
	477	\|Connection\|Ethernet\|
	478	\|Port No.\|1025\|Must be the same as the PLC setting
	479	\|PLC station No.\|0\|Must be the same as the PLC setting
	480
	481	2）Address List
	482
	483	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	484	\|Bit\|X\|X\|X h\|0~~FFFF\|
	485	\|Bit\|Y\|Y\|Y h\|0~~FFFF\|
	486	\|Bit\|M\|M\|M d\|0~~9999\|
	487	\|Bit\|L\|L\|L d\|0~~9999\|
	488	\|Bit\|F\|F\|F d\|0~~9999\|
	489	\|Bit\|B\|B\|B h\|0~~FFFF\|
	490	\|Bit\|V\|V\|V d\|0~~2047\|
	491	\|Bit\|TC\|TC\|TC d\|0~~9999\|
	492	\|Bit\|SS\|SS\|SS d\|0~~9999\|
	493	\|Bit\|SC\|SC\|SC d\|0~~9999\|
	494	\|Bit\|CS\|CS\|CS d\|0~~9999\|
	495	\|Bit\|CC\|CC\|CC d\|0~~9999\|
	496	\|Bit\|SB\|SB\|SB h\|0~~FFFF\|
	497	\|Bit\|SM\|SM\|SM d\|0~~2047\|
	498	\|Bit\|STS\|STS\|STS d\|0~~1023\|
	499	\|Bit\|S\|S\|S d\|0~~9999\|
	500	\|Bit\|DX\|DX\|DX h\|0~~FFFF\|
	501	\|Bit\|DY\|DY\|DY h\|0~~FFFF\|
	502	\|Bit\|TS\|TS\|TS d\|0~~9999\|
	503	\|Bit\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	504	\|Word\|W\|W\|W h\|0~~FFFF\|
	505	\|Word\|TN\|TN\|TN d\|0~~99999\|
	506	\|Word\|SN\|SN\|SN d\|0~~99999\|
	507	\|Word\|CN\|CN\|CN d\|0~~99999\|
	508	\|Word\|R\|R\|R d\|0~~99999\|
	509	\|Word\|SW\|SW\|SW h\|0~~FFFF\|
	510	\|Word\|Z\|Z\|Z d\|0~~99999\|
	511	\|Word\|ZR\|ZR\|ZR h\|0~~FFFF\|
	512	\|Word\|D\|D\|D d\|0~~99999\|
	513
	514	3）PLC Settings (GX Works2 )
	515
	516	Create a project
	517
	518	Set PLC IP, subnet mask and gateway;
	519
	520	Select [Binary Code] as communication data code;
	521
	522	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_776e17505f3fc6c0.png3Fwidth3D60026height3D52426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
	523
	524	Set PLC port number, for example 1025
	525
	526	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_8d0d1a22d388f70b.png3Fwidth3D60026height3D52426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
	527
	528	Save settings;
	529
	530	Download project into PLC device;
	531
	532	Restart PLC device;
	533
	534	4）Configure the communication protocol
	535
	536	{{id name="Iimage-20220825142659-1.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_fafc9b29e20178c0.png\|\|alt="image-20220825142659-1.png" height="1010" width="1920"]]
	537
	538	5）Cable Wiring
	539
	540	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_2297240b57346b2a.png3Fwidth3D40126height3D17026rev3D1.1-1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
	541
	542	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	543
	544	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	545
	546	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	547
32.1	548	== QJ71E71 Ethernet ==
2.1	549
	550	Mitsubishi QJ71E71 Ethernet communication module;
	551
	552	1）V-BOX Settings
	553
	554	\|Items\|Settings\|Note
	555	\|Protocol\|MIT QJ71E71 MELSEC\|
	556	\|Connection\|Ethernet\|
	557	\|Port No.\|1025\|Must be the same as the PLC setting
	558	\|PLC station No.\|0\|Must be the same as the PLC setting
	559
	560	2）Address List
	561
	562	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	563	\|(% rowspan="18" %)Bit\|X\|X\|X h\|0~~1FFF\|
	564	\|Y\|Y\|Y h\|0~~1FFF\|
	565	\|M\|M\|M d\|0~~99999\|
	566	\|L\|L\|L d\|0~~8191\|
	567	\|F\|F\|F d\|0~~2047\|
	568	\|B\|B\|B h\|0~~1FFF\|
	569	\|V\|V\|V d\|0~~2047\|
	570	\|TS\|TS\|TS d\|0~~2047\|
	571	\|TC\|TC\|TC d\|0~~2047\|
	572	\|SS\|SS\|SS d\|0~~2047\|
	573	\|SC\|SC\|SC d\|0~~2047\|
	574	\|CS\|CS\|CS d\|0~~1023\|
	575	\|CC\|CC\|CC d\|0~~1023\|
	576	\|SB\|SB\|SB h\|0~~7FF\|
	577	\|S\|S\|S d\|0~~8191\|
	578	\|DX\|DX\|DX h\|0~~1FFF\|
	579	\|DY\|DY\|DY h\|0~~1FFF\|
	580	\|SM\|SM\|SM d\|8000~~9999\|
	581	\|(% rowspan="10" %)Word\|SD\|SD\|SD d\|0~~2047\|
	582	\|D\|D\|D d\|0~~12287\|
	583	\|W\|W\|W h\|0~~1FFF\|
	584	\|TN\|TN\|TN d\|0~~2047\|
	585	\|SN\|SN\|SN d\|0~~2047\|
	586	\|CN\|CN\|CN d\|0~~1023\|
	587	\|R\|R\|R d\|0~~32767\|
	588	\|SW\|SW\|SW h\|0~~7FF\|
	589	\|Z\|Z\|Z d\|0~~15\|
	590	\|ZR\|ZR\|ZR h\|0~~FE7FF\|
	591
	592	3）PLC Settings(GX Works2)
	593
	594	* Click [Ethernet/CC IE/MELSECNET];
	595	* Please select [Ethernet] as network type;
	596	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	597	* Select [Online] as Mode;
	598	* {{id name="Iimage-20221119171343-2.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
	599	* Click [Operation setting] to set IP;
	600	* Select [Binary Code] as [Communication Data Code];
	601	* {{id name="Iimage-20221119171436-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
	602	* Click [Open setting]
	603	* Set protocol: TCP;
	604	* Set [unpassive] in [Open system];
	605	* Set [receive] in [Fixed buffer];
	606	* Set [procedure Exist] in [Fixed buffer communication];
	607	* Disable [Pairing open];
	608	* Set [No confirm] in [Existence confirmation];
	609	* Host station port number: 5009;
	610	* Save settings;
	611	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	612	* Download project into PLC and restart it
	613
	614	4）Configure the communication protocol
	615
	616	{{id name="Iimage-20221119171832-5.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50990385ef491b9e.png\|\|alt="image-20221119171832-5.png" height="354" width="625"]]
	617
	618	5）Cable Wiring
	619
34.1	620	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents