Wiki source code of Mitsubishi

Version 44.1 by Theodore Xu on 2023/09/15 10:19

version	line-number	content
39.1	1	== FX1S,1N,2N Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX1S, FX1N, FX2N series
	4
37.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX1S/FX1N/FX2N\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
37.1	16	Address List
2.1	17
37.1	18	\|Type\|Device registers\|V-Box registers\|Format\|Range\|Note
2.1	19	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	20	\|Y\|Y\|Y o\|0~~303237\|
	21	\|M\|M\|M d\|0~~99999\|
	22	\|T\|T\|T d\|0~~99999\|
	23	\|C\|C\|C d\|0~~99999\|
	24	\|S\|S\|S d\|0~~99999\|
	25	\|SM\|SM\|SM d\|8000~~9999\|
	26	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	27	\|Y\|Y\|Y o\|0~~303237\|
	28	\|M\|M\|M d\|0~~99999\|
	29	\|T\|T\|T d\|0~~99999\|
	30	\|C\|C\|C d\|0~~199\|
	31	\|D\|D\|D d\|0~~7999\|
	32	\|S\|S\|S d\|0~~99999\|
	33	\|SD\|SD\|SD d\|8000~~9999\|
	34
37.1	35	Configure the communication protocol
2.1	36
	37	{{id name="Iimage-20220825102844-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dc262f14b14cf564.png\|\|alt="image-20220825102844-3.png" height="1011" width="1920"]]
	38
37.1	39	Cable Wiring
2.1	40
37.1	41	RS422
2.1	42
37.1	43	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_9294a40c62eb99be.png\|\|alt="image-20220825103350-4.png" height="284" width="723"]]
2.1	44
35.1	45	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	46
40.1	47	== FX3U,3G,3GA Serial ==
2.1	48
	49	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	50
38.1	51	V-BOX Settings
2.1	52
	53	\|Item\|Settings\|Note
	54	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	55	\|Connection\|RS422/RS485/RS232\|
	56	\|Baud rate\|9600~~115200\|
	57	\|Data bit\|7/8\|
	58	\|Parity\|EVEN/Odd/None\|
	59	\|Stop bit\|1/2\|
	60	\|PLC station No.\|1~~255\|
	61
38.1	62	Address List
2.1	63
	64	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	65	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	66	\|Y\|Y\|Y o\|0~~303237\|
	67	\|M\|M\|M d\|0~~99999\|
	68	\|T\|T\|T d\|0~~99999\|
	69	\|C\|C\|C d\|0~~99999\|
	70	\|S\|S\|S d\|0~~99999\|
	71	\|SM\|SM\|SM d\|8000~~9999\|
	72	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	73	\|Y\|Y\|Y o\|0~~303237\|
	74	\|M\|M\|M d\|0~~99999\|
	75	\|T\|T\|T d\|0~~99999\|
	76	\|C\|C\|C d\|0~~199\|
	77	\|D\|D\|D d\|0~~7999\|
	78	\|S\|S\|S d\|0~~99999\|
	79	\|SD\|SD\|SD d\|8000~~9999\|
	80
38.1	81	Configure the communication protocol
2.1	82
38.1	83	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_4d2a4921240d23c6.png\|\|alt="image-20220825102649-2.png" height="1009" width="1920"]]
2.1	84
42.1	85	PLC Setting
2.1	86
42.1	87	Open GX Works2, create a new PLC project or open the project that has been created.
	88	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	89
	90	(% style="text-align:center" %)
	91	[[image:1.2.png]]
	92
	93	PLC Default Parameters:
	94	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	95	Note:The serial port parameters should be set depending on field requirements
	96
	97	PC and PLC connection:
	98
	99	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	100
	101	(% style="text-align:center" %)
	102	[[image:1.5.1.png]]
	103
	104	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	105
	106	(% style="text-align:center" %)
	107	[[image:1.5.2.png]]
	108
	109	Cable Wiring
	110
38.1	111	RS422
2.1	112
38.1	113	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	114
38.1	115	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	116
43.1	117	== FX NOPROTOCOL ==
	118
	119	Mitsubishi FX3G-RS232-BD
	120
	121	V-Box Settings
	122
	123	\|=Item\|=Settings\|=Note
	124	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	125	\|Connection\|RS232\|
	126	\|Baud rate\|9600\|
	127	\|Data bit\|7\|
	128	\|Parity\|EVEN\|
	129	\|Stop bit\|1\|
	130	\|PLC station No.\|0\|
	131
	132	(% style="text-align:center" %)
	133	[[image:三菱 FN盒子通讯配置.png]]
	134
	135	Address List
	136
	137	\|=Type\|=Device registers\|=HMI registers\|=Format\|=Range\|=Note
	138	\|(% rowspan="8" %)Bit\|X\|X\|X o\|0~~303237\|
	139	\|Y\|Y\|Y o\|0~~303237\|
	140	\|M\|M\|M d\|0~~99999\|
	141	\|T\|T\|T d\|0~~99999\|
	142	\|C\|C\|C d\|0~~99999\|
	143	\|S\|S\|S d\|0~~99999\|
	144	\|SM\|SM\|SM d\|8000~~9999\|
	145	\|Lamp\|Lamp\|Lamp d\|0~~0\|
	146	\|(% rowspan="8" %)Word\|X\|X\|X o\|0~~303237\|
	147	\|Y\|Y\|Y o\|0~~303237\|
	148	\|M\|M\|M d\|0~~99999\|
	149	\|T\|T\|T d\|0~~99999\|
	150	\|C\|C\|C d\|0~~199\|
	151	\|D\|D\|D d\|0~~7999\|
	152	\|S\|S\|S d\|0~~99999\|
	153	\|SD\|SD\|SD d\|8000~~9999\|
	154
44.1	155	Wiring
43.1	156
44.1	157	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	158
41.1	159	== FX3U Ethernet ==
2.1	160
	161	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	162
41.1	163	V-BOX Settings
2.1	164
	165	\|Items\|Settings\|Note
	166	\|Protocol\|Mitsubishi FX3U\|
	167	\|Connection\|Ethernet\|
	168	\|Port No.\|5009\|Must be the same as the PLC setting
	169	\|PLC station No.\|0\|
	170
41.1	171	Address List
2.1	172
	173	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	174	\|(% rowspan="7" %)Bit\|X\|X\|X OOO\|0~~377\|
	175	\|Y\|Y\|Y OOO\|0~~377\|
	176	\|M\|M\|M DDDD\|0~~7679\|
	177	\|SM\|SM\|SM DDDD\|8000~~8511\|
	178	\|S\|S\|S DDDD\|0~~4095\|
	179	\|TS\|TS\|TS DDD\|0~~511\|
	180	\|CS\|CS\|CS DDD\|0~~255\|
	181	\|(% rowspan="5" %)Word\|CN\|CN\|CN DDD\|0~~199\|
	182	\|TN\|TN\|TN DDD\|0~~511\|
	183	\|D\|D\|D DDDD\|0~~7999\|
	184	\|SD\|SD\|SD DDDD\|8000~~8511\|
	185	\|R\|R\|R DDDDD\|0~~32767\|
	186
41.1	187	Ethernet Module Settings
2.1	188
	189	FX3U-ENET-L module configuration
	190	Set up the FX3U-ENET-L Ethernet module settings as follows.
	191	Select the module location, which in this document is Module 0.
	192
41.1	193	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	194
	195	Select "Operational setting" to enter the following screen.
	196
	197	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	198
41.1	199	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dfbfdd586c855c47.png\|\|alt="image-20221116105947-1.png" height="573" width="706"]]
2.1	200
	201	Select "Open setting" to enter the setting interface, the settings are as follows.
	202
	203	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	204
	205	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	206
41.1	207	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	208
	209	Click on "transter setup" - "PC side I/F setting", see the following figure.
	210
	211	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	212
	213	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	214
41.1	215	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d6fd9ce3b96f99e2.png\|\|alt="image-20221116110832-2.png" height="423" width="708"]]
2.1	216
	217	Read and write data from the Ethernet module
	218
41.1	219	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png\|\|alt="image-20221116110907-3.png" height="549" width="706"]]
2.1	220
	221	Set "Transter setup" to COM communication, and read or write operation as shown below
	222
41.1	223	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png\|\|alt="image-20221116110917-4.png" height="549" width="706"]]
2.1	224
41.1	225	PLC Settings (GX Works 2)
2.1	226
	227	Create a blank FX5U project
	228
	229	Find Current Connection in the navigation
	230
41.1	231	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	232
	233	Select Connection Channel List
	234
	235	Select Ethernet board communication
	236
41.1	237	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	238
	239	Select Ethernet Module
	240	Set the IP address of the PLC
	241
41.1	242	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	243
	244	Read or write PLC data, in this document is read
	245
	246	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	247
41.1	248	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	249
41.1	250	Configure the communication protocol
2.1	251
41.1	252	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b2cdc33b6eb92b67.png\|\|alt="image-20221119101946-2.png" height="395" width="695"]]
2.1	253
	254	== {{id name="HFX5USerial"/}}FX5U Serial ==
	255
	256	Mitsubishi FX5U series PLC
	257
	258	1）V-BOX Settings
	259
	260	\|Item\|Settings\|Note
	261	\|Protocol\|Mitsubishi FX5U\|
	262	\|Connection\|RS422/RS485\|
	263	\|Baud rate\|9600\|
	264	\|Data bit\|7\|
	265	\|Parity\|Odd\|
	266	\|Stop bit\|1\|
	267	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	268
	269	2）Address List
	270
	271	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	272	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	273	\|Y\|Y\|Y o\|0~~303237\|
	274	\|M\|M\|M d\|0~~99999\|
	275	\|B\|B\|B h\|0~~7FFF\|
	276	\|F\|F\|F d\|0~~32767\|
	277	\|SB\|SB\|SB h\|0~~7FFF\|
	278	\|TS\|TS\|TS d\|0~~1023\|
	279	\|TC\|TC\|TC d\|0~~1023\|
	280	\|STS\|STS\|STS d\|0~~1023\|
	281	\|STC\|STC\|STS d\|0~~1023\|
	282	\|CS\|CS\|CS d\|0~~1023\|
	283	\|CC\|CC\|CC d\|0~~1023\|
	284	\|SM\|SM\|SM d\|0~~9999\|
	285	\|L\|L\|L d\|0~~32767\|
	286	\|S\|S\|S d\|0~~4095\|
	287	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	288	\|TN\|TN\|TN d\|0~~1023\|
	289	\|STN\|STN\|STN d\|0~~1023\|
	290	\|CN\|CN\|CN d\|0~~1023\|
	291	\|R\|R\|R d\|0~~32767\|
	292	\|SW\|SW\|SW h\|0~~7FFF\|
	293	\|Z\|Z\|Z d\|0~~23\|
	294	\|D\|D\|D d\|0~~7999\|
	295	\|SD\|SD\|SD d\|0~~11999\|
	296
	297	3）PLC Settings (GX Works 3)
	298
	299	Create a blank FX5U project
	300
	301	Find the 485 serial port module in the system navigation bar and double click to enter the settings.
	302
	303	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_5c9cb13fac1e6c93.png3Fwidth3D20026height3D46226rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5c9cb13fac1e6c93.png?width=200&height=462&rev=1.1\|\|alt="12.PLC Protocol_html_5c9cb13fac1e6c93.png" height="462" width="200"]]
	304
	305	Select protocol in the setting item, and set parameters.
	306
	307	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_de942589ca070228.png3Fwidth3D60026height3D32426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_de942589ca070228.png?width=600&height=324&rev=1.1\|\|alt="12.PLC Protocol_html_de942589ca070228.png" height="324" width="600"]]
	308
	309	Set station number, and [Message Pattern] (Pattern 1 or Pattern 4)
	310
	311	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_387ec7d00b5feb59.png3Fwidth3D60026height3D32326rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_387ec7d00b5feb59.png?width=600&height=323&rev=1.1\|\|alt="12.PLC Protocol_html_387ec7d00b5feb59.png" height="323" width="600"]]
	312
	313	Click the [Apply] button to finish the setting.
	314
	315	Click download and select the items as below, then click [execute] to download the configuration to PLC.
	316
	317	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_cdef1c5ec8cc2105.png3Fwidth3D60026height3D43426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cdef1c5ec8cc2105.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_cdef1c5ec8cc2105.png" height="434" width="600"]]
	318
	319	As soon as download is completed, connect PLC with serial port, then configure it in the [Specify Connection Destination Connection].
	320
	321	Done.
	322
	323	4）Configure the communication protocol
	324
	325	{{id name="Iimage-20220825104904-1.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dbaddd53e9951a17.png\|\|alt="image-20220825104904-1.png" height="1033" width="1920"]]
	326
	327	5）Cable Wiring
	328
	329	* RS422
	330
	331	{{id name="Iimage-20220825105105-2.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
	332
	333	{{id name="Iimage-20220825105533-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
	334
33.1	335	== FX5U Ethernet ==
2.1	336
	337	Mitsubishi FX5U series PLC
	338
	339	1）V-BOX Settings
	340
	341	\|Items\|Settings\|Note
	342	\|Protocol\|Mitsubishi FX5U\|
	343	\|Connection\|Ethernet\|
	344	\|Port No.\|5002\|Must be the same as the PLC setting
	345	\|PLC station No.\|0\|
	346
	347	2）Address List
	348
	349	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	350	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	351	\|Y\|Y\|Y o\|0~~303237\|
	352	\|M\|M\|M d\|0~~99999\|
	353	\|B\|B\|B h\|0~~7FFF\|
	354	\|F\|F\|F d\|0~~32767\|
	355	\|SB\|SB\|SB h\|0~~7FFF\|
	356	\|TS\|TS\|TS d\|0~~1023\|
	357	\|TC\|TC\|TC d\|0~~1023\|
	358	\|STS\|STS\|STS d\|0~~1023\|
	359	\|STC\|STC\|STS d\|0~~1023\|
	360	\|CS\|CS\|CS d\|0~~1023\|
	361	\|CC\|CC\|CC d\|0~~1023\|
	362	\|SM\|SM\|SM d\|0~~9999\|
	363	\|L\|L\|L d\|0~~32767\|
	364	\|S\|S\|S d\|0~~4095\|
	365	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	366	\|TN\|TN\|TN d\|0~~1023\|
	367	\|STN\|STN\|STN d\|0~~1023\|
	368	\|CN\|CN\|CN d\|0~~1023\|
	369	\|R\|R\|R d\|0~~32767\|
	370	\|SW\|SW\|SW h\|0~~7FFF\|
	371	\|Z\|Z\|Z d\|0~~23\|
	372	\|D\|D\|D d\|0~~7999\|
	373	\|SD\|SD\|SD d\|0~~11999\|
	374
	375	3）PLC Settings (GX Works 3)
	376
	377	Find the [Ethernet port] in the navigation area.
	378
	379	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_8e8f85ace087346c.png3Fwidth3D30026height3D59326rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8e8f85ace087346c.png?width=300&height=593&rev=1.1\|\|alt="12.PLC Protocol_html_8e8f85ace087346c.png" height="593" width="300"]]
	380
	381	Select [Own Node Settings] in the [Setting Item List];
	382
	383	Set [IP Address], [Subnet Mask], [Default Gateway];
	384
	385	Click [Detailed Settings] into [Ethernet Configuration (Built-in Ethernet Port)] windows;
	386
	387	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_5d98495052c8c10e.png3Fwidth3D60026height3D33926rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5d98495052c8c10e.png?width=600&height=339&rev=1.1\|\|alt="12.PLC Protocol_html_5d98495052c8c10e.png" height="339" width="600"]]
	388
	389	Select [SLMP Connection Module] and add into host station as below picture shows;
	390
	391	Set Port number as 5002 (this is necessary settings);
	392
	393	Click [Close with Reflecting the Setting] to save and close window;
	394
	395	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_14b489fdc6c6589d.png3Fwidth3D60026height3D35026rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_14b489fdc6c6589d.png?width=600&height=350&rev=1.1\|\|alt="12.PLC Protocol_html_14b489fdc6c6589d.png" height="350" width="600"]]
	396
	397	Click [Apply] to completed Etherenet settings;
	398
	399	Switch to the [On line data operation] interface as below, check the item and click [Execute] to download.
	400
	401	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_c93025a968a8a9e7.png3Fwidth3D60026height3D43426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_c93025a968a8a9e7.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_c93025a968a8a9e7.png" height="434" width="600"]]
	402
	403	4）Configure the communication protocol
	404
	405	{{id name="Iimage-20220825112403-1.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_caa9bf4d8cc6de0f.png\|\|alt="图片-20220825112403-1.png" height="1033" width="1920"]]
	406
	407	5）Cable Wiring
	408
33.1	409	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	410
	411	== {{id name="HL02Serial"/}}L02 Serial ==
	412
	413	Mitsubishi L02 series CPU built-in serial port.
	414
	415	1）V-BOX Settings
	416
	417	\|Item\|Settings\|Note
	418	\|Protocol\|Mitsubishi L02\|
	419	\|Connection\|RS422\|
	420	\|Baud rate\|115200\|
	421	\|Data bit\|8\|
	422	\|Parity\|Odd\|
	423	\|Stop bit\|1\|
	424	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	425
	426	2）Address List
	427
	428	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	429	\|Bit\|X\|X\|X h\|0~~FFFF\|
	430	\|Bit\|Y\|Y\|Y h\|0~~FFFF\|
	431	\|Bit\|M\|M\|M d\|0~~9999\|
	432	\|Bit\|L\|L\|L d\|0~~9999\|
	433	\|Bit\|F\|F\|F d\|0~~9999\|
	434	\|Bit\|B\|B\|B h\|0~~FFFF\|
	435	\|Bit\|V\|V\|V d\|0~~2047\|
	436	\|Bit\|TC\|TC\|TC d\|0~~9999\|
	437	\|Bit\|SS\|SS\|SS d\|0~~9999\|
	438	\|Bit\|SC\|SC\|SC d\|0~~9999\|
	439	\|Bit\|CS\|CS\|CS d\|0~~9999\|
	440	\|Bit\|CC\|CC\|CC d\|0~~9999\|
	441	\|Bit\|SB\|SB\|SB h\|0~~FFFF\|
	442	\|Bit\|SM\|SM\|SM d\|0~~2047\|
	443	\|Bit\|STS\|STS\|STS d\|0~~1023\|
	444	\|Bit\|S\|S\|S d\|0~~9999\|
	445	\|Bit\|DX\|DX\|DX h\|0~~FFFF\|
	446	\|Bit\|DY\|DY\|DY h\|0~~FFFF\|
	447	\|Bit\|TS\|TS\|TS d\|0~~9999\|
	448	\|Bit\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	449	\|Word\|W\|W\|W h\|0~~FFFF\|
	450	\|Word\|TN\|TN\|TN d\|0~~99999\|
	451	\|Word\|SN\|SN\|SN d\|0~~99999\|
	452	\|Word\|CN\|CN\|CN d\|0~~99999\|
	453	\|Word\|R\|R\|R d\|0~~99999\|
	454	\|Word\|SW\|SW\|SW h\|0~~FFFF\|
	455	\|Word\|Z\|Z\|Z d\|0~~99999\|
	456	\|Word\|ZR\|ZR\|ZR h\|0~~FFFF\|
	457	\|Word\|D\|D\|D d\|0~~99999\|
	458
	459	3）Communication Settings
	460
	461	{{id name="Iimage-20220825160648-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_cfed67f2ecb4ccec.png\|\|alt="image-20220825160648-3.png" height="1009" width="1920"]]
	462
	463	4）Cable Wiring
	464
	465	* RS422
	466
	467	{{id name="Iimage-20220825161612-8.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
	468
	469	{{id name="Iimage-20220825160820-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
	470
	471	== {{id name="HL02Ethernet"/}}L02 Ethernet ==
	472
	473	Mitsubishi L series CPU built-in Ethernet port.
	474
	475	1）V-BOX Settings
	476
	477	\|Items\|Settings\|Note
	478	\|Protocol\|MIT L02 CPU MELSEC\|
	479	\|Connection\|Ethernet\|
	480	\|Port No.\|1025\|Must be the same as the PLC setting
	481	\|PLC station No.\|0\|Must be the same as the PLC setting
	482
	483	2）Address List
	484
	485	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	486	\|Bit\|X\|X\|X h\|0~~FFFF\|
	487	\|Bit\|Y\|Y\|Y h\|0~~FFFF\|
	488	\|Bit\|M\|M\|M d\|0~~9999\|
	489	\|Bit\|L\|L\|L d\|0~~9999\|
	490	\|Bit\|F\|F\|F d\|0~~9999\|
	491	\|Bit\|B\|B\|B h\|0~~FFFF\|
	492	\|Bit\|V\|V\|V d\|0~~2047\|
	493	\|Bit\|TC\|TC\|TC d\|0~~9999\|
	494	\|Bit\|SS\|SS\|SS d\|0~~9999\|
	495	\|Bit\|SC\|SC\|SC d\|0~~9999\|
	496	\|Bit\|CS\|CS\|CS d\|0~~9999\|
	497	\|Bit\|CC\|CC\|CC d\|0~~9999\|
	498	\|Bit\|SB\|SB\|SB h\|0~~FFFF\|
	499	\|Bit\|SM\|SM\|SM d\|0~~2047\|
	500	\|Bit\|STS\|STS\|STS d\|0~~1023\|
	501	\|Bit\|S\|S\|S d\|0~~9999\|
	502	\|Bit\|DX\|DX\|DX h\|0~~FFFF\|
	503	\|Bit\|DY\|DY\|DY h\|0~~FFFF\|
	504	\|Bit\|TS\|TS\|TS d\|0~~9999\|
	505	\|Bit\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	506	\|Word\|W\|W\|W h\|0~~FFFF\|
	507	\|Word\|TN\|TN\|TN d\|0~~99999\|
	508	\|Word\|SN\|SN\|SN d\|0~~99999\|
	509	\|Word\|CN\|CN\|CN d\|0~~99999\|
	510	\|Word\|R\|R\|R d\|0~~99999\|
	511	\|Word\|SW\|SW\|SW h\|0~~FFFF\|
	512	\|Word\|Z\|Z\|Z d\|0~~99999\|
	513	\|Word\|ZR\|ZR\|ZR h\|0~~FFFF\|
	514	\|Word\|D\|D\|D d\|0~~99999\|
	515
	516	3）PLC Settings (GX Works2 )
	517
	518	Create a project
	519
	520	Set PLC IP, subnet mask and gateway;
	521
	522	Select [Binary Code] as communication data code;
	523
	524	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_776e17505f3fc6c0.png3Fwidth3D60026height3D52426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
	525
	526	Set PLC port number, for example 1025
	527
	528	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_8d0d1a22d388f70b.png3Fwidth3D60026height3D52426rev3D1.1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
	529
	530	Save settings;
	531
	532	Download project into PLC device;
	533
	534	Restart PLC device;
	535
	536	4）Configure the communication protocol
	537
	538	{{id name="Iimage-20220825142659-1.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_fafc9b29e20178c0.png\|\|alt="image-20220825142659-1.png" height="1010" width="1920"]]
	539
	540	5）Cable Wiring
	541
	542	{{id name="Ihttps:2F2Fdocs.we-con.com.cn2Fbin2Fdownload2FPIStudio2F12.PLC2520protocols2FWebHome2F12.PLC2520Protocol_html_2297240b57346b2a.png3Fwidth3D40126height3D17026rev3D1.1-1"/}}[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
	543
	544	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	545
	546	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	547
	548	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	549
32.1	550	== QJ71E71 Ethernet ==
2.1	551
	552	Mitsubishi QJ71E71 Ethernet communication module;
	553
	554	1）V-BOX Settings
	555
	556	\|Items\|Settings\|Note
	557	\|Protocol\|MIT QJ71E71 MELSEC\|
	558	\|Connection\|Ethernet\|
	559	\|Port No.\|1025\|Must be the same as the PLC setting
	560	\|PLC station No.\|0\|Must be the same as the PLC setting
	561
	562	2）Address List
	563
	564	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	565	\|(% rowspan="18" %)Bit\|X\|X\|X h\|0~~1FFF\|
	566	\|Y\|Y\|Y h\|0~~1FFF\|
	567	\|M\|M\|M d\|0~~99999\|
	568	\|L\|L\|L d\|0~~8191\|
	569	\|F\|F\|F d\|0~~2047\|
	570	\|B\|B\|B h\|0~~1FFF\|
	571	\|V\|V\|V d\|0~~2047\|
	572	\|TS\|TS\|TS d\|0~~2047\|
	573	\|TC\|TC\|TC d\|0~~2047\|
	574	\|SS\|SS\|SS d\|0~~2047\|
	575	\|SC\|SC\|SC d\|0~~2047\|
	576	\|CS\|CS\|CS d\|0~~1023\|
	577	\|CC\|CC\|CC d\|0~~1023\|
	578	\|SB\|SB\|SB h\|0~~7FF\|
	579	\|S\|S\|S d\|0~~8191\|
	580	\|DX\|DX\|DX h\|0~~1FFF\|
	581	\|DY\|DY\|DY h\|0~~1FFF\|
	582	\|SM\|SM\|SM d\|8000~~9999\|
	583	\|(% rowspan="10" %)Word\|SD\|SD\|SD d\|0~~2047\|
	584	\|D\|D\|D d\|0~~12287\|
	585	\|W\|W\|W h\|0~~1FFF\|
	586	\|TN\|TN\|TN d\|0~~2047\|
	587	\|SN\|SN\|SN d\|0~~2047\|
	588	\|CN\|CN\|CN d\|0~~1023\|
	589	\|R\|R\|R d\|0~~32767\|
	590	\|SW\|SW\|SW h\|0~~7FF\|
	591	\|Z\|Z\|Z d\|0~~15\|
	592	\|ZR\|ZR\|ZR h\|0~~FE7FF\|
	593
	594	3）PLC Settings(GX Works2)
	595
	596	* Click [Ethernet/CC IE/MELSECNET];
	597	* Please select [Ethernet] as network type;
	598	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	599	* Select [Online] as Mode;
	600	* {{id name="Iimage-20221119171343-2.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
	601	* Click [Operation setting] to set IP;
	602	* Select [Binary Code] as [Communication Data Code];
	603	* {{id name="Iimage-20221119171436-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
	604	* Click [Open setting]
	605	* Set protocol: TCP;
	606	* Set [unpassive] in [Open system];
	607	* Set [receive] in [Fixed buffer];
	608	* Set [procedure Exist] in [Fixed buffer communication];
	609	* Disable [Pairing open];
	610	* Set [No confirm] in [Existence confirmation];
	611	* Host station port number: 5009;
	612	* Save settings;
	613	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	614	* Download project into PLC and restart it
	615
	616	4）Configure the communication protocol
	617
	618	{{id name="Iimage-20221119171832-5.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50990385ef491b9e.png\|\|alt="image-20221119171832-5.png" height="354" width="625"]]
	619
	620	5）Cable Wiring
	621
34.1	622	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents