Skip to Content

Wiki source code of Mitsubishi

Last modified by Wecon on 2025/09/03 21:04
Show last authors
1 == **FX3U,3G,3GA Serial ** ==
2
3 Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
4
5 **V-BOX Settings**
6
7 |**Item**|**Settings**|**Note**
8 |Protocol|Mitsubishi FX3U/3G/3GA|
9 |Connection|RS422/RS485/RS232|
10 |Baud rate|9600~~115200|
11 |Data bit|7/8|
12 |Parity|EVEN/Odd/None|
13 |Stop bit|1/2|
14 |PLC station No.|1~~255|
15
16 (% style="text-align:center" %)
17 [[image:三菱 FX3U 串口协议配置.png]]
18
19 **Address List**
20
21 |**Type**|**Device registers**|**Format**|**Range**|**Note**
22 |(% rowspan="7" %)Bit|X|X o|0~~303237|
23 |Y|Y o|0~~303237|
24 |M|M d|0~~99999|
25 |T|T d|0~~99999|
26 |C|C d|0~~99999|
27 |S|S d|0~~99999|
28 |SM|SM d|8000~~9999|
29 |(% rowspan="8" %)Word|X|X o|0~~303237|
30 |Y|Y o|0~~303237|
31 |M|M d|0~~99999|
32 |T|T d|0~~99999|
33 |C|C d|0~~199|
34 |D|D d|0~~7999|
35 |S|S d|0~~99999|
36 |SD|SD d|8000~~9999|
37
38 **PLC Setting**
39
40 Open GX Works2, create a new PLC project or open the project that has been created.
41 Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
42
43 (% style="text-align:center" %)
44 [[image:GX2.png]]
45
46 (% style="text-align:center" %)
47 [[image:1.2.png]]
48
49 PLC Default Parameters:
50 [Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
51 Note:The serial port parameters should be set depending on field requirements
52
53 PC and PLC connection:
54
55 [All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
56
57 (% style="text-align:center" %)
58 [[image:1.5.1.png]]
59
60 Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
61
62 (% style="text-align:center" %)
63 [[image:1.5.2.png]]
64
65 [PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
66
67 (% style="text-align:center" %)
68 [[image:FX3U串口下载.png]]
69
70 **Cable Wiring**
71
72 **RS422**
73
74 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png||alt="image-20220825103421-5.png" height="296" width="715"]]
75
76 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png||alt="image-20220825100845-4.png" height="246" width="419"]]
77
78 == **FX NOPROTOCOL** ==
79
80 Mitsubishi FX3G-RS232-BD
81
82 **V-Box Settings**
83
84 |=**Item**|=**Settings**|=**Note**
85 |Protocol|Mitsubishi FX NOPROTOCOL|
86 |Connection|RS232|
87 |Baud rate|9600|
88 |Data bit|7|
89 |Parity|EVEN|
90 |Stop bit|1|
91 |PLC station No.|0|
92
93 (% style="text-align:center" %)
94 [[image:三菱 FN盒子通讯配置.png]]
95
96 **Address List**
97
98 |=**Type**|=**Device registers**|=**Format**|=**Range**|=**Note**
99 |(% rowspan="8" %)Bit|X|X o|0~~303237|
100 |Y|Y o|0~~303237|
101 |M|M d|0~~99999|
102 |T|T d|0~~99999|
103 |C|C d|0~~99999|
104 |S|S d|0~~99999|
105 |SM|SM d|8000~~9999|
106 |Lamp|Lamp d|0~~0|
107 |(% rowspan="8" %)Word|X|X o|0~~303237|
108 |Y|Y o|0~~303237|
109 |M|M d|0~~99999|
110 |T|T d|0~~99999|
111 |C|C d|0~~199|
112 |D|D d|0~~7999|
113 |S|S d|0~~99999|
114 |SD|SD d|8000~~9999|
115
116 **Cable Wiring**
117
118 [[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
119
120 == **FX3U Ethernet ** ==
121
122 Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
123
124 **V-BOX Settings**
125
126 |Items|Settings|Note
127 |Protocol|Mitsubishi FX3U|
128 |Connection|Ethernet|
129 |Port No.|5009|Must be the same as the PLC setting
130 |PLC station No.|0|
131
132 (% style="text-align:center" %)
133 [[image:三菱 FX3U 以太网协议配置.png]]
134
135 **Address List**
136
137 |**Type**|**Device registers**|**Format**|**Range**|**Note**
138 |(% rowspan="7" %)Bit|X|X OOO|0~~377|
139 |Y|Y OOO|0~~377|
140 |M|M DDDD|0~~7679|
141 |SM|SM DDDD|8000~~8511|
142 |S|S DDDD|0~~4095|
143 |TS|TS DDD|0~~511|
144 |CS|CS DDD|0~~255|
145 |(% rowspan="5" %)Word|CN|CN DDD|0~~199|
146 |TN|TN DDD|0~~511|
147 |D|D DDDD|0~~7999|
148 |SD|SD DDDD|8000~~8511|
149 |R|R DDDDD|0~~32767|
150
151 **Ethernet Module Settings**
152
153 FX3U-ENET-L module configuration
154 Set up the FX3U-ENET-L Ethernet module settings as follows.
155 Select the module location, which in this document is Module 0.
156
157 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png||alt="image-20221116105850-1.png" height="573" width="706"]]
158
159 Select "Operational setting" to enter the following screen.
160
161 The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
162
163
164 (% style="text-align:center" %)
165 [[image:Inku25HyY8.png]]
166
167 Select "Open setting" to enter the setting interface, the settings are as follows.
168
169 The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
170
171 Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
172
173 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png||alt="image-20221116110802-1.png" height="549" width="706"]]
174
175 (% class="box infomessage" %)
176 (((
177 Note: If you can't communicate PLC to box normally, changing ''No confirm" to "confirm"
178 )))
179
180 Click on "transter setup" - "PC side I/F setting", see the following figure.
181
182 After setting, the first download must use the programming cable, as shown in the figure; after that, can
183
184 use the IP set in the "Ethernet board" to communicate directly with the network cable.
185
186
187 (% style="text-align:center" %)
188 [[image:WstTyoGrxG.png]]
189
190 (% style="text-align:center" %)
191 [[image:aak9XC8xDH.png]]
192
193
194
195 **PLC Settings (GX Works 2)**
196
197 Create a blank FX5U project
198
199 Find Current Connection in the navigation
200
201 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png||alt="image-20221116111427-1.png" height="421" width="705"]]
202
203 Select Connection Channel List
204
205 Select Ethernet board communication
206
207 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png||alt="image-20221116111451-2.png" height="421" width="705"]]
208
209 Select Ethernet Module
210 Set the IP address of the PLC
211
212 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png||alt="image-20221116111509-3.png" height="666" width="699"]]
213
214 Read or write PLC data, in this document is read
215
216 {{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png||alt="image-20221116111651-4.png" height="416" width="697"]]
217
218 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png||alt="image-20221116111727-5.png" height="416" width="697"]]
219
220 == **FX5U Serial ** ==
221
222 Mitsubishi FX5U series PLC
223
224 **V-BOX Settings**
225
226 |**Item**|**Settings**|**Note**
227 |Protocol|Mitsubishi FX5U|
228 |Connection|RS422/RS485|
229 |Baud rate|9600|
230 |Data bit|7|
231 |Parity|Odd|
232 |Stop bit|1|
233 |PLC station No.|1~~255|Need to be the same as PLC settings
234
235 (% style="text-align:center" %)
236 [[image:三菱 FX5U 串口协议配置.png]]
237
238 **Address List**
239
240 |**Type**|**Device registers**|**Format**|**Range**|**Note**
241 |(% rowspan="15" %)Bit|X|X o|0~~303237|
242 |Y|Y o|0~~303237|
243 |M|M d|0~~99999|
244 |B|B h|0~~7FFF|
245 |F|F d|0~~32767|
246 |SB|SB h|0~~7FFF|
247 |TS|TS d|0~~1023|
248 |TC|TC d|0~~1023|
249 |STS|STS d|0~~1023|
250 |STC|STS d|0~~1023|
251 |CS|CS d|0~~1023|
252 |CC|CC d|0~~1023|
253 |SM|SM d|0~~9999|
254 |L|L d|0~~32767|
255 |S|S d|0~~4095|
256 |(% rowspan="9" %)Word|W|W h|0~~3FF|
257 |TN|TN d|0~~1023|
258 |STN|STN d|0~~1023|
259 |CN|CN d|0~~1023|
260 |R|R d|0~~32767|
261 |SW|SW h|0~~7FFF|
262 |Z|Z d|0~~23|
263 |D|D d|0~~7999|
264 |SD|SD d|0~~11999|
265
266 **PLC Settings **
267
268 Create a blank FX5U project
269
270 Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
271
272 (% style="text-align:center" %)
273 [[image:GX3.png]]
274
275
276 (% style="text-align:center" %)
277 [[image:FX5U 串口选型号.png]]
278
279 PLC Default Parameters: 
280 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
281
282 (% style="text-align:center" %)
283 [[image:FX5U plc串口参数配置.png]]
284
285
286 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
287
288 {{info}}
289 **✎Note:** The serial port parameters should be set depending on field requirements.
290 {{/info}}
291
292 (% style="text-align:center" %)
293 [[image:FX5U plc串口参数.png]]
294
295 **Cable Wiring**
296
297 **RS422**
298
299 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png||alt="image-20220825105105-2.png" height="288" width="711"]]
300
301 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png||alt="image-20220825105533-3.png" height="246" width="420"]]
302
303 == **FX5U Ethernet ** ==
304
305 Mitsubishi FX5U series PLC
306
307 **V-BOX Settings**
308
309 |**Items**|**Settings**|**Note**
310 |Protocol|Mitsubishi FX5U|
311 |Connection|Ethernet|
312 |Port No.|5002|Must be the same as the PLC setting
313 |PLC station No.|0|
314
315 (% style="text-align:center" %)
316 [[image:三菱 FX5U 以太网协议配置.png]]
317
318 **Address List**
319
320 |**Type**|**Device registers**|**Format**|**Range**|**Note**
321 |(% rowspan="15" %)Bit|X|X o|0~~303237|
322 |Y|Y o|0~~303237|
323 |M|M d|0~~99999|
324 |B|B h|0~~7FFF|
325 |F|F d|0~~32767|
326 |SB|SB h|0~~7FFF|
327 |TS|TS d|0~~1023|
328 |TC|TC d|0~~1023|
329 |STS|STS d|0~~1023|
330 |STC|STS d|0~~1023|
331 |CS|CS d|0~~1023|
332 |CC|CC d|0~~1023|
333 |SM|SM d|0~~9999|
334 |L|L d|0~~32767|
335 |S|S d|0~~4095|
336 |(% rowspan="9" %)Word|W|W h|0~~3FF|
337 |TN|TN d|0~~1023|
338 |STN|STN d|0~~1023|
339 |CN|CN d|0~~1023|
340 |R|R d|0~~32767|
341 |SW|SW h|0~~7FFF|
342 |Z|Z d|0~~23|
343 |D|D d|0~~7999|
344 |SD|SD d|0~~11999|
345
346 **PLC Settings **
347
348 Open GX Works3, create a new PLC project or open the project that has been created.
349
350 Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
351
352 (% style="text-align:center" %)
353 [[image:GX3.png]]
354
355 (% style="text-align:center" %)
356 [[image:FX5U 串口选型号.png]]
357
358 PLC Default Parameters: 
359 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
360
361 (% style="text-align:center" %)
362 [[image:FX5U 以太网配置.png]]
363
364 [External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
365
366 (% style="text-align:center" %)
367 [[image:1.3.2.png]]
368
369 PC and PLC connection
370
371 [Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
372
373 (% style="text-align:center" %)
374 [[image:FX5U 以太网连接PLC.png]]
375
376 Downloading PLC project
377 [Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
378
379 (% style="text-align:center" %)
380 [[image:FX5U以太网下载.png]]
381
382 **Cable Wiring**
383
384 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
385
386 == **L02 Serial ** ==
387
388 Mitsubishi L02 series CPU built-in serial port.
389
390 **V-BOX Settings**
391
392 |**Item**|**Settings**|**Note**
393 |Protocol|Mitsubishi L02|
394 |Connection|RS422|
395 |Baud rate|115200|
396 |Data bit|8|
397 |Parity|Odd|
398 |Stop bit|1|
399 |PLC station No.|1~~255|Need to be the same as PLC settings
400
401 (% style="text-align:center" %)
402 [[image:三菱 L02串口协议配置.png]]
403
404 **Address List**
405
406 |**Type**|**Device registers**|**Format**|**Range**|**Note**
407 |(% colspan="1" rowspan="20" %)Bit
408 |X|X h|0~~FFFF|
409 |Y|Y h|0~~FFFF|
410 |M|M d|0~~9999|
411 |L|L d|0~~9999|
412 |F|F d|0~~9999|
413 |B|B h|0~~FFFF|
414 |V|V d|0~~2047|
415 |TC|TC d|0~~9999|
416 |SS|SS d|0~~9999|
417 |SC|SC d|0~~9999|
418 |CS|CS d|0~~9999|
419 |CC|CC d|0~~9999|
420 |SB|SB h|0~~FFFF|
421 |SM|SM d|0~~2047|
422 |STS|STS d|0~~1023|
423 |S|S d|0~~9999|
424 |DX|DX h|0~~FFFF|
425 |DY|DY h|0~~FFFF|
426 |TS|TS d|0~~9999|
427 |Dbit|Dbit d.d|0~~99999.0~~15|
428 |(% colspan="1" rowspan="9" %)Word
429 |W|W h|0~~FFFF|
430 |TN|TN d|0~~99999|
431 |SN|SN d|0~~99999|
432 |CN|CN d|0~~99999|
433 |R|R d|0~~99999|
434 |SW|SW h|0~~FFFF|
435 |Z|Z d|0~~99999|
436 |ZR|ZR h|0~~FFFF|
437 |D|D d|0~~99999|
438
439 **Cable Wiring**
440
441 **RS422**
442
443 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png||alt="image-20220825161612-8.png" height="278" width="612"]]
444
445 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png||alt="image-20220825160820-4.png" height="208" width="359"]]
446
447 == **L02 Ethernet ** ==
448
449 Mitsubishi L series CPU built-in Ethernet port.
450
451 **V-BOX Settings**
452
453 |**Items**|**Settings**|**Note**
454 |Protocol|MIT L02 CPU MELSEC|
455 |Connection|Ethernet|
456 |Port No.|1025|Must be the same as the PLC setting
457 |PLC station No.|0|Must be the same as the PLC setting
458
459 (% style="text-align:center" %)
460 [[image:三菱 L02以太网协议配置1.png]]
461
462 **PLC Settings (GX Works2 )**
463
464 Create a project
465
466 Set PLC IP, subnet mask and gateway;
467
468 Select [Binary Code] as communication data code;
469
470 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1||alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
471
472 Set PLC port number, for example 1025
473
474 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1||alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
475
476 Save settings;
477
478 Download project into PLC device;
479
480 Restart PLC device;
481
482 **Cable Wiring**
483
484 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
485
486 == {{id name="HQ12HSerial"/}}**Q12H Serial ** ==
487
488 This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
489
490 **[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]**
491
492 == **QJ71E71 Ethernet ** ==
493
494 Mitsubishi QJ71E71 Ethernet communication module;
495
496 **V-BOX Settings**
497
498 |**Items**|**Settings**|**Note**
499 |Protocol|MIT QJ71E71 MELSEC|
500 |Connection|Ethernet|
501 |Port No.|1025|Must be the same as the PLC setting
502 |PLC station No.|0|Must be the same as the PLC setting
503
504 (% style="text-align:center" %)
505 [[image:三菱 QJ71 以太网协议配置.png]]
506
507 **Address List**
508
509 |**Type**|**Device registers**|**Format**|**Range**|**Note**
510 |(% rowspan="18" %)Bit|X|X h|0~~1FFF|
511 |Y|Y h|0~~1FFF|
512 |M|M d|0~~99999|
513 |L|L d|0~~8191|
514 |F|F d|0~~2047|
515 |B|B h|0~~1FFF|
516 |V|V d|0~~2047|
517 |TS|TS d|0~~2047|
518 |TC|TC d|0~~2047|
519 |SS|SS d|0~~2047|
520 |SC|SC d|0~~2047|
521 |CS|CS d|0~~1023|
522 |CC|CC d|0~~1023|
523 |SB|SB h|0~~7FF|
524 |S|S d|0~~8191|
525 |DX|DX h|0~~1FFF|
526 |DY|DY h|0~~1FFF|
527 |SM|SM d|8000~~9999|
528 |(% rowspan="10" %)Word|SD|SD d|0~~2047|
529 |D|D d|0~~12287|
530 |W|W h|0~~1FFF|
531 |TN|TN d|0~~2047|
532 |SN|SN d|0~~2047|
533 |CN|CN d|0~~1023|
534 |R|R d|0~~32767|
535 |SW|SW h|0~~7FF|
536 |Z|Z d|0~~15|
537 |ZR|ZR h|0~~FE7FF|
538
539 **PLC Settings(GX Works2)**
540
541 * Click [Ethernet/CC IE/MELSECNET];
542 * Please select [Ethernet] as network type;
543 * Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
544 * Select [Online] as Mode;
545 * [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png||alt="image-20221119171343-2.png" height="341" width="587"]]
546 * Click [Operation setting] to set IP;
547 * Select [Binary Code] as [Communication Data Code];
548 * [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png||alt="image-20221119171436-3.png" height="354" width="588"]]
549 * Click [Open setting]
550 * Set protocol: TCP;
551 * Set [unpassive] in [Open system];
552 * Set [receive] in [Fixed buffer];
553 * Set [procedure Exist] in [Fixed buffer communication];
554 * Disable [Pairing open];
555 * Set [No confirm] in [Existence confirmation];
556 * Host station port number: 5009;
557 * Save settings;
558 * {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png||alt="image-20221119171611-4.png" height="354" width="588"]]
559 * Download project into PLC and restart it
560
561 **Cable Wiring**
562
563 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
564
565 == Q03UDV ==
566
567 Mitsubishi Q03UDV
568
569 **V-BOX Settings**
570
571 |**Items**|**Settings**|**Note**
572 |Protocol|MIT L02 CPU MELSEC PROTOCOL|
573 |Connection|Ethernet|
574 |Port No.|1025|Must be the same as the PLC setting
575 |PLC station No.|0|Must be the same as the PLC setting
576
577 [[image:1709779590561-640.png]]
578
579 **Address List**
580
581 |**Type**|**Device registers**|**Format**|**Range**|**Note**
582 |(% colspan="1" rowspan="18" %)Bit|X|X h|0~~1fff|
583 |Y|Y h|0~~1fff|
584 |SM|SM d|0~~2047|
585 |M|M d|0~~99999|
586 |L|L d|0~~8191|
587 |F|F d|0~~2047|
588 |V|V d|0~~2047|
589 |B|B h|0~~1fff|
590 |TS|TS d|0~~2047|
591 |TC|TC d|0~~2047|
592 |SS|SS d|0~~2047|
593 |SC|SC d|0~~2047|
594 |CS|CS d|0~~1023|
595 |CC|CC d|0~~1023|
596 |SB|SB h|0~~7ff|
597 |S|S d|0~~8191|
598 |DX|DX h|0~~1fff|
599 |DY|DY h|0~~1fff|
600 |(% colspan="1" rowspan="10" %)Word|SD|SD d|0~~2047|
601 |D|D d|0~~12287|
602 |W|W h|0~~1fff|
603 |TN|TN d|0~~2047|
604 |SN|SN d|0~~2047|
605 |CN|CN d|0~~1023|
606 |SW|SW h|0~~7ff|
607 |Z|Z d|0~~15|
608 |R|R d|0~~32767|
609 |ZR|ZR h|0~~fe7ff|
610
611 (% class="wikigeneratedid" id="HPLCSettings" %)
612 **PLC Settings(GX Works2)**
613
614 (% class="wikigeneratedid" %)
615 PC and PLC connection:
616
617 * Online→Read from PLC
618
619 (% style="text-align:center" %)
620 [[image:1.png]]
621
622 * choose PLC Series→OK
623
624 (% style="text-align:center" %)
625 [[image:StqCG53paq.png]]
626
627 * serial USB→OK
628
629 (% style="text-align:center" %)
630 [[image:Y7H80eq2Eb.png]]
631
632 * Choose Parameter、Global Device Comment and Device Memory→Execute
633
634 (% style="text-align:center" %)
635 [[image:6PAsdFz58I.png]]
636
637 * OK→wait loading successfully→Close
638
639 (% style="text-align:center" %)
640 [[image:0GBGUNn4hQ.png]]
641
642 * Navigation→Parameter→PLC Parameter→IP Address Setting→Built-in Ethernet Port Setting→Host Station(Same as the port on  V-box)→End
643
644 (% style="text-align:center" %)
645 [[image:Ypyl4SUHcf.png]]
646
647 * Debug→Start/ Stop Simulation→wait loading successfully→Close
648
649 (% style="text-align:center" %)
650 [[image:ZmUzFbS39y.png]]
651
652 (% style="text-align:center" %)
653 [[image:ehoO3C6bry.png]]
654
655 (% id="cke_bm_1296534S" style="display:none" %)** **(%%)**Cable Wiring**
656
657 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]