Wiki source code of Mitsubishi

Version 59.1 by Theodore Xu on 2023/09/15 11:25

version	line-number	content
40.1	1	== FX3U,3G,3GA Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	4
38.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
58.1	16	(% style="text-align:center" %)
	17	[[image:三菱 FX3U 串口协议配置.png]]
	18
38.1	19	Address List
2.1	20
	21	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	22	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	23	\|Y\|Y\|Y o\|0~~303237\|
	24	\|M\|M\|M d\|0~~99999\|
	25	\|T\|T\|T d\|0~~99999\|
	26	\|C\|C\|C d\|0~~99999\|
	27	\|S\|S\|S d\|0~~99999\|
	28	\|SM\|SM\|SM d\|8000~~9999\|
	29	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	30	\|Y\|Y\|Y o\|0~~303237\|
	31	\|M\|M\|M d\|0~~99999\|
	32	\|T\|T\|T d\|0~~99999\|
	33	\|C\|C\|C d\|0~~199\|
	34	\|D\|D\|D d\|0~~7999\|
	35	\|S\|S\|S d\|0~~99999\|
	36	\|SD\|SD\|SD d\|8000~~9999\|
	37
42.1	38	PLC Setting
2.1	39
42.1	40	Open GX Works2, create a new PLC project or open the project that has been created.
	41	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	42
	43	(% style="text-align:center" %)
	44	[[image:1.2.png]]
	45
	46	PLC Default Parameters:
	47	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	48	Note:The serial port parameters should be set depending on field requirements
	49
	50	PC and PLC connection:
	51
	52	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	53
	54	(% style="text-align:center" %)
	55	[[image:1.5.1.png]]
	56
	57	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	58
	59	(% style="text-align:center" %)
	60	[[image:1.5.2.png]]
	61
	62	Cable Wiring
	63
38.1	64	RS422
2.1	65
38.1	66	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	67
38.1	68	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	69
43.1	70	== FX NOPROTOCOL ==
	71
	72	Mitsubishi FX3G-RS232-BD
	73
	74	V-Box Settings
	75
	76	\|=Item\|=Settings\|=Note
	77	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	78	\|Connection\|RS232\|
	79	\|Baud rate\|9600\|
	80	\|Data bit\|7\|
	81	\|Parity\|EVEN\|
	82	\|Stop bit\|1\|
	83	\|PLC station No.\|0\|
	84
	85	(% style="text-align:center" %)
	86	[[image:三菱 FN盒子通讯配置.png]]
	87
	88	Address List
	89
	90	\|=Type\|=Device registers\|=HMI registers\|=Format\|=Range\|=Note
	91	\|(% rowspan="8" %)Bit\|X\|X\|X o\|0~~303237\|
	92	\|Y\|Y\|Y o\|0~~303237\|
	93	\|M\|M\|M d\|0~~99999\|
	94	\|T\|T\|T d\|0~~99999\|
	95	\|C\|C\|C d\|0~~99999\|
	96	\|S\|S\|S d\|0~~99999\|
	97	\|SM\|SM\|SM d\|8000~~9999\|
	98	\|Lamp\|Lamp\|Lamp d\|0~~0\|
	99	\|(% rowspan="8" %)Word\|X\|X\|X o\|0~~303237\|
	100	\|Y\|Y\|Y o\|0~~303237\|
	101	\|M\|M\|M d\|0~~99999\|
	102	\|T\|T\|T d\|0~~99999\|
	103	\|C\|C\|C d\|0~~199\|
	104	\|D\|D\|D d\|0~~7999\|
	105	\|S\|S\|S d\|0~~99999\|
	106	\|SD\|SD\|SD d\|8000~~9999\|
	107
45.1	108	Cable Wiring
43.1	109
44.1	110	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	111
41.1	112	== FX3U Ethernet ==
2.1	113
	114	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	115
41.1	116	V-BOX Settings
2.1	117
	118	\|Items\|Settings\|Note
	119	\|Protocol\|Mitsubishi FX3U\|
	120	\|Connection\|Ethernet\|
	121	\|Port No.\|5009\|Must be the same as the PLC setting
	122	\|PLC station No.\|0\|
	123
57.1	124	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b2cdc33b6eb92b67.png\|\|alt="image-20221119101946-2.png" height="395" width="695"]]
	125
41.1	126	Address List
2.1	127
	128	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	129	\|(% rowspan="7" %)Bit\|X\|X\|X OOO\|0~~377\|
	130	\|Y\|Y\|Y OOO\|0~~377\|
	131	\|M\|M\|M DDDD\|0~~7679\|
	132	\|SM\|SM\|SM DDDD\|8000~~8511\|
	133	\|S\|S\|S DDDD\|0~~4095\|
	134	\|TS\|TS\|TS DDD\|0~~511\|
	135	\|CS\|CS\|CS DDD\|0~~255\|
	136	\|(% rowspan="5" %)Word\|CN\|CN\|CN DDD\|0~~199\|
	137	\|TN\|TN\|TN DDD\|0~~511\|
	138	\|D\|D\|D DDDD\|0~~7999\|
	139	\|SD\|SD\|SD DDDD\|8000~~8511\|
	140	\|R\|R\|R DDDDD\|0~~32767\|
	141
41.1	142	Ethernet Module Settings
2.1	143
	144	FX3U-ENET-L module configuration
	145	Set up the FX3U-ENET-L Ethernet module settings as follows.
	146	Select the module location, which in this document is Module 0.
	147
41.1	148	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	149
	150	Select "Operational setting" to enter the following screen.
	151
	152	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	153
41.1	154	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dfbfdd586c855c47.png\|\|alt="image-20221116105947-1.png" height="573" width="706"]]
2.1	155
	156	Select "Open setting" to enter the setting interface, the settings are as follows.
	157
	158	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	159
	160	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	161
41.1	162	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	163
	164	Click on "transter setup" - "PC side I/F setting", see the following figure.
	165
	166	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	167
	168	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	169
41.1	170	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d6fd9ce3b96f99e2.png\|\|alt="image-20221116110832-2.png" height="423" width="708"]]
2.1	171
	172	Read and write data from the Ethernet module
	173
41.1	174	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png\|\|alt="image-20221116110907-3.png" height="549" width="706"]]
2.1	175
	176	Set "Transter setup" to COM communication, and read or write operation as shown below
	177
41.1	178	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png\|\|alt="image-20221116110917-4.png" height="549" width="706"]]
2.1	179
41.1	180	PLC Settings (GX Works 2)
2.1	181
	182	Create a blank FX5U project
	183
	184	Find Current Connection in the navigation
	185
41.1	186	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	187
	188	Select Connection Channel List
	189
	190	Select Ethernet board communication
	191
41.1	192	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	193
	194	Select Ethernet Module
	195	Set the IP address of the PLC
	196
41.1	197	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	198
	199	Read or write PLC data, in this document is read
	200
	201	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	202
41.1	203	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	204
46.1	205	== FX5U Serial ==
2.1	206
	207	Mitsubishi FX5U series PLC
	208
46.1	209	V-BOX Settings
2.1	210
	211	\|Item\|Settings\|Note
	212	\|Protocol\|Mitsubishi FX5U\|
	213	\|Connection\|RS422/RS485\|
	214	\|Baud rate\|9600\|
	215	\|Data bit\|7\|
	216	\|Parity\|Odd\|
	217	\|Stop bit\|1\|
	218	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	219
54.1	220	(% style="text-align:center" %)
	221	[[image:三菱 FX5U 串口协议配置.png]]
	222
46.1	223	Address List
2.1	224
	225	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	226	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	227	\|Y\|Y\|Y o\|0~~303237\|
	228	\|M\|M\|M d\|0~~99999\|
	229	\|B\|B\|B h\|0~~7FFF\|
	230	\|F\|F\|F d\|0~~32767\|
	231	\|SB\|SB\|SB h\|0~~7FFF\|
	232	\|TS\|TS\|TS d\|0~~1023\|
	233	\|TC\|TC\|TC d\|0~~1023\|
	234	\|STS\|STS\|STS d\|0~~1023\|
	235	\|STC\|STC\|STS d\|0~~1023\|
	236	\|CS\|CS\|CS d\|0~~1023\|
	237	\|CC\|CC\|CC d\|0~~1023\|
	238	\|SM\|SM\|SM d\|0~~9999\|
	239	\|L\|L\|L d\|0~~32767\|
	240	\|S\|S\|S d\|0~~4095\|
	241	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	242	\|TN\|TN\|TN d\|0~~1023\|
	243	\|STN\|STN\|STN d\|0~~1023\|
	244	\|CN\|CN\|CN d\|0~~1023\|
	245	\|R\|R\|R d\|0~~32767\|
	246	\|SW\|SW\|SW h\|0~~7FFF\|
	247	\|Z\|Z\|Z d\|0~~23\|
	248	\|D\|D\|D d\|0~~7999\|
	249	\|SD\|SD\|SD d\|0~~11999\|
	250
46.1	251	PLC Settings (GX Works 3)
2.1	252
	253	Create a blank FX5U project
	254
	255	Find the 485 serial port module in the system navigation bar and double click to enter the settings.
	256
46.1	257	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5c9cb13fac1e6c93.png?width=200&height=462&rev=1.1\|\|alt="12.PLC Protocol_html_5c9cb13fac1e6c93.png" height="462" width="200"]]
2.1	258
	259	Select protocol in the setting item, and set parameters.
	260
46.1	261	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_de942589ca070228.png?width=600&height=324&rev=1.1\|\|alt="12.PLC Protocol_html_de942589ca070228.png" height="324" width="600"]]
2.1	262
	263	Set station number, and [Message Pattern] (Pattern 1 or Pattern 4)
	264
46.1	265	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_387ec7d00b5feb59.png?width=600&height=323&rev=1.1\|\|alt="12.PLC Protocol_html_387ec7d00b5feb59.png" height="323" width="600"]]
2.1	266
	267	Click the [Apply] button to finish the setting.
	268
	269	Click download and select the items as below, then click [execute] to download the configuration to PLC.
	270
46.1	271	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cdef1c5ec8cc2105.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_cdef1c5ec8cc2105.png" height="434" width="600"]]
2.1	272
	273	As soon as download is completed, connect PLC with serial port, then configure it in the [Specify Connection Destination Connection].
	274
	275	Done.
	276
46.1	277	Cable Wiring
2.1	278
46.1	279	RS422
2.1	280
	281	{{id name="Iimage-20220825105105-2.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
	282
	283	{{id name="Iimage-20220825105533-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
	284
33.1	285	== FX5U Ethernet ==
2.1	286
	287	Mitsubishi FX5U series PLC
	288
59.1	289	V-BOX Settings
2.1	290
	291	\|Items\|Settings\|Note
	292	\|Protocol\|Mitsubishi FX5U\|
	293	\|Connection\|Ethernet\|
	294	\|Port No.\|5002\|Must be the same as the PLC setting
	295	\|PLC station No.\|0\|
	296
59.1	297	(% style="text-align:center" %)
	298	[[image:三菱 FX5U 以太网协议配置.png]]
2.1	299
59.1	300	Address List
	301
2.1	302	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	303	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	304	\|Y\|Y\|Y o\|0~~303237\|
	305	\|M\|M\|M d\|0~~99999\|
	306	\|B\|B\|B h\|0~~7FFF\|
	307	\|F\|F\|F d\|0~~32767\|
	308	\|SB\|SB\|SB h\|0~~7FFF\|
	309	\|TS\|TS\|TS d\|0~~1023\|
	310	\|TC\|TC\|TC d\|0~~1023\|
	311	\|STS\|STS\|STS d\|0~~1023\|
	312	\|STC\|STC\|STS d\|0~~1023\|
	313	\|CS\|CS\|CS d\|0~~1023\|
	314	\|CC\|CC\|CC d\|0~~1023\|
	315	\|SM\|SM\|SM d\|0~~9999\|
	316	\|L\|L\|L d\|0~~32767\|
	317	\|S\|S\|S d\|0~~4095\|
	318	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	319	\|TN\|TN\|TN d\|0~~1023\|
	320	\|STN\|STN\|STN d\|0~~1023\|
	321	\|CN\|CN\|CN d\|0~~1023\|
	322	\|R\|R\|R d\|0~~32767\|
	323	\|SW\|SW\|SW h\|0~~7FFF\|
	324	\|Z\|Z\|Z d\|0~~23\|
	325	\|D\|D\|D d\|0~~7999\|
	326	\|SD\|SD\|SD d\|0~~11999\|
	327
59.1	328	PLC Settings (GX Works 3)
2.1	329
	330	Find the [Ethernet port] in the navigation area.
	331
59.1	332	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8e8f85ace087346c.png?width=300&height=593&rev=1.1\|\|alt="12.PLC Protocol_html_8e8f85ace087346c.png" height="593" width="300"]]
2.1	333
	334	Select [Own Node Settings] in the [Setting Item List];
	335
	336	Set [IP Address], [Subnet Mask], [Default Gateway];
	337
	338	Click [Detailed Settings] into [Ethernet Configuration (Built-in Ethernet Port)] windows;
	339
59.1	340	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5d98495052c8c10e.png?width=600&height=339&rev=1.1\|\|alt="12.PLC Protocol_html_5d98495052c8c10e.png" height="339" width="600"]]
2.1	341
	342	Select [SLMP Connection Module] and add into host station as below picture shows;
	343
	344	Set Port number as 5002 (this is necessary settings);
	345
	346	Click [Close with Reflecting the Setting] to save and close window;
	347
59.1	348	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_14b489fdc6c6589d.png?width=600&height=350&rev=1.1\|\|alt="12.PLC Protocol_html_14b489fdc6c6589d.png" height="350" width="600"]]
2.1	349
	350	Click [Apply] to completed Etherenet settings;
	351
	352	Switch to the [On line data operation] interface as below, check the item and click [Execute] to download.
	353
59.1	354	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_c93025a968a8a9e7.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_c93025a968a8a9e7.png" height="434" width="600"]]
2.1	355
	356
59.1	357	Cable Wiring
2.1	358
33.1	359	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	360
47.1	361	== L02 Serial ==
2.1	362
	363	Mitsubishi L02 series CPU built-in serial port.
	364
47.1	365	V-BOX Settings
2.1	366
	367	\|Item\|Settings\|Note
	368	\|Protocol\|Mitsubishi L02\|
	369	\|Connection\|RS422\|
	370	\|Baud rate\|115200\|
	371	\|Data bit\|8\|
	372	\|Parity\|Odd\|
	373	\|Stop bit\|1\|
	374	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	375
53.1	376	(% style="text-align:center" %)
	377	[[image:三菱 L02串口协议配置.png]]
	378
47.1	379	Address List
2.1	380
	381	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
47.1	382	\|(% colspan="1" rowspan="20" %)Bit
	383	\|X\|X\|X h\|0~~FFFF\|
	384	\|Y\|Y\|Y h\|0~~FFFF\|
	385	\|M\|M\|M d\|0~~9999\|
	386	\|L\|L\|L d\|0~~9999\|
	387	\|F\|F\|F d\|0~~9999\|
	388	\|B\|B\|B h\|0~~FFFF\|
	389	\|V\|V\|V d\|0~~2047\|
	390	\|TC\|TC\|TC d\|0~~9999\|
	391	\|SS\|SS\|SS d\|0~~9999\|
	392	\|SC\|SC\|SC d\|0~~9999\|
	393	\|CS\|CS\|CS d\|0~~9999\|
	394	\|CC\|CC\|CC d\|0~~9999\|
	395	\|SB\|SB\|SB h\|0~~FFFF\|
	396	\|SM\|SM\|SM d\|0~~2047\|
	397	\|STS\|STS\|STS d\|0~~1023\|
	398	\|S\|S\|S d\|0~~9999\|
	399	\|DX\|DX\|DX h\|0~~FFFF\|
	400	\|DY\|DY\|DY h\|0~~FFFF\|
	401	\|TS\|TS\|TS d\|0~~9999\|
	402	\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	403	\|(% colspan="1" rowspan="9" %)Word
	404	\|W\|W\|W h\|0~~FFFF\|
	405	\|TN\|TN\|TN d\|0~~99999\|
	406	\|SN\|SN\|SN d\|0~~99999\|
	407	\|CN\|CN\|CN d\|0~~99999\|
	408	\|R\|R\|R d\|0~~99999\|
	409	\|SW\|SW\|SW h\|0~~FFFF\|
	410	\|Z\|Z\|Z d\|0~~99999\|
	411	\|ZR\|ZR\|ZR h\|0~~FFFF\|
	412	\|D\|D\|D d\|0~~99999\|
2.1	413
47.1	414	Cable Wiring
2.1	415
47.1	416	RS422
2.1	417
47.1	418	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
2.1	419
47.1	420	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
2.1	421
48.1	422	== L02 Ethernet ==
2.1	423
	424	Mitsubishi L series CPU built-in Ethernet port.
	425
48.1	426	V-BOX Settings
2.1	427
	428	\|Items\|Settings\|Note
	429	\|Protocol\|MIT L02 CPU MELSEC\|
	430	\|Connection\|Ethernet\|
	431	\|Port No.\|1025\|Must be the same as the PLC setting
	432	\|PLC station No.\|0\|Must be the same as the PLC setting
	433
52.1	434	(% style="text-align:center" %)
	435	[[image:三菱 L02以太网协议配置1.png]]
51.1	436
48.1	437	PLC Settings (GX Works2 )
2.1	438
	439	Create a project
	440
	441	Set PLC IP, subnet mask and gateway;
	442
	443	Select [Binary Code] as communication data code;
	444
49.1	445	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
2.1	446
	447	Set PLC port number, for example 1025
	448
49.1	449	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
2.1	450
	451	Save settings;
	452
	453	Download project into PLC device;
	454
	455	Restart PLC device;
	456
49.1	457	Cable Wiring
2.1	458
49.1	459	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	460
	461	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	462
	463	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	464
	465	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	466
32.1	467	== QJ71E71 Ethernet ==
2.1	468
	469	Mitsubishi QJ71E71 Ethernet communication module;
	470
50.1	471	V-BOX Settings
2.1	472
	473	\|Items\|Settings\|Note
	474	\|Protocol\|MIT QJ71E71 MELSEC\|
	475	\|Connection\|Ethernet\|
	476	\|Port No.\|1025\|Must be the same as the PLC setting
	477	\|PLC station No.\|0\|Must be the same as the PLC setting
	478
50.1	479	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50990385ef491b9e.png\|\|alt="image-20221119171832-5.png" height="354" width="625"]]
2.1	480
50.1	481	Address List
	482
2.1	483	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	484	\|(% rowspan="18" %)Bit\|X\|X\|X h\|0~~1FFF\|
	485	\|Y\|Y\|Y h\|0~~1FFF\|
	486	\|M\|M\|M d\|0~~99999\|
	487	\|L\|L\|L d\|0~~8191\|
	488	\|F\|F\|F d\|0~~2047\|
	489	\|B\|B\|B h\|0~~1FFF\|
	490	\|V\|V\|V d\|0~~2047\|
	491	\|TS\|TS\|TS d\|0~~2047\|
	492	\|TC\|TC\|TC d\|0~~2047\|
	493	\|SS\|SS\|SS d\|0~~2047\|
	494	\|SC\|SC\|SC d\|0~~2047\|
	495	\|CS\|CS\|CS d\|0~~1023\|
	496	\|CC\|CC\|CC d\|0~~1023\|
	497	\|SB\|SB\|SB h\|0~~7FF\|
	498	\|S\|S\|S d\|0~~8191\|
	499	\|DX\|DX\|DX h\|0~~1FFF\|
	500	\|DY\|DY\|DY h\|0~~1FFF\|
	501	\|SM\|SM\|SM d\|8000~~9999\|
	502	\|(% rowspan="10" %)Word\|SD\|SD\|SD d\|0~~2047\|
	503	\|D\|D\|D d\|0~~12287\|
	504	\|W\|W\|W h\|0~~1FFF\|
	505	\|TN\|TN\|TN d\|0~~2047\|
	506	\|SN\|SN\|SN d\|0~~2047\|
	507	\|CN\|CN\|CN d\|0~~1023\|
	508	\|R\|R\|R d\|0~~32767\|
	509	\|SW\|SW\|SW h\|0~~7FF\|
	510	\|Z\|Z\|Z d\|0~~15\|
	511	\|ZR\|ZR\|ZR h\|0~~FE7FF\|
	512
50.1	513	PLC Settings(GX Works2)
2.1	514
	515	* Click [Ethernet/CC IE/MELSECNET];
	516	* Please select [Ethernet] as network type;
	517	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	518	* Select [Online] as Mode;
50.1	519	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
2.1	520	* Click [Operation setting] to set IP;
	521	* Select [Binary Code] as [Communication Data Code];
50.1	522	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
2.1	523	* Click [Open setting]
	524	* Set protocol: TCP;
	525	* Set [unpassive] in [Open system];
	526	* Set [receive] in [Fixed buffer];
	527	* Set [procedure Exist] in [Fixed buffer communication];
	528	* Disable [Pairing open];
	529	* Set [No confirm] in [Existence confirmation];
	530	* Host station port number: 5009;
	531	* Save settings;
	532	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	533	* Download project into PLC and restart it
	534
50.1	535	Cable Wiring
2.1	536
34.1	537	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents