Wiki source code of Mitsubishi

Version 60.1 by Theodore Xu on 2023/09/15 11:34

version	line-number	content
40.1	1	== FX3U,3G,3GA Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	4
38.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
58.1	16	(% style="text-align:center" %)
	17	[[image:三菱 FX3U 串口协议配置.png]]
	18
38.1	19	Address List
2.1	20
	21	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	22	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	23	\|Y\|Y\|Y o\|0~~303237\|
	24	\|M\|M\|M d\|0~~99999\|
	25	\|T\|T\|T d\|0~~99999\|
	26	\|C\|C\|C d\|0~~99999\|
	27	\|S\|S\|S d\|0~~99999\|
	28	\|SM\|SM\|SM d\|8000~~9999\|
	29	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	30	\|Y\|Y\|Y o\|0~~303237\|
	31	\|M\|M\|M d\|0~~99999\|
	32	\|T\|T\|T d\|0~~99999\|
	33	\|C\|C\|C d\|0~~199\|
	34	\|D\|D\|D d\|0~~7999\|
	35	\|S\|S\|S d\|0~~99999\|
	36	\|SD\|SD\|SD d\|8000~~9999\|
	37
42.1	38	PLC Setting
2.1	39
42.1	40	Open GX Works2, create a new PLC project or open the project that has been created.
	41	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	42
	43	(% style="text-align:center" %)
	44	[[image:1.2.png]]
	45
	46	PLC Default Parameters:
	47	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	48	Note:The serial port parameters should be set depending on field requirements
	49
	50	PC and PLC connection:
	51
	52	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	53
	54	(% style="text-align:center" %)
	55	[[image:1.5.1.png]]
	56
	57	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	58
	59	(% style="text-align:center" %)
	60	[[image:1.5.2.png]]
	61
	62	Cable Wiring
	63
38.1	64	RS422
2.1	65
38.1	66	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	67
38.1	68	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	69
43.1	70	== FX NOPROTOCOL ==
	71
	72	Mitsubishi FX3G-RS232-BD
	73
	74	V-Box Settings
	75
	76	\|=Item\|=Settings\|=Note
	77	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	78	\|Connection\|RS232\|
	79	\|Baud rate\|9600\|
	80	\|Data bit\|7\|
	81	\|Parity\|EVEN\|
	82	\|Stop bit\|1\|
	83	\|PLC station No.\|0\|
	84
	85	(% style="text-align:center" %)
	86	[[image:三菱 FN盒子通讯配置.png]]
	87
	88	Address List
	89
	90	\|=Type\|=Device registers\|=HMI registers\|=Format\|=Range\|=Note
	91	\|(% rowspan="8" %)Bit\|X\|X\|X o\|0~~303237\|
	92	\|Y\|Y\|Y o\|0~~303237\|
	93	\|M\|M\|M d\|0~~99999\|
	94	\|T\|T\|T d\|0~~99999\|
	95	\|C\|C\|C d\|0~~99999\|
	96	\|S\|S\|S d\|0~~99999\|
	97	\|SM\|SM\|SM d\|8000~~9999\|
	98	\|Lamp\|Lamp\|Lamp d\|0~~0\|
	99	\|(% rowspan="8" %)Word\|X\|X\|X o\|0~~303237\|
	100	\|Y\|Y\|Y o\|0~~303237\|
	101	\|M\|M\|M d\|0~~99999\|
	102	\|T\|T\|T d\|0~~99999\|
	103	\|C\|C\|C d\|0~~199\|
	104	\|D\|D\|D d\|0~~7999\|
	105	\|S\|S\|S d\|0~~99999\|
	106	\|SD\|SD\|SD d\|8000~~9999\|
	107
45.1	108	Cable Wiring
43.1	109
44.1	110	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	111
41.1	112	== FX3U Ethernet ==
2.1	113
	114	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	115
41.1	116	V-BOX Settings
2.1	117
	118	\|Items\|Settings\|Note
	119	\|Protocol\|Mitsubishi FX3U\|
	120	\|Connection\|Ethernet\|
	121	\|Port No.\|5009\|Must be the same as the PLC setting
	122	\|PLC station No.\|0\|
	123
60.1	124	(% style="text-align:center" %)
	125	[[image:三菱 FX3U 以太网协议配置.png]]
57.1	126
41.1	127	Address List
2.1	128
	129	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	130	\|(% rowspan="7" %)Bit\|X\|X\|X OOO\|0~~377\|
	131	\|Y\|Y\|Y OOO\|0~~377\|
	132	\|M\|M\|M DDDD\|0~~7679\|
	133	\|SM\|SM\|SM DDDD\|8000~~8511\|
	134	\|S\|S\|S DDDD\|0~~4095\|
	135	\|TS\|TS\|TS DDD\|0~~511\|
	136	\|CS\|CS\|CS DDD\|0~~255\|
	137	\|(% rowspan="5" %)Word\|CN\|CN\|CN DDD\|0~~199\|
	138	\|TN\|TN\|TN DDD\|0~~511\|
	139	\|D\|D\|D DDDD\|0~~7999\|
	140	\|SD\|SD\|SD DDDD\|8000~~8511\|
	141	\|R\|R\|R DDDDD\|0~~32767\|
	142
41.1	143	Ethernet Module Settings
2.1	144
	145	FX3U-ENET-L module configuration
	146	Set up the FX3U-ENET-L Ethernet module settings as follows.
	147	Select the module location, which in this document is Module 0.
	148
41.1	149	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	150
	151	Select "Operational setting" to enter the following screen.
	152
	153	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	154
41.1	155	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dfbfdd586c855c47.png\|\|alt="image-20221116105947-1.png" height="573" width="706"]]
2.1	156
	157	Select "Open setting" to enter the setting interface, the settings are as follows.
	158
	159	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	160
	161	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	162
41.1	163	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	164
	165	Click on "transter setup" - "PC side I/F setting", see the following figure.
	166
	167	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	168
	169	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	170
41.1	171	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d6fd9ce3b96f99e2.png\|\|alt="image-20221116110832-2.png" height="423" width="708"]]
2.1	172
	173	Read and write data from the Ethernet module
	174
41.1	175	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png\|\|alt="image-20221116110907-3.png" height="549" width="706"]]
2.1	176
	177	Set "Transter setup" to COM communication, and read or write operation as shown below
	178
41.1	179	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png\|\|alt="image-20221116110917-4.png" height="549" width="706"]]
2.1	180
41.1	181	PLC Settings (GX Works 2)
2.1	182
	183	Create a blank FX5U project
	184
	185	Find Current Connection in the navigation
	186
41.1	187	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	188
	189	Select Connection Channel List
	190
	191	Select Ethernet board communication
	192
41.1	193	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	194
	195	Select Ethernet Module
	196	Set the IP address of the PLC
	197
41.1	198	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	199
	200	Read or write PLC data, in this document is read
	201
	202	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	203
41.1	204	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	205
46.1	206	== FX5U Serial ==
2.1	207
	208	Mitsubishi FX5U series PLC
	209
46.1	210	V-BOX Settings
2.1	211
	212	\|Item\|Settings\|Note
	213	\|Protocol\|Mitsubishi FX5U\|
	214	\|Connection\|RS422/RS485\|
	215	\|Baud rate\|9600\|
	216	\|Data bit\|7\|
	217	\|Parity\|Odd\|
	218	\|Stop bit\|1\|
	219	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	220
54.1	221	(% style="text-align:center" %)
	222	[[image:三菱 FX5U 串口协议配置.png]]
	223
46.1	224	Address List
2.1	225
	226	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	227	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	228	\|Y\|Y\|Y o\|0~~303237\|
	229	\|M\|M\|M d\|0~~99999\|
	230	\|B\|B\|B h\|0~~7FFF\|
	231	\|F\|F\|F d\|0~~32767\|
	232	\|SB\|SB\|SB h\|0~~7FFF\|
	233	\|TS\|TS\|TS d\|0~~1023\|
	234	\|TC\|TC\|TC d\|0~~1023\|
	235	\|STS\|STS\|STS d\|0~~1023\|
	236	\|STC\|STC\|STS d\|0~~1023\|
	237	\|CS\|CS\|CS d\|0~~1023\|
	238	\|CC\|CC\|CC d\|0~~1023\|
	239	\|SM\|SM\|SM d\|0~~9999\|
	240	\|L\|L\|L d\|0~~32767\|
	241	\|S\|S\|S d\|0~~4095\|
	242	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	243	\|TN\|TN\|TN d\|0~~1023\|
	244	\|STN\|STN\|STN d\|0~~1023\|
	245	\|CN\|CN\|CN d\|0~~1023\|
	246	\|R\|R\|R d\|0~~32767\|
	247	\|SW\|SW\|SW h\|0~~7FFF\|
	248	\|Z\|Z\|Z d\|0~~23\|
	249	\|D\|D\|D d\|0~~7999\|
	250	\|SD\|SD\|SD d\|0~~11999\|
	251
46.1	252	PLC Settings (GX Works 3)
2.1	253
	254	Create a blank FX5U project
	255
	256	Find the 485 serial port module in the system navigation bar and double click to enter the settings.
	257
46.1	258	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5c9cb13fac1e6c93.png?width=200&height=462&rev=1.1\|\|alt="12.PLC Protocol_html_5c9cb13fac1e6c93.png" height="462" width="200"]]
2.1	259
	260	Select protocol in the setting item, and set parameters.
	261
46.1	262	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_de942589ca070228.png?width=600&height=324&rev=1.1\|\|alt="12.PLC Protocol_html_de942589ca070228.png" height="324" width="600"]]
2.1	263
	264	Set station number, and [Message Pattern] (Pattern 1 or Pattern 4)
	265
46.1	266	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_387ec7d00b5feb59.png?width=600&height=323&rev=1.1\|\|alt="12.PLC Protocol_html_387ec7d00b5feb59.png" height="323" width="600"]]
2.1	267
	268	Click the [Apply] button to finish the setting.
	269
	270	Click download and select the items as below, then click [execute] to download the configuration to PLC.
	271
46.1	272	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cdef1c5ec8cc2105.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_cdef1c5ec8cc2105.png" height="434" width="600"]]
2.1	273
	274	As soon as download is completed, connect PLC with serial port, then configure it in the [Specify Connection Destination Connection].
	275
	276	Done.
	277
46.1	278	Cable Wiring
2.1	279
46.1	280	RS422
2.1	281
	282	{{id name="Iimage-20220825105105-2.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
	283
	284	{{id name="Iimage-20220825105533-3.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
	285
33.1	286	== FX5U Ethernet ==
2.1	287
	288	Mitsubishi FX5U series PLC
	289
59.1	290	V-BOX Settings
2.1	291
	292	\|Items\|Settings\|Note
	293	\|Protocol\|Mitsubishi FX5U\|
	294	\|Connection\|Ethernet\|
	295	\|Port No.\|5002\|Must be the same as the PLC setting
	296	\|PLC station No.\|0\|
	297
59.1	298	(% style="text-align:center" %)
	299	[[image:三菱 FX5U 以太网协议配置.png]]
2.1	300
59.1	301	Address List
	302
2.1	303	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	304	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	305	\|Y\|Y\|Y o\|0~~303237\|
	306	\|M\|M\|M d\|0~~99999\|
	307	\|B\|B\|B h\|0~~7FFF\|
	308	\|F\|F\|F d\|0~~32767\|
	309	\|SB\|SB\|SB h\|0~~7FFF\|
	310	\|TS\|TS\|TS d\|0~~1023\|
	311	\|TC\|TC\|TC d\|0~~1023\|
	312	\|STS\|STS\|STS d\|0~~1023\|
	313	\|STC\|STC\|STS d\|0~~1023\|
	314	\|CS\|CS\|CS d\|0~~1023\|
	315	\|CC\|CC\|CC d\|0~~1023\|
	316	\|SM\|SM\|SM d\|0~~9999\|
	317	\|L\|L\|L d\|0~~32767\|
	318	\|S\|S\|S d\|0~~4095\|
	319	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	320	\|TN\|TN\|TN d\|0~~1023\|
	321	\|STN\|STN\|STN d\|0~~1023\|
	322	\|CN\|CN\|CN d\|0~~1023\|
	323	\|R\|R\|R d\|0~~32767\|
	324	\|SW\|SW\|SW h\|0~~7FFF\|
	325	\|Z\|Z\|Z d\|0~~23\|
	326	\|D\|D\|D d\|0~~7999\|
	327	\|SD\|SD\|SD d\|0~~11999\|
	328
59.1	329	PLC Settings (GX Works 3)
2.1	330
	331	Find the [Ethernet port] in the navigation area.
	332
59.1	333	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8e8f85ace087346c.png?width=300&height=593&rev=1.1\|\|alt="12.PLC Protocol_html_8e8f85ace087346c.png" height="593" width="300"]]
2.1	334
	335	Select [Own Node Settings] in the [Setting Item List];
	336
	337	Set [IP Address], [Subnet Mask], [Default Gateway];
	338
	339	Click [Detailed Settings] into [Ethernet Configuration (Built-in Ethernet Port)] windows;
	340
59.1	341	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5d98495052c8c10e.png?width=600&height=339&rev=1.1\|\|alt="12.PLC Protocol_html_5d98495052c8c10e.png" height="339" width="600"]]
2.1	342
	343	Select [SLMP Connection Module] and add into host station as below picture shows;
	344
	345	Set Port number as 5002 (this is necessary settings);
	346
	347	Click [Close with Reflecting the Setting] to save and close window;
	348
59.1	349	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_14b489fdc6c6589d.png?width=600&height=350&rev=1.1\|\|alt="12.PLC Protocol_html_14b489fdc6c6589d.png" height="350" width="600"]]
2.1	350
	351	Click [Apply] to completed Etherenet settings;
	352
	353	Switch to the [On line data operation] interface as below, check the item and click [Execute] to download.
	354
59.1	355	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_c93025a968a8a9e7.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_c93025a968a8a9e7.png" height="434" width="600"]]
2.1	356
	357
59.1	358	Cable Wiring
2.1	359
33.1	360	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	361
47.1	362	== L02 Serial ==
2.1	363
	364	Mitsubishi L02 series CPU built-in serial port.
	365
47.1	366	V-BOX Settings
2.1	367
	368	\|Item\|Settings\|Note
	369	\|Protocol\|Mitsubishi L02\|
	370	\|Connection\|RS422\|
	371	\|Baud rate\|115200\|
	372	\|Data bit\|8\|
	373	\|Parity\|Odd\|
	374	\|Stop bit\|1\|
	375	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	376
53.1	377	(% style="text-align:center" %)
	378	[[image:三菱 L02串口协议配置.png]]
	379
47.1	380	Address List
2.1	381
	382	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
47.1	383	\|(% colspan="1" rowspan="20" %)Bit
	384	\|X\|X\|X h\|0~~FFFF\|
	385	\|Y\|Y\|Y h\|0~~FFFF\|
	386	\|M\|M\|M d\|0~~9999\|
	387	\|L\|L\|L d\|0~~9999\|
	388	\|F\|F\|F d\|0~~9999\|
	389	\|B\|B\|B h\|0~~FFFF\|
	390	\|V\|V\|V d\|0~~2047\|
	391	\|TC\|TC\|TC d\|0~~9999\|
	392	\|SS\|SS\|SS d\|0~~9999\|
	393	\|SC\|SC\|SC d\|0~~9999\|
	394	\|CS\|CS\|CS d\|0~~9999\|
	395	\|CC\|CC\|CC d\|0~~9999\|
	396	\|SB\|SB\|SB h\|0~~FFFF\|
	397	\|SM\|SM\|SM d\|0~~2047\|
	398	\|STS\|STS\|STS d\|0~~1023\|
	399	\|S\|S\|S d\|0~~9999\|
	400	\|DX\|DX\|DX h\|0~~FFFF\|
	401	\|DY\|DY\|DY h\|0~~FFFF\|
	402	\|TS\|TS\|TS d\|0~~9999\|
	403	\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	404	\|(% colspan="1" rowspan="9" %)Word
	405	\|W\|W\|W h\|0~~FFFF\|
	406	\|TN\|TN\|TN d\|0~~99999\|
	407	\|SN\|SN\|SN d\|0~~99999\|
	408	\|CN\|CN\|CN d\|0~~99999\|
	409	\|R\|R\|R d\|0~~99999\|
	410	\|SW\|SW\|SW h\|0~~FFFF\|
	411	\|Z\|Z\|Z d\|0~~99999\|
	412	\|ZR\|ZR\|ZR h\|0~~FFFF\|
	413	\|D\|D\|D d\|0~~99999\|
2.1	414
47.1	415	Cable Wiring
2.1	416
47.1	417	RS422
2.1	418
47.1	419	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
2.1	420
47.1	421	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
2.1	422
48.1	423	== L02 Ethernet ==
2.1	424
	425	Mitsubishi L series CPU built-in Ethernet port.
	426
48.1	427	V-BOX Settings
2.1	428
	429	\|Items\|Settings\|Note
	430	\|Protocol\|MIT L02 CPU MELSEC\|
	431	\|Connection\|Ethernet\|
	432	\|Port No.\|1025\|Must be the same as the PLC setting
	433	\|PLC station No.\|0\|Must be the same as the PLC setting
	434
52.1	435	(% style="text-align:center" %)
	436	[[image:三菱 L02以太网协议配置1.png]]
51.1	437
48.1	438	PLC Settings (GX Works2 )
2.1	439
	440	Create a project
	441
	442	Set PLC IP, subnet mask and gateway;
	443
	444	Select [Binary Code] as communication data code;
	445
49.1	446	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
2.1	447
	448	Set PLC port number, for example 1025
	449
49.1	450	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
2.1	451
	452	Save settings;
	453
	454	Download project into PLC device;
	455
	456	Restart PLC device;
	457
49.1	458	Cable Wiring
2.1	459
49.1	460	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	461
	462	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	463
	464	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	465
	466	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	467
32.1	468	== QJ71E71 Ethernet ==
2.1	469
	470	Mitsubishi QJ71E71 Ethernet communication module;
	471
50.1	472	V-BOX Settings
2.1	473
	474	\|Items\|Settings\|Note
	475	\|Protocol\|MIT QJ71E71 MELSEC\|
	476	\|Connection\|Ethernet\|
	477	\|Port No.\|1025\|Must be the same as the PLC setting
	478	\|PLC station No.\|0\|Must be the same as the PLC setting
	479
50.1	480	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50990385ef491b9e.png\|\|alt="image-20221119171832-5.png" height="354" width="625"]]
2.1	481
50.1	482	Address List
	483
2.1	484	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	485	\|(% rowspan="18" %)Bit\|X\|X\|X h\|0~~1FFF\|
	486	\|Y\|Y\|Y h\|0~~1FFF\|
	487	\|M\|M\|M d\|0~~99999\|
	488	\|L\|L\|L d\|0~~8191\|
	489	\|F\|F\|F d\|0~~2047\|
	490	\|B\|B\|B h\|0~~1FFF\|
	491	\|V\|V\|V d\|0~~2047\|
	492	\|TS\|TS\|TS d\|0~~2047\|
	493	\|TC\|TC\|TC d\|0~~2047\|
	494	\|SS\|SS\|SS d\|0~~2047\|
	495	\|SC\|SC\|SC d\|0~~2047\|
	496	\|CS\|CS\|CS d\|0~~1023\|
	497	\|CC\|CC\|CC d\|0~~1023\|
	498	\|SB\|SB\|SB h\|0~~7FF\|
	499	\|S\|S\|S d\|0~~8191\|
	500	\|DX\|DX\|DX h\|0~~1FFF\|
	501	\|DY\|DY\|DY h\|0~~1FFF\|
	502	\|SM\|SM\|SM d\|8000~~9999\|
	503	\|(% rowspan="10" %)Word\|SD\|SD\|SD d\|0~~2047\|
	504	\|D\|D\|D d\|0~~12287\|
	505	\|W\|W\|W h\|0~~1FFF\|
	506	\|TN\|TN\|TN d\|0~~2047\|
	507	\|SN\|SN\|SN d\|0~~2047\|
	508	\|CN\|CN\|CN d\|0~~1023\|
	509	\|R\|R\|R d\|0~~32767\|
	510	\|SW\|SW\|SW h\|0~~7FF\|
	511	\|Z\|Z\|Z d\|0~~15\|
	512	\|ZR\|ZR\|ZR h\|0~~FE7FF\|
	513
50.1	514	PLC Settings(GX Works2)
2.1	515
	516	* Click [Ethernet/CC IE/MELSECNET];
	517	* Please select [Ethernet] as network type;
	518	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	519	* Select [Online] as Mode;
50.1	520	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
2.1	521	* Click [Operation setting] to set IP;
	522	* Select [Binary Code] as [Communication Data Code];
50.1	523	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
2.1	524	* Click [Open setting]
	525	* Set protocol: TCP;
	526	* Set [unpassive] in [Open system];
	527	* Set [receive] in [Fixed buffer];
	528	* Set [procedure Exist] in [Fixed buffer communication];
	529	* Disable [Pairing open];
	530	* Set [No confirm] in [Existence confirmation];
	531	* Host station port number: 5009;
	532	* Save settings;
	533	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	534	* Download project into PLC and restart it
	535
50.1	536	Cable Wiring
2.1	537
34.1	538	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents