Wiki source code of Mitsubishi

Version 83.18 by Joe on 2024/04/29 14:33

version	line-number	content
40.1	1	== FX3U,3G,3GA Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	4
38.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
58.1	16	(% style="text-align:center" %)
	17	[[image:三菱 FX3U 串口协议配置.png]]
	18
38.1	19	Address List
2.1	20
67.1	21	\|Type\|Device registers\|Format\|Range\|Note
83.16	22	\|(% rowspan="7" %)Bit\|X\|X o\|0~~303237\|
67.1	23	\|Y\|Y o\|0~~303237\|
	24	\|M\|M d\|0~~99999\|
	25	\|T\|T d\|0~~99999\|
	26	\|C\|C d\|0~~99999\|
	27	\|S\|S d\|0~~99999\|
	28	\|SM\|SM d\|8000~~9999\|
83.16	29	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
67.1	30	\|Y\|Y o\|0~~303237\|
	31	\|M\|M d\|0~~99999\|
	32	\|T\|T d\|0~~99999\|
	33	\|C\|C d\|0~~199\|
	34	\|D\|D d\|0~~7999\|
	35	\|S\|S d\|0~~99999\|
	36	\|SD\|SD d\|8000~~9999\|
2.1	37
42.1	38	PLC Setting
2.1	39
42.1	40	Open GX Works2, create a new PLC project or open the project that has been created.
	41	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	42
	43	(% style="text-align:center" %)
77.1	44	[[image:GX2.png]]
	45
	46	(% style="text-align:center" %)
42.1	47	[[image:1.2.png]]
	48
	49	PLC Default Parameters:
	50	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	51	Note:The serial port parameters should be set depending on field requirements
	52
	53	PC and PLC connection:
	54
	55	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	56
	57	(% style="text-align:center" %)
	58	[[image:1.5.1.png]]
	59
	60	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	61
	62	(% style="text-align:center" %)
	63	[[image:1.5.2.png]]
	64
77.1	65	[PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
	66
	67	(% style="text-align:center" %)
78.1	68	[[image:FX3U串口下载.png]]
77.1	69
42.1	70	Cable Wiring
	71
38.1	72	RS422
2.1	73
38.1	74	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	75
38.1	76	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	77
43.1	78	== FX NOPROTOCOL ==
	79
	80	Mitsubishi FX3G-RS232-BD
	81
	82	V-Box Settings
	83
	84	\|=Item\|=Settings\|=Note
	85	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	86	\|Connection\|RS232\|
	87	\|Baud rate\|9600\|
	88	\|Data bit\|7\|
	89	\|Parity\|EVEN\|
	90	\|Stop bit\|1\|
	91	\|PLC station No.\|0\|
	92
	93	(% style="text-align:center" %)
	94	[[image:三菱 FN盒子通讯配置.png]]
	95
	96	Address List
	97
68.1	98	\|=Type\|=Device registers\|=Format\|=Range\|=Note
	99	\|(% rowspan="8" %)Bit\|X\|X o\|0~~303237\|
	100	\|Y\|Y o\|0~~303237\|
	101	\|M\|M d\|0~~99999\|
	102	\|T\|T d\|0~~99999\|
	103	\|C\|C d\|0~~99999\|
	104	\|S\|S d\|0~~99999\|
	105	\|SM\|SM d\|8000~~9999\|
	106	\|Lamp\|Lamp d\|0~~0\|
	107	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
	108	\|Y\|Y o\|0~~303237\|
	109	\|M\|M d\|0~~99999\|
	110	\|T\|T d\|0~~99999\|
	111	\|C\|C d\|0~~199\|
	112	\|D\|D d\|0~~7999\|
	113	\|S\|S d\|0~~99999\|
	114	\|SD\|SD d\|8000~~9999\|
43.1	115
45.1	116	Cable Wiring
43.1	117
44.1	118	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	119
41.1	120	== FX3U Ethernet ==
2.1	121
	122	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	123
41.1	124	V-BOX Settings
2.1	125
	126	\|Items\|Settings\|Note
	127	\|Protocol\|Mitsubishi FX3U\|
	128	\|Connection\|Ethernet\|
	129	\|Port No.\|5009\|Must be the same as the PLC setting
	130	\|PLC station No.\|0\|
	131
60.1	132	(% style="text-align:center" %)
	133	[[image:三菱 FX3U 以太网协议配置.png]]
57.1	134
41.1	135	Address List
2.1	136
69.1	137	\|Type\|Device registers\|Format\|Range\|Note
	138	\|(% rowspan="7" %)Bit\|X\|X OOO\|0~~377\|
	139	\|Y\|Y OOO\|0~~377\|
	140	\|M\|M DDDD\|0~~7679\|
	141	\|SM\|SM DDDD\|8000~~8511\|
	142	\|S\|S DDDD\|0~~4095\|
	143	\|TS\|TS DDD\|0~~511\|
	144	\|CS\|CS DDD\|0~~255\|
	145	\|(% rowspan="5" %)Word\|CN\|CN DDD\|0~~199\|
	146	\|TN\|TN DDD\|0~~511\|
	147	\|D\|D DDDD\|0~~7999\|
	148	\|SD\|SD DDDD\|8000~~8511\|
	149	\|R\|R DDDDD\|0~~32767\|
2.1	150
41.1	151	Ethernet Module Settings
2.1	152
	153	FX3U-ENET-L module configuration
	154	Set up the FX3U-ENET-L Ethernet module settings as follows.
	155	Select the module location, which in this document is Module 0.
	156
41.1	157	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	158
	159	Select "Operational setting" to enter the following screen.
	160
	161	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	162
83.18	163	(% style="text-align:center" %)
	164	[[image:894qM2hnau.png]]
2.1	165
	166	Select "Open setting" to enter the setting interface, the settings are as follows.
	167
	168	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	169
	170	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	171
41.1	172	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	173
	174	Click on "transter setup" - "PC side I/F setting", see the following figure.
	175
	176	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	177
	178	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	179
83.18	180	(% style="text-align:center" %)
	181	[[image:xzZboZHffh.png]]
2.1	182
83.18	183	(% style="text-align:center" %)
	184	[[image:ivWMdrv1Gh.png]]
2.1	185
83.18	186	(% style="text-align:center" %)
	187	[[image:qoQNWSBoEQ.png]]
	188
	189	read and write data from the Ethernet module
	190
41.1	191	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png\|\|alt="image-20221116110907-3.png" height="549" width="706"]]
2.1	192
	193	Set "Transter setup" to COM communication, and read or write operation as shown below
	194
41.1	195	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png\|\|alt="image-20221116110917-4.png" height="549" width="706"]]
2.1	196
41.1	197	PLC Settings (GX Works 2)
2.1	198
	199	Create a blank FX5U project
	200
	201	Find Current Connection in the navigation
	202
41.1	203	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	204
	205	Select Connection Channel List
	206
	207	Select Ethernet board communication
	208
41.1	209	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	210
	211	Select Ethernet Module
	212	Set the IP address of the PLC
	213
41.1	214	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	215
	216	Read or write PLC data, in this document is read
	217
	218	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	219
41.1	220	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	221
46.1	222	== FX5U Serial ==
2.1	223
	224	Mitsubishi FX5U series PLC
	225
46.1	226	V-BOX Settings
2.1	227
	228	\|Item\|Settings\|Note
	229	\|Protocol\|Mitsubishi FX5U\|
	230	\|Connection\|RS422/RS485\|
	231	\|Baud rate\|9600\|
	232	\|Data bit\|7\|
	233	\|Parity\|Odd\|
	234	\|Stop bit\|1\|
	235	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	236
54.1	237	(% style="text-align:center" %)
	238	[[image:三菱 FX5U 串口协议配置.png]]
	239
46.1	240	Address List
2.1	241
70.1	242	\|Type\|Device registers\|Format\|Range\|Note
	243	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	244	\|Y\|Y o\|0~~303237\|
	245	\|M\|M d\|0~~99999\|
	246	\|B\|B h\|0~~7FFF\|
	247	\|F\|F d\|0~~32767\|
	248	\|SB\|SB h\|0~~7FFF\|
	249	\|TS\|TS d\|0~~1023\|
	250	\|TC\|TC d\|0~~1023\|
	251	\|STS\|STS d\|0~~1023\|
	252	\|STC\|STS d\|0~~1023\|
	253	\|CS\|CS d\|0~~1023\|
	254	\|CC\|CC d\|0~~1023\|
	255	\|SM\|SM d\|0~~9999\|
	256	\|L\|L d\|0~~32767\|
	257	\|S\|S d\|0~~4095\|
	258	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	259	\|TN\|TN d\|0~~1023\|
	260	\|STN\|STN d\|0~~1023\|
	261	\|CN\|CN d\|0~~1023\|
	262	\|R\|R d\|0~~32767\|
	263	\|SW\|SW h\|0~~7FFF\|
	264	\|Z\|Z d\|0~~23\|
	265	\|D\|D d\|0~~7999\|
	266	\|SD\|SD d\|0~~11999\|
2.1	267
79.1	268	PLC Settings
2.1	269
	270	Create a blank FX5U project
	271
79.1	272	Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
2.1	273
79.1	274	(% style="text-align:center" %)
	275	[[image:GX3.png]]
2.1	276
	277
79.1	278	(% style="text-align:center" %)
	279	[[image:FX5U 串口选型号.png]]
2.1	280
79.1	281	PLC Default Parameters:
	282	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
2.1	283
79.1	284	(% style="text-align:center" %)
	285	[[image:FX5U plc串口参数配置.png]]
2.1	286
	287
79.1	288	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
2.1	289
79.1	290	{{info}}
	291	✎Note: The serial port parameters should be set depending on field requirements.
	292	{{/info}}
2.1	293
79.1	294	(% style="text-align:center" %)
	295	[[image:FX5U plc串口参数.png]]
2.1	296
46.1	297	Cable Wiring
2.1	298
46.1	299	RS422
2.1	300
80.1	301	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
2.1	302
80.1	303	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
2.1	304
33.1	305	== FX5U Ethernet ==
2.1	306
	307	Mitsubishi FX5U series PLC
	308
59.1	309	V-BOX Settings
2.1	310
	311	\|Items\|Settings\|Note
	312	\|Protocol\|Mitsubishi FX5U\|
	313	\|Connection\|Ethernet\|
	314	\|Port No.\|5002\|Must be the same as the PLC setting
	315	\|PLC station No.\|0\|
	316
59.1	317	(% style="text-align:center" %)
	318	[[image:三菱 FX5U 以太网协议配置.png]]
2.1	319
59.1	320	Address List
	321
71.1	322	\|Type\|Device registers\|Format\|Range\|Note
	323	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	324	\|Y\|Y o\|0~~303237\|
	325	\|M\|M d\|0~~99999\|
	326	\|B\|B h\|0~~7FFF\|
	327	\|F\|F d\|0~~32767\|
	328	\|SB\|SB h\|0~~7FFF\|
	329	\|TS\|TS d\|0~~1023\|
	330	\|TC\|TC d\|0~~1023\|
	331	\|STS\|STS d\|0~~1023\|
	332	\|STC\|STS d\|0~~1023\|
	333	\|CS\|CS d\|0~~1023\|
	334	\|CC\|CC d\|0~~1023\|
	335	\|SM\|SM d\|0~~9999\|
	336	\|L\|L d\|0~~32767\|
	337	\|S\|S d\|0~~4095\|
	338	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	339	\|TN\|TN d\|0~~1023\|
	340	\|STN\|STN d\|0~~1023\|
	341	\|CN\|CN d\|0~~1023\|
	342	\|R\|R d\|0~~32767\|
	343	\|SW\|SW h\|0~~7FFF\|
	344	\|Z\|Z d\|0~~23\|
	345	\|D\|D d\|0~~7999\|
	346	\|SD\|SD d\|0~~11999\|
2.1	347
81.1	348	PLC Settings
2.1	349
81.1	350	Open GX Works3, create a new PLC project or open the project that has been created.
	351
	352	Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
	353
75.2	354	(% style="text-align:center" %)
81.1	355	[[image:GX3.png]]
2.1	356
81.1	357	(% style="text-align:center" %)
	358	[[image:FX5U 串口选型号.png]]
	359
	360	PLC Default Parameters:
	361	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
	362
	363	(% style="text-align:center" %)
	364	[[image:FX5U 以太网配置.png]]
	365
75.2	366	[External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
2.1	367
75.2	368	(% style="text-align:center" %)
	369	[[image:1.3.2.png]]
2.1	370
81.1	371	PC and PLC connection
	372
	373	[Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
	374
	375	(% style="text-align:center" %)
	376	[[image:FX5U 以太网连接PLC.png]]
	377
	378	Downloading PLC project
	379	[Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
	380
	381	(% style="text-align:center" %)
	382	[[image:FX5U以太网下载.png]]
	383
59.1	384	Cable Wiring
2.1	385
33.1	386	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	387
47.1	388	== L02 Serial ==
2.1	389
	390	Mitsubishi L02 series CPU built-in serial port.
	391
47.1	392	V-BOX Settings
2.1	393
	394	\|Item\|Settings\|Note
	395	\|Protocol\|Mitsubishi L02\|
	396	\|Connection\|RS422\|
	397	\|Baud rate\|115200\|
	398	\|Data bit\|8\|
	399	\|Parity\|Odd\|
	400	\|Stop bit\|1\|
	401	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	402
53.1	403	(% style="text-align:center" %)
	404	[[image:三菱 L02串口协议配置.png]]
	405
47.1	406	Address List
2.1	407
72.1	408	\|Type\|Device registers\|Format\|Range\|Note
47.1	409	\|(% colspan="1" rowspan="20" %)Bit
72.1	410	\|X\|X h\|0~~FFFF\|
	411	\|Y\|Y h\|0~~FFFF\|
	412	\|M\|M d\|0~~9999\|
	413	\|L\|L d\|0~~9999\|
	414	\|F\|F d\|0~~9999\|
	415	\|B\|B h\|0~~FFFF\|
	416	\|V\|V d\|0~~2047\|
	417	\|TC\|TC d\|0~~9999\|
	418	\|SS\|SS d\|0~~9999\|
	419	\|SC\|SC d\|0~~9999\|
	420	\|CS\|CS d\|0~~9999\|
	421	\|CC\|CC d\|0~~9999\|
	422	\|SB\|SB h\|0~~FFFF\|
	423	\|SM\|SM d\|0~~2047\|
	424	\|STS\|STS d\|0~~1023\|
	425	\|S\|S d\|0~~9999\|
	426	\|DX\|DX h\|0~~FFFF\|
	427	\|DY\|DY h\|0~~FFFF\|
	428	\|TS\|TS d\|0~~9999\|
	429	\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
47.1	430	\|(% colspan="1" rowspan="9" %)Word
72.1	431	\|W\|W h\|0~~FFFF\|
	432	\|TN\|TN d\|0~~99999\|
	433	\|SN\|SN d\|0~~99999\|
	434	\|CN\|CN d\|0~~99999\|
	435	\|R\|R d\|0~~99999\|
	436	\|SW\|SW h\|0~~FFFF\|
	437	\|Z\|Z d\|0~~99999\|
	438	\|ZR\|ZR h\|0~~FFFF\|
	439	\|D\|D d\|0~~99999\|
2.1	440
47.1	441	Cable Wiring
2.1	442
47.1	443	RS422
2.1	444
47.1	445	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
2.1	446
47.1	447	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
2.1	448
48.1	449	== L02 Ethernet ==
2.1	450
	451	Mitsubishi L series CPU built-in Ethernet port.
	452
48.1	453	V-BOX Settings
2.1	454
	455	\|Items\|Settings\|Note
	456	\|Protocol\|MIT L02 CPU MELSEC\|
	457	\|Connection\|Ethernet\|
	458	\|Port No.\|1025\|Must be the same as the PLC setting
	459	\|PLC station No.\|0\|Must be the same as the PLC setting
	460
52.1	461	(% style="text-align:center" %)
	462	[[image:三菱 L02以太网协议配置1.png]]
51.1	463
48.1	464	PLC Settings (GX Works2 )
2.1	465
	466	Create a project
	467
	468	Set PLC IP, subnet mask and gateway;
	469
	470	Select [Binary Code] as communication data code;
	471
49.1	472	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
2.1	473
	474	Set PLC port number, for example 1025
	475
49.1	476	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
2.1	477
	478	Save settings;
	479
	480	Download project into PLC device;
	481
	482	Restart PLC device;
	483
49.1	484	Cable Wiring
2.1	485
49.1	486	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	487
	488	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	489
	490	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	491
	492	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	493
32.1	494	== QJ71E71 Ethernet ==
2.1	495
	496	Mitsubishi QJ71E71 Ethernet communication module;
	497
50.1	498	V-BOX Settings
2.1	499
	500	\|Items\|Settings\|Note
	501	\|Protocol\|MIT QJ71E71 MELSEC\|
	502	\|Connection\|Ethernet\|
	503	\|Port No.\|1025\|Must be the same as the PLC setting
	504	\|PLC station No.\|0\|Must be the same as the PLC setting
	505
61.1	506	(% style="text-align:center" %)
	507	[[image:三菱 QJ71 以太网协议配置.png]]
2.1	508
50.1	509	Address List
	510
74.1	511	\|Type\|Device registers\|Format\|Range\|Note
	512	\|(% rowspan="18" %)Bit\|X\|X h\|0~~1FFF\|
	513	\|Y\|Y h\|0~~1FFF\|
	514	\|M\|M d\|0~~99999\|
	515	\|L\|L d\|0~~8191\|
	516	\|F\|F d\|0~~2047\|
	517	\|B\|B h\|0~~1FFF\|
	518	\|V\|V d\|0~~2047\|
	519	\|TS\|TS d\|0~~2047\|
	520	\|TC\|TC d\|0~~2047\|
	521	\|SS\|SS d\|0~~2047\|
	522	\|SC\|SC d\|0~~2047\|
	523	\|CS\|CS d\|0~~1023\|
	524	\|CC\|CC d\|0~~1023\|
	525	\|SB\|SB h\|0~~7FF\|
	526	\|S\|S d\|0~~8191\|
	527	\|DX\|DX h\|0~~1FFF\|
	528	\|DY\|DY h\|0~~1FFF\|
	529	\|SM\|SM d\|8000~~9999\|
	530	\|(% rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
	531	\|D\|D d\|0~~12287\|
	532	\|W\|W h\|0~~1FFF\|
	533	\|TN\|TN d\|0~~2047\|
	534	\|SN\|SN d\|0~~2047\|
	535	\|CN\|CN d\|0~~1023\|
	536	\|R\|R d\|0~~32767\|
	537	\|SW\|SW h\|0~~7FF\|
	538	\|Z\|Z d\|0~~15\|
	539	\|ZR\|ZR h\|0~~FE7FF\|
2.1	540
50.1	541	PLC Settings(GX Works2)
2.1	542
	543	* Click [Ethernet/CC IE/MELSECNET];
	544	* Please select [Ethernet] as network type;
	545	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	546	* Select [Online] as Mode;
50.1	547	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
2.1	548	* Click [Operation setting] to set IP;
	549	* Select [Binary Code] as [Communication Data Code];
50.1	550	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
2.1	551	* Click [Open setting]
	552	* Set protocol: TCP;
	553	* Set [unpassive] in [Open system];
	554	* Set [receive] in [Fixed buffer];
	555	* Set [procedure Exist] in [Fixed buffer communication];
	556	* Disable [Pairing open];
	557	* Set [No confirm] in [Existence confirmation];
	558	* Host station port number: 5009;
	559	* Save settings;
	560	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	561	* Download project into PLC and restart it
	562
50.1	563	Cable Wiring
2.1	564
34.1	565	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
83.2	566
	567	== Q03UDV ==
83.3	568
	569	Mitsubishi Q03UDV
	570
	571	V-BOX Settings
	572
83.4	573	\|Items\|Settings\|Note
83.7	574	\|Protocol\|MIT L02 CPU MELSEC PROTOCOL\|
83.4	575	\|Connection\|Ethernet\|
83.5	576	\|Port No.\|1025\|Must be the same as the PLC setting
83.6	577	\|PLC station No.\|0\|Must be the same as the PLC setting
83.7	578
83.8	579	[[image:1709779590561-640.png]]
	580
	581	Address List
	582
	583	\|Type\|Device registers\|Format\|Range\|Note
	584	\|(% colspan="1" rowspan="18" %)Bit\|X\|X h\|0~~1fff\|
	585	\|Y\|Y h\|0~~1fff\|
	586	\|SM\|SM d\|0~~2047\|
	587	\|M\|M d\|0~~99999\|
	588	\|L\|L d\|0~~8191\|
	589	\|F\|F d\|0~~2047\|
	590	\|V\|V d\|0~~2047\|
	591	\|B\|B h\|0~~1fff\|
	592	\|TS\|TS d\|0~~2047\|
	593	\|TC\|TC d\|0~~2047\|
	594	\|SS\|SS d\|0~~2047\|
	595	\|SC\|SC d\|0~~2047\|
	596	\|CS\|CS d\|0~~1023\|
	597	\|CC\|CC d\|0~~1023\|
	598	\|SB\|SB h\|0~~7ff\|
	599	\|S\|S d\|0~~8191\|
	600	\|DX\|DX h\|0~~1fff\|
	601	\|DY\|DY h\|0~~1fff\|
83.9	602	\|(% colspan="1" rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
83.8	603	\|D\|D d\|0~~12287\|
	604	\|W\|W h\|0~~1fff\|
	605	\|TN\|TN d\|0~~2047\|
	606	\|SN\|SN d\|0~~2047\|
	607	\|CN\|CN d\|0~~1023\|
	608	\|SW\|SW h\|0~~7ff\|
	609	\|Z\|Z d\|0~~15\|
	610	\|R\|R d\|0~~32767\|
	611	\|ZR\|ZR h\|0~~fe7ff\|
83.10	612
83.12	613	(% class="wikigeneratedid" id="HPLCSettings" %)
	614	PLC Settings(GX Works2)
	615
	616	(% class="wikigeneratedid" %)
	617	PC and PLC connection:
	618
83.15	619	* Online→Read from PLC
83.12	620
	621	(% style="text-align:center" %)
	622	[[image:1.png]]
	623
83.15	624	* choose PLC Series→OK
83.14	625
83.12	626	(% style="text-align:center" %)
	627	[[image:StqCG53paq.png]]
	628
83.15	629	* serial USB→OK
83.14	630
83.12	631	(% style="text-align:center" %)
	632	[[image:Y7H80eq2Eb.png]]
	633
83.15	634	* Choose Parameter、Global Device Comment and Device Memory→Execute
83.14	635
83.12	636	(% style="text-align:center" %)
	637	[[image:6PAsdFz58I.png]]
	638
83.15	639	* OK→wait loading successfully→Close
83.14	640
83.13	641	(% style="text-align:center" %)
	642	[[image:0GBGUNn4hQ.png]]
	643
83.15	644	* Navigation→Parameter→PLC Parameter→IP Address Setting→Built-in Ethernet Port Setting→Host Station(Same as the port on V-box)→End
83.14	645
83.13	646	(% style="text-align:center" %)
	647	[[image:Ypyl4SUHcf.png]]
	648
83.15	649	* Debug→Start/ Stop Simulation→wait loading successfully→Close
83.14	650
83.13	651	(% style="text-align:center" %)
	652	[[image:ZmUzFbS39y.png]]
	653
	654	(% style="text-align:center" %)
	655	[[image:ehoO3C6bry.png]]
	656
83.15	657	(% id="cke_bm_1296534S" style="display:none" %) (%%)Cable Wiring
	658
	659	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents