Wiki source code of Mitsubishi

Version 83.3 by Joe on 2024/03/07 10:33

version	line-number	content
40.1	1	== FX3U,3G,3GA Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	4
38.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
58.1	16	(% style="text-align:center" %)
	17	[[image:三菱 FX3U 串口协议配置.png]]
	18
38.1	19	Address List
2.1	20
67.1	21	\|Type\|Device registers\|Format\|Range\|Note
	22	\|(% rowspan="7" %)Bit\|X\|Xo\|0~~303237\|
	23	\|Y\|Y o\|0~~303237\|
	24	\|M\|M d\|0~~99999\|
	25	\|T\|T d\|0~~99999\|
	26	\|C\|C d\|0~~99999\|
	27	\|S\|S d\|0~~99999\|
	28	\|SM\|SM d\|8000~~9999\|
	29	\|(% rowspan="8" %)Word\|X\|Xo\|0~~303237\|
	30	\|Y\|Y o\|0~~303237\|
	31	\|M\|M d\|0~~99999\|
	32	\|T\|T d\|0~~99999\|
	33	\|C\|C d\|0~~199\|
	34	\|D\|D d\|0~~7999\|
	35	\|S\|S d\|0~~99999\|
	36	\|SD\|SD d\|8000~~9999\|
2.1	37
42.1	38	PLC Setting
2.1	39
42.1	40	Open GX Works2, create a new PLC project or open the project that has been created.
	41	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	42
	43	(% style="text-align:center" %)
77.1	44	[[image:GX2.png]]
	45
	46	(% style="text-align:center" %)
42.1	47	[[image:1.2.png]]
	48
	49	PLC Default Parameters:
	50	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	51	Note:The serial port parameters should be set depending on field requirements
	52
	53	PC and PLC connection:
	54
	55	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	56
	57	(% style="text-align:center" %)
	58	[[image:1.5.1.png]]
	59
	60	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	61
	62	(% style="text-align:center" %)
	63	[[image:1.5.2.png]]
	64
77.1	65	[PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
	66
	67	(% style="text-align:center" %)
78.1	68	[[image:FX3U串口下载.png]]
77.1	69
42.1	70	Cable Wiring
	71
38.1	72	RS422
2.1	73
38.1	74	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	75
38.1	76	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	77
43.1	78	== FX NOPROTOCOL ==
	79
	80	Mitsubishi FX3G-RS232-BD
	81
	82	V-Box Settings
	83
	84	\|=Item\|=Settings\|=Note
	85	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	86	\|Connection\|RS232\|
	87	\|Baud rate\|9600\|
	88	\|Data bit\|7\|
	89	\|Parity\|EVEN\|
	90	\|Stop bit\|1\|
	91	\|PLC station No.\|0\|
	92
	93	(% style="text-align:center" %)
	94	[[image:三菱 FN盒子通讯配置.png]]
	95
	96	Address List
	97
68.1	98	\|=Type\|=Device registers\|=Format\|=Range\|=Note
	99	\|(% rowspan="8" %)Bit\|X\|X o\|0~~303237\|
	100	\|Y\|Y o\|0~~303237\|
	101	\|M\|M d\|0~~99999\|
	102	\|T\|T d\|0~~99999\|
	103	\|C\|C d\|0~~99999\|
	104	\|S\|S d\|0~~99999\|
	105	\|SM\|SM d\|8000~~9999\|
	106	\|Lamp\|Lamp d\|0~~0\|
	107	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
	108	\|Y\|Y o\|0~~303237\|
	109	\|M\|M d\|0~~99999\|
	110	\|T\|T d\|0~~99999\|
	111	\|C\|C d\|0~~199\|
	112	\|D\|D d\|0~~7999\|
	113	\|S\|S d\|0~~99999\|
	114	\|SD\|SD d\|8000~~9999\|
43.1	115
45.1	116	Cable Wiring
43.1	117
44.1	118	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	119
41.1	120	== FX3U Ethernet ==
2.1	121
	122	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	123
41.1	124	V-BOX Settings
2.1	125
	126	\|Items\|Settings\|Note
	127	\|Protocol\|Mitsubishi FX3U\|
	128	\|Connection\|Ethernet\|
	129	\|Port No.\|5009\|Must be the same as the PLC setting
	130	\|PLC station No.\|0\|
	131
60.1	132	(% style="text-align:center" %)
	133	[[image:三菱 FX3U 以太网协议配置.png]]
57.1	134
41.1	135	Address List
2.1	136
69.1	137	\|Type\|Device registers\|Format\|Range\|Note
	138	\|(% rowspan="7" %)Bit\|X\|X OOO\|0~~377\|
	139	\|Y\|Y OOO\|0~~377\|
	140	\|M\|M DDDD\|0~~7679\|
	141	\|SM\|SM DDDD\|8000~~8511\|
	142	\|S\|S DDDD\|0~~4095\|
	143	\|TS\|TS DDD\|0~~511\|
	144	\|CS\|CS DDD\|0~~255\|
	145	\|(% rowspan="5" %)Word\|CN\|CN DDD\|0~~199\|
	146	\|TN\|TN DDD\|0~~511\|
	147	\|D\|D DDDD\|0~~7999\|
	148	\|SD\|SD DDDD\|8000~~8511\|
	149	\|R\|R DDDDD\|0~~32767\|
2.1	150
41.1	151	Ethernet Module Settings
2.1	152
	153	FX3U-ENET-L module configuration
	154	Set up the FX3U-ENET-L Ethernet module settings as follows.
	155	Select the module location, which in this document is Module 0.
	156
41.1	157	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	158
	159	Select "Operational setting" to enter the following screen.
	160
	161	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	162
41.1	163	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dfbfdd586c855c47.png\|\|alt="image-20221116105947-1.png" height="573" width="706"]]
2.1	164
	165	Select "Open setting" to enter the setting interface, the settings are as follows.
	166
	167	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	168
	169	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	170
41.1	171	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	172
	173	Click on "transter setup" - "PC side I/F setting", see the following figure.
	174
	175	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	176
	177	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	178
41.1	179	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d6fd9ce3b96f99e2.png\|\|alt="image-20221116110832-2.png" height="423" width="708"]]
2.1	180
	181	Read and write data from the Ethernet module
	182
41.1	183	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png\|\|alt="image-20221116110907-3.png" height="549" width="706"]]
2.1	184
	185	Set "Transter setup" to COM communication, and read or write operation as shown below
	186
41.1	187	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png\|\|alt="image-20221116110917-4.png" height="549" width="706"]]
2.1	188
41.1	189	PLC Settings (GX Works 2)
2.1	190
	191	Create a blank FX5U project
	192
	193	Find Current Connection in the navigation
	194
41.1	195	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	196
	197	Select Connection Channel List
	198
	199	Select Ethernet board communication
	200
41.1	201	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	202
	203	Select Ethernet Module
	204	Set the IP address of the PLC
	205
41.1	206	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	207
	208	Read or write PLC data, in this document is read
	209
	210	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	211
41.1	212	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	213
46.1	214	== FX5U Serial ==
2.1	215
	216	Mitsubishi FX5U series PLC
	217
46.1	218	V-BOX Settings
2.1	219
	220	\|Item\|Settings\|Note
	221	\|Protocol\|Mitsubishi FX5U\|
	222	\|Connection\|RS422/RS485\|
	223	\|Baud rate\|9600\|
	224	\|Data bit\|7\|
	225	\|Parity\|Odd\|
	226	\|Stop bit\|1\|
	227	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	228
54.1	229	(% style="text-align:center" %)
	230	[[image:三菱 FX5U 串口协议配置.png]]
	231
46.1	232	Address List
2.1	233
70.1	234	\|Type\|Device registers\|Format\|Range\|Note
	235	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	236	\|Y\|Y o\|0~~303237\|
	237	\|M\|M d\|0~~99999\|
	238	\|B\|B h\|0~~7FFF\|
	239	\|F\|F d\|0~~32767\|
	240	\|SB\|SB h\|0~~7FFF\|
	241	\|TS\|TS d\|0~~1023\|
	242	\|TC\|TC d\|0~~1023\|
	243	\|STS\|STS d\|0~~1023\|
	244	\|STC\|STS d\|0~~1023\|
	245	\|CS\|CS d\|0~~1023\|
	246	\|CC\|CC d\|0~~1023\|
	247	\|SM\|SM d\|0~~9999\|
	248	\|L\|L d\|0~~32767\|
	249	\|S\|S d\|0~~4095\|
	250	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	251	\|TN\|TN d\|0~~1023\|
	252	\|STN\|STN d\|0~~1023\|
	253	\|CN\|CN d\|0~~1023\|
	254	\|R\|R d\|0~~32767\|
	255	\|SW\|SW h\|0~~7FFF\|
	256	\|Z\|Z d\|0~~23\|
	257	\|D\|D d\|0~~7999\|
	258	\|SD\|SD d\|0~~11999\|
2.1	259
79.1	260	PLC Settings
2.1	261
	262	Create a blank FX5U project
	263
79.1	264	Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
2.1	265
79.1	266	(% style="text-align:center" %)
	267	[[image:GX3.png]]
2.1	268
	269
79.1	270	(% style="text-align:center" %)
	271	[[image:FX5U 串口选型号.png]]
2.1	272
79.1	273	PLC Default Parameters:
	274	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
2.1	275
79.1	276	(% style="text-align:center" %)
	277	[[image:FX5U plc串口参数配置.png]]
2.1	278
	279
79.1	280	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
2.1	281
79.1	282	{{info}}
	283	✎Note: The serial port parameters should be set depending on field requirements.
	284	{{/info}}
2.1	285
79.1	286	(% style="text-align:center" %)
	287	[[image:FX5U plc串口参数.png]]
2.1	288
46.1	289	Cable Wiring
2.1	290
46.1	291	RS422
2.1	292
80.1	293	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
2.1	294
80.1	295	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
2.1	296
33.1	297	== FX5U Ethernet ==
2.1	298
	299	Mitsubishi FX5U series PLC
	300
59.1	301	V-BOX Settings
2.1	302
	303	\|Items\|Settings\|Note
	304	\|Protocol\|Mitsubishi FX5U\|
	305	\|Connection\|Ethernet\|
	306	\|Port No.\|5002\|Must be the same as the PLC setting
	307	\|PLC station No.\|0\|
	308
59.1	309	(% style="text-align:center" %)
	310	[[image:三菱 FX5U 以太网协议配置.png]]
2.1	311
59.1	312	Address List
	313
71.1	314	\|Type\|Device registers\|Format\|Range\|Note
	315	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	316	\|Y\|Y o\|0~~303237\|
	317	\|M\|M d\|0~~99999\|
	318	\|B\|B h\|0~~7FFF\|
	319	\|F\|F d\|0~~32767\|
	320	\|SB\|SB h\|0~~7FFF\|
	321	\|TS\|TS d\|0~~1023\|
	322	\|TC\|TC d\|0~~1023\|
	323	\|STS\|STS d\|0~~1023\|
	324	\|STC\|STS d\|0~~1023\|
	325	\|CS\|CS d\|0~~1023\|
	326	\|CC\|CC d\|0~~1023\|
	327	\|SM\|SM d\|0~~9999\|
	328	\|L\|L d\|0~~32767\|
	329	\|S\|S d\|0~~4095\|
	330	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	331	\|TN\|TN d\|0~~1023\|
	332	\|STN\|STN d\|0~~1023\|
	333	\|CN\|CN d\|0~~1023\|
	334	\|R\|R d\|0~~32767\|
	335	\|SW\|SW h\|0~~7FFF\|
	336	\|Z\|Z d\|0~~23\|
	337	\|D\|D d\|0~~7999\|
	338	\|SD\|SD d\|0~~11999\|
2.1	339
81.1	340	PLC Settings
2.1	341
81.1	342	Open GX Works3, create a new PLC project or open the project that has been created.
	343
	344	Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
	345
75.2	346	(% style="text-align:center" %)
81.1	347	[[image:GX3.png]]
2.1	348
81.1	349	(% style="text-align:center" %)
	350	[[image:FX5U 串口选型号.png]]
	351
	352	PLC Default Parameters:
	353	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
	354
	355	(% style="text-align:center" %)
	356	[[image:FX5U 以太网配置.png]]
	357
75.2	358	[External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
2.1	359
75.2	360	(% style="text-align:center" %)
	361	[[image:1.3.2.png]]
2.1	362
81.1	363	PC and PLC connection
	364
	365	[Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
	366
	367	(% style="text-align:center" %)
	368	[[image:FX5U 以太网连接PLC.png]]
	369
	370	Downloading PLC project
	371	[Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
	372
	373	(% style="text-align:center" %)
	374	[[image:FX5U以太网下载.png]]
	375
59.1	376	Cable Wiring
2.1	377
33.1	378	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	379
47.1	380	== L02 Serial ==
2.1	381
	382	Mitsubishi L02 series CPU built-in serial port.
	383
47.1	384	V-BOX Settings
2.1	385
	386	\|Item\|Settings\|Note
	387	\|Protocol\|Mitsubishi L02\|
	388	\|Connection\|RS422\|
	389	\|Baud rate\|115200\|
	390	\|Data bit\|8\|
	391	\|Parity\|Odd\|
	392	\|Stop bit\|1\|
	393	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	394
53.1	395	(% style="text-align:center" %)
	396	[[image:三菱 L02串口协议配置.png]]
	397
47.1	398	Address List
2.1	399
72.1	400	\|Type\|Device registers\|Format\|Range\|Note
47.1	401	\|(% colspan="1" rowspan="20" %)Bit
72.1	402	\|X\|X h\|0~~FFFF\|
	403	\|Y\|Y h\|0~~FFFF\|
	404	\|M\|M d\|0~~9999\|
	405	\|L\|L d\|0~~9999\|
	406	\|F\|F d\|0~~9999\|
	407	\|B\|B h\|0~~FFFF\|
	408	\|V\|V d\|0~~2047\|
	409	\|TC\|TC d\|0~~9999\|
	410	\|SS\|SS d\|0~~9999\|
	411	\|SC\|SC d\|0~~9999\|
	412	\|CS\|CS d\|0~~9999\|
	413	\|CC\|CC d\|0~~9999\|
	414	\|SB\|SB h\|0~~FFFF\|
	415	\|SM\|SM d\|0~~2047\|
	416	\|STS\|STS d\|0~~1023\|
	417	\|S\|S d\|0~~9999\|
	418	\|DX\|DX h\|0~~FFFF\|
	419	\|DY\|DY h\|0~~FFFF\|
	420	\|TS\|TS d\|0~~9999\|
	421	\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
47.1	422	\|(% colspan="1" rowspan="9" %)Word
72.1	423	\|W\|W h\|0~~FFFF\|
	424	\|TN\|TN d\|0~~99999\|
	425	\|SN\|SN d\|0~~99999\|
	426	\|CN\|CN d\|0~~99999\|
	427	\|R\|R d\|0~~99999\|
	428	\|SW\|SW h\|0~~FFFF\|
	429	\|Z\|Z d\|0~~99999\|
	430	\|ZR\|ZR h\|0~~FFFF\|
	431	\|D\|D d\|0~~99999\|
2.1	432
47.1	433	Cable Wiring
2.1	434
47.1	435	RS422
2.1	436
47.1	437	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
2.1	438
47.1	439	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
2.1	440
48.1	441	== L02 Ethernet ==
2.1	442
	443	Mitsubishi L series CPU built-in Ethernet port.
	444
48.1	445	V-BOX Settings
2.1	446
	447	\|Items\|Settings\|Note
	448	\|Protocol\|MIT L02 CPU MELSEC\|
	449	\|Connection\|Ethernet\|
	450	\|Port No.\|1025\|Must be the same as the PLC setting
	451	\|PLC station No.\|0\|Must be the same as the PLC setting
	452
52.1	453	(% style="text-align:center" %)
	454	[[image:三菱 L02以太网协议配置1.png]]
51.1	455
48.1	456	PLC Settings (GX Works2 )
2.1	457
	458	Create a project
	459
	460	Set PLC IP, subnet mask and gateway;
	461
	462	Select [Binary Code] as communication data code;
	463
49.1	464	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
2.1	465
	466	Set PLC port number, for example 1025
	467
49.1	468	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
2.1	469
	470	Save settings;
	471
	472	Download project into PLC device;
	473
	474	Restart PLC device;
	475
49.1	476	Cable Wiring
2.1	477
49.1	478	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	479
	480	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	481
	482	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	483
	484	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	485
32.1	486	== QJ71E71 Ethernet ==
2.1	487
	488	Mitsubishi QJ71E71 Ethernet communication module;
	489
50.1	490	V-BOX Settings
2.1	491
	492	\|Items\|Settings\|Note
	493	\|Protocol\|MIT QJ71E71 MELSEC\|
	494	\|Connection\|Ethernet\|
	495	\|Port No.\|1025\|Must be the same as the PLC setting
	496	\|PLC station No.\|0\|Must be the same as the PLC setting
	497
61.1	498	(% style="text-align:center" %)
	499	[[image:三菱 QJ71 以太网协议配置.png]]
2.1	500
50.1	501	Address List
	502
74.1	503	\|Type\|Device registers\|Format\|Range\|Note
	504	\|(% rowspan="18" %)Bit\|X\|X h\|0~~1FFF\|
	505	\|Y\|Y h\|0~~1FFF\|
	506	\|M\|M d\|0~~99999\|
	507	\|L\|L d\|0~~8191\|
	508	\|F\|F d\|0~~2047\|
	509	\|B\|B h\|0~~1FFF\|
	510	\|V\|V d\|0~~2047\|
	511	\|TS\|TS d\|0~~2047\|
	512	\|TC\|TC d\|0~~2047\|
	513	\|SS\|SS d\|0~~2047\|
	514	\|SC\|SC d\|0~~2047\|
	515	\|CS\|CS d\|0~~1023\|
	516	\|CC\|CC d\|0~~1023\|
	517	\|SB\|SB h\|0~~7FF\|
	518	\|S\|S d\|0~~8191\|
	519	\|DX\|DX h\|0~~1FFF\|
	520	\|DY\|DY h\|0~~1FFF\|
	521	\|SM\|SM d\|8000~~9999\|
	522	\|(% rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
	523	\|D\|D d\|0~~12287\|
	524	\|W\|W h\|0~~1FFF\|
	525	\|TN\|TN d\|0~~2047\|
	526	\|SN\|SN d\|0~~2047\|
	527	\|CN\|CN d\|0~~1023\|
	528	\|R\|R d\|0~~32767\|
	529	\|SW\|SW h\|0~~7FF\|
	530	\|Z\|Z d\|0~~15\|
	531	\|ZR\|ZR h\|0~~FE7FF\|
2.1	532
50.1	533	PLC Settings(GX Works2)
2.1	534
	535	* Click [Ethernet/CC IE/MELSECNET];
	536	* Please select [Ethernet] as network type;
	537	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	538	* Select [Online] as Mode;
50.1	539	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
2.1	540	* Click [Operation setting] to set IP;
	541	* Select [Binary Code] as [Communication Data Code];
50.1	542	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
2.1	543	* Click [Open setting]
	544	* Set protocol: TCP;
	545	* Set [unpassive] in [Open system];
	546	* Set [receive] in [Fixed buffer];
	547	* Set [procedure Exist] in [Fixed buffer communication];
	548	* Disable [Pairing open];
	549	* Set [No confirm] in [Existence confirmation];
	550	* Host station port number: 5009;
	551	* Save settings;
	552	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	553	* Download project into PLC and restart it
	554
50.1	555	Cable Wiring
2.1	556
34.1	557	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
83.2	558
	559	== Q03UDV ==
83.3	560
	561	Mitsubishi Q03UDV
	562
	563	V-BOX Settings
	564
	565	\|Item\|Settings\|Note
	566	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	567	\|Connection\|RS422/RS485/RS232\|
	568	\|Baud rate\|9600~~115200\|
	569	\|Data bit\|7/8\|
	570	\|Parity\|EVEN/Odd/None\|
	571	\|Stop bit\|1/2\|
	572	\|PLC station No.\|1~~255

Wiki source code of Mitsubishi

Navigation

Table of Contents