Skip to Content

Wiki source code of Mitsubishi

Version 83.9 by Joe on 2024/03/07 11:39
Show last authors
1 == **FX3U,3G,3GA Serial ** ==
2
3 Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
4
5 **V-BOX Settings**
6
7 |**Item**|**Settings**|**Note**
8 |Protocol|Mitsubishi FX3U/3G/3GA|
9 |Connection|RS422/RS485/RS232|
10 |Baud rate|9600~~115200|
11 |Data bit|7/8|
12 |Parity|EVEN/Odd/None|
13 |Stop bit|1/2|
14 |PLC station No.|1~~255|
15
16 (% style="text-align:center" %)
17 [[image:三菱 FX3U 串口协议配置.png]]
18
19 **Address List**
20
21 |**Type**|**Device registers**|**Format**|**Range**|**Note**
22 |(% rowspan="7" %)Bit|X|Xo|0~~303237|
23 |Y|Y o|0~~303237|
24 |M|M d|0~~99999|
25 |T|T d|0~~99999|
26 |C|C d|0~~99999|
27 |S|S d|0~~99999|
28 |SM|SM d|8000~~9999|
29 |(% rowspan="8" %)Word|X|Xo|0~~303237|
30 |Y|Y o|0~~303237|
31 |M|M d|0~~99999|
32 |T|T d|0~~99999|
33 |C|C d|0~~199|
34 |D|D d|0~~7999|
35 |S|S d|0~~99999|
36 |SD|SD d|8000~~9999|
37
38 **PLC Setting**
39
40 Open GX Works2, create a new PLC project or open the project that has been created.
41 Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
42
43 (% style="text-align:center" %)
44 [[image:GX2.png]]
45
46 (% style="text-align:center" %)
47 [[image:1.2.png]]
48
49 PLC Default Parameters:
50 [Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
51 Note:The serial port parameters should be set depending on field requirements
52
53 PC and PLC connection:
54
55 [All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
56
57 (% style="text-align:center" %)
58 [[image:1.5.1.png]]
59
60 Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
61
62 (% style="text-align:center" %)
63 [[image:1.5.2.png]]
64
65 [PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
66
67 (% style="text-align:center" %)
68 [[image:FX3U串口下载.png]]
69
70 **Cable Wiring**
71
72 **RS422**
73
74 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png||alt="image-20220825103421-5.png" height="296" width="715"]]
75
76 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png||alt="image-20220825100845-4.png" height="246" width="419"]]
77
78 == **FX NOPROTOCOL** ==
79
80 Mitsubishi FX3G-RS232-BD
81
82 **V-Box Settings**
83
84 |=**Item**|=**Settings**|=**Note**
85 |Protocol|Mitsubishi FX NOPROTOCOL|
86 |Connection|RS232|
87 |Baud rate|9600|
88 |Data bit|7|
89 |Parity|EVEN|
90 |Stop bit|1|
91 |PLC station No.|0|
92
93 (% style="text-align:center" %)
94 [[image:三菱 FN盒子通讯配置.png]]
95
96 **Address List**
97
98 |=**Type**|=**Device registers**|=**Format**|=**Range**|=**Note**
99 |(% rowspan="8" %)Bit|X|X o|0~~303237|
100 |Y|Y o|0~~303237|
101 |M|M d|0~~99999|
102 |T|T d|0~~99999|
103 |C|C d|0~~99999|
104 |S|S d|0~~99999|
105 |SM|SM d|8000~~9999|
106 |Lamp|Lamp d|0~~0|
107 |(% rowspan="8" %)Word|X|X o|0~~303237|
108 |Y|Y o|0~~303237|
109 |M|M d|0~~99999|
110 |T|T d|0~~99999|
111 |C|C d|0~~199|
112 |D|D d|0~~7999|
113 |S|S d|0~~99999|
114 |SD|SD d|8000~~9999|
115
116 **Cable Wiring**
117
118 [[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
119
120 == **FX3U Ethernet ** ==
121
122 Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
123
124 **V-BOX Settings**
125
126 |Items|Settings|Note
127 |Protocol|Mitsubishi FX3U|
128 |Connection|Ethernet|
129 |Port No.|5009|Must be the same as the PLC setting
130 |PLC station No.|0|
131
132 (% style="text-align:center" %)
133 [[image:三菱 FX3U 以太网协议配置.png]]
134
135 **Address List**
136
137 |**Type**|**Device registers**|**Format**|**Range**|**Note**
138 |(% rowspan="7" %)Bit|X|X OOO|0~~377|
139 |Y|Y OOO|0~~377|
140 |M|M DDDD|0~~7679|
141 |SM|SM DDDD|8000~~8511|
142 |S|S DDDD|0~~4095|
143 |TS|TS DDD|0~~511|
144 |CS|CS DDD|0~~255|
145 |(% rowspan="5" %)Word|CN|CN DDD|0~~199|
146 |TN|TN DDD|0~~511|
147 |D|D DDDD|0~~7999|
148 |SD|SD DDDD|8000~~8511|
149 |R|R DDDDD|0~~32767|
150
151 **Ethernet Module Settings**
152
153 FX3U-ENET-L module configuration
154 Set up the FX3U-ENET-L Ethernet module settings as follows.
155 Select the module location, which in this document is Module 0.
156
157 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png||alt="image-20221116105850-1.png" height="573" width="706"]]
158
159 Select "Operational setting" to enter the following screen.
160
161 The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
162
163 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_dfbfdd586c855c47.png||alt="image-20221116105947-1.png" height="573" width="706"]]
164
165 Select "Open setting" to enter the setting interface, the settings are as follows.
166
167 The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
168
169 Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
170
171 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png||alt="image-20221116110802-1.png" height="549" width="706"]]
172
173 Click on "transter setup" - "PC side I/F setting", see the following figure.
174
175 After setting, the first download must use the programming cable, as shown in the figure; after that, can
176
177 use the IP set in the "Ethernet board" to communicate directly with the network cable.
178
179 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d6fd9ce3b96f99e2.png||alt="image-20221116110832-2.png" height="423" width="708"]]
180
181 Read and write data from the Ethernet module
182
183 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_690b3e57b29cfd4b.png||alt="image-20221116110907-3.png" height="549" width="706"]]
184
185 Set "Transter setup" to COM communication, and read or write operation as shown below
186
187 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_b317253742f7151.png||alt="image-20221116110917-4.png" height="549" width="706"]]
188
189 **PLC Settings (GX Works 2)**
190
191 Create a blank FX5U project
192
193 Find Current Connection in the navigation
194
195 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png||alt="image-20221116111427-1.png" height="421" width="705"]]
196
197 Select Connection Channel List
198
199 Select Ethernet board communication
200
201 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png||alt="image-20221116111451-2.png" height="421" width="705"]]
202
203 Select Ethernet Module
204 Set the IP address of the PLC
205
206 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png||alt="image-20221116111509-3.png" height="666" width="699"]]
207
208 Read or write PLC data, in this document is read
209
210 {{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png||alt="image-20221116111651-4.png" height="416" width="697"]]
211
212 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png||alt="image-20221116111727-5.png" height="416" width="697"]]
213
214 == **FX5U Serial ** ==
215
216 Mitsubishi FX5U series PLC
217
218 **V-BOX Settings**
219
220 |**Item**|**Settings**|**Note**
221 |Protocol|Mitsubishi FX5U|
222 |Connection|RS422/RS485|
223 |Baud rate|9600|
224 |Data bit|7|
225 |Parity|Odd|
226 |Stop bit|1|
227 |PLC station No.|1~~255|Need to be the same as PLC settings
228
229 (% style="text-align:center" %)
230 [[image:三菱 FX5U 串口协议配置.png]]
231
232 **Address List**
233
234 |**Type**|**Device registers**|**Format**|**Range**|**Note**
235 |(% rowspan="15" %)Bit|X|X o|0~~303237|
236 |Y|Y o|0~~303237|
237 |M|M d|0~~99999|
238 |B|B h|0~~7FFF|
239 |F|F d|0~~32767|
240 |SB|SB h|0~~7FFF|
241 |TS|TS d|0~~1023|
242 |TC|TC d|0~~1023|
243 |STS|STS d|0~~1023|
244 |STC|STS d|0~~1023|
245 |CS|CS d|0~~1023|
246 |CC|CC d|0~~1023|
247 |SM|SM d|0~~9999|
248 |L|L d|0~~32767|
249 |S|S d|0~~4095|
250 |(% rowspan="9" %)Word|W|W h|0~~3FF|
251 |TN|TN d|0~~1023|
252 |STN|STN d|0~~1023|
253 |CN|CN d|0~~1023|
254 |R|R d|0~~32767|
255 |SW|SW h|0~~7FFF|
256 |Z|Z d|0~~23|
257 |D|D d|0~~7999|
258 |SD|SD d|0~~11999|
259
260 **PLC Settings **
261
262 Create a blank FX5U project
263
264 Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
265
266 (% style="text-align:center" %)
267 [[image:GX3.png]]
268
269
270 (% style="text-align:center" %)
271 [[image:FX5U 串口选型号.png]]
272
273 PLC Default Parameters: 
274 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
275
276 (% style="text-align:center" %)
277 [[image:FX5U plc串口参数配置.png]]
278
279
280 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
281
282 {{info}}
283 **✎Note:** The serial port parameters should be set depending on field requirements.
284 {{/info}}
285
286 (% style="text-align:center" %)
287 [[image:FX5U plc串口参数.png]]
288
289 **Cable Wiring**
290
291 **RS422**
292
293 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png||alt="image-20220825105105-2.png" height="288" width="711"]]
294
295 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png||alt="image-20220825105533-3.png" height="246" width="420"]]
296
297 == **FX5U Ethernet ** ==
298
299 Mitsubishi FX5U series PLC
300
301 **V-BOX Settings**
302
303 |**Items**|**Settings**|**Note**
304 |Protocol|Mitsubishi FX5U|
305 |Connection|Ethernet|
306 |Port No.|5002|Must be the same as the PLC setting
307 |PLC station No.|0|
308
309 (% style="text-align:center" %)
310 [[image:三菱 FX5U 以太网协议配置.png]]
311
312 **Address List**
313
314 |**Type**|**Device registers**|**Format**|**Range**|**Note**
315 |(% rowspan="15" %)Bit|X|X o|0~~303237|
316 |Y|Y o|0~~303237|
317 |M|M d|0~~99999|
318 |B|B h|0~~7FFF|
319 |F|F d|0~~32767|
320 |SB|SB h|0~~7FFF|
321 |TS|TS d|0~~1023|
322 |TC|TC d|0~~1023|
323 |STS|STS d|0~~1023|
324 |STC|STS d|0~~1023|
325 |CS|CS d|0~~1023|
326 |CC|CC d|0~~1023|
327 |SM|SM d|0~~9999|
328 |L|L d|0~~32767|
329 |S|S d|0~~4095|
330 |(% rowspan="9" %)Word|W|W h|0~~3FF|
331 |TN|TN d|0~~1023|
332 |STN|STN d|0~~1023|
333 |CN|CN d|0~~1023|
334 |R|R d|0~~32767|
335 |SW|SW h|0~~7FFF|
336 |Z|Z d|0~~23|
337 |D|D d|0~~7999|
338 |SD|SD d|0~~11999|
339
340 **PLC Settings **
341
342 Open GX Works3, create a new PLC project or open the project that has been created.
343
344 Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
345
346 (% style="text-align:center" %)
347 [[image:GX3.png]]
348
349 (% style="text-align:center" %)
350 [[image:FX5U 串口选型号.png]]
351
352 PLC Default Parameters: 
353 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
354
355 (% style="text-align:center" %)
356 [[image:FX5U 以太网配置.png]]
357
358 [External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
359
360 (% style="text-align:center" %)
361 [[image:1.3.2.png]]
362
363 PC and PLC connection
364
365 [Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
366
367 (% style="text-align:center" %)
368 [[image:FX5U 以太网连接PLC.png]]
369
370 Downloading PLC project
371 [Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
372
373 (% style="text-align:center" %)
374 [[image:FX5U以太网下载.png]]
375
376 **Cable Wiring**
377
378 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
379
380 == **L02 Serial ** ==
381
382 Mitsubishi L02 series CPU built-in serial port.
383
384 **V-BOX Settings**
385
386 |**Item**|**Settings**|**Note**
387 |Protocol|Mitsubishi L02|
388 |Connection|RS422|
389 |Baud rate|115200|
390 |Data bit|8|
391 |Parity|Odd|
392 |Stop bit|1|
393 |PLC station No.|1~~255|Need to be the same as PLC settings
394
395 (% style="text-align:center" %)
396 [[image:三菱 L02串口协议配置.png]]
397
398 **Address List**
399
400 |**Type**|**Device registers**|**Format**|**Range**|**Note**
401 |(% colspan="1" rowspan="20" %)Bit
402 |X|X h|0~~FFFF|
403 |Y|Y h|0~~FFFF|
404 |M|M d|0~~9999|
405 |L|L d|0~~9999|
406 |F|F d|0~~9999|
407 |B|B h|0~~FFFF|
408 |V|V d|0~~2047|
409 |TC|TC d|0~~9999|
410 |SS|SS d|0~~9999|
411 |SC|SC d|0~~9999|
412 |CS|CS d|0~~9999|
413 |CC|CC d|0~~9999|
414 |SB|SB h|0~~FFFF|
415 |SM|SM d|0~~2047|
416 |STS|STS d|0~~1023|
417 |S|S d|0~~9999|
418 |DX|DX h|0~~FFFF|
419 |DY|DY h|0~~FFFF|
420 |TS|TS d|0~~9999|
421 |Dbit|Dbit d.d|0~~99999.0~~15|
422 |(% colspan="1" rowspan="9" %)Word
423 |W|W h|0~~FFFF|
424 |TN|TN d|0~~99999|
425 |SN|SN d|0~~99999|
426 |CN|CN d|0~~99999|
427 |R|R d|0~~99999|
428 |SW|SW h|0~~FFFF|
429 |Z|Z d|0~~99999|
430 |ZR|ZR h|0~~FFFF|
431 |D|D d|0~~99999|
432
433 **Cable Wiring**
434
435 **RS422**
436
437 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png||alt="image-20220825161612-8.png" height="278" width="612"]]
438
439 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png||alt="image-20220825160820-4.png" height="208" width="359"]]
440
441 == **L02 Ethernet ** ==
442
443 Mitsubishi L series CPU built-in Ethernet port.
444
445 **V-BOX Settings**
446
447 |**Items**|**Settings**|**Note**
448 |Protocol|MIT L02 CPU MELSEC|
449 |Connection|Ethernet|
450 |Port No.|1025|Must be the same as the PLC setting
451 |PLC station No.|0|Must be the same as the PLC setting
452
453 (% style="text-align:center" %)
454 [[image:三菱 L02以太网协议配置1.png]]
455
456 **PLC Settings (GX Works2 )**
457
458 Create a project
459
460 Set PLC IP, subnet mask and gateway;
461
462 Select [Binary Code] as communication data code;
463
464 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1||alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
465
466 Set PLC port number, for example 1025
467
468 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1||alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
469
470 Save settings;
471
472 Download project into PLC device;
473
474 Restart PLC device;
475
476 **Cable Wiring**
477
478 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
479
480 == {{id name="HQ12HSerial"/}}**Q12H Serial ** ==
481
482 This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
483
484 **[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]**
485
486 == **QJ71E71 Ethernet ** ==
487
488 Mitsubishi QJ71E71 Ethernet communication module;
489
490 **V-BOX Settings**
491
492 |**Items**|**Settings**|**Note**
493 |Protocol|MIT QJ71E71 MELSEC|
494 |Connection|Ethernet|
495 |Port No.|1025|Must be the same as the PLC setting
496 |PLC station No.|0|Must be the same as the PLC setting
497
498 (% style="text-align:center" %)
499 [[image:三菱 QJ71 以太网协议配置.png]]
500
501 **Address List**
502
503 |**Type**|**Device registers**|**Format**|**Range**|**Note**
504 |(% rowspan="18" %)Bit|X|X h|0~~1FFF|
505 |Y|Y h|0~~1FFF|
506 |M|M d|0~~99999|
507 |L|L d|0~~8191|
508 |F|F d|0~~2047|
509 |B|B h|0~~1FFF|
510 |V|V d|0~~2047|
511 |TS|TS d|0~~2047|
512 |TC|TC d|0~~2047|
513 |SS|SS d|0~~2047|
514 |SC|SC d|0~~2047|
515 |CS|CS d|0~~1023|
516 |CC|CC d|0~~1023|
517 |SB|SB h|0~~7FF|
518 |S|S d|0~~8191|
519 |DX|DX h|0~~1FFF|
520 |DY|DY h|0~~1FFF|
521 |SM|SM d|8000~~9999|
522 |(% rowspan="10" %)Word|SD|SD d|0~~2047|
523 |D|D d|0~~12287|
524 |W|W h|0~~1FFF|
525 |TN|TN d|0~~2047|
526 |SN|SN d|0~~2047|
527 |CN|CN d|0~~1023|
528 |R|R d|0~~32767|
529 |SW|SW h|0~~7FF|
530 |Z|Z d|0~~15|
531 |ZR|ZR h|0~~FE7FF|
532
533 **PLC Settings(GX Works2)**
534
535 * Click [Ethernet/CC IE/MELSECNET];
536 * Please select [Ethernet] as network type;
537 * Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
538 * Select [Online] as Mode;
539 * [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png||alt="image-20221119171343-2.png" height="341" width="587"]]
540 * Click [Operation setting] to set IP;
541 * Select [Binary Code] as [Communication Data Code];
542 * [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png||alt="image-20221119171436-3.png" height="354" width="588"]]
543 * Click [Open setting]
544 * Set protocol: TCP;
545 * Set [unpassive] in [Open system];
546 * Set [receive] in [Fixed buffer];
547 * Set [procedure Exist] in [Fixed buffer communication];
548 * Disable [Pairing open];
549 * Set [No confirm] in [Existence confirmation];
550 * Host station port number: 5009;
551 * Save settings;
552 * {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png||alt="image-20221119171611-4.png" height="354" width="588"]]
553 * Download project into PLC and restart it
554
555 **Cable Wiring**
556
557 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
558
559 == Q03UDV ==
560
561 Mitsubishi Q03UDV
562
563 **V-BOX Settings**
564
565 |**Items**|**Settings**|**Note**
566 |Protocol|MIT L02 CPU MELSEC PROTOCOL|
567 |Connection|Ethernet|
568 |Port No.|1025|Must be the same as the PLC setting
569 |PLC station No.|0|Must be the same as the PLC setting
570
571 [[image:1709779590561-640.png]]
572
573 **Address List**
574
575 |**Type**|**Device registers**|**Format**|**Range**|**Note**
576 |(% colspan="1" rowspan="18" %)Bit|X|X h|0~~1fff|
577 |Y|Y h|0~~1fff|
578 |SM|SM d|0~~2047|
579 |M|M d|0~~99999|
580 |L|L d|0~~8191|
581 |F|F d|0~~2047|
582 |V|V d|0~~2047|
583 |B|B h|0~~1fff|
584 |TS|TS d|0~~2047|
585 |TC|TC d|0~~2047|
586 |SS|SS d|0~~2047|
587 |SC|SC d|0~~2047|
588 |CS|CS d|0~~1023|
589 |CC|CC d|0~~1023|
590 |SB|SB h|0~~7ff|
591 |S|S d|0~~8191|
592 |DX|DX h|0~~1fff|
593 |DY|DY h|0~~1fff|
594 |(% colspan="1" rowspan="10" %)Word|SD|SD d|0~~2047|
595 |D|D d|0~~12287|
596 |W|W h|0~~1fff|
597 |TN|TN d|0~~2047|
598 |SN|SN d|0~~2047|
599 |CN|CN d|0~~1023|
600 |SW|SW h|0~~7ff|
601 |Z|Z d|0~~15|
602 |R|R d|0~~32767|
603 |ZR|ZR h|0~~fe7ff|