Skip to Content

Wiki source code of Mitsubishi

Version 84.1 by Joe on 2024/04/29 14:40
Show last authors
1 == **FX3U,3G,3GA Serial ** ==
2
3 Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
4
5 **V-BOX Settings**
6
7 |**Item**|**Settings**|**Note**
8 |Protocol|Mitsubishi FX3U/3G/3GA|
9 |Connection|RS422/RS485/RS232|
10 |Baud rate|9600~~115200|
11 |Data bit|7/8|
12 |Parity|EVEN/Odd/None|
13 |Stop bit|1/2|
14 |PLC station No.|1~~255|
15
16 (% style="text-align:center" %)
17 [[image:三菱 FX3U 串口协议配置.png]]
18
19 **Address List**
20
21 |**Type**|**Device registers**|**Format**|**Range**|**Note**
22 |(% rowspan="7" %)Bit|X|X o|0~~303237|
23 |Y|Y o|0~~303237|
24 |M|M d|0~~99999|
25 |T|T d|0~~99999|
26 |C|C d|0~~99999|
27 |S|S d|0~~99999|
28 |SM|SM d|8000~~9999|
29 |(% rowspan="8" %)Word|X|X o|0~~303237|
30 |Y|Y o|0~~303237|
31 |M|M d|0~~99999|
32 |T|T d|0~~99999|
33 |C|C d|0~~199|
34 |D|D d|0~~7999|
35 |S|S d|0~~99999|
36 |SD|SD d|8000~~9999|
37
38 **PLC Setting**
39
40 Open GX Works2, create a new PLC project or open the project that has been created.
41 Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
42
43 (% style="text-align:center" %)
44 [[image:GX2.png]]
45
46 (% style="text-align:center" %)
47 [[image:1.2.png]]
48
49 PLC Default Parameters:
50 [Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
51 Note:The serial port parameters should be set depending on field requirements
52
53 PC and PLC connection:
54
55 [All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
56
57 (% style="text-align:center" %)
58 [[image:1.5.1.png]]
59
60 Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
61
62 (% style="text-align:center" %)
63 [[image:1.5.2.png]]
64
65 [PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
66
67 (% style="text-align:center" %)
68 [[image:FX3U串口下载.png]]
69
70 **Cable Wiring**
71
72 **RS422**
73
74 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png||alt="image-20220825103421-5.png" height="296" width="715"]]
75
76 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png||alt="image-20220825100845-4.png" height="246" width="419"]]
77
78 == **FX NOPROTOCOL** ==
79
80 Mitsubishi FX3G-RS232-BD
81
82 **V-Box Settings**
83
84 |=**Item**|=**Settings**|=**Note**
85 |Protocol|Mitsubishi FX NOPROTOCOL|
86 |Connection|RS232|
87 |Baud rate|9600|
88 |Data bit|7|
89 |Parity|EVEN|
90 |Stop bit|1|
91 |PLC station No.|0|
92
93 (% style="text-align:center" %)
94 [[image:三菱 FN盒子通讯配置.png]]
95
96 **Address List**
97
98 |=**Type**|=**Device registers**|=**Format**|=**Range**|=**Note**
99 |(% rowspan="8" %)Bit|X|X o|0~~303237|
100 |Y|Y o|0~~303237|
101 |M|M d|0~~99999|
102 |T|T d|0~~99999|
103 |C|C d|0~~99999|
104 |S|S d|0~~99999|
105 |SM|SM d|8000~~9999|
106 |Lamp|Lamp d|0~~0|
107 |(% rowspan="8" %)Word|X|X o|0~~303237|
108 |Y|Y o|0~~303237|
109 |M|M d|0~~99999|
110 |T|T d|0~~99999|
111 |C|C d|0~~199|
112 |D|D d|0~~7999|
113 |S|S d|0~~99999|
114 |SD|SD d|8000~~9999|
115
116 **Cable Wiring**
117
118 [[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
119
120 == **FX3U Ethernet ** ==
121
122 Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
123
124 **V-BOX Settings**
125
126 |Items|Settings|Note
127 |Protocol|Mitsubishi FX3U|
128 |Connection|Ethernet|
129 |Port No.|5009|Must be the same as the PLC setting
130 |PLC station No.|0|
131
132 (% style="text-align:center" %)
133 [[image:三菱 FX3U 以太网协议配置.png]]
134
135 **Address List**
136
137 |**Type**|**Device registers**|**Format**|**Range**|**Note**
138 |(% rowspan="7" %)Bit|X|X OOO|0~~377|
139 |Y|Y OOO|0~~377|
140 |M|M DDDD|0~~7679|
141 |SM|SM DDDD|8000~~8511|
142 |S|S DDDD|0~~4095|
143 |TS|TS DDD|0~~511|
144 |CS|CS DDD|0~~255|
145 |(% rowspan="5" %)Word|CN|CN DDD|0~~199|
146 |TN|TN DDD|0~~511|
147 |D|D DDDD|0~~7999|
148 |SD|SD DDDD|8000~~8511|
149 |R|R DDDDD|0~~32767|
150
151 **Ethernet Module Settings**
152
153 FX3U-ENET-L module configuration
154 Set up the FX3U-ENET-L Ethernet module settings as follows.
155 Select the module location, which in this document is Module 0.
156
157 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png||alt="image-20221116105850-1.png" height="573" width="706"]]
158
159 Select "Operational setting" to enter the following screen.
160
161 The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
162
163 (% style="text-align:center" %)
164 [[image:894qM2hnau.png]]
165
166 Select "Open setting" to enter the setting interface, the settings are as follows.
167
168 The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
169
170 Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
171
172 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png||alt="image-20221116110802-1.png" height="549" width="706"]]
173
174 Click on "transter setup" - "PC side I/F setting", see the following figure.
175
176 After setting, the first download must use the programming cable, as shown in the figure; after that, can
177
178 use the IP set in the "Ethernet board" to communicate directly with the network cable.
179
180 (% style="text-align:center" %)
181 [[image:xzZboZHffh.png]]
182
183 (% style="text-align:center" %)
184 [[image:ivWMdrv1Gh.png]]
185
186 (% style="text-align:center" %)
187 [[image:qoQNWSBoEQ.png]]
188
189
190 **PLC Settings (GX Works 2)**
191
192 Create a blank FX5U project
193
194 Find Current Connection in the navigation
195
196 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png||alt="image-20221116111427-1.png" height="421" width="705"]]
197
198 Select Connection Channel List
199
200 Select Ethernet board communication
201
202 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png||alt="image-20221116111451-2.png" height="421" width="705"]]
203
204 Select Ethernet Module
205 Set the IP address of the PLC
206
207 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png||alt="image-20221116111509-3.png" height="666" width="699"]]
208
209 Read or write PLC data, in this document is read
210
211 {{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png||alt="image-20221116111651-4.png" height="416" width="697"]]
212
213 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png||alt="image-20221116111727-5.png" height="416" width="697"]]
214
215 == **FX5U Serial ** ==
216
217 Mitsubishi FX5U series PLC
218
219 **V-BOX Settings**
220
221 |**Item**|**Settings**|**Note**
222 |Protocol|Mitsubishi FX5U|
223 |Connection|RS422/RS485|
224 |Baud rate|9600|
225 |Data bit|7|
226 |Parity|Odd|
227 |Stop bit|1|
228 |PLC station No.|1~~255|Need to be the same as PLC settings
229
230 (% style="text-align:center" %)
231 [[image:三菱 FX5U 串口协议配置.png]]
232
233 **Address List**
234
235 |**Type**|**Device registers**|**Format**|**Range**|**Note**
236 |(% rowspan="15" %)Bit|X|X o|0~~303237|
237 |Y|Y o|0~~303237|
238 |M|M d|0~~99999|
239 |B|B h|0~~7FFF|
240 |F|F d|0~~32767|
241 |SB|SB h|0~~7FFF|
242 |TS|TS d|0~~1023|
243 |TC|TC d|0~~1023|
244 |STS|STS d|0~~1023|
245 |STC|STS d|0~~1023|
246 |CS|CS d|0~~1023|
247 |CC|CC d|0~~1023|
248 |SM|SM d|0~~9999|
249 |L|L d|0~~32767|
250 |S|S d|0~~4095|
251 |(% rowspan="9" %)Word|W|W h|0~~3FF|
252 |TN|TN d|0~~1023|
253 |STN|STN d|0~~1023|
254 |CN|CN d|0~~1023|
255 |R|R d|0~~32767|
256 |SW|SW h|0~~7FFF|
257 |Z|Z d|0~~23|
258 |D|D d|0~~7999|
259 |SD|SD d|0~~11999|
260
261 **PLC Settings **
262
263 Create a blank FX5U project
264
265 Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
266
267 (% style="text-align:center" %)
268 [[image:GX3.png]]
269
270
271 (% style="text-align:center" %)
272 [[image:FX5U 串口选型号.png]]
273
274 PLC Default Parameters: 
275 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
276
277 (% style="text-align:center" %)
278 [[image:FX5U plc串口参数配置.png]]
279
280
281 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
282
283 {{info}}
284 **✎Note:** The serial port parameters should be set depending on field requirements.
285 {{/info}}
286
287 (% style="text-align:center" %)
288 [[image:FX5U plc串口参数.png]]
289
290 **Cable Wiring**
291
292 **RS422**
293
294 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png||alt="image-20220825105105-2.png" height="288" width="711"]]
295
296 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png||alt="image-20220825105533-3.png" height="246" width="420"]]
297
298 == **FX5U Ethernet ** ==
299
300 Mitsubishi FX5U series PLC
301
302 **V-BOX Settings**
303
304 |**Items**|**Settings**|**Note**
305 |Protocol|Mitsubishi FX5U|
306 |Connection|Ethernet|
307 |Port No.|5002|Must be the same as the PLC setting
308 |PLC station No.|0|
309
310 (% style="text-align:center" %)
311 [[image:三菱 FX5U 以太网协议配置.png]]
312
313 **Address List**
314
315 |**Type**|**Device registers**|**Format**|**Range**|**Note**
316 |(% rowspan="15" %)Bit|X|X o|0~~303237|
317 |Y|Y o|0~~303237|
318 |M|M d|0~~99999|
319 |B|B h|0~~7FFF|
320 |F|F d|0~~32767|
321 |SB|SB h|0~~7FFF|
322 |TS|TS d|0~~1023|
323 |TC|TC d|0~~1023|
324 |STS|STS d|0~~1023|
325 |STC|STS d|0~~1023|
326 |CS|CS d|0~~1023|
327 |CC|CC d|0~~1023|
328 |SM|SM d|0~~9999|
329 |L|L d|0~~32767|
330 |S|S d|0~~4095|
331 |(% rowspan="9" %)Word|W|W h|0~~3FF|
332 |TN|TN d|0~~1023|
333 |STN|STN d|0~~1023|
334 |CN|CN d|0~~1023|
335 |R|R d|0~~32767|
336 |SW|SW h|0~~7FFF|
337 |Z|Z d|0~~23|
338 |D|D d|0~~7999|
339 |SD|SD d|0~~11999|
340
341 **PLC Settings **
342
343 Open GX Works3, create a new PLC project or open the project that has been created.
344
345 Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
346
347 (% style="text-align:center" %)
348 [[image:GX3.png]]
349
350 (% style="text-align:center" %)
351 [[image:FX5U 串口选型号.png]]
352
353 PLC Default Parameters: 
354 [Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
355
356 (% style="text-align:center" %)
357 [[image:FX5U 以太网配置.png]]
358
359 [External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
360
361 (% style="text-align:center" %)
362 [[image:1.3.2.png]]
363
364 PC and PLC connection
365
366 [Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
367
368 (% style="text-align:center" %)
369 [[image:FX5U 以太网连接PLC.png]]
370
371 Downloading PLC project
372 [Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
373
374 (% style="text-align:center" %)
375 [[image:FX5U以太网下载.png]]
376
377 **Cable Wiring**
378
379 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
380
381 == **L02 Serial ** ==
382
383 Mitsubishi L02 series CPU built-in serial port.
384
385 **V-BOX Settings**
386
387 |**Item**|**Settings**|**Note**
388 |Protocol|Mitsubishi L02|
389 |Connection|RS422|
390 |Baud rate|115200|
391 |Data bit|8|
392 |Parity|Odd|
393 |Stop bit|1|
394 |PLC station No.|1~~255|Need to be the same as PLC settings
395
396 (% style="text-align:center" %)
397 [[image:三菱 L02串口协议配置.png]]
398
399 **Address List**
400
401 |**Type**|**Device registers**|**Format**|**Range**|**Note**
402 |(% colspan="1" rowspan="20" %)Bit
403 |X|X h|0~~FFFF|
404 |Y|Y h|0~~FFFF|
405 |M|M d|0~~9999|
406 |L|L d|0~~9999|
407 |F|F d|0~~9999|
408 |B|B h|0~~FFFF|
409 |V|V d|0~~2047|
410 |TC|TC d|0~~9999|
411 |SS|SS d|0~~9999|
412 |SC|SC d|0~~9999|
413 |CS|CS d|0~~9999|
414 |CC|CC d|0~~9999|
415 |SB|SB h|0~~FFFF|
416 |SM|SM d|0~~2047|
417 |STS|STS d|0~~1023|
418 |S|S d|0~~9999|
419 |DX|DX h|0~~FFFF|
420 |DY|DY h|0~~FFFF|
421 |TS|TS d|0~~9999|
422 |Dbit|Dbit d.d|0~~99999.0~~15|
423 |(% colspan="1" rowspan="9" %)Word
424 |W|W h|0~~FFFF|
425 |TN|TN d|0~~99999|
426 |SN|SN d|0~~99999|
427 |CN|CN d|0~~99999|
428 |R|R d|0~~99999|
429 |SW|SW h|0~~FFFF|
430 |Z|Z d|0~~99999|
431 |ZR|ZR h|0~~FFFF|
432 |D|D d|0~~99999|
433
434 **Cable Wiring**
435
436 **RS422**
437
438 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png||alt="image-20220825161612-8.png" height="278" width="612"]]
439
440 [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png||alt="image-20220825160820-4.png" height="208" width="359"]]
441
442 == **L02 Ethernet ** ==
443
444 Mitsubishi L series CPU built-in Ethernet port.
445
446 **V-BOX Settings**
447
448 |**Items**|**Settings**|**Note**
449 |Protocol|MIT L02 CPU MELSEC|
450 |Connection|Ethernet|
451 |Port No.|1025|Must be the same as the PLC setting
452 |PLC station No.|0|Must be the same as the PLC setting
453
454 (% style="text-align:center" %)
455 [[image:三菱 L02以太网协议配置1.png]]
456
457 **PLC Settings (GX Works2 )**
458
459 Create a project
460
461 Set PLC IP, subnet mask and gateway;
462
463 Select [Binary Code] as communication data code;
464
465 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1||alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
466
467 Set PLC port number, for example 1025
468
469 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1||alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
470
471 Save settings;
472
473 Download project into PLC device;
474
475 Restart PLC device;
476
477 **Cable Wiring**
478
479 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
480
481 == {{id name="HQ12HSerial"/}}**Q12H Serial ** ==
482
483 This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
484
485 **[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]**
486
487 == **QJ71E71 Ethernet ** ==
488
489 Mitsubishi QJ71E71 Ethernet communication module;
490
491 **V-BOX Settings**
492
493 |**Items**|**Settings**|**Note**
494 |Protocol|MIT QJ71E71 MELSEC|
495 |Connection|Ethernet|
496 |Port No.|1025|Must be the same as the PLC setting
497 |PLC station No.|0|Must be the same as the PLC setting
498
499 (% style="text-align:center" %)
500 [[image:三菱 QJ71 以太网协议配置.png]]
501
502 **Address List**
503
504 |**Type**|**Device registers**|**Format**|**Range**|**Note**
505 |(% rowspan="18" %)Bit|X|X h|0~~1FFF|
506 |Y|Y h|0~~1FFF|
507 |M|M d|0~~99999|
508 |L|L d|0~~8191|
509 |F|F d|0~~2047|
510 |B|B h|0~~1FFF|
511 |V|V d|0~~2047|
512 |TS|TS d|0~~2047|
513 |TC|TC d|0~~2047|
514 |SS|SS d|0~~2047|
515 |SC|SC d|0~~2047|
516 |CS|CS d|0~~1023|
517 |CC|CC d|0~~1023|
518 |SB|SB h|0~~7FF|
519 |S|S d|0~~8191|
520 |DX|DX h|0~~1FFF|
521 |DY|DY h|0~~1FFF|
522 |SM|SM d|8000~~9999|
523 |(% rowspan="10" %)Word|SD|SD d|0~~2047|
524 |D|D d|0~~12287|
525 |W|W h|0~~1FFF|
526 |TN|TN d|0~~2047|
527 |SN|SN d|0~~2047|
528 |CN|CN d|0~~1023|
529 |R|R d|0~~32767|
530 |SW|SW h|0~~7FF|
531 |Z|Z d|0~~15|
532 |ZR|ZR h|0~~FE7FF|
533
534 **PLC Settings(GX Works2)**
535
536 * Click [Ethernet/CC IE/MELSECNET];
537 * Please select [Ethernet] as network type;
538 * Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
539 * Select [Online] as Mode;
540 * [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png||alt="image-20221119171343-2.png" height="341" width="587"]]
541 * Click [Operation setting] to set IP;
542 * Select [Binary Code] as [Communication Data Code];
543 * [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png||alt="image-20221119171436-3.png" height="354" width="588"]]
544 * Click [Open setting]
545 * Set protocol: TCP;
546 * Set [unpassive] in [Open system];
547 * Set [receive] in [Fixed buffer];
548 * Set [procedure Exist] in [Fixed buffer communication];
549 * Disable [Pairing open];
550 * Set [No confirm] in [Existence confirmation];
551 * Host station port number: 5009;
552 * Save settings;
553 * {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png||alt="image-20221119171611-4.png" height="354" width="588"]]
554 * Download project into PLC and restart it
555
556 **Cable Wiring**
557
558 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
559
560 == Q03UDV ==
561
562 Mitsubishi Q03UDV
563
564 **V-BOX Settings**
565
566 |**Items**|**Settings**|**Note**
567 |Protocol|MIT L02 CPU MELSEC PROTOCOL|
568 |Connection|Ethernet|
569 |Port No.|1025|Must be the same as the PLC setting
570 |PLC station No.|0|Must be the same as the PLC setting
571
572 [[image:1709779590561-640.png]]
573
574 **Address List**
575
576 |**Type**|**Device registers**|**Format**|**Range**|**Note**
577 |(% colspan="1" rowspan="18" %)Bit|X|X h|0~~1fff|
578 |Y|Y h|0~~1fff|
579 |SM|SM d|0~~2047|
580 |M|M d|0~~99999|
581 |L|L d|0~~8191|
582 |F|F d|0~~2047|
583 |V|V d|0~~2047|
584 |B|B h|0~~1fff|
585 |TS|TS d|0~~2047|
586 |TC|TC d|0~~2047|
587 |SS|SS d|0~~2047|
588 |SC|SC d|0~~2047|
589 |CS|CS d|0~~1023|
590 |CC|CC d|0~~1023|
591 |SB|SB h|0~~7ff|
592 |S|S d|0~~8191|
593 |DX|DX h|0~~1fff|
594 |DY|DY h|0~~1fff|
595 |(% colspan="1" rowspan="10" %)Word|SD|SD d|0~~2047|
596 |D|D d|0~~12287|
597 |W|W h|0~~1fff|
598 |TN|TN d|0~~2047|
599 |SN|SN d|0~~2047|
600 |CN|CN d|0~~1023|
601 |SW|SW h|0~~7ff|
602 |Z|Z d|0~~15|
603 |R|R d|0~~32767|
604 |ZR|ZR h|0~~fe7ff|
605
606 (% class="wikigeneratedid" id="HPLCSettings" %)
607 **PLC Settings(GX Works2)**
608
609 (% class="wikigeneratedid" %)
610 PC and PLC connection:
611
612 * Online→Read from PLC
613
614 (% style="text-align:center" %)
615 [[image:1.png]]
616
617 * choose PLC Series→OK
618
619 (% style="text-align:center" %)
620 [[image:StqCG53paq.png]]
621
622 * serial USB→OK
623
624 (% style="text-align:center" %)
625 [[image:Y7H80eq2Eb.png]]
626
627 * Choose Parameter、Global Device Comment and Device Memory→Execute
628
629 (% style="text-align:center" %)
630 [[image:6PAsdFz58I.png]]
631
632 * OK→wait loading successfully→Close
633
634 (% style="text-align:center" %)
635 [[image:0GBGUNn4hQ.png]]
636
637 * Navigation→Parameter→PLC Parameter→IP Address Setting→Built-in Ethernet Port Setting→Host Station(Same as the port on  V-box)→End
638
639 (% style="text-align:center" %)
640 [[image:Ypyl4SUHcf.png]]
641
642 * Debug→Start/ Stop Simulation→wait loading successfully→Close
643
644 (% style="text-align:center" %)
645 [[image:ZmUzFbS39y.png]]
646
647 (% style="text-align:center" %)
648 [[image:ehoO3C6bry.png]]
649
650 (% id="cke_bm_1296534S" style="display:none" %)** **(%%)**Cable Wiring**
651
652 [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]