Wiki source code of Mitsubishi

Last modified by Joe on 2024/05/21 10:53

version	line-number	content
40.1	1	== FX3U,3G,3GA Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	4
38.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
58.1	16	(% style="text-align:center" %)
	17	[[image:三菱 FX3U 串口协议配置.png]]
	18
38.1	19	Address List
2.1	20
67.1	21	\|Type\|Device registers\|Format\|Range\|Note
83.16	22	\|(% rowspan="7" %)Bit\|X\|X o\|0~~303237\|
67.1	23	\|Y\|Y o\|0~~303237\|
	24	\|M\|M d\|0~~99999\|
	25	\|T\|T d\|0~~99999\|
	26	\|C\|C d\|0~~99999\|
	27	\|S\|S d\|0~~99999\|
	28	\|SM\|SM d\|8000~~9999\|
83.16	29	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
67.1	30	\|Y\|Y o\|0~~303237\|
	31	\|M\|M d\|0~~99999\|
	32	\|T\|T d\|0~~99999\|
	33	\|C\|C d\|0~~199\|
	34	\|D\|D d\|0~~7999\|
	35	\|S\|S d\|0~~99999\|
	36	\|SD\|SD d\|8000~~9999\|
2.1	37
42.1	38	PLC Setting
2.1	39
42.1	40	Open GX Works2, create a new PLC project or open the project that has been created.
	41	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	42
	43	(% style="text-align:center" %)
77.1	44	[[image:GX2.png]]
	45
	46	(% style="text-align:center" %)
42.1	47	[[image:1.2.png]]
	48
	49	PLC Default Parameters:
	50	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	51	Note:The serial port parameters should be set depending on field requirements
	52
	53	PC and PLC connection:
	54
	55	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	56
	57	(% style="text-align:center" %)
	58	[[image:1.5.1.png]]
	59
	60	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	61
	62	(% style="text-align:center" %)
	63	[[image:1.5.2.png]]
	64
77.1	65	[PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
	66
	67	(% style="text-align:center" %)
78.1	68	[[image:FX3U串口下载.png]]
77.1	69
42.1	70	Cable Wiring
	71
38.1	72	RS422
2.1	73
38.1	74	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	75
38.1	76	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	77
43.1	78	== FX NOPROTOCOL ==
	79
	80	Mitsubishi FX3G-RS232-BD
	81
	82	V-Box Settings
	83
	84	\|=Item\|=Settings\|=Note
	85	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	86	\|Connection\|RS232\|
	87	\|Baud rate\|9600\|
	88	\|Data bit\|7\|
	89	\|Parity\|EVEN\|
	90	\|Stop bit\|1\|
	91	\|PLC station No.\|0\|
	92
	93	(% style="text-align:center" %)
	94	[[image:三菱 FN盒子通讯配置.png]]
	95
	96	Address List
	97
68.1	98	\|=Type\|=Device registers\|=Format\|=Range\|=Note
	99	\|(% rowspan="8" %)Bit\|X\|X o\|0~~303237\|
	100	\|Y\|Y o\|0~~303237\|
	101	\|M\|M d\|0~~99999\|
	102	\|T\|T d\|0~~99999\|
	103	\|C\|C d\|0~~99999\|
	104	\|S\|S d\|0~~99999\|
	105	\|SM\|SM d\|8000~~9999\|
	106	\|Lamp\|Lamp d\|0~~0\|
	107	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
	108	\|Y\|Y o\|0~~303237\|
	109	\|M\|M d\|0~~99999\|
	110	\|T\|T d\|0~~99999\|
	111	\|C\|C d\|0~~199\|
	112	\|D\|D d\|0~~7999\|
	113	\|S\|S d\|0~~99999\|
	114	\|SD\|SD d\|8000~~9999\|
43.1	115
45.1	116	Cable Wiring
43.1	117
44.1	118	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	119
41.1	120	== FX3U Ethernet ==
2.1	121
	122	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	123
41.1	124	V-BOX Settings
2.1	125
	126	\|Items\|Settings\|Note
	127	\|Protocol\|Mitsubishi FX3U\|
	128	\|Connection\|Ethernet\|
	129	\|Port No.\|5009\|Must be the same as the PLC setting
	130	\|PLC station No.\|0\|
	131
60.1	132	(% style="text-align:center" %)
	133	[[image:三菱 FX3U 以太网协议配置.png]]
57.1	134
41.1	135	Address List
2.1	136
69.1	137	\|Type\|Device registers\|Format\|Range\|Note
	138	\|(% rowspan="7" %)Bit\|X\|X OOO\|0~~377\|
	139	\|Y\|Y OOO\|0~~377\|
	140	\|M\|M DDDD\|0~~7679\|
	141	\|SM\|SM DDDD\|8000~~8511\|
	142	\|S\|S DDDD\|0~~4095\|
	143	\|TS\|TS DDD\|0~~511\|
	144	\|CS\|CS DDD\|0~~255\|
	145	\|(% rowspan="5" %)Word\|CN\|CN DDD\|0~~199\|
	146	\|TN\|TN DDD\|0~~511\|
	147	\|D\|D DDDD\|0~~7999\|
	148	\|SD\|SD DDDD\|8000~~8511\|
	149	\|R\|R DDDDD\|0~~32767\|
2.1	150
41.1	151	Ethernet Module Settings
2.1	152
	153	FX3U-ENET-L module configuration
	154	Set up the FX3U-ENET-L Ethernet module settings as follows.
	155	Select the module location, which in this document is Module 0.
	156
41.1	157	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	158
	159	Select "Operational setting" to enter the following screen.
	160
	161	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
86.2	162
2.1	163
83.18	164	(% style="text-align:center" %)
86.2	165	[[image:Inku25HyY8.png]]
2.1	166
	167	Select "Open setting" to enter the setting interface, the settings are as follows.
	168
	169	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	170
	171	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	172
41.1	173	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	174
85.1	175	(% class="box infomessage" %)
	176	(((
86.1	177	Note: If you can't communicate PLC to box normally, changing ''No confirm" to "confirm"
85.1	178	)))
	179
2.1	180	Click on "transter setup" - "PC side I/F setting", see the following figure.
	181
	182	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	183
	184	use the IP set in the "Ethernet board" to communicate directly with the network cable.
86.2	185
2.1	186
83.18	187	(% style="text-align:center" %)
86.2	188	[[image:WstTyoGrxG.png]]
2.1	189
83.18	190	(% style="text-align:center" %)
86.2	191	[[image:aak9XC8xDH.png]]
2.1	192
83.18	193
	194
41.1	195	PLC Settings (GX Works 2)
2.1	196
	197	Create a blank FX5U project
	198
	199	Find Current Connection in the navigation
	200
41.1	201	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	202
	203	Select Connection Channel List
	204
	205	Select Ethernet board communication
	206
41.1	207	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	208
	209	Select Ethernet Module
	210	Set the IP address of the PLC
	211
41.1	212	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	213
	214	Read or write PLC data, in this document is read
	215
	216	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	217
41.1	218	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	219
46.1	220	== FX5U Serial ==
2.1	221
	222	Mitsubishi FX5U series PLC
	223
46.1	224	V-BOX Settings
2.1	225
	226	\|Item\|Settings\|Note
	227	\|Protocol\|Mitsubishi FX5U\|
	228	\|Connection\|RS422/RS485\|
	229	\|Baud rate\|9600\|
	230	\|Data bit\|7\|
	231	\|Parity\|Odd\|
	232	\|Stop bit\|1\|
	233	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	234
54.1	235	(% style="text-align:center" %)
	236	[[image:三菱 FX5U 串口协议配置.png]]
	237
46.1	238	Address List
2.1	239
70.1	240	\|Type\|Device registers\|Format\|Range\|Note
	241	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	242	\|Y\|Y o\|0~~303237\|
	243	\|M\|M d\|0~~99999\|
	244	\|B\|B h\|0~~7FFF\|
	245	\|F\|F d\|0~~32767\|
	246	\|SB\|SB h\|0~~7FFF\|
	247	\|TS\|TS d\|0~~1023\|
	248	\|TC\|TC d\|0~~1023\|
	249	\|STS\|STS d\|0~~1023\|
	250	\|STC\|STS d\|0~~1023\|
	251	\|CS\|CS d\|0~~1023\|
	252	\|CC\|CC d\|0~~1023\|
	253	\|SM\|SM d\|0~~9999\|
	254	\|L\|L d\|0~~32767\|
	255	\|S\|S d\|0~~4095\|
	256	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	257	\|TN\|TN d\|0~~1023\|
	258	\|STN\|STN d\|0~~1023\|
	259	\|CN\|CN d\|0~~1023\|
	260	\|R\|R d\|0~~32767\|
	261	\|SW\|SW h\|0~~7FFF\|
	262	\|Z\|Z d\|0~~23\|
	263	\|D\|D d\|0~~7999\|
	264	\|SD\|SD d\|0~~11999\|
2.1	265
79.1	266	PLC Settings
2.1	267
	268	Create a blank FX5U project
	269
79.1	270	Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
2.1	271
79.1	272	(% style="text-align:center" %)
	273	[[image:GX3.png]]
2.1	274
	275
79.1	276	(% style="text-align:center" %)
	277	[[image:FX5U 串口选型号.png]]
2.1	278
79.1	279	PLC Default Parameters:
	280	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
2.1	281
79.1	282	(% style="text-align:center" %)
	283	[[image:FX5U plc串口参数配置.png]]
2.1	284
	285
79.1	286	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
2.1	287
79.1	288	{{info}}
	289	✎Note: The serial port parameters should be set depending on field requirements.
	290	{{/info}}
2.1	291
79.1	292	(% style="text-align:center" %)
	293	[[image:FX5U plc串口参数.png]]
2.1	294
46.1	295	Cable Wiring
2.1	296
46.1	297	RS422
2.1	298
80.1	299	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
2.1	300
80.1	301	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
2.1	302
33.1	303	== FX5U Ethernet ==
2.1	304
	305	Mitsubishi FX5U series PLC
	306
59.1	307	V-BOX Settings
2.1	308
	309	\|Items\|Settings\|Note
	310	\|Protocol\|Mitsubishi FX5U\|
	311	\|Connection\|Ethernet\|
	312	\|Port No.\|5002\|Must be the same as the PLC setting
	313	\|PLC station No.\|0\|
	314
59.1	315	(% style="text-align:center" %)
	316	[[image:三菱 FX5U 以太网协议配置.png]]
2.1	317
59.1	318	Address List
	319
71.1	320	\|Type\|Device registers\|Format\|Range\|Note
	321	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	322	\|Y\|Y o\|0~~303237\|
	323	\|M\|M d\|0~~99999\|
	324	\|B\|B h\|0~~7FFF\|
	325	\|F\|F d\|0~~32767\|
	326	\|SB\|SB h\|0~~7FFF\|
	327	\|TS\|TS d\|0~~1023\|
	328	\|TC\|TC d\|0~~1023\|
	329	\|STS\|STS d\|0~~1023\|
	330	\|STC\|STS d\|0~~1023\|
	331	\|CS\|CS d\|0~~1023\|
	332	\|CC\|CC d\|0~~1023\|
	333	\|SM\|SM d\|0~~9999\|
	334	\|L\|L d\|0~~32767\|
	335	\|S\|S d\|0~~4095\|
	336	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	337	\|TN\|TN d\|0~~1023\|
	338	\|STN\|STN d\|0~~1023\|
	339	\|CN\|CN d\|0~~1023\|
	340	\|R\|R d\|0~~32767\|
	341	\|SW\|SW h\|0~~7FFF\|
	342	\|Z\|Z d\|0~~23\|
	343	\|D\|D d\|0~~7999\|
	344	\|SD\|SD d\|0~~11999\|
2.1	345
81.1	346	PLC Settings
2.1	347
81.1	348	Open GX Works3, create a new PLC project or open the project that has been created.
	349
	350	Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
	351
75.2	352	(% style="text-align:center" %)
81.1	353	[[image:GX3.png]]
2.1	354
81.1	355	(% style="text-align:center" %)
	356	[[image:FX5U 串口选型号.png]]
	357
	358	PLC Default Parameters:
	359	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
	360
	361	(% style="text-align:center" %)
	362	[[image:FX5U 以太网配置.png]]
	363
75.2	364	[External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
2.1	365
75.2	366	(% style="text-align:center" %)
	367	[[image:1.3.2.png]]
2.1	368
81.1	369	PC and PLC connection
	370
	371	[Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
	372
	373	(% style="text-align:center" %)
	374	[[image:FX5U 以太网连接PLC.png]]
	375
	376	Downloading PLC project
	377	[Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
	378
	379	(% style="text-align:center" %)
	380	[[image:FX5U以太网下载.png]]
	381
59.1	382	Cable Wiring
2.1	383
33.1	384	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	385
47.1	386	== L02 Serial ==
2.1	387
	388	Mitsubishi L02 series CPU built-in serial port.
	389
47.1	390	V-BOX Settings
2.1	391
	392	\|Item\|Settings\|Note
	393	\|Protocol\|Mitsubishi L02\|
	394	\|Connection\|RS422\|
	395	\|Baud rate\|115200\|
	396	\|Data bit\|8\|
	397	\|Parity\|Odd\|
	398	\|Stop bit\|1\|
	399	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	400
53.1	401	(% style="text-align:center" %)
	402	[[image:三菱 L02串口协议配置.png]]
	403
47.1	404	Address List
2.1	405
72.1	406	\|Type\|Device registers\|Format\|Range\|Note
47.1	407	\|(% colspan="1" rowspan="20" %)Bit
72.1	408	\|X\|X h\|0~~FFFF\|
	409	\|Y\|Y h\|0~~FFFF\|
	410	\|M\|M d\|0~~9999\|
	411	\|L\|L d\|0~~9999\|
	412	\|F\|F d\|0~~9999\|
	413	\|B\|B h\|0~~FFFF\|
	414	\|V\|V d\|0~~2047\|
	415	\|TC\|TC d\|0~~9999\|
	416	\|SS\|SS d\|0~~9999\|
	417	\|SC\|SC d\|0~~9999\|
	418	\|CS\|CS d\|0~~9999\|
	419	\|CC\|CC d\|0~~9999\|
	420	\|SB\|SB h\|0~~FFFF\|
	421	\|SM\|SM d\|0~~2047\|
	422	\|STS\|STS d\|0~~1023\|
	423	\|S\|S d\|0~~9999\|
	424	\|DX\|DX h\|0~~FFFF\|
	425	\|DY\|DY h\|0~~FFFF\|
	426	\|TS\|TS d\|0~~9999\|
	427	\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
47.1	428	\|(% colspan="1" rowspan="9" %)Word
72.1	429	\|W\|W h\|0~~FFFF\|
	430	\|TN\|TN d\|0~~99999\|
	431	\|SN\|SN d\|0~~99999\|
	432	\|CN\|CN d\|0~~99999\|
	433	\|R\|R d\|0~~99999\|
	434	\|SW\|SW h\|0~~FFFF\|
	435	\|Z\|Z d\|0~~99999\|
	436	\|ZR\|ZR h\|0~~FFFF\|
	437	\|D\|D d\|0~~99999\|
2.1	438
47.1	439	Cable Wiring
2.1	440
47.1	441	RS422
2.1	442
47.1	443	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
2.1	444
47.1	445	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
2.1	446
48.1	447	== L02 Ethernet ==
2.1	448
	449	Mitsubishi L series CPU built-in Ethernet port.
	450
48.1	451	V-BOX Settings
2.1	452
	453	\|Items\|Settings\|Note
	454	\|Protocol\|MIT L02 CPU MELSEC\|
	455	\|Connection\|Ethernet\|
	456	\|Port No.\|1025\|Must be the same as the PLC setting
	457	\|PLC station No.\|0\|Must be the same as the PLC setting
	458
52.1	459	(% style="text-align:center" %)
	460	[[image:三菱 L02以太网协议配置1.png]]
51.1	461
48.1	462	PLC Settings (GX Works2 )
2.1	463
	464	Create a project
	465
	466	Set PLC IP, subnet mask and gateway;
	467
	468	Select [Binary Code] as communication data code;
	469
49.1	470	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
2.1	471
	472	Set PLC port number, for example 1025
	473
49.1	474	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
2.1	475
	476	Save settings;
	477
	478	Download project into PLC device;
	479
	480	Restart PLC device;
	481
49.1	482	Cable Wiring
2.1	483
49.1	484	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	485
	486	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	487
	488	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	489
	490	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	491
32.1	492	== QJ71E71 Ethernet ==
2.1	493
	494	Mitsubishi QJ71E71 Ethernet communication module;
	495
50.1	496	V-BOX Settings
2.1	497
	498	\|Items\|Settings\|Note
	499	\|Protocol\|MIT QJ71E71 MELSEC\|
	500	\|Connection\|Ethernet\|
	501	\|Port No.\|1025\|Must be the same as the PLC setting
	502	\|PLC station No.\|0\|Must be the same as the PLC setting
	503
61.1	504	(% style="text-align:center" %)
	505	[[image:三菱 QJ71 以太网协议配置.png]]
2.1	506
50.1	507	Address List
	508
74.1	509	\|Type\|Device registers\|Format\|Range\|Note
	510	\|(% rowspan="18" %)Bit\|X\|X h\|0~~1FFF\|
	511	\|Y\|Y h\|0~~1FFF\|
	512	\|M\|M d\|0~~99999\|
	513	\|L\|L d\|0~~8191\|
	514	\|F\|F d\|0~~2047\|
	515	\|B\|B h\|0~~1FFF\|
	516	\|V\|V d\|0~~2047\|
	517	\|TS\|TS d\|0~~2047\|
	518	\|TC\|TC d\|0~~2047\|
	519	\|SS\|SS d\|0~~2047\|
	520	\|SC\|SC d\|0~~2047\|
	521	\|CS\|CS d\|0~~1023\|
	522	\|CC\|CC d\|0~~1023\|
	523	\|SB\|SB h\|0~~7FF\|
	524	\|S\|S d\|0~~8191\|
	525	\|DX\|DX h\|0~~1FFF\|
	526	\|DY\|DY h\|0~~1FFF\|
	527	\|SM\|SM d\|8000~~9999\|
	528	\|(% rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
	529	\|D\|D d\|0~~12287\|
	530	\|W\|W h\|0~~1FFF\|
	531	\|TN\|TN d\|0~~2047\|
	532	\|SN\|SN d\|0~~2047\|
	533	\|CN\|CN d\|0~~1023\|
	534	\|R\|R d\|0~~32767\|
	535	\|SW\|SW h\|0~~7FF\|
	536	\|Z\|Z d\|0~~15\|
	537	\|ZR\|ZR h\|0~~FE7FF\|
2.1	538
50.1	539	PLC Settings(GX Works2)
2.1	540
	541	* Click [Ethernet/CC IE/MELSECNET];
	542	* Please select [Ethernet] as network type;
	543	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	544	* Select [Online] as Mode;
50.1	545	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
2.1	546	* Click [Operation setting] to set IP;
	547	* Select [Binary Code] as [Communication Data Code];
50.1	548	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
2.1	549	* Click [Open setting]
	550	* Set protocol: TCP;
	551	* Set [unpassive] in [Open system];
	552	* Set [receive] in [Fixed buffer];
	553	* Set [procedure Exist] in [Fixed buffer communication];
	554	* Disable [Pairing open];
	555	* Set [No confirm] in [Existence confirmation];
	556	* Host station port number: 5009;
	557	* Save settings;
	558	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	559	* Download project into PLC and restart it
	560
50.1	561	Cable Wiring
2.1	562
34.1	563	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
83.2	564
	565	== Q03UDV ==
83.3	566
	567	Mitsubishi Q03UDV
	568
	569	V-BOX Settings
	570
83.4	571	\|Items\|Settings\|Note
83.7	572	\|Protocol\|MIT L02 CPU MELSEC PROTOCOL\|
83.4	573	\|Connection\|Ethernet\|
83.5	574	\|Port No.\|1025\|Must be the same as the PLC setting
83.6	575	\|PLC station No.\|0\|Must be the same as the PLC setting
83.7	576
83.8	577	[[image:1709779590561-640.png]]
	578
	579	Address List
	580
	581	\|Type\|Device registers\|Format\|Range\|Note
	582	\|(% colspan="1" rowspan="18" %)Bit\|X\|X h\|0~~1fff\|
	583	\|Y\|Y h\|0~~1fff\|
	584	\|SM\|SM d\|0~~2047\|
	585	\|M\|M d\|0~~99999\|
	586	\|L\|L d\|0~~8191\|
	587	\|F\|F d\|0~~2047\|
	588	\|V\|V d\|0~~2047\|
	589	\|B\|B h\|0~~1fff\|
	590	\|TS\|TS d\|0~~2047\|
	591	\|TC\|TC d\|0~~2047\|
	592	\|SS\|SS d\|0~~2047\|
	593	\|SC\|SC d\|0~~2047\|
	594	\|CS\|CS d\|0~~1023\|
	595	\|CC\|CC d\|0~~1023\|
	596	\|SB\|SB h\|0~~7ff\|
	597	\|S\|S d\|0~~8191\|
	598	\|DX\|DX h\|0~~1fff\|
	599	\|DY\|DY h\|0~~1fff\|
83.9	600	\|(% colspan="1" rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
83.8	601	\|D\|D d\|0~~12287\|
	602	\|W\|W h\|0~~1fff\|
	603	\|TN\|TN d\|0~~2047\|
	604	\|SN\|SN d\|0~~2047\|
	605	\|CN\|CN d\|0~~1023\|
	606	\|SW\|SW h\|0~~7ff\|
	607	\|Z\|Z d\|0~~15\|
	608	\|R\|R d\|0~~32767\|
	609	\|ZR\|ZR h\|0~~fe7ff\|
83.10	610
83.12	611	(% class="wikigeneratedid" id="HPLCSettings" %)
	612	PLC Settings(GX Works2)
	613
	614	(% class="wikigeneratedid" %)
	615	PC and PLC connection:
	616
83.15	617	* Online→Read from PLC
83.12	618
	619	(% style="text-align:center" %)
	620	[[image:1.png]]
	621
83.15	622	* choose PLC Series→OK
83.14	623
83.12	624	(% style="text-align:center" %)
	625	[[image:StqCG53paq.png]]
	626
83.15	627	* serial USB→OK
83.14	628
83.12	629	(% style="text-align:center" %)
	630	[[image:Y7H80eq2Eb.png]]
	631
83.15	632	* Choose Parameter、Global Device Comment and Device Memory→Execute
83.14	633
83.12	634	(% style="text-align:center" %)
	635	[[image:6PAsdFz58I.png]]
	636
83.15	637	* OK→wait loading successfully→Close
83.14	638
83.13	639	(% style="text-align:center" %)
	640	[[image:0GBGUNn4hQ.png]]
	641
83.15	642	* Navigation→Parameter→PLC Parameter→IP Address Setting→Built-in Ethernet Port Setting→Host Station(Same as the port on V-box)→End
83.14	643
83.13	644	(% style="text-align:center" %)
	645	[[image:Ypyl4SUHcf.png]]
	646
83.15	647	* Debug→Start/ Stop Simulation→wait loading successfully→Close
83.14	648
83.13	649	(% style="text-align:center" %)
	650	[[image:ZmUzFbS39y.png]]
	651
	652	(% style="text-align:center" %)
	653	[[image:ehoO3C6bry.png]]
	654
83.15	655	(% id="cke_bm_1296534S" style="display:none" %) (%%)Cable Wiring
	656
	657	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents