Xinje

Last modified by Theodore Xu on 2023/11/06 10:28

XC serial

Support Series: Xinjie XC Series

V-Box Settings

Item	Settings	Note
Protocol	XINJE XC MODBUS
Connection	RS232
Baud rate	19200
Data bit	8
Parity	EVEN
Stop bit	1
PLC station No.	1

Address List

Type	Device registers	HMI registers	Format	Range	Note
Bit	M	M	M d	0~8511
Bit	X	X	X o	0~1747
Bit	Y	Y	Y o	0~1747
Bit	S	S	S d	0~1023
Bit	T	T	T d	0~4095
Bit	C	C	C d	0~634
Word	D	D	D d	0~8511
Word	TD	TD	TD d	0~618
Word	CD	CD	CD d	0~634
Word	FD	FD	FD d	0~8511

PLC Settings

Create the new project, and select the specific model according to the actual PLC

Program the PLC

Connect PLC with PC through RS232-USB converter cable. Click [Option]-[Software Serial Port Config] to open the software connection setup window, and select the serial port, if the red text prompt "Connect To PLC Succeeded", which means the connection is setup successfully, then click OK to save the settings.

Change the PLC communication setup if required. Double click the tree node [PLC Serial Port] from Project tree. And change Modbus parameters, then click [Write to PLC] and OK to finish.

Click [Online]-[Download Program] to download program into PLC. And the download pop up window would pop up, then click OK.

Cable Wiring

Figure

Pin Definition Diagram

XD serial

V-Box Settings

Supported Series: Xinjie XD/XE Series PLC

Item	Settings	Note
Protocol	XINJE XD/XC MODBUS
Connection	RS232
Baud rate	19200
Data bit	8
Parity	EVEN
Stop bit	1
PLC station No.	1

Address List

Type	Device registers	HMI registers	Format	Range	Note
Bit	M	M	M d	0~74999
Bit	X1xx	X1xx	X1xx o	0~1177
Bit	X2xx	X2xx	X2xx o	0~277
Bit	X	X	X o	0~77
Bit	Y1xx	Y1xx	Y1xx o	0~1177
Bit	Y2xx	Y2xx	Y2xx o	0~277
Bit	Y	Y	Y o	0~4095
Bit	SM	SM	SM d	0~4999
Bit	T	T	T d	0~4999
Bit	C	C	C d	0~4999
Bit	ET	ET	ET d	0~31
Bit	SE	SE	SE d	0~31
Bit	HM	HM	HM d	0~11999
Bit	HSC	HSC	HSC d	0~39
Bit	HS	HS	HS d	0~999
Bit	HT	HT	HT d	0~1999
Bit	HC	HC	HC d	0~1999
Bit	S	S	S d	0~7999
Word	D	D	D d	0~69999
Word	ID	ID	ID d	0~99
Word	ID1xx	ID1xx	ID1xx d	0~999
Word	ID2xx	ID2xx	ID2xx d	0~299
Word	QD	QD	QD d	0~99
Word	QD1xx	QD1xx	QD1xx d	0~999
Word	QD2xx	QD2xx	QD2xx d	0~299
Word	SD	SD	SD d	0~4999
Word	TD	TD	TD d	0~575
Word	CD	CD	CD d	0~575
Word	ETD	ETD	ETD d	0~31
Word	HD	HD	HD d	0~24999
Word	HSD	HSD	HSD d	0~1023
Word	HTD	HTD	HTD d	0~95
Word	HCD	HCD	HCD d	0~95
Word	HSCD	HSCD	HSCD d	0~31
Word	FD	FD	FD d	0~8191
Word	SFD	SFD	SFD d	0~5999
Word	FS	FS	FS d	0~47

PLC Settings

Create the new project, and select the specific model according to the actual PLC

Program the PLC

Connect PLC with PC through RS232-USB converter cable. Click [Option]-[Software Serial Port Config]-[Communication configuration] to open the PC connection configuration.

XinjieXDopenSWcom (1).png

New a Modbus configuration, and Click [Comm-Test] to test connection, if shows "Connect To PLC Succeeded", which means PLC connection set up successfully. And click OK to save the settings.

Remember to click the Status cell of new created Modbus configuration for change the status into "in use", then click OK to exit.

After done the previous steps, it would prompt like the below.

Click [Online]-[Download Program & Data], and wait for a while, the pop up window would ask for whether to stop PLC, and click [Stop PLC, contitue download]