Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 12.1
edited by Ben
on 2022/07/14 14:03
Change comment: There is no comment for this version
To version 35.1
edited by Ben
on 2022/08/24 10:52
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,7 +1,5 @@
1 -= **1 General communication with PLC** =
1 += **Modbus RTU** =
2 2  
3 -== **Modbus RTU** ==
4 -
5 5  === **V-BOX as master** ===
6 6  
7 7  Select the protocol “(% class="mark" %)Modbus RTU Slave(All Fuction)”,
... ... @@ -47,77 +47,295 @@
47 47  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
48 48  |0F (Write multiple bits)
49 49  
50 -== **WECON LX3V PLC** ==
48 += **WECON PLC** =
51 51  
52 -Select the protocol (% class="mark" %)"WECON LX3V"
50 +== **V-BOX 和维控 LX3V 串行通信** ==
53 53  
54 -(% class="mark" %)then set BaudRate,Port,Stop Bit,Data Bit,Parity same with PLC.
52 +Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
55 55  
56 -(% class="mark" %)WECON PLC RS422 port,default communication parameters is 9600,1,7,ZEVEN
54 +**HMI Settings**
57 57  
56 +|**Item**|**Settings**|**Note**
57 +|Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
58 +|Connection|RS422/RS485|
59 +|Baud rate|9600|
60 +|Data bit|7|
61 +|Parity|EVEN|
62 +|Stop bit|1|
63 +|PLC station No.|1|
64 +
65 +**Address List**
66 +
67 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
68 +|(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
69 +|Y|Y|Y o|0~~303237|
70 +|M|M|M d|0~~99999|
71 +|T|T|T d|0~~99999|
72 +|C|C|C d|0~~99999|
73 +|S|S|S d|0~~99999|
74 +|(% rowspan="8" %)Word|X|X|Xo|0~~303237|
75 +|Y|Y|Y o|0~~303237|
76 +|M|M|M d|0~~99999|
77 +|T|T|T d|0~~99999|
78 +|C|C|C d|0~~199|
79 +|D|D|D d|0~~7999|
80 +|S|S|S d|0~~99999|
81 +|SD|SD|SD d|8000~~9999|
82 +
83 +**Cable Wiring**
84 +
85 +* **RS485**
86 +
87 + [[image:image-20220822172124-1.png]]
88 +
89 +* **RS422**
90 +
91 + [[image:image-20220822172228-2.png]]
92 +
93 +
94 +**✎Note:**
95 +
96 +* HMI COM3 is available in PI8000 series and COM3 is in COM2(hardware PIN 7 and PIN 8) .
97 +* If PLC <= 20 points,such as LX3V-1208/LX3V-0806 PLC,PLC RS485A and RS485B mean PLC COM2 RS485+ and RS485- .PLC COM2 can support modbus. Please refer to PLC COM2 setting manual.
98 +
99 +[[https:~~/~~/drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing>>url:https://drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing]]
100 +
101 +
102 +== **V-BOX and Wecon LX5V serial communication** ==
103 +
104 +This example introduces the establishment of serial port communication between Wecon V-BOX and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
105 +
106 +**Software configuration of PLC**
107 +
108 +**1）PLC programming software**
109 +
110 +[[image:image-20220822172553-1.png]]
111 +
112 +**2）New PLC project**
113 +
114 +Click New Project and select the PLC model.
115 +
116 +[[image:image-20220822172623-2.png]]
117 +
118 +**3）Set Serial port parameters**
119 +
120 +Follow the steps below to configure Serial port parameters
121 +
122 +Baud rate：115200
123 +
124 +Data bit：8
125 +
126 +Stop bit：1
127 +
128 +Parity：No verification
129 +
130 +[[image:image-20220822172657-3.png]]
131 +
132 +**4）Registers list**
133 +
134 +[[image:image-20220822172730-4.png]]
135 +
136 +**V-BOX software configuration**
137 +
138 +**1）V-BOX programming software**
139 +
140 + [[image:image-20220824104124-1.png]]
141 +
142 +**2）V-NET add device**
143 +
144 +Open V-NET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the access key, password and remark, to add the device.
145 +
146 +[[image:image-20220824104909-2.png]]
147 +
148 +
149 +**3）Set communication port parameters**
150 +
151 +Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
152 +
153 +Baud rate：115200
154 +
155 +Data bit：8
156 +
157 +Stop bit：1
158 +
159 +Parity：No verification
160 +
161 +[[image:image-20220811104012-1.png]]
162 +
163 +
164 +**hardware connection**
165 +
166 +**1）Hardware wiring diagram**
167 +
168 +This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
169 +
170 +
171 +
172 +[[image:image-20220811103005-4.png]]
173 +
174 +[[image:image-20220811103227-7.png]]
175 +
176 +The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
177 +
178 +== **V-BOX and Wecon LX5V-N Ethernet communication** ==
179 +
180 + This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
181 +
182 +**Software configuration of PLC**
183 +
184 +**1）PLC programming software**
185 +
186 +[[image:image-20220810164710-1.png]]
187 +
188 +**2）New PLC project**
189 +
190 +Click New Project and select the PLC model.
191 +
192 +[[image:image-20220811115454-1.png]]
193 +
194 +**3）Set Ethernet port parameters**
195 +
196 +Follow the steps below to configure Ethernet parameters
197 +
198 +PLC IP address：192.168.39.200
199 +
200 +default gateway：192.168.39.1
201 +
202 +subnet mask：255.255.255.0
203 +
204 +[[image:image-20220811140530-2.png]]
205 +
206 +**4）Registers list**
207 +
208 +[[image:image-20220811102219-3.png]]
209 +
210 +**HMI software configuration**
211 +
212 +**1）HMI programming software**
213 +
214 + [[image:image-20220810171237-4.png]]
215 +
216 +**2）New HMI project**
217 +
218 +Click New Project and select the HMI model.
219 +
220 +[[image:image-20220810172010-5.png]]
221 +
222 +**3）Set communication port parameters**
223 +
224 +Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
225 +
226 +HMI IP address：192.168.39.201
227 +
228 +default gateway：192.168.39.1
229 +
230 +subnet mask：255.255.255.0
231 +
232 +[[image:image-20220811170753-2.png]]
233 +
234 +Next, click Communication Settings to configure the IP of the HMI communication object.
235 +
236 +[[image:image-20220811163047-1.png]]
237 +
238 +**hardware connection**
239 +
240 +**1）Hardware wiring diagram**
241 +
242 +This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
243 +
244 +[[image:image-20220811170248-1.png]]
245 +
246 +The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
247 +
58 58  (% style="text-align:center" %)
59 59  [[image:1624348978863-771.png||queryString="width=812&height=494" height="487" width="800" class="img-thumbnail"]]
60 60  
61 -== ==
251 += **Rockwell PLC** =
62 62  
63 -== **2 Communication with Allen-Bradley CompactLogix L1769** ==
253 +== **Communication with AB CompactLogix L1769** ==
64 64  
65 -=== **Overview** ===
66 -
67 67  (((
256 +(((
68 68  This example introduces the establishment of Ethernet communication between Wecon V-box and Allen-Bradley L1769. It is introduced through three parts: PLC software configuration, V-box software configuration, and hardware wiring.
69 69  )))
70 70  
71 -(((
72 72  
73 73  )))
74 74  
75 75  (((
76 -== **Software configuration of PLC** ==
264 +(% class="wikigeneratedid" id="HSoftwareconfigurationofPLC" %)
265 +(((
266 +**Software configuration of PLC**
267 +)))
77 77  
78 -=== **PLC programming software** ===
269 +(% class="wikigeneratedid" id="HPLCprogrammingsoftware" %)
270 +(((
271 +**1）PLC programming software**
272 +)))
79 79  
80 - [[image:image-20220714113935-3.png]]
274 +[[image:image-20220714162600-1.png]]
81 81  
82 -=== **New PLC project** ===
83 -
276 +(% class="wikigeneratedid" id="HNewPLCproject" %)
84 84  (((
85 -Click New Project and select the PLC model.
278 +**2）New PLC project**
86 86  )))
87 87  
88 88  (((
89 - [[image:image-20220714114247-4.png]]
282 +(((
283 +Click New Project and select the PLC model.
90 90  )))
285 +)))
91 91  
92 92  (((
93 - [[image:image-20220714114257-5.png]]
288 +[[image:image-20220714162617-2.png]]
94 94  )))
95 95  
96 96  (((
97 97  
293 +
294 +[[image:image-20220714162652-4.png]]
98 98  )))
99 99  
100 100  (((
101 -=== **Set Ethernet parameters** ===
298 +(% class="wikigeneratedid" id="HSetEthernetparameters" %)
299 +(((
300 +**3）Set Ethernet parameters**
301 +)))
102 102  
103 103  (((
304 +(((
305 +(((
104 104  Follow the steps below to configure Ethernet parameters
105 105  )))
308 +)))
309 +)))
106 106  
107 107  (((
312 +(((
313 +(((
108 108  PLC IP address：192.168.40.101
109 109  )))
316 +)))
317 +)))
110 110  
111 111  (((
320 +(((
321 +(((
112 112  default gateway：192.168.40.1
113 113  )))
324 +)))
325 +)))
114 114  
115 115  (((
328 +(((
329 +(((
116 116  subnet mask：255.255.255.0
117 117  )))
332 +)))
333 +)))
118 118  
119 119  (((
120 - [[image:image-20220714115012-6.png]]
336 +[[image:image-20220714162713-5.png]]
121 121  )))
122 122  
123 123  (((
... ... @@ -125,67 +125,139 @@
125 125  )))
126 126  
127 127  (((
128 -== **V-box software configuration** ==
344 +(% class="wikigeneratedid" id="HV-boxsoftwareconfiguration" %)
345 +(((
346 +**V-box software configuration**
347 +)))
129 129  
130 -=== **V-box programming software** ===
349 +(% class="wikigeneratedid" id="HV-boxprogrammingsoftware" %)
350 +(((
351 +**1）V-box programming software**
352 +)))
131 131  
132 - [[image:image-20220714115214-7.png]]
354 +(% class="wikigeneratedid" %)
355 +(((
356 + [[image:image-20220714162725-6.png]]
357 +)))
133 133  
359 +(% class="wikigeneratedid" id="HConfiguredevicenetwork" %)
360 +(((
361 +**2）Configure device network**
362 +)))
134 134  
135 -=== **Configure device network** ===
136 -
137 137  (((
365 +(((
366 +(((
138 138  Click the Configuration Download button[[image:image-20220714115308-8.png||height="22" width="15"]], It is used to configure the device network, update the device time, obtain the device machine code, check the device network, etc.
139 139  )))
140 140  
141 141  (((
142 -In the example below, the IP address of V-Box is configured as 192.168.40.66, and the networking method is 4G connection.
371 +In the example below, the IP address of V-Box is configured as 192.168.40.66, and the networking method is 4G connection
143 143  )))
144 -
145 - [[image:image-20220714115440-9.png||height="425" width="791"]]
146 146  )))
147 147  )))
148 148  
149 -== **V-net add device** ==
376 +(((
377 +(((
378 +[[image:image-20220714162737-7.png]]
379 +
380 +
150 150  )))
382 +)))
383 +)))
384 +)))
151 151  
386 +(% class="wikigeneratedid" id="HV-netadddevice" %)
152 152  (((
153 -Open VNET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the device machine code/product code, device password, and device alias to add the device. 
388 +**3）V-net add device**
154 154  )))
390 +)))
155 155  
156 156  (((
157 - [[image:image-20220714115640-10.png||height="430" width="797"]]
393 +(((
394 +Open VNET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the device machine code/product code, device password, and device alias to add the device.   [[image:image-20220714162752-8.png]]
158 158  )))
159 159  
160 -(((
161 161  
162 162  )))
163 163  
164 164  (((
165 -=== **Set communication port parameters** ===
401 +(% class="wikigeneratedid" id="HSetcommunicationportparameters" %)
402 +(((
403 +**4）Set communication port parameters**
404 +)))
166 166  
406 +(((
167 167  In the device list on the left, find the Vbox that communicates with the L1769, click it and select configuration,communication port configuration in the main interface to add a communication protocol.
408 +)))
168 168  
169 - [[image:image-20220714115848-11.png||height="432" width="802"]]
410 +[[image:image-20220714162805-9.png]]
170 170  )))
171 171  
172 -
413 +(((
173 173  The communication port is selected as Ethernet, the device type is selected as Allen-Bradley, the protocol is Allen-BradleyMicro850_FreeTag EthemetIP, and the IP is the internal IP address of the L1769 PLC. The port number is 44818.
415 +)))
174 174  
417 +[[image:image-20220714162814-10.png]]
175 175  
176 176  
177 -== **Siemens S7-1200** ==
420 +(((
421 +After adding the protocol Allen-BradleyMicro850_FreeTag, click[[image:image-20220714143838-2.png]]icon add label.[[image:image-20220714162827-11.png]]
422 +)))
178 178  
179 -[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20S7-1200%20via%20Ehernet.zip]]
424 +(% class="wikigeneratedid" id="HEngineeringproduction" %)
425 +(((
426 +**5）Engineering production**
427 +)))
180 180  
429 +(% class="wikigeneratedid" %)
430 +(((
431 +(((
432 +According to your own needs, use the V-NET client software to edit the required data monitoring points.
433 +)))
434 +
435 +[[image:image-20220714162841-12.png]]
436 +
437 +
438 +(((
439 +**hardware connection**
440 +)))
441 +)))
442 +
443 +(((
444 +**1）Hardware wiring diagram**
445 +)))
446 +
447 +(((
448 +(((
449 +This example introduces Wecon V-box with Allen-Bradley L1769 PLC to establish communication through Ethernet. The connection diagram is as follows:
450 +)))
451 +
452 +[[image:image-20220714162856-13.png]]
453 +
454 +(((
455 +The above are all the steps for establishing Ethernet communication between Wecon V-box with Allen-Bradley L1769 PLC.
456 +
457 +
181 181  == **Allen-Bradley Ethernet DF1** ==
182 182  
183 183  [[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Allen-Bradley%20Ethernet%20DF1.zip]]
184 184  
462 +
463 += **Siemens PLC** =
464 +)))
465 +)))
466 +
467 +== **Siemens S7-1200** ==
468 +
469 +[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20S7-1200%20via%20Ehernet.zip]]
470 +
185 185  == **Communication with S7-200 Smart** ==
186 186  
187 187  [[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20S7-200%20Smart.zip]]
188 188  
475 += **Delta PLC** =
476 +
189 189  == **Delta DVP Ethernet** ==
190 190  
191 191  [[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
... ... @@ -212,7 +212,7 @@
212 212  
213 213  = **2 User define protocol** =
214 214  
215 -More serial port script instruction,please refer manual:[[Lua script function>>doc:V-BOX.V-Net.1\.User Manual.04 Lua Script.01 Lua Functions.WebHome]]~-~-->[[3.Serial port operation>>url:http://docs.we-con.com.cn/wiki/vbox/view/HMI/04.Lua%20script%20%20function%20and%20operation/01.Lua%20script%20function/#H3.Serialportoperation]]
503 +More serial port script instruction,please refer manual:[[Lua script function>>doc:V-BOX.V-Net.Manual.04 Lua Script.01 Lua Functions.WebHome]]~-~-->[[3.Serial port operation>>url:http://docs.we-con.com.cn/wiki/vbox/view/HMI/04.Lua%20script%20%20function%20and%20operation/01.Lua%20script%20function/#H3.Serialportoperation]]
216 216  
217 217  == **Read the temperature sensor.** ==
218 218  
image-20220714143820-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +1.4 MB
Content
image-20220714143838-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +520 bytes
Content
image-20220714143849-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +1.3 MB
Content
image-20220714160006-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +1.3 MB
Content
image-20220714160034-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +135.2 KB
Content
image-20220714160120-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.8 KB
Content
image-20220714160335-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +264.1 KB
Content
image-20220714160412-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.5 KB
Content
image-20220714160439-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +104.0 KB
Content
image-20220714160541-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +13.7 KB
Content
image-20220714160651-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +135.2 KB
Content
image-20220714160843-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +165.9 KB
Content
image-20220714160943-10.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +50.2 KB
Content
image-20220714161014-11.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +94.3 KB
Content
image-20220714161120-12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +94.3 KB
Content
image-20220714161229-13.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +62.5 KB
Content
image-20220714161445-14.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +131.2 KB
Content
image-20220714162600-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.8 KB
Content
image-20220714162617-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +1.3 MB
Content
image-20220714162629-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.5 KB
Content
image-20220714162652-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.5 KB
Content
image-20220714162713-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +104.0 KB
Content
image-20220714162725-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +13.7 KB
Content
image-20220714162737-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +135.2 KB
Content
image-20220714162752-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +135.2 KB
Content
image-20220714162805-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +165.9 KB
Content
image-20220714162814-10.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +50.2 KB
Content
image-20220714162827-11.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +94.3 KB
Content
image-20220714162841-12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +62.5 KB
Content
image-20220714162856-13.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +131.6 KB
Content
image-20220820164423-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +18.4 KB
Content
image-20220822172124-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +38.7 KB
Content
image-20220822172228-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +48.8 KB
Content
image-20220822172553-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +19.9 KB
Content
image-20220822172623-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +111.2 KB
Content
image-20220822172657-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +141.6 KB
Content
image-20220822172730-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +130.7 KB
Content
image-20220824104124-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +14.6 KB
Content
image-20220824104909-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +278.8 KB
Content