Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54

From 139.1 to 140.1 From 171.1 to 172.1

From version 140.1

edited by Ben
on 2022/08/29 14:01

Change comment: There is no comment for this version

To version 171.1

edited by Bob
on 2022/11/16 10:56

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 31 added, 0 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Ben
++XWiki.Bob

Content

@@ -182,7 +182,7 @@
  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
--**1）PLC Settings**
++**1）V-BOX setting**
  |**Item**|**Settings**|**Note**
  |Protocol|Allen-Bradlley DF1 Advanced|
@@ -436,7 +436,7 @@
  Supported Series: Siemens S7-300 series PLC
--**1）PLC Setting**
++**1）V-BOX setting**
  |**Items**|**Settings**|**Note**
  |Protocol|Simens S7-300 Ethernet|
@@ -498,7 +498,7 @@
  Supported Series: Siemens S7-400, S7-1200 and S7-1500
--**1）PLC Setting**
++**1）V-BOX setting**
  |=**Items**|=**Settings**|=**Note**
  |Protocol|Siemens S7-XXX|
@@ -704,6 +704,112 @@
  [[image:image-20220825100845-4.png]]
++== **FX3U Ethernet Protocol** ==
++
++ Mitsubishi FX3U series PLC
++
++**HMI Settings**
++
++|Items|Settings|Note
++|Protocol|Mitsubishi FX3U|
++|Connection|Ethernet|
++|Port No.|5009|Must be the same as the PLC setting
++|PLC station No.|0|
++
++**Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
++|Y|Y|Y OOO|0~~377|
++|M|M|M DDDD|0~~7679|
++|SM|SM|SM DDDD|8000~~8511|
++|S|S|S DDDD|0~~4095|
++|TS|TS|TS DDD|0~~511|
++|CS|CS|CS DDD|0~~255|
++|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
++|TN|TN|TN DDD|0~~511|
++|D|D|D DDDD|0~~7999|
++|SD|SD|SD DDDD|8000~~8511|
++|R|R|R DDDDD|0~~32767|
++
++**Ethernet Module Settings**
++
++FX3U-ENET-L module configuration
++Set up the FX3U-ENET-L Ethernet module settings as follows.
++Select the module location, which in this document is Module 0.
++
++[[image:image-20221116094003-1.png]]
++
++
++Select "Operational setting" to enter the following screen.
++
++The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
++
++[[image:image-20221116094019-2.png]]
++
++
++Select "Open setting" to enter the setting interface, the settings are as follows.
++
++The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
++
++Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
++
++[[image:image-20221116094038-3.png]]
++
++
++Click on "transter setup" - "PC side I/F setting", see the following figure.
++
++After setting, the first download must use the programming cable, as shown in the figure; after that, can
++
++use the IP set in the "Ethernet board" to communicate directly with the network cable.
++
++[[image:image-20221116094122-4.png||height="422" width="707"]]
++
++
++Read and write data from the Ethernet module
++
++[[image:image-20221116094131-5.png||height="551" width="708"]]
++
++
++Set "Transter setup" to COM communication, and read or write operation as shown below
++
++[[image:image-20221116094150-6.png]]
++
++
++**PLC Settings (GX Works 2)**
++
++Create a blank FX5U project
++
++Find Current Connection in the navigation
++
++[[image:image-20221116094206-7.png||height="425" width="711"]]
++
++
++Select Connection Channel List
++
++Select Ethernet board communication
++
++[[image:image-20221116094709-9.png||height="427" width="715"]]
++
++
++Select Ethernet Module
++Set the IP address of the PLC
++
++[[image:image-20221116094736-11.png||height="682" width="716"]]
++
++
++Read or write PLC data, in this document is read
++
++[[image:image-20221116094755-12.png||height="426" width="715"]]
++
++[[image:image-20221116094803-13.png||height="427" width="715"]]
++
++**V-BOX Communication Setting**
++
++
++
++
++
  == **FX5U Serial Protocol** ==
  Mitsubishi FX5U series PLC
@@ -858,11 +858,10 @@
  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
--**5）电缆布线**
++**5）Cable Wiring**
  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
--
  == **L02 Serial Protocol** ==
  Mitsubishi L02 series CPU built-in serial port.
@@ -1076,6 +1076,52 @@
  [[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
++== **AS Ethernet Protocol** ==
++
++**1）V-BOX Settings**
++
++|=**Items**|=**Settings**|=**Note**
++|Protocol|DELTA AS300 MODBUS TCP|
++|Connection|Ethernet|
++|Port No.|502|
++|Device No.|1|
++|HMI No.|0|
++
++**2）Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|Bit|X|X|X d|0~~63|
++|Bit|Y|Y|Y d|0~~63|
++|Bit|D|D|D d|0~~29999|
++|Bit|M|M|M d|0~~8191|
++|Bit|SM|SM|SM d|0~~4095|
++|Bit|S|S|S h|0~~2047|
++|Bit|T|T|T d|0~~511|
++|Bit|C|C|C d|0~~511|
++|Bit|HC|HC|HC d|0~~255|
++|Word|X|X|X h|0~~63|
++|Word|Y|Y|Y d|0~~63|
++|Word|SR|SR|SR d|0~~2047|
++|Word|D|D|D d|0~~29999|
++|Word|T|T|T d|0~~511|
++|Word|C|C|C h|0~~511|
++|Word|E|E|E d|0~~9|
++
++**3）Configure the communication protocol**
++
++
++[[image:image-20220831160010-4.png]]
++
++**4）Cable Wiring**
++
++Figure
++
++[[image:image-20220831155101-1.png]][[image:image-20220831160055-5.png]]
++
++Pin Definition Diagram
++
++[[image:image-20220831155157-3.png]]
++
  = Create communication with **Omron PLC** =
  == **CP1 Series Protocol ** ==
@@ -1086,10 +1086,424 @@
  [[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CJ2M.zip]]
--= Create communication with **Modbus RTU** =
--== **V-BOX as Slave** ==
++== **EC55 Series Protocol** ==
++Supported device: EC55 temperature instrument
++
++**1）V-BOX Settings**
++
++|**Items**|**Settings**|**Note**
++|Protocol|Omron EC55|
++|Connection|RS485 (9600, 2, 7, EVEN)|
++|Port No.|None|
++|PLC station No.|0|
++
++**2）Address List**
++
++|**Type**|**Register**|**Device range**|**HMI range**|**Function**
++|(% rowspan="3" %)Double word|C0|0-13 (Hex)|0-19|Set read only parameter for area 0
++|C1|0-4D(Hex)|0-77|Set Read/Write parameter for area 0
++|C3|0-CD(Hex)|0-205|Set Read/Write parameter for area 1
++|(% rowspan="6" %)Word|80|0-13(Hex)|0-19|Set read only parameter in area 0
++|81|0-4D(Hex)|0-77|Set Read/Write parameter in area 0
++|83|0-CD(Hex)|0-205|Set Read/Write parameter in area 1
++|CP|-|0-6|Read controller intrinsic property
++|CS|-|0-2|Read controller states
++|CA|-|0-17|Action command
++
++**3）Device Settings**
++
++Omron E5CC PLC configuration
++
++After entering the Communication Settings menu, please set the parameters to the default values for the following table. Press the cycle key of the instrument to enter the next setting.
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_3d95e093792ba98a.png?width=550&height=229&rev=1.1||alt="12.PLC Protocol_html_3d95e093792ba98a.png" height="229" width="550"]]
++
++According to PLC configuration and communication port configuration information of the HMI, provide the corresponding steps and configuration screenshots. This configuration needs to communicate properly with the above PLC configuration. The project settings are as follows
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_be583aa69dd6cf4c.png?width=550&height=242&rev=1.1||alt="12.PLC Protocol_html_be583aa69dd6cf4c.png" height="242" width="550"]]
++
++**✎Note:** The communication settings for HMI should be consistent with this setting.
++
++**4）Configure the communication protocol**
++
++[[image:image-20220831161041-1.png]]
++
++**5）Cable Wiring**
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
++
++**✎Note:**
++
++* COM3 only available in PI8000/PI9000 series.
++* CA address could not support continuous writing function；
++* Because of CP address intrinsic property: read control intrinsic property, so please place the character input part in use. Set address with CP0 and character length 10, used to display controller type. And place a number input part, set address with CP5 (cache size). Do not place other CP type address without CP0 in screen, otherwise CP type address is invalid
++* When set value into read & write address, it is necessary to switch the temperature instrument meter to the corresponding interface according to the menu of the instrument where the address locates, so that the value could be written, otherwise, the value could not be written; When the communication write setting of the instrument is turned off, the writing function is invalid. Writing function could be opened by using the 00 address of the CA register, which write 01 value.
++* When continuous writing of a value to a read-write address, please make sure all continuous writing address could be written. Otherwise, if one of these addresses could not be written, then all continuous writing commands will fail.
++* Because of the mechanism problem, this protocol could not support CompoWay/F function that is read-write function of variables in protocol document.
++* When using double-word address, set the data format to 32 bits, otherwise the read/write function is unable.
++* Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
++* [[image:image-20220831161356-1.png]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
++
++= Create communication with Xinje** PLC** =
++
++== **XC serial protocol** ==
++
++**1）V-BOX Settings**
++
++|**Item**|**Settings**|**Note**
++|Protocol|XINJE XC MODBUS|
++|Connection|RS232|
++|Baud rate|19200|
++|Data bit|8|
++|Parity|EVEN|
++|Stop bit|1|
++|PLC station No.|1|
++
++**2）Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|Bit|M|M|M d|0~~8511|
++|Bit|X|X|X o|0~~1747|
++|Bit|Y|Y|Y o|0~~1747|
++|Bit|S|S|S d|0~~1023|
++|Bit|T|T|T d|0~~4095|
++|Bit|C|C|C d|0~~634|
++|Word|D|D|D d|0~~8511|
++|Word|TD|TD|TD d|0~~618|
++|Word|CD|CD|CD d|0~~634|
++|Word|FD|FD|FD d|0~~8511|
++
++**3）Configure the communication protocol**
++
++
++[[image:image-20220831163041-1.png]]
++
++**4）Cable Wiring**
++
++Figure
++
++[[image:image-20220831163406-2.png]][[image:image-20220831163422-3.png]]
++
++Pin Definition Diagram
++
++[[image:image-20220831163441-4.png]]
++
++== **XD serial protocol** ==
++
++**1）V-BOX Settings**
++
++Supported Series: Delta Xinjie XD/XE Series PLC
++
++|**Item**|**Settings**|**Note**
++|Protocol|XINJE XD/XC MODBUS|
++|Connection|RS232|
++|Baud rate|19200|
++|Data bit|8|
++|Parity|EVEN|
++|Stop bit|1|
++|PLC station No.|1|
++
++**2）Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|Bit|M|M|M d|0~~74999|
++|Bit|X1xx|X1xx|X1xx o|0~~1177|
++|Bit|X2xx|X2xx|X2xx o|0~~277|
++|Bit|X|X|X o|0~~77|
++|Bit|Y1xx|Y1xx|Y1xx o|0~~1177|
++|Bit|Y2xx|Y2xx|Y2xx o|0~~277|
++|Bit|Y|Y|Y o|0~~4095|
++|Bit|SM|SM|SM d|0~~4999|(((
++
++)))
++|Bit|T|T|T d|0~~4999|
++|Bit|C|C|C d|0~~4999|
++|Bit|ET|ET|ET d|0~~31|
++|Bit|SE|SE|SE d|0~~31|
++|Bit|HM|HM|HM d|0~~11999|
++|Bit|HSC|HSC|HSC d|0~~39|
++|Bit|HS|HS|HS d|0~~999|
++|Bit|HT|HT|HT d|0~~1999|
++|Bit|HC|HC|HC d|0~~1999|
++|Bit|S|S|S d|0~~7999|
++|Word|D|D|D d|0~~69999|
++|Word|ID|ID|ID d|0~~99|
++|Word|ID1xx|ID1xx|ID1xx d|0~~999|
++|Word|ID2xx|ID2xx|ID2xx d|0~~299|
++|Word|QD|QD|QD d|0~~99|
++|Word|QD1xx|QD1xx|QD1xx d|0~~999|
++|Word|QD2xx|QD2xx|QD2xx d|0~~299|
++|Word|SD|SD|SD d|0~~4999|
++|Word|TD|TD|TD d|0~~575|
++|Word|CD|CD|CD d|0~~575|
++|Word|ETD|ETD|ETD d|0~~31|
++|Word|HD|HD|HD d|0~~24999|
++|Word|HSD|HSD|HSD d|0~~1023|
++|Word|HTD|HTD|HTD d|0~~95|
++|Word|HCD|HCD|HCD d|0~~95|
++|Word|HSCD|HSCD|HSCD d|0~~31|
++|Word|FD|FD|FD d|0~~8191|
++|Word|SFD|SFD|SFD d|0~~5999|
++|Word|FS|FS|FS d|0~~47|
++
++**3）Configure the communication protocol**
++
++[[image:image-20220831163923-7.png]]
++
++
++
++**4）Cable Wiring**
++
++Figure
++
++[[image:image-20220831163406-2.png]][[image:image-20220831163553-6.png]]
++
++Pin Definition Diagram
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
++
++
++= Create communication with **Schneider PLC** =
++
++== **Schneider MODBUS RTU** ==
++
++**1）V-BOX Setting**
++
++|=**Parameters**|=**Recommended**|=**Notes**
++|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
++|**Connection**|RS485|
++|**Baud rate**|19200|
++|**Data bit**|8|
++|**Parity**|Even|
++|**Stop bit**|1|
++|**PLC station No.**|1|
++
++**2）Address List**
++
++|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
++|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
++|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
++|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
++|W|MW|DDDDDD|0 ~~ 999999|Output register
++|DW|MD|DDDDDD|0 ~~ 999999|Output register
++
++**3）Configure the communication protocol**
++
++[[image:image-20220902104329-1.png]]
++
++**4）Cable Wiring**
++
++**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
++
++= Create communication with Inovance** PLC** =
++
++== **H3U serial protocol** ==
++
++**1）V-BOX Settings**
++
++|**Item**|**Settings**|**Note**
++|Protocol|INOVANCE H3U PLC|
++|Connection|RS422|
++|Baud rate|9600|
++|Data bit|7|
++|Parity|EVEN|
++|Stop bit|1|
++|PLC station No.|0|
++
++**2）Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|Bit|X|X|X o|0~~303237|
++|Bit|Y|Y|Y o|0~~303237|
++|Bit|M|M|M d|0~~99999|
++|Bit|T|T|T d|0~~99999|
++|Bit|C|C|C d|0~~99999|
++|Bit|SM|SM|SM d|8000~~999|
++|Bit|S|T|S d|0~~99999|
++|Bit|Lamp|Lamp|Lamp d|0~~0|
++|Word|X|X|X o|0~~303237|
++|Word|Y|Y|Y o|0~~303237|
++|Word|M|M|M d|0~~99999|
++|Word|T|T|T d|0~~99999|
++|Word|C|C|C d|0~~199|
++|Word|D|D|D d|0~~7999|
++|Word|S|S|S d|0~~99999|
++|Word|SD|SD|SD d|8000~~9999|
++|Word|R|R|R d|0~~32767|
++
++**3）Configure the communication protocol**
++
++[[image:image-20220831164626-1.png]]
++
++
++
++**4）Cable Wiring**
++
++Figure
++
++[[image:image-20220831164646-2.png]][[image:image-20220831164700-3.png]]
++
++Pin Definition Diagram
++
++[[image:image-20220831164731-4.png]]
++
++= Create communication with Panasonic** PLC** =
++
++== **FP serial protocol** ==
++
++**1）V-BOX Settings**
++
++|**Item**|**Settings**|**Note**
++|Protocol|Panasonic FP MFWTOCOL|
++|Connection|RS232|
++|Baud rate|9600|
++|Data bit|8|
++|Parity|ODD|
++|Stop bit|1|
++|PLC station No.|1|
++
++**2）Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|Bit|X|X|X d|0~~9999|
++|Bit|Y|Y|Y d|0~~9999|
++|Bit|R|R|R d|0~~9999|
++|Bit|T|T|T d|0~~9999|
++|Bit|C|C|C d|0~~9999|
++|Bit|L|L|L d|0~~9999|
++|Word|WX|WX|WX d|0~~9999|
++|Word|WY|WY|WY d|0~~9999|
++|Word|WR|WR|WR d|0~~9999|
++|Word|WL|WL|WL d|0~~9999|
++|Word|LD|LD|LD d|0~~9999|
++|Word|DT|DT|DT d|0~~65535|
++|Word|FL|FL|FL d|0~~9999|
++|Word|EV|EV|EV d|0~~9999|
++|Word|SV|SV|SV d|0~~9999|
++
++**3）Configure the communication protocol**
++
++[[image:image-20220831165238-4.png]]
++
++
++
++**4）Cable Wiring**
++
++Figure
++
++[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
++
++Pin Definition Diagram
++
++[[image:image-20220831165008-1.png]]
++
++= Create communication with LS** PLC** =
++
++== **XBC serial protocol** ==
++
++**1）V-BOX Settings**
++
++|**Item**|**Settings**|**Note**
++|Protocol|LS XBC CNet|
++|Connection|RS232|
++|Baud rate|115200|
++|Data bit|8|
++|Parity|NONE|
++|Stop bit|1|
++|PLC station No.|1|
++
++**2）Address List**
++
++|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
++|Bit|P|P|P d|0~~2047|
++|Bit|M|M|M d|0~~2047|
++|Bit|L|L|L d|0~~11263|
++|Bit|K|K|K d|0~~16183|
++|Bit|F|F|F d|0~~2047|
++|Bit|D|D|D d|0~~32767|
++|Bit|R|R|R d|0~~32767|
++|Bit|U|U|U d|0~~4095|
++|Word|P|P|P d|0~~2047|
++|Word|M|M|M d|0~~2047|
++|Word|L|L|L d|0~~11263|
++|Word|K|K|K d|0~~16183|
++|Word|F|F|F d|0~~2047|
++|Word|C|C|C d|0~~2047|
++|Word|T|T|T d|0~~2047|
++|Word|D|D|D d|0~~32767|
++|Word|N|N|N d|0~~21503|
++|Word|R|R|R d|0~~32767|
++|Word|U|U|U d|0~~4095|
++|Word|Z|Z|Z d|0~~127|
++|Word|S|S|S d|0~~127|
++
++**3）Configure the communication protocol**
++
++[[image:image-20220831170147-1.png]]
++
++**4）Cable Wiring**
++
++Figure
++
++[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
++
++Pin Definition Diagram
++
++[[image:image-20220831170215-2.png]]
++
++== **XGK FEnet Ethernet protocol** ==
++
++Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
++
++**1）V-BOX Settings**
++
++|**Items**|**Settings**|**Note**
++|Protocol|LG XGK FEnet(Ethernet)|
++|Connection|Ethernet|
++|Port No.|2004|
++
++**2）Address List**
++
++|**Type**|**Register**|**Range**|**Format**|**Note**
++|(% rowspan="14" %)Word|P|0~~2047|P d|
++|M|0~~2047|M d|
++|K|0~~2047|K d|
++|F|0~~2047|F d|
++|T|0~~2047|T d|
++|C|0~~2047|C d|
++|Z|0~~127|Z d|
++|S|0~~127|S d|
++|L|0~~11263|L d|
++|N|0~~21503|N d|
++|D|0~~32767|D d|
++|R|0~~32767|R d|
++|ZR|0~~65535|ZR d|
++|UxDD|0~~6331|UxDD nndd|nn: 0~~63, dd: 0~~31
++
++**✎Note:**
++
++* In addition to the "UxDD" register, the others correspond to the PLC register one by one. UxDD corresponds to U in the PLC;
++* The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
++* All bit registers are in the form of bits in word, and the range is the same as the word register;
++
++**3）Communication Settings**
++
++[[image:image-20220831171127-1.png]]
++
++**4）Cable Wiring**
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
++
++= Create communication with **Modbus ** =
++
++== **MODBUS RTU Slave (All function)** ==
++
  Select the protocol "Modbus RTU Slave (All Fuction)",
  Then set baud rate, port, stop bits, data bits, parity.
@@ -1097,7 +1097,7 @@
  (% style="text-align:center" %)
  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
--== **V-BOX as Master** ==
++== **MODBUS RTU Master** ==
  Select the protocol "Modbus RTU Master",
@@ -1133,6 +1133,61 @@
  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
  |0F (Write multiple bits)
++== **MODBUS TCP Slave (All function)** ==
++
++Supported series: MODBUS TCP controller
++
++V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
++
++**1）V-BOX Setting**
++
++|**Items**|**Settings**|**Note**
++|Protocol|MODBUS TCP Slave (All function)|
++|Connection|Ethernet|
++|Port No.|502|
++|PLC station No.|1
++
++**2）Address List**
++
++|**Type**|**Register**|**Function code & Description**
++|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
++|06 (write single register: write a binary value to a holding register)
++|10 (write values to multiple addresses )
++|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
++|06 (write single register: write a binary value to a holding register)
++|10 (write values to multiple addresses )
++|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
++|06 (write single register: write a binary value to a holding register)
++|10 (write values to multiple addresses )
++|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
++|10 (write values to multiple addresses )
++|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
++|05 (Force a single coil to force the on/off state of a logic coil)
++|0F (Write multiple bits, ie write continuously)
++|(% rowspan="3" %)1|02 (Read the input state)
++|05 (Force a single coil to force the on/off state of a logic coil)
++|0F (Write multiple bits)
++|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
++|05 (Force a single coil to force the on/off state of a logic coil)
++|0F (Write multiple bits)
++|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
++|0F (Write multiple bits)
++
++**3）Communication Settings**
++
++Configure V-BOX Ethernet IP in Networking Settings
++
++[[image:image-20220902111833-3.png]]
++
++
++Configure PLC Ethernet IP in Communication；
++
++[[image:image-20220902111121-1.png]]
++
++**4）Cable Wiring**
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
++
  == **communicate with VB inverter** ==
  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]

image-20220831155101-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+34.6 KB

Content

image-20220831155129-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+44.9 KB

Content

image-20220831155157-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+20.8 KB

Content

image-20220831160010-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+59.6 KB

Content

image-20220831160055-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+51.5 KB

Content

image-20220831161041-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+58.1 KB

Content

image-20220831161356-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+27.0 KB

Content

image-20220831163041-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+58.6 KB

Content

image-20220831163406-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+28.4 KB

Content

image-20220831163422-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+53.9 KB

Content

image-20220831163441-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.7 KB

Content

image-20220831163548-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+37.1 KB

Content

image-20220831163553-6.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+37.1 KB

Content

image-20220831163923-7.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+57.3 KB

Content

image-20220831164626-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+56.1 KB

Content

image-20220831164646-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+28.4 KB

Content

image-20220831164700-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+66.6 KB

Content

image-20220831164731-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+12.3 KB

Content

image-20220831165008-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.3 KB

Content

image-20220831165017-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+36.2 KB

Content

image-20220831165031-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+28.3 KB

Content

image-20220831165238-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+57.4 KB

Content

image-20220831170147-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+57.1 KB

Content

image-20220831170215-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+14.3 KB

Content

image-20220831170254-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+43.5 KB

Content

image-20220831170306-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+28.5 KB

Content

image-20220831171127-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+60.1 KB

Content

image-20220902104329-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+58.7 KB

Content

image-20220902111121-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+60.9 KB

Content

image-20220902111754-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+57.6 KB

Content

image-20220902111833-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Ben

Size

...	...	@@ -1,0 +1,1 @@
	1	+56.1 KB

Content

Changes for page 1 Communication

Summary

Details

Navigation

Table of Contents