Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 146.1
edited by Ben
on 2022/08/31 16:24
Change comment: There is no comment for this version
To version 165.1
edited by Bob
on 2022/11/15 19:58
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Ben
1 +XWiki.Bob
Content
... ... @@ -182,7 +182,7 @@
182 182  
183 183  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
184 184  
185 -**1）PLC Settings**
185 +**1）V-BOX setting**
186 186  
187 187  |**Item**|**Settings**|**Note**
188 188  |Protocol|Allen-Bradlley DF1 Advanced|
... ... @@ -436,7 +436,7 @@
436 436  
437 437  Supported Series: Siemens S7-300 series PLC
438 438  
439 -**1）PLC Setting**
439 +**1）V-BOX setting**
440 440  
441 441  |**Items**|**Settings**|**Note**
442 442  |Protocol|Simens S7-300 Ethernet|
... ... @@ -498,7 +498,7 @@
498 498  
499 499  Supported Series: Siemens S7-400, S7-1200 and S7-1500
500 500  
501 -**1）PLC Setting**
501 +**1）V-BOX setting**
502 502  
503 503  |=**Items**|=**Settings**|=**Note**
504 504  |Protocol|Siemens S7-XXX|
... ... @@ -704,6 +704,98 @@
704 704  [[image:image-20220825100845-4.png]]
705 705  
706 706  
707 +== ** FX3U Ethernet Protocol** ==
708 +
709 +Mitsubishi FX3U series PLC
710 +
711 +**HMI Settings**
712 +
713 +|Items|Settings|Note
714 +|Protocol|Mitsubishi FX3U|
715 +|Connection|Ethernet|
716 +|Port No.|5009|Must be the same as the PLC setting
717 +|PLC station No.|0|
718 +
719 +**Address List**
720 +
721 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
722 +|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
723 +|Y|Y|Y OOO|0~~377|
724 +|M|M|M DDDD|0~~7679|
725 +|SM|SM|SM DDDD|8000~~8511|
726 +|S|S|S DDDD|0~~4095|
727 +|TS|TS|TS DDD|0~~511|
728 +|CS|CS|CS DDD|0~~255|
729 +|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
730 +|TN|TN|TN DDD|0~~511|
731 +|D|D|D DDDD|0~~7999|
732 +|SD|SD|SD DDDD|8000~~8511|
733 +|R|R|R DDDDD|0~~32767|
734 +
735 +**Ethernet Module Settings**
736 +
737 +FX3U-ENET-L module configuration
738 +Set up the FX3U-ENET-L Ethernet module settings as follows.
739 +Select the module location, which in this document is Module 0.
740 +
741 +[[image:image-20221115140802-1.png]]
742 +
743 +Select "Operational setting" to enter the following screen.
744 +
745 +The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
746 +
747 +[[image:image-20221115142728-4.png]]
748 +
749 +Select "Open setting" to enter the setting interface, the settings are as follows.
750 +
751 +The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
752 +
753 +Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
754 +
755 +[[image:image-20221115142945-5.png]]
756 +
757 +Click on "transter setup" - "PC side I/F setting", see the following figure.
758 +
759 +After setting, the first download must use the programming cable, as shown in the figure; after that, can
760 +
761 +use the IP set in the "Ethernet board" to communicate directly with the network cable.
762 +
763 +[[image:image-20221115143341-6.png||height="426" width="712"]]
764 +
765 +Read and write data from the Ethernet module
766 +
767 +[[image:image-20221115143703-7.png]]
768 +
769 +Set "Transter setup" to COM communication, and read or write operation as shown below
770 +
771 +[[image:image-20221115143809-8.png]]
772 +
773 +**PLC Settings (GX Works 2)**
774 +
775 +Create a blank FX5U project
776 +
777 +Find Current Connection in the navigation
778 +
779 +[[image:image-20221115144335-9.png||height="422" width="706"]]
780 +
781 +Select Connection Channel List
782 +
783 +Select Ethernet board communication
784 +
785 +[[image:image-20221115144824-10.png||height="421" width="705"]]
786 +
787 +Select Ethernet Module
788 +Set the IP address of the PLC
789 +
790 +[[image:image-20221115145228-11.png||height="674" width="708"]]
791 +
792 +Read or write PLC data, in this document is read
793 +
794 +[[image:image-20221115145553-12.png||height="424" width="711"]]
795 +
796 +[[image:image-20221115145559-13.png||height="424" width="711"]]
797 +
798 +
707 707  == **FX5U Serial Protocol** ==
708 708  
709 709  Mitsubishi FX5U series PLC
... ... @@ -1194,10 +1194,362 @@
1194 1194  * Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
1195 1195  * [[image:image-20220831161356-1.png]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
1196 1196  
1197 -= Create communication with **Modbus RTU** =
1289 += Create communication with Xinje** PLC** =
1198 1198  
1199 -== **V-BOX as Slave** ==
1291 +== **XC serial protocol** ==
1200 1200  
1293 +**1）V-BOX Settings**
1294 +
1295 +|**Item**|**Settings**|**Note**
1296 +|Protocol|XINJE XC MODBUS|
1297 +|Connection|RS232|
1298 +|Baud rate|19200|
1299 +|Data bit|8|
1300 +|Parity|EVEN|
1301 +|Stop bit|1|
1302 +|PLC station No.|1|
1303 +
1304 +**2）Address List**
1305 +
1306 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1307 +|Bit|M|M|M d|0~~8511|
1308 +|Bit|X|X|X o|0~~1747|
1309 +|Bit|Y|Y|Y o|0~~1747|
1310 +|Bit|S|S|S d|0~~1023|
1311 +|Bit|T|T|T d|0~~4095|
1312 +|Bit|C|C|C d|0~~634|
1313 +|Word|D|D|D d|0~~8511|
1314 +|Word|TD|TD|TD d|0~~618|
1315 +|Word|CD|CD|CD d|0~~634|
1316 +|Word|FD|FD|FD d|0~~8511|
1317 +
1318 +**3）Configure the communication protocol**
1319 +
1320 +
1321 +[[image:image-20220831163041-1.png]]
1322 +
1323 +**4）Cable Wiring**
1324 +
1325 +Figure
1326 +
1327 +[[image:image-20220831163406-2.png]][[image:image-20220831163422-3.png]]
1328 +
1329 +Pin Definition Diagram
1330 +
1331 +[[image:image-20220831163441-4.png]]
1332 +
1333 +== **XD serial protocol** ==
1334 +
1335 +**1）V-BOX Settings**
1336 +
1337 +Supported Series: Delta Xinjie XD/XE Series PLC
1338 +
1339 +|**Item**|**Settings**|**Note**
1340 +|Protocol|XINJE XD/XC MODBUS|
1341 +|Connection|RS232|
1342 +|Baud rate|19200|
1343 +|Data bit|8|
1344 +|Parity|EVEN|
1345 +|Stop bit|1|
1346 +|PLC station No.|1|
1347 +
1348 +**2）Address List**
1349 +
1350 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1351 +|Bit|M|M|M d|0~~74999|
1352 +|Bit|X1xx|X1xx|X1xx o|0~~1177|
1353 +|Bit|X2xx|X2xx|X2xx o|0~~277|
1354 +|Bit|X|X|X o|0~~77|
1355 +|Bit|Y1xx|Y1xx|Y1xx o|0~~1177|
1356 +|Bit|Y2xx|Y2xx|Y2xx o|0~~277|
1357 +|Bit|Y|Y|Y o|0~~4095|
1358 +|Bit|SM|SM|SM d|0~~4999|(((
1359 +
1360 +)))
1361 +|Bit|T|T|T d|0~~4999|
1362 +|Bit|C|C|C d|0~~4999|
1363 +|Bit|ET|ET|ET d|0~~31|
1364 +|Bit|SE|SE|SE d|0~~31|
1365 +|Bit|HM|HM|HM d|0~~11999|
1366 +|Bit|HSC|HSC|HSC d|0~~39|
1367 +|Bit|HS|HS|HS d|0~~999|
1368 +|Bit|HT|HT|HT d|0~~1999|
1369 +|Bit|HC|HC|HC d|0~~1999|
1370 +|Bit|S|S|S d|0~~7999|
1371 +|Word|D|D|D d|0~~69999|
1372 +|Word|ID|ID|ID d|0~~99|
1373 +|Word|ID1xx|ID1xx|ID1xx d|0~~999|
1374 +|Word|ID2xx|ID2xx|ID2xx d|0~~299|
1375 +|Word|QD|QD|QD d|0~~99|
1376 +|Word|QD1xx|QD1xx|QD1xx d|0~~999|
1377 +|Word|QD2xx|QD2xx|QD2xx d|0~~299|
1378 +|Word|SD|SD|SD d|0~~4999|
1379 +|Word|TD|TD|TD d|0~~575|
1380 +|Word|CD|CD|CD d|0~~575|
1381 +|Word|ETD|ETD|ETD d|0~~31|
1382 +|Word|HD|HD|HD d|0~~24999|
1383 +|Word|HSD|HSD|HSD d|0~~1023|
1384 +|Word|HTD|HTD|HTD d|0~~95|
1385 +|Word|HCD|HCD|HCD d|0~~95|
1386 +|Word|HSCD|HSCD|HSCD d|0~~31|
1387 +|Word|FD|FD|FD d|0~~8191|
1388 +|Word|SFD|SFD|SFD d|0~~5999|
1389 +|Word|FS|FS|FS d|0~~47|
1390 +
1391 +**3）Configure the communication protocol**
1392 +
1393 +[[image:image-20220831163923-7.png]]
1394 +
1395 +
1396 +
1397 +**4）Cable Wiring**
1398 +
1399 +Figure
1400 +
1401 +[[image:image-20220831163406-2.png]][[image:image-20220831163553-6.png]]
1402 +
1403 +Pin Definition Diagram
1404 +
1405 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
1406 +
1407 +
1408 += Create communication with **Schneider PLC** =
1409 +
1410 +== **Schneider MODBUS RTU** ==
1411 +
1412 +**1）V-BOX Setting**
1413 +
1414 +|=**Parameters**|=**Recommended**|=**Notes**
1415 +|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
1416 +|**Connection**|RS485|
1417 +|**Baud rate**|19200|
1418 +|**Data bit**|8|
1419 +|**Parity**|Even|
1420 +|**Stop bit**|1|
1421 +|**PLC station No.**|1|
1422 +
1423 +**2）Address List**
1424 +
1425 +|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
1426 +|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
1427 +|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
1428 +|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
1429 +|W|MW|DDDDDD|0 ~~ 999999|Output register
1430 +|DW|MD|DDDDDD|0 ~~ 999999|Output register
1431 +
1432 +**3）Configure the communication protocol**
1433 +
1434 +[[image:image-20220902104329-1.png]]
1435 +
1436 +**4）Cable Wiring**
1437 +
1438 +**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
1439 +
1440 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
1441 +
1442 += Create communication with Inovance** PLC** =
1443 +
1444 +== **H3U serial protocol** ==
1445 +
1446 +**1）V-BOX Settings**
1447 +
1448 +|**Item**|**Settings**|**Note**
1449 +|Protocol|INOVANCE H3U PLC|
1450 +|Connection|RS422|
1451 +|Baud rate|9600|
1452 +|Data bit|7|
1453 +|Parity|EVEN|
1454 +|Stop bit|1|
1455 +|PLC station No.|0|
1456 +
1457 +**2）Address List**
1458 +
1459 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1460 +|Bit|X|X|X o|0~~303237|
1461 +|Bit|Y|Y|Y o|0~~303237|
1462 +|Bit|M|M|M d|0~~99999|
1463 +|Bit|T|T|T d|0~~99999|
1464 +|Bit|C|C|C d|0~~99999|
1465 +|Bit|SM|SM|SM d|8000~~999|
1466 +|Bit|S|T|S d|0~~99999|
1467 +|Bit|Lamp|Lamp|Lamp d|0~~0|
1468 +|Word|X|X|X o|0~~303237|
1469 +|Word|Y|Y|Y o|0~~303237|
1470 +|Word|M|M|M d|0~~99999|
1471 +|Word|T|T|T d|0~~99999|
1472 +|Word|C|C|C d|0~~199|
1473 +|Word|D|D|D d|0~~7999|
1474 +|Word|S|S|S d|0~~99999|
1475 +|Word|SD|SD|SD d|8000~~9999|
1476 +|Word|R|R|R d|0~~32767|
1477 +
1478 +**3）Configure the communication protocol**
1479 +
1480 +[[image:image-20220831164626-1.png]]
1481 +
1482 +
1483 +
1484 +**4）Cable Wiring**
1485 +
1486 +Figure
1487 +
1488 +[[image:image-20220831164646-2.png]][[image:image-20220831164700-3.png]]
1489 +
1490 +Pin Definition Diagram
1491 +
1492 +[[image:image-20220831164731-4.png]]
1493 +
1494 += Create communication with Panasonic** PLC** =
1495 +
1496 +== **FP serial protocol** ==
1497 +
1498 +**1）V-BOX Settings**
1499 +
1500 +|**Item**|**Settings**|**Note**
1501 +|Protocol|Panasonic FP MFWTOCOL|
1502 +|Connection|RS232|
1503 +|Baud rate|9600|
1504 +|Data bit|8|
1505 +|Parity|ODD|
1506 +|Stop bit|1|
1507 +|PLC station No.|1|
1508 +
1509 +**2）Address List**
1510 +
1511 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1512 +|Bit|X|X|X d|0~~9999|
1513 +|Bit|Y|Y|Y d|0~~9999|
1514 +|Bit|R|R|R d|0~~9999|
1515 +|Bit|T|T|T d|0~~9999|
1516 +|Bit|C|C|C d|0~~9999|
1517 +|Bit|L|L|L d|0~~9999|
1518 +|Word|WX|WX|WX d|0~~9999|
1519 +|Word|WY|WY|WY d|0~~9999|
1520 +|Word|WR|WR|WR d|0~~9999|
1521 +|Word|WL|WL|WL d|0~~9999|
1522 +|Word|LD|LD|LD d|0~~9999|
1523 +|Word|DT|DT|DT d|0~~65535|
1524 +|Word|FL|FL|FL d|0~~9999|
1525 +|Word|EV|EV|EV d|0~~9999|
1526 +|Word|SV|SV|SV d|0~~9999|
1527 +
1528 +**3）Configure the communication protocol**
1529 +
1530 +[[image:image-20220831165238-4.png]]
1531 +
1532 +
1533 +
1534 +**4）Cable Wiring**
1535 +
1536 +Figure
1537 +
1538 +[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
1539 +
1540 +Pin Definition Diagram
1541 +
1542 +[[image:image-20220831165008-1.png]]
1543 +
1544 += Create communication with LS** PLC** =
1545 +
1546 +== **XBC serial protocol** ==
1547 +
1548 +**1）V-BOX Settings**
1549 +
1550 +|**Item**|**Settings**|**Note**
1551 +|Protocol|LS XBC CNet|
1552 +|Connection|RS232|
1553 +|Baud rate|115200|
1554 +|Data bit|8|
1555 +|Parity|NONE|
1556 +|Stop bit|1|
1557 +|PLC station No.|1|
1558 +
1559 +**2）Address List**
1560 +
1561 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1562 +|Bit|P|P|P d|0~~2047|
1563 +|Bit|M|M|M d|0~~2047|
1564 +|Bit|L|L|L d|0~~11263|
1565 +|Bit|K|K|K d|0~~16183|
1566 +|Bit|F|F|F d|0~~2047|
1567 +|Bit|D|D|D d|0~~32767|
1568 +|Bit|R|R|R d|0~~32767|
1569 +|Bit|U|U|U d|0~~4095|
1570 +|Word|P|P|P d|0~~2047|
1571 +|Word|M|M|M d|0~~2047|
1572 +|Word|L|L|L d|0~~11263|
1573 +|Word|K|K|K d|0~~16183|
1574 +|Word|F|F|F d|0~~2047|
1575 +|Word|C|C|C d|0~~2047|
1576 +|Word|T|T|T d|0~~2047|
1577 +|Word|D|D|D d|0~~32767|
1578 +|Word|N|N|N d|0~~21503|
1579 +|Word|R|R|R d|0~~32767|
1580 +|Word|U|U|U d|0~~4095|
1581 +|Word|Z|Z|Z d|0~~127|
1582 +|Word|S|S|S d|0~~127|
1583 +
1584 +**3）Configure the communication protocol**
1585 +
1586 +[[image:image-20220831170147-1.png]]
1587 +
1588 +**4）Cable Wiring**
1589 +
1590 +Figure
1591 +
1592 +[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
1593 +
1594 +Pin Definition Diagram
1595 +
1596 +[[image:image-20220831170215-2.png]]
1597 +
1598 +== **XGK FEnet Ethernet protocol** ==
1599 +
1600 +Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
1601 +
1602 +**1）V-BOX Settings**
1603 +
1604 +|**Items**|**Settings**|**Note**
1605 +|Protocol|LG XGK FEnet(Ethernet)|
1606 +|Connection|Ethernet|
1607 +|Port No.|2004|
1608 +
1609 +**2）Address List**
1610 +
1611 +|**Type**|**Register**|**Range**|**Format**|**Note**
1612 +|(% rowspan="14" %)Word|P|0~~2047|P d|
1613 +|M|0~~2047|M d|
1614 +|K|0~~2047|K d|
1615 +|F|0~~2047|F d|
1616 +|T|0~~2047|T d|
1617 +|C|0~~2047|C d|
1618 +|Z|0~~127|Z d|
1619 +|S|0~~127|S d|
1620 +|L|0~~11263|L d|
1621 +|N|0~~21503|N d|
1622 +|D|0~~32767|D d|
1623 +|R|0~~32767|R d|
1624 +|ZR|0~~65535|ZR d|
1625 +|UxDD|0~~6331|UxDD nndd|nn: 0~~63, dd: 0~~31
1626 +
1627 +**✎Note:**
1628 +
1629 +* In addition to the "UxDD" register, the others correspond to the PLC register one by one. UxDD corresponds to U in the PLC;
1630 +* The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
1631 +* All bit registers are in the form of bits in word, and the range is the same as the word register;
1632 +
1633 +**3）Communication Settings**
1634 +
1635 +[[image:image-20220831171127-1.png]]
1636 +
1637 +**4）Cable Wiring**
1638 +
1639 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1640 +
1641 += Create communication with **Modbus ** =
1642 +
1643 +== **MODBUS RTU Slave (All function)** ==
1644 +
1201 1201  Select the protocol "Modbus RTU Slave (All Fuction)",
1202 1202  
1203 1203  Then set baud rate, port, stop bits, data bits, parity.
... ... @@ -1205,7 +1205,7 @@
1205 1205  (% style="text-align:center" %)
1206 1206  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
1207 1207  
1208 -== **V-BOX as Master** ==
1652 +== **MODBUS RTU Master** ==
1209 1209  
1210 1210  Select the protocol "Modbus RTU Master",
1211 1211  
... ... @@ -1241,6 +1241,61 @@
1241 1241  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
1242 1242  |0F (Write multiple bits)
1243 1243  
1688 +== **MODBUS TCP Slave (All function)** ==
1689 +
1690 +Supported series: MODBUS TCP controller
1691 +
1692 +V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
1693 +
1694 +**1）V-BOX Setting**
1695 +
1696 +|**Items**|**Settings**|**Note**
1697 +|Protocol|MODBUS TCP Slave (All function)|
1698 +|Connection|Ethernet|
1699 +|Port No.|502|
1700 +|PLC station No.|1
1701 +
1702 +**2）Address List**
1703 +
1704 +|**Type**|**Register**|**Function code & Description**
1705 +|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
1706 +|06 (write single register: write a binary value to a holding register)
1707 +|10 (write values to multiple addresses )
1708 +|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
1709 +|06 (write single register: write a binary value to a holding register)
1710 +|10 (write values to multiple addresses )
1711 +|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
1712 +|06 (write single register: write a binary value to a holding register)
1713 +|10 (write values to multiple addresses )
1714 +|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
1715 +|10 (write values to multiple addresses )
1716 +|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
1717 +|05 (Force a single coil to force the on/off state of a logic coil)
1718 +|0F (Write multiple bits, ie write continuously)
1719 +|(% rowspan="3" %)1|02 (Read the input state)
1720 +|05 (Force a single coil to force the on/off state of a logic coil)
1721 +|0F (Write multiple bits)
1722 +|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
1723 +|05 (Force a single coil to force the on/off state of a logic coil)
1724 +|0F (Write multiple bits)
1725 +|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
1726 +|0F (Write multiple bits)
1727 +
1728 +**3）Communication Settings**
1729 +
1730 +Configure V-BOX Ethernet IP in Networking Settings
1731 +
1732 +[[image:image-20220902111833-3.png]]
1733 +
1734 +
1735 +Configure PLC Ethernet IP in Communication；
1736 +
1737 +[[image:image-20220902111121-1.png]]
1738 +
1739 +**4）Cable Wiring**
1740 +
1741 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1742 +
1244 1244  == **communicate with VB inverter** ==
1245 1245  
1246 1246  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]
image-20220831163041-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.6 KB
Content
image-20220831163406-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +28.4 KB
Content
image-20220831163422-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +53.9 KB
Content
image-20220831163441-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +13.7 KB
Content
image-20220831163548-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +37.1 KB
Content
image-20220831163553-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +37.1 KB
Content
image-20220831163923-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +57.3 KB
Content
image-20220831164626-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +56.1 KB
Content
image-20220831164646-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +28.4 KB
Content
image-20220831164700-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +66.6 KB
Content
image-20220831164731-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +12.3 KB
Content
image-20220831165008-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +13.3 KB
Content
image-20220831165017-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +36.2 KB
Content
image-20220831165031-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +28.3 KB
Content
image-20220831165238-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +57.4 KB
Content
image-20220831170147-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +57.1 KB
Content
image-20220831170215-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +14.3 KB
Content
image-20220831170254-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +43.5 KB
Content
image-20220831170306-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +28.5 KB
Content
image-20220831171127-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +60.1 KB
Content
image-20220902104329-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +58.7 KB
Content
image-20220902111121-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +60.9 KB
Content
image-20220902111754-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +57.6 KB
Content
image-20220902111833-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +56.1 KB
Content