Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 156.1
edited by Ben
on 2022/08/31 17:20
Change comment: There is no comment for this version
To version 150.1
edited by Ben
on 2022/08/31 16:48
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -182,7 +182,7 @@
182 182  
183 183  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
184 184  
185 -**1）V-BOX setting**
185 +**1）PLC Settings**
186 186  
187 187  |**Item**|**Settings**|**Note**
188 188  |Protocol|Allen-Bradlley DF1 Advanced|
... ... @@ -1364,11 +1364,11 @@
1364 1364  
1365 1365  [[image:image-20220831164731-4.png]]
1366 1366  
1367 -= Create communication with Panasonic** PLC** =
1367 += Create communication with Panasonic** PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=39]] =
1368 1368  
1369 -== **FP serial protocol** ==
1369 +== **FP serial protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=40]] ==
1370 1370  
1371 -**1）V-BOX Settings**
1371 +**1）HMI Settings**
1372 1372  
1373 1373  |**Item**|**Settings**|**Note**
1374 1374  |Protocol|Panasonic FP MFWTOCOL|
... ... @@ -1400,25 +1400,25 @@
1400 1400  
1401 1401  **3）Configure the communication protocol**
1402 1402  
1403 -[[image:image-20220831165238-4.png]]
1403 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171050-1.png?rev=1.1||alt="image-20220830171050-1.png"]]
1404 1404  
1405 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171126-2.png?rev=1.1||alt="image-20220830171126-2.png"]]
1405 1405  
1406 -
1407 1407  **4）Cable Wiring**
1408 1408  
1409 1409  Figure
1410 1410  
1411 -[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
1411 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171328-4.png?rev=1.1||alt="image-20220830171328-4.png"]]
1412 1412  
1413 1413  Pin Definition Diagram
1414 1414  
1415 -[[image:image-20220831165008-1.png]]
1415 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171146-3.png?rev=1.1||alt="image-20220830171146-3.png"]]
1416 1416  
1417 -= Create communication with LS** PLC** =
1417 += Create communication with LS** PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=41]] =
1418 1418  
1419 -== **XBC serial protocol** ==
1419 +== **XBC serial protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=42]] ==
1420 1420  
1421 -**1）V-BOX Settings**
1421 +**1）HMI Settings**
1422 1422  
1423 1423  |**Item**|**Settings**|**Note**
1424 1424  |Protocol|LS XBC CNet|
... ... @@ -1456,23 +1456,25 @@
1456 1456  
1457 1457  **3）Configure the communication protocol**
1458 1458  
1459 -[[image:image-20220831170147-1.png]]
1459 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174853-3.png?rev=1.1||alt="image-20220830174853-3.png"]]
1460 1460  
1461 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174733-2.png?rev=1.1||alt="image-20220830174733-2.png"]]
1462 +
1461 1461  **4）Cable Wiring**
1462 1462  
1463 1463  Figure
1464 1464  
1465 -[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
1467 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174659-1.png?rev=1.1||alt="image-20220830174659-1.png"]]
1466 1466  
1467 1467  Pin Definition Diagram
1468 1468  
1469 -[[image:image-20220831170215-2.png]]
1471 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830173402-8.png?rev=1.1||alt="image-20220830173402-8.png"]]
1470 1470  
1471 -== **XGK FEnet Ethernet protocol** ==
1473 +== **XGK FEnet Ethernet protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=43]] ==
1472 1472  
1473 1473  Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
1474 1474  
1475 -**1）V-BOX Settings**
1477 +**HMI Settings**
1476 1476  
1477 1477  |**Items**|**Settings**|**Note**
1478 1478  |Protocol|LG XGK FEnet(Ethernet)|
... ... @@ -1479,7 +1479,7 @@
1479 1479  |Connection|Ethernet|
1480 1480  |Port No.|2004|
1481 1481  
1482 -**2）Address List**
1484 +**Address List**
1483 1483  
1484 1484  |**Type**|**Register**|**Range**|**Format**|**Note**
1485 1485  |(% rowspan="14" %)Word|P|0~~2047|P d|
... ... @@ -1503,14 +1503,182 @@
1503 1503  * The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
1504 1504  * All bit registers are in the form of bits in word, and the range is the same as the word register;
1505 1505  
1506 -**3）Communication Settings**
1508 +**Communication settings in HMI**
1507 1507  
1508 -[[image:image-20220831171127-1.png]]
1510 +Enable HMI Ethernet in [Project Settings];
1509 1509  
1510 -**4）Cable Wiring**
1512 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_43b671f18153910d.png?width=405&height=107&rev=1.1||alt="12.PLC Protocol_html_43b671f18153910d.png" height="107" width="405"]]
1511 1511  
1514 +Set PLC IP in [Device IP] settings;
1515 +
1516 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_a2a19b5003ad4090.png?width=554&height=189&rev=1.1||alt="12.PLC Protocol_html_a2a19b5003ad4090.png" height="189" width="554"]]
1517 +
1518 +**Cable Wiring**
1519 +
1512 1512  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1513 1513  
1522 += Create communication with **SHIMADEN PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=44]] =
1523 +
1524 +== **FP23 series protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=45]] ==
1525 +
1526 +Supported series: SHIMADEN FP23 series
1527 +
1528 +**HMI Setting**
1529 +
1530 +|**Items**|**Settings**|**Note**
1531 +|Protocol|SHIMADEN FP23 series|
1532 +|Connection|RS485 (9600, 1, 7, EVEN)|
1533 +|Port No.|None|
1534 +|PLC station No.|0|
1535 +
1536 +**Address List**
1537 +
1538 +|**Device address**|**HMI register**|**Address range**|**Type**
1539 +|0040-0043(HEX)|FP040|100064-200067|Read only
1540 +|0100-010B(HEX)|FP100|100256-200267|Read only
1541 +|0110-0142(HEX)|FP110|100272-200322|Read only
1542 +|0182-0252(HEX)|FP182|100386-200594|Write only
1543 +|0280-0281(HEX)|FP280|100640-200641|Read only
1544 +|0300-030B(HEX)|FP300|100768-200779|Read and write
1545 +|0380-039F(HEX)|FP380|100896-200927|Read and write
1546 +|0400-04D7(HEX)|FP400|101024-201239|Read and write
1547 +|0500-05B0(HEX)|FP500|101280-201456|Read and write
1548 +|0600-0670(HEX)|FP600|101536-201814|Read and write
1549 +|0720-0738(HEX)|FP720|101824-201848|Read and write
1550 +|0800-083F(HEX)|FP800|102048-202111|Read and write
1551 +|0900-0952(HEX)|FP900|102304-202386|Read and write
1552 +|　|Ctrl|0-2|
1553 +
1554 +**✎Note:**
1555 +
1556 +* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
1557 +* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in FP23;
1558 +* The Ctrl register is used to store the control group number and BCC check mode.
1559 +
1560 +**Ctrl Register Description**
1561 +
1562 +* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
1563 +* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
1564 +* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
1565 +* Ctrl3 reserved
1566 +
1567 +**✎Note:**
1568 +
1569 +After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
1570 +
1571 +**Cable Wiring**
1572 +
1573 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1574 +
1575 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1576 +
1577 +**✎Note:** COM3 only available in PI8000/PI9000 series.
1578 +
1579 +== **SR90 protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=46]] ==
1580 +
1581 +Supported series: SHIMADEN SR90 series
1582 +
1583 +**HMI Setting**
1584 +
1585 +|**Items**|**Settings**|**Note**
1586 +|Protocol|SHIMADEN SR90 protocol|
1587 +|Connection|RS485 (1200, 1, 7, EVEN)|
1588 +|Port No.|None|
1589 +|PLC station No.|0|
1590 +
1591 +**Address List**
1592 +
1593 +|**Device address**|**HMI register**|**Address range**|**Type**
1594 +|0040-0043 (HEX)|SR040|100064-100067|Read only
1595 +|0100-010A(HEX)|SR0100|100256-100266|Read only
1596 +|0182-018C(HEX)|SR0182|100386-100396|Write only
1597 +|0300-04FE(HEX)|SR0300|100768-101278|Write/read
1598 +|0500-050B(HEX)|SR0500|101280-101291|Write/read
1599 +|0590-0611(HEX)|SR0590|101424-101553|Write/read
1600 +|0701-0709(HEX)|SR0701|101793-101801|Write/read
1601 +| |Ctrl|0-2|~-~-
1602 +
1603 +**✎Note:**
1604 +
1605 +* The upper 2 bits of the address of HMIs are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
1606 +* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in SR90;
1607 +* The Ctrl register is used to store the control group number and BCC check mode. See how to use it below;
1608 +
1609 +**Ctrl Register Description**
1610 +
1611 +* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
1612 +* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
1613 +* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
1614 +* Ctrl3 reserved
1615 +
1616 +**✎Note:**
1617 +
1618 +After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
1619 +
1620 +**Cable Wiring**
1621 +
1622 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1623 +
1624 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1625 +
1626 +**✎Note:** COM3 only available in PI8000/PI9000 series.
1627 +
1628 +== **MR13 series(standard protocol)**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=47]] ==
1629 +
1630 +Supported series: SHIMADEN MR13 series
1631 +
1632 +**HMI Setting**
1633 +
1634 +|**Items**|**Settings**|**Note**
1635 +|Protocol|SHIMADEN standard protocol|
1636 +|Connection|RS485 (1200, 1, 7, EVEN)|
1637 +|Port No.|None|
1638 +|PLC station No.|0|
1639 +
1640 +**Address List**
1641 +
1642 +|**Device address**|**HMI register**|**Address range**|**Type**
1643 +|0100-010B(HEX)|MR100|100256-300267|Read only
1644 +|0111-0126(HEX)|MR111|100273-300294|Read only
1645 +|0184-0192(HEX)|MR184|100388-300402|Write only
1646 +|0280-0282(HEX)|MR280|100640-300642|Read only
1647 +|0300-030B(HEX)|MR300|100768-300779|Read/write
1648 +|0314-0317(HEX)|MR314|100788-300791|Read/write
1649 +|031A(HEX)|MR31A|100794-300794|Read/write
1650 +|0320-0321(HEX)|MR320|100800-300801|Read/write
1651 +|0400-0504(HEX)|MR400|101024-301284|Read/write
1652 +|0506(HEX)|MR506|101286-301286|Read/write
1653 +|0510-0514(HEX)|MR510|101296-301300|Read/write
1654 +|0516-0524(HEX)|MR516|101302-301316|Read/write
1655 +|0526(HEX)|MR526|101318-301318|Read/write
1656 +|0580-08C3(HEX)|MR580|101408-302243|Read/write
1657 +|~-~-|Ctrl|0-2|~-~-
1658 +
1659 +**✎Note:**
1660 +
1661 +* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
1662 +* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in MR13;
1663 +* The Ctrl register is used to store the control group number and BCC check mode.
1664 +
1665 +**Ctrl Register Description**
1666 +
1667 +* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
1668 +* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR, STX_ETX_CR LF and @_:_CR .
1669 +* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
1670 +* Ctrl3 reserved
1671 +
1672 +**✎Note:**
1673 +
1674 +After reloading project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
1675 +
1676 +**Cable Wiring**
1677 +
1678 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1679 +
1680 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1681 +
1682 +**✎Note:** COM3 only available in PI8000/PI9000 series.
1683 +
1514 1514  = Create communication with **Modbus RTU** =
1515 1515  
1516 1516  == **V-BOX as Slave** ==
image-20220831165008-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
image-20220831165017-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -36.2 KB
Content
image-20220831165031-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.3 KB
Content
image-20220831165238-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.4 KB
Content
image-20220831170147-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.1 KB
Content
image-20220831170215-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -14.3 KB
Content
image-20220831170254-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -43.5 KB
Content
image-20220831170306-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.5 KB
Content
image-20220831171127-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.1 KB
Content