Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 159.1
edited by Ben
on 2022/09/02 10:16
Change comment: There is no comment for this version
To version 150.1
edited by Ben
on 2022/08/31 16:48
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -182,7 +182,7 @@
182 182  
183 183  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
184 184  
185 -**1）V-BOX setting**
185 +**1）PLC Settings**
186 186  
187 187  |**Item**|**Settings**|**Note**
188 188  |Protocol|Allen-Bradlley DF1 Advanced|
... ... @@ -436,7 +436,7 @@
436 436  
437 437  Supported Series: Siemens S7-300 series PLC
438 438  
439 -**1）V-BOX setting**
439 +**1）PLC Setting**
440 440  
441 441  |**Items**|**Settings**|**Note**
442 442  |Protocol|Simens S7-300 Ethernet|
... ... @@ -498,7 +498,7 @@
498 498  
499 499  Supported Series: Siemens S7-400, S7-1200 and S7-1500
500 500  
501 -**1）V-BOX setting**
501 +**1）PLC Setting**
502 502  
503 503  |=**Items**|=**Settings**|=**Note**
504 504  |Protocol|Siemens S7-XXX|
... ... @@ -1312,44 +1312,6 @@
1312 1312  
1313 1313  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
1314 1314  
1315 -
1316 -= Create communication with **Schneider PLC** =
1317 -
1318 -== **Schneider MODBUS RTU** ==
1319 -
1320 -**1）V-BOX Setting**
1321 -
1322 -|=**Parameters**|=**Recommended**|=**Notes**
1323 -|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
1324 -|Connection|RS485|
1325 -|**Baud rate**|19200|
1326 -|**Data bit**|8|
1327 -|**Parity**|Even|
1328 -|**Stop bit**|1|
1329 -|**PLC station No.**|1|
1330 -
1331 -**PLC Setting**
1332 -
1333 -|=**Communication mode**|Modbus RTU protocol
1334 -
1335 -**2）Device Address**
1336 -
1337 -|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
1338 -|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
1339 -|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
1340 -|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
1341 -|W|MW|DDDDDD|0 ~~ 999999|Output register
1342 -|DW|MD|DDDDDD|0 ~~ 999999|Output register
1343 -
1344 -**3）Configure the communication protocol**
1345 -
1346 -
1347 -**4）Cable Wiring**
1348 -
1349 -**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
1350 -
1351 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
1352 -
1353 1353  = Create communication with Inovance** PLC** =
1354 1354  
1355 1355  == **H3U serial protocol** ==
... ... @@ -1402,11 +1402,11 @@
1402 1402  
1403 1403  [[image:image-20220831164731-4.png]]
1404 1404  
1405 -= Create communication with Panasonic** PLC** =
1367 += Create communication with Panasonic** PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=39]] =
1406 1406  
1407 -== **FP serial protocol** ==
1369 +== **FP serial protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=40]] ==
1408 1408  
1409 -**1）V-BOX Settings**
1371 +**1）HMI Settings**
1410 1410  
1411 1411  |**Item**|**Settings**|**Note**
1412 1412  |Protocol|Panasonic FP MFWTOCOL|
... ... @@ -1438,25 +1438,25 @@
1438 1438  
1439 1439  **3）Configure the communication protocol**
1440 1440  
1441 -[[image:image-20220831165238-4.png]]
1403 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171050-1.png?rev=1.1||alt="image-20220830171050-1.png"]]
1442 1442  
1405 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171126-2.png?rev=1.1||alt="image-20220830171126-2.png"]]
1443 1443  
1444 -
1445 1445  **4）Cable Wiring**
1446 1446  
1447 1447  Figure
1448 1448  
1449 -[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
1411 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171328-4.png?rev=1.1||alt="image-20220830171328-4.png"]]
1450 1450  
1451 1451  Pin Definition Diagram
1452 1452  
1453 -[[image:image-20220831165008-1.png]]
1415 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171146-3.png?rev=1.1||alt="image-20220830171146-3.png"]]
1454 1454  
1455 -= Create communication with LS** PLC** =
1417 += Create communication with LS** PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=41]] =
1456 1456  
1457 -== **XBC serial protocol** ==
1419 +== **XBC serial protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=42]] ==
1458 1458  
1459 -**1）V-BOX Settings**
1421 +**1）HMI Settings**
1460 1460  
1461 1461  |**Item**|**Settings**|**Note**
1462 1462  |Protocol|LS XBC CNet|
... ... @@ -1494,23 +1494,25 @@
1494 1494  
1495 1495  **3）Configure the communication protocol**
1496 1496  
1497 -[[image:image-20220831170147-1.png]]
1459 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174853-3.png?rev=1.1||alt="image-20220830174853-3.png"]]
1498 1498  
1461 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174733-2.png?rev=1.1||alt="image-20220830174733-2.png"]]
1462 +
1499 1499  **4）Cable Wiring**
1500 1500  
1501 1501  Figure
1502 1502  
1503 -[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
1467 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174659-1.png?rev=1.1||alt="image-20220830174659-1.png"]]
1504 1504  
1505 1505  Pin Definition Diagram
1506 1506  
1507 -[[image:image-20220831170215-2.png]]
1471 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830173402-8.png?rev=1.1||alt="image-20220830173402-8.png"]]
1508 1508  
1509 -== **XGK FEnet Ethernet protocol** ==
1473 +== **XGK FEnet Ethernet protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=43]] ==
1510 1510  
1511 1511  Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
1512 1512  
1513 -**1）V-BOX Settings**
1477 +**HMI Settings**
1514 1514  
1515 1515  |**Items**|**Settings**|**Note**
1516 1516  |Protocol|LG XGK FEnet(Ethernet)|
... ... @@ -1517,7 +1517,7 @@
1517 1517  |Connection|Ethernet|
1518 1518  |Port No.|2004|
1519 1519  
1520 -**2）Address List**
1484 +**Address List**
1521 1521  
1522 1522  |**Type**|**Register**|**Range**|**Format**|**Note**
1523 1523  |(% rowspan="14" %)Word|P|0~~2047|P d|
... ... @@ -1541,14 +1541,182 @@
1541 1541  * The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
1542 1542  * All bit registers are in the form of bits in word, and the range is the same as the word register;
1543 1543  
1544 -**3）Communication Settings**
1508 +**Communication settings in HMI**
1545 1545  
1546 -[[image:image-20220831171127-1.png]]
1510 +Enable HMI Ethernet in [Project Settings];
1547 1547  
1548 -**4）Cable Wiring**
1512 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_43b671f18153910d.png?width=405&height=107&rev=1.1||alt="12.PLC Protocol_html_43b671f18153910d.png" height="107" width="405"]]
1549 1549  
1514 +Set PLC IP in [Device IP] settings;
1515 +
1516 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_a2a19b5003ad4090.png?width=554&height=189&rev=1.1||alt="12.PLC Protocol_html_a2a19b5003ad4090.png" height="189" width="554"]]
1517 +
1518 +**Cable Wiring**
1519 +
1550 1550  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1551 1551  
1522 += Create communication with **SHIMADEN PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=44]] =
1523 +
1524 +== **FP23 series protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=45]] ==
1525 +
1526 +Supported series: SHIMADEN FP23 series
1527 +
1528 +**HMI Setting**
1529 +
1530 +|**Items**|**Settings**|**Note**
1531 +|Protocol|SHIMADEN FP23 series|
1532 +|Connection|RS485 (9600, 1, 7, EVEN)|
1533 +|Port No.|None|
1534 +|PLC station No.|0|
1535 +
1536 +**Address List**
1537 +
1538 +|**Device address**|**HMI register**|**Address range**|**Type**
1539 +|0040-0043(HEX)|FP040|100064-200067|Read only
1540 +|0100-010B(HEX)|FP100|100256-200267|Read only
1541 +|0110-0142(HEX)|FP110|100272-200322|Read only
1542 +|0182-0252(HEX)|FP182|100386-200594|Write only
1543 +|0280-0281(HEX)|FP280|100640-200641|Read only
1544 +|0300-030B(HEX)|FP300|100768-200779|Read and write
1545 +|0380-039F(HEX)|FP380|100896-200927|Read and write
1546 +|0400-04D7(HEX)|FP400|101024-201239|Read and write
1547 +|0500-05B0(HEX)|FP500|101280-201456|Read and write
1548 +|0600-0670(HEX)|FP600|101536-201814|Read and write
1549 +|0720-0738(HEX)|FP720|101824-201848|Read and write
1550 +|0800-083F(HEX)|FP800|102048-202111|Read and write
1551 +|0900-0952(HEX)|FP900|102304-202386|Read and write
1552 +|　|Ctrl|0-2|
1553 +
1554 +**✎Note:**
1555 +
1556 +* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
1557 +* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in FP23;
1558 +* The Ctrl register is used to store the control group number and BCC check mode.
1559 +
1560 +**Ctrl Register Description**
1561 +
1562 +* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
1563 +* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
1564 +* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
1565 +* Ctrl3 reserved
1566 +
1567 +**✎Note:**
1568 +
1569 +After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
1570 +
1571 +**Cable Wiring**
1572 +
1573 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1574 +
1575 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1576 +
1577 +**✎Note:** COM3 only available in PI8000/PI9000 series.
1578 +
1579 +== **SR90 protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=46]] ==
1580 +
1581 +Supported series: SHIMADEN SR90 series
1582 +
1583 +**HMI Setting**
1584 +
1585 +|**Items**|**Settings**|**Note**
1586 +|Protocol|SHIMADEN SR90 protocol|
1587 +|Connection|RS485 (1200, 1, 7, EVEN)|
1588 +|Port No.|None|
1589 +|PLC station No.|0|
1590 +
1591 +**Address List**
1592 +
1593 +|**Device address**|**HMI register**|**Address range**|**Type**
1594 +|0040-0043 (HEX)|SR040|100064-100067|Read only
1595 +|0100-010A(HEX)|SR0100|100256-100266|Read only
1596 +|0182-018C(HEX)|SR0182|100386-100396|Write only
1597 +|0300-04FE(HEX)|SR0300|100768-101278|Write/read
1598 +|0500-050B(HEX)|SR0500|101280-101291|Write/read
1599 +|0590-0611(HEX)|SR0590|101424-101553|Write/read
1600 +|0701-0709(HEX)|SR0701|101793-101801|Write/read
1601 +| |Ctrl|0-2|~-~-
1602 +
1603 +**✎Note:**
1604 +
1605 +* The upper 2 bits of the address of HMIs are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
1606 +* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in SR90;
1607 +* The Ctrl register is used to store the control group number and BCC check mode. See how to use it below;
1608 +
1609 +**Ctrl Register Description**
1610 +
1611 +* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
1612 +* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
1613 +* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
1614 +* Ctrl3 reserved
1615 +
1616 +**✎Note:**
1617 +
1618 +After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
1619 +
1620 +**Cable Wiring**
1621 +
1622 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1623 +
1624 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1625 +
1626 +**✎Note:** COM3 only available in PI8000/PI9000 series.
1627 +
1628 +== **MR13 series(standard protocol)**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=47]] ==
1629 +
1630 +Supported series: SHIMADEN MR13 series
1631 +
1632 +**HMI Setting**
1633 +
1634 +|**Items**|**Settings**|**Note**
1635 +|Protocol|SHIMADEN standard protocol|
1636 +|Connection|RS485 (1200, 1, 7, EVEN)|
1637 +|Port No.|None|
1638 +|PLC station No.|0|
1639 +
1640 +**Address List**
1641 +
1642 +|**Device address**|**HMI register**|**Address range**|**Type**
1643 +|0100-010B(HEX)|MR100|100256-300267|Read only
1644 +|0111-0126(HEX)|MR111|100273-300294|Read only
1645 +|0184-0192(HEX)|MR184|100388-300402|Write only
1646 +|0280-0282(HEX)|MR280|100640-300642|Read only
1647 +|0300-030B(HEX)|MR300|100768-300779|Read/write
1648 +|0314-0317(HEX)|MR314|100788-300791|Read/write
1649 +|031A(HEX)|MR31A|100794-300794|Read/write
1650 +|0320-0321(HEX)|MR320|100800-300801|Read/write
1651 +|0400-0504(HEX)|MR400|101024-301284|Read/write
1652 +|0506(HEX)|MR506|101286-301286|Read/write
1653 +|0510-0514(HEX)|MR510|101296-301300|Read/write
1654 +|0516-0524(HEX)|MR516|101302-301316|Read/write
1655 +|0526(HEX)|MR526|101318-301318|Read/write
1656 +|0580-08C3(HEX)|MR580|101408-302243|Read/write
1657 +|~-~-|Ctrl|0-2|~-~-
1658 +
1659 +**✎Note:**
1660 +
1661 +* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
1662 +* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in MR13;
1663 +* The Ctrl register is used to store the control group number and BCC check mode.
1664 +
1665 +**Ctrl Register Description**
1666 +
1667 +* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
1668 +* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR, STX_ETX_CR LF and @_:_CR .
1669 +* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
1670 +* Ctrl3 reserved
1671 +
1672 +**✎Note:**
1673 +
1674 +After reloading project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
1675 +
1676 +**Cable Wiring**
1677 +
1678 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1679 +
1680 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1681 +
1682 +**✎Note:** COM3 only available in PI8000/PI9000 series.
1683 +
1552 1552  = Create communication with **Modbus RTU** =
1553 1553  
1554 1554  == **V-BOX as Slave** ==
image-20220831165008-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
image-20220831165017-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -36.2 KB
Content
image-20220831165031-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.3 KB
Content
image-20220831165238-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.4 KB
Content
image-20220831170147-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.1 KB
Content
image-20220831170215-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -14.3 KB
Content
image-20220831170254-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -43.5 KB
Content
image-20220831170306-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.5 KB
Content
image-20220831171127-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.1 KB
Content