Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54

From 150.1 to 149.1 From 166.1 to 165.1

From version 165.1

edited by Bob
on 2022/11/15 19:58

Change comment: There is no comment for this version

To version 150.1

edited by Ben
on 2022/08/31 16:48

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 13 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Bob
++XWiki.Ben

Content

@@ -182,7 +182,7 @@
  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
--**1）V-BOX setting**
++**1）PLC Settings**
  |**Item**|**Settings**|**Note**
  |Protocol|Allen-Bradlley DF1 Advanced|
@@ -436,7 +436,7 @@
  Supported Series: Siemens S7-300 series PLC
--**1）V-BOX setting**
++**1）PLC Setting**
  |**Items**|**Settings**|**Note**
  |Protocol|Simens S7-300 Ethernet|
@@ -498,7 +498,7 @@
  Supported Series: Siemens S7-400, S7-1200 and S7-1500
--**1）V-BOX setting**
++**1）PLC Setting**
  |=**Items**|=**Settings**|=**Note**
  |Protocol|Siemens S7-XXX|
@@ -704,98 +704,6 @@
  [[image:image-20220825100845-4.png]]
--== ** FX3U Ethernet Protocol** ==
--
--Mitsubishi FX3U series PLC
--
--**HMI Settings**
--
--|Items|Settings|Note
--|Protocol|Mitsubishi FX3U|
--|Connection|Ethernet|
--|Port No.|5009|Must be the same as the PLC setting
--|PLC station No.|0|
--
--**Address List**
--
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
--|Y|Y|Y OOO|0~~377|
--|M|M|M DDDD|0~~7679|
--|SM|SM|SM DDDD|8000~~8511|
--|S|S|S DDDD|0~~4095|
--|TS|TS|TS DDD|0~~511|
--|CS|CS|CS DDD|0~~255|
--|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
--|TN|TN|TN DDD|0~~511|
--|D|D|D DDDD|0~~7999|
--|SD|SD|SD DDDD|8000~~8511|
--|R|R|R DDDDD|0~~32767|
--
--**Ethernet Module Settings**
--
--FX3U-ENET-L module configuration
--Set up the FX3U-ENET-L Ethernet module settings as follows.
--Select the module location, which in this document is Module 0.
--
--[[image:image-20221115140802-1.png]]
--
--Select "Operational setting" to enter the following screen.
--
--The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
--
--[[image:image-20221115142728-4.png]]
--
--Select "Open setting" to enter the setting interface, the settings are as follows.
--
--The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
--
--Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
--
--[[image:image-20221115142945-5.png]]
--
--Click on "transter setup" - "PC side I/F setting", see the following figure.
--
--After setting, the first download must use the programming cable, as shown in the figure; after that, can
--
--use the IP set in the "Ethernet board" to communicate directly with the network cable.
--
--[[image:image-20221115143341-6.png||height="426" width="712"]]
--
--Read and write data from the Ethernet module
--
--[[image:image-20221115143703-7.png]]
--
--Set "Transter setup" to COM communication, and read or write operation as shown below
--
--[[image:image-20221115143809-8.png]]
--
--**PLC Settings (GX Works 2)**
--
--Create a blank FX5U project
--
--Find Current Connection in the navigation
--
--[[image:image-20221115144335-9.png||height="422" width="706"]]
--
--Select Connection Channel List
--
--Select Ethernet board communication
--
--[[image:image-20221115144824-10.png||height="421" width="705"]]
--
--Select Ethernet Module
--Set the IP address of the PLC
--
--[[image:image-20221115145228-11.png||height="674" width="708"]]
--
--Read or write PLC data, in this document is read
--
--[[image:image-20221115145553-12.png||height="424" width="711"]]
--
--[[image:image-20221115145559-13.png||height="424" width="711"]]
--
--
  == **FX5U Serial Protocol** ==
  Mitsubishi FX5U series PLC
@@ -1404,41 +1404,6 @@
  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
--
--= Create communication with **Schneider PLC** =
--
--== **Schneider MODBUS RTU** ==
--
--**1）V-BOX Setting**
--
--|=**Parameters**|=**Recommended**|=**Notes**
--|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
--|**Connection**|RS485|
--|**Baud rate**|19200|
--|**Data bit**|8|
--|**Parity**|Even|
--|**Stop bit**|1|
--|**PLC station No.**|1|
--
--**2）Address List**
--
--|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
--|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
--|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
--|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
--|W|MW|DDDDDD|0 ~~ 999999|Output register
--|DW|MD|DDDDDD|0 ~~ 999999|Output register
--
--**3）Configure the communication protocol**
--
--[[image:image-20220902104329-1.png]]
--
--**4）Cable Wiring**
--
--**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
--
--[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
--
  = Create communication with Inovance** PLC** =
  == **H3U serial protocol** ==
@@ -1491,11 +1491,11 @@
  [[image:image-20220831164731-4.png]]
--= Create communication with Panasonic** PLC** =
++= Create communication with Panasonic** PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=39]] =
--== **FP serial protocol** ==
++== **FP serial protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=40]] ==
--**1）V-BOX Settings**
++**1）HMI Settings**
  |**Item**|**Settings**|**Note**
  |Protocol|Panasonic FP MFWTOCOL|
@@ -1527,25 +1527,25 @@
  **3）Configure the communication protocol**
--[[image:image-20220831165238-4.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171050-1.png?rev=1.1||alt="image-20220830171050-1.png"]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171126-2.png?rev=1.1||alt="image-20220830171126-2.png"]]
--
  **4）Cable Wiring**
  Figure
--[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171328-4.png?rev=1.1||alt="image-20220830171328-4.png"]]
  Pin Definition Diagram
--[[image:image-20220831165008-1.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830171146-3.png?rev=1.1||alt="image-20220830171146-3.png"]]
--= Create communication with LS** PLC** =
++= Create communication with LS** PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=41]] =
--== **XBC serial protocol** ==
++== **XBC serial protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=42]] ==
--**1）V-BOX Settings**
++**1）HMI Settings**
  |**Item**|**Settings**|**Note**
  |Protocol|LS XBC CNet|
@@ -1583,23 +1583,25 @@
  **3）Configure the communication protocol**
--[[image:image-20220831170147-1.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174853-3.png?rev=1.1||alt="image-20220830174853-3.png"]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174733-2.png?rev=1.1||alt="image-20220830174733-2.png"]]
++
  **4）Cable Wiring**
  Figure
--[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830174659-1.png?rev=1.1||alt="image-20220830174659-1.png"]]
  Pin Definition Diagram
--[[image:image-20220831170215-2.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830173402-8.png?rev=1.1||alt="image-20220830173402-8.png"]]
--== **XGK FEnet Ethernet protocol** ==
++== **XGK FEnet Ethernet protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=43]] ==
  Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
--**1）V-BOX Settings**
++**HMI Settings**
  |**Items**|**Settings**|**Note**
  |Protocol|LG XGK FEnet(Ethernet)|
@@ -1606,7 +1606,7 @@
  |Connection|Ethernet|
  |Port No.|2004|
--**2）Address List**
++**Address List**
  |**Type**|**Register**|**Range**|**Format**|**Note**
  |(% rowspan="14" %)Word|P|0~~2047|P d|
@@ -1630,18 +1630,186 @@
  * The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
  * All bit registers are in the form of bits in word, and the range is the same as the word register;
--**3）Communication Settings**
++**Communication settings in HMI**
--[[image:image-20220831171127-1.png]]
++Enable HMI Ethernet in [Project Settings];
--**4）Cable Wiring**
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_43b671f18153910d.png?width=405&height=107&rev=1.1||alt="12.PLC Protocol_html_43b671f18153910d.png" height="107" width="405"]]
++Set PLC IP in [Device IP] settings;
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_a2a19b5003ad4090.png?width=554&height=189&rev=1.1||alt="12.PLC Protocol_html_a2a19b5003ad4090.png" height="189" width="554"]]
++
++**Cable Wiring**
++
  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
--= Create communication with **Modbus ** =
++= Create communication with **SHIMADEN PLC**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=44]] =
--== **MODBUS RTU Slave (All function)** ==
++== **FP23 series protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=45]] ==
++Supported series: SHIMADEN FP23 series
++
++**HMI Setting**
++
++|**Items**|**Settings**|**Note**
++|Protocol|SHIMADEN FP23 series|
++|Connection|RS485 (9600, 1, 7, EVEN)|
++|Port No.|None|
++|PLC station No.|0|
++
++**Address List**
++
++|**Device address**|**HMI register**|**Address range**|**Type**
++|0040-0043(HEX)|FP040|100064-200067|Read only
++|0100-010B(HEX)|FP100|100256-200267|Read only
++|0110-0142(HEX)|FP110|100272-200322|Read only
++|0182-0252(HEX)|FP182|100386-200594|Write only
++|0280-0281(HEX)|FP280|100640-200641|Read only
++|0300-030B(HEX)|FP300|100768-200779|Read and write
++|0380-039F(HEX)|FP380|100896-200927|Read and write
++|0400-04D7(HEX)|FP400|101024-201239|Read and write
++|0500-05B0(HEX)|FP500|101280-201456|Read and write
++|0600-0670(HEX)|FP600|101536-201814|Read and write
++|0720-0738(HEX)|FP720|101824-201848|Read and write
++|0800-083F(HEX)|FP800|102048-202111|Read and write
++|0900-0952(HEX)|FP900|102304-202386|Read and write
++|　|Ctrl|0-2|
++
++**✎Note:**
++
++* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
++* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in FP23;
++* The Ctrl register is used to store the control group number and BCC check mode.
++
++**Ctrl Register Description**
++
++* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
++* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
++* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
++* Ctrl3 reserved
++
++**✎Note:**
++
++After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
++
++**Cable Wiring**
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
++
++**✎Note:** COM3 only available in PI8000/PI9000 series.
++
++== **SR90 protocol**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=46]] ==
++
++Supported series: SHIMADEN SR90 series
++
++**HMI Setting**
++
++|**Items**|**Settings**|**Note**
++|Protocol|SHIMADEN SR90 protocol|
++|Connection|RS485 (1200, 1, 7, EVEN)|
++|Port No.|None|
++|PLC station No.|0|
++
++**Address List**
++
++|**Device address**|**HMI register**|**Address range**|**Type**
++|0040-0043 (HEX)|SR040|100064-100067|Read only
++|0100-010A(HEX)|SR0100|100256-100266|Read only
++|0182-018C(HEX)|SR0182|100386-100396|Write only
++|0300-04FE(HEX)|SR0300|100768-101278|Write/read
++|0500-050B(HEX)|SR0500|101280-101291|Write/read
++|0590-0611(HEX)|SR0590|101424-101553|Write/read
++|0701-0709(HEX)|SR0701|101793-101801|Write/read
++| |Ctrl|0-2|~-~-
++
++**✎Note:**
++
++* The upper 2 bits of the address of HMIs are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
++* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in SR90;
++* The Ctrl register is used to store the control group number and BCC check mode. See how to use it below;
++
++**Ctrl Register Description**
++
++* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
++* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR , STX_ETX_CR LF and @_:_CR .
++* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
++* Ctrl3 reserved
++
++**✎Note:**
++
++After reloading the HMI project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
++
++**Cable Wiring**
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
++
++**✎Note:** COM3 only available in PI8000/PI9000 series.
++
++== **MR13 series(standard protocol)**[[Edit>>url:https://docs.we-con.com.cn/bin/edit/PIStudio/12.PLC%20protocols/WebHome?section=47]] ==
++
++Supported series: SHIMADEN MR13 series
++
++**HMI Setting**
++
++|**Items**|**Settings**|**Note**
++|Protocol|SHIMADEN standard protocol|
++|Connection|RS485 (1200, 1, 7, EVEN)|
++|Port No.|None|
++|PLC station No.|0|
++
++**Address List**
++
++|**Device address**|**HMI register**|**Address range**|**Type**
++|0100-010B(HEX)|MR100|100256-300267|Read only
++|0111-0126(HEX)|MR111|100273-300294|Read only
++|0184-0192(HEX)|MR184|100388-300402|Write only
++|0280-0282(HEX)|MR280|100640-300642|Read only
++|0300-030B(HEX)|MR300|100768-300779|Read/write
++|0314-0317(HEX)|MR314|100788-300791|Read/write
++|031A(HEX)|MR31A|100794-300794|Read/write
++|0320-0321(HEX)|MR320|100800-300801|Read/write
++|0400-0504(HEX)|MR400|101024-301284|Read/write
++|0506(HEX)|MR506|101286-301286|Read/write
++|0510-0514(HEX)|MR510|101296-301300|Read/write
++|0516-0524(HEX)|MR516|101302-301316|Read/write
++|0526(HEX)|MR526|101318-301318|Read/write
++|0580-08C3(HEX)|MR580|101408-302243|Read/write
++|~-~-|Ctrl|0-2|~-~-
++
++**✎Note:**
++
++* The upper 2 bits of the address of the HMI register are taken as the sub address, and the real address is the last four bits (for example, if the address is 100256, then 10 is the sub address as 1, and 0256 is the real address);
++* The address range in the table is only divided by the start and end addresses, and some of the addresses in the range have no corresponding address in MR13;
++* The Ctrl register is used to store the control group number and BCC check mode.
++
++**Ctrl Register Description**
++
++* The Ctrl register is a special register that does not communicate with the temperature controller. User needs to assign value in the screen according to the settings as in the temperature controller.
++* Ctrl0 indicates the setting of the control character, the valid values are 1, 2, 3 respectively, and the corresponding control group is: STX_ETX_CR, STX_ETX_CR LF and @_:_CR .
++* Ctrl1 indicates the BCC block check mode. The valid value range is 1-4. The corresponding check mode is: 1.ADD, 2.ADD_two's cmp, 3.XOR, 4.None;
++* Ctrl3 reserved
++
++**✎Note:**
++
++After reloading project or restarting the HMI, HMI will reset the value of ctrl0 and ctrl1 as 1, so user need to set these two values to make it the same as it in the temperature controller, then communication will be normal.
++
++**Cable Wiring**
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
++
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
++
++**✎Note:** COM3 only available in PI8000/PI9000 series.
++
++= Create communication with **Modbus RTU** =
++
++== **V-BOX as Slave** ==
++
  Select the protocol "Modbus RTU Slave (All Fuction)",
  Then set baud rate, port, stop bits, data bits, parity.
@@ -1649,7 +1649,7 @@
  (% style="text-align:center" %)
  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
--== **MODBUS RTU Master** ==
++== **V-BOX as Master** ==
  Select the protocol "Modbus RTU Master",
@@ -1685,61 +1685,6 @@
  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
  |0F (Write multiple bits)
--== **MODBUS TCP Slave (All function)** ==
--
--Supported series: MODBUS TCP controller
--
--V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
--
--**1）V-BOX Setting**
--
--|**Items**|**Settings**|**Note**
--|Protocol|MODBUS TCP Slave (All function)|
--|Connection|Ethernet|
--|Port No.|502|
--|PLC station No.|1
--
--**2）Address List**
--
--|**Type**|**Register**|**Function code & Description**
--|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
--|06 (write single register: write a binary value to a holding register)
--|10 (write values to multiple addresses )
--|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
--|06 (write single register: write a binary value to a holding register)
--|10 (write values to multiple addresses )
--|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
--|06 (write single register: write a binary value to a holding register)
--|10 (write values to multiple addresses )
--|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
--|10 (write values to multiple addresses )
--|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
--|05 (Force a single coil to force the on/off state of a logic coil)
--|0F (Write multiple bits, ie write continuously)
--|(% rowspan="3" %)1|02 (Read the input state)
--|05 (Force a single coil to force the on/off state of a logic coil)
--|0F (Write multiple bits)
--|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
--|05 (Force a single coil to force the on/off state of a logic coil)
--|0F (Write multiple bits)
--|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
--|0F (Write multiple bits)
--
--**3）Communication Settings**
--
--Configure V-BOX Ethernet IP in Networking Settings
--
--[[image:image-20220902111833-3.png]]
--
--
--Configure PLC Ethernet IP in Communication；
--
--[[image:image-20220902111121-1.png]]
--
--**4）Cable Wiring**
--
--[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
--
  == **communicate with VB inverter** ==
  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]

image-20220831165008-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-13.3 KB

Content

image-20220831165017-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-36.2 KB

Content

image-20220831165031-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-28.3 KB

Content

image-20220831165238-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.4 KB

Content

image-20220831170147-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.1 KB

Content

image-20220831170215-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-14.3 KB

Content

image-20220831170254-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-43.5 KB

Content

image-20220831170306-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-28.5 KB

Content

image-20220831171127-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-60.1 KB

Content

image-20220902104329-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-58.7 KB

Content

image-20220902111121-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-60.9 KB

Content

image-20220902111754-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.6 KB

Content

image-20220902111833-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-56.1 KB

Content

Changes for page 1 Communication

Summary

Details

Navigation

Table of Contents