Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 166.1
edited by Bob
on 2022/11/16 09:32
Change comment: There is no comment for this version
To version 169.2
edited by Bob
on 2022/11/16 10:50
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -704,9 +704,9 @@
704 704  [[image:image-20220825100845-4.png]]
705 705  
706 706  
707 -== ** FX3U Ethernet Protocol** ==
707 +== **FX3U Ethernet Protocol** ==
708 708  
709 -Mitsubishi FX3U series PLC
709 + Mitsubishi FX3U series PLC
710 710  
711 711  **HMI Settings**
712 712  
... ... @@ -738,14 +738,16 @@
738 738  Set up the FX3U-ENET-L Ethernet module settings as follows.
739 739  Select the module location, which in this document is Module 0.
740 740  
741 -[[image:image-20221115140802-1.png]]
741 +[[image:image-20221116094003-1.png]]
742 742  
743 +
743 743  Select "Operational setting" to enter the following screen.
744 744  
745 745  The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
746 746  
747 -[[image:image-20221115142728-4.png]]
748 +[[image:image-20221116094019-2.png]]
748 748  
750 +
749 749  Select "Open setting" to enter the setting interface, the settings are as follows.
750 750  
751 751  The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
... ... @@ -752,8 +752,9 @@
752 752  
753 753  Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
754 754  
755 -[[image:image-20221115142945-5.png]]
757 +[[image:image-20221116094038-3.png]]
756 756  
759 +
757 757  Click on "transter setup" - "PC side I/F setting", see the following figure.
758 758  
759 759  After setting, the first download must use the programming cable, as shown in the figure; after that, can
... ... @@ -760,16 +760,19 @@
760 760  
761 761  use the IP set in the "Ethernet board" to communicate directly with the network cable.
762 762  
763 -[[image:image-20221115143341-6.png||height="426" width="712"]]
766 +[[image:image-20221116094122-4.png||height="422" width="707"]]
764 764  
768 +
765 765  Read and write data from the Ethernet module
766 766  
767 -[[image:image-20221115143703-7.png]]
771 +[[image:image-20221116094131-5.png||height="551" width="708"]]
768 768  
773 +
769 769  Set "Transter setup" to COM communication, and read or write operation as shown below
770 770  
771 -[[image:image-20221115143809-8.png]]
776 +[[image:image-20221116094150-6.png]]
772 772  
778 +
773 773  **PLC Settings (GX Works 2)**
774 774  
775 775  Create a blank FX5U project
... ... @@ -776,25 +776,31 @@
776 776  
777 777  Find Current Connection in the navigation
778 778  
779 -[[image:image-20221115144335-9.png||height="422" width="706"]]
785 +[[image:image-20221116094206-7.png||height="425" width="711"]]
780 780  
787 +
781 781  Select Connection Channel List
782 782  
783 783  Select Ethernet board communication
784 784  
785 -[[image:image-20221115144824-10.png||height="421" width="705"]]
792 +[[image:image-20221116094709-9.png||height="427" width="715"]]
786 786  
794 +
787 787  Select Ethernet Module
788 788  Set the IP address of the PLC
789 789  
790 -[[image:image-20221115145228-11.png||height="674" width="708"]]
798 +[[image:image-20221116094736-11.png||height="682" width="716"]]
791 791  
800 +
792 792  Read or write PLC data, in this document is read
793 793  
794 -[[image:image-20221115145553-12.png||height="424" width="711"]]
803 +[[image:image-20221116094755-12.png||height="426" width="715"]]
795 795  
796 -[[image:image-20221115145559-13.png||height="424" width="711"]]
805 +[[image:image-20221116094803-13.png||height="427" width="715"]]
797 797  
807 +
808 +
809 +
798 798  == **FX5U Serial Protocol** ==
799 799  
800 800  Mitsubishi FX5U series PLC