Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 169.2
edited by Bob
on 2022/11/16 10:50
Change comment: There is no comment for this version
To version 173.1
edited by Bob
on 2022/11/16 11:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -732,20 +732,19 @@
732 732  |SD|SD|SD DDDD|8000~~8511|
733 733  |R|R|R DDDDD|0~~32767|
734 734  
735 -**Ethernet Module Settings**
735 +**1)Ethernet Module Settings**
736 736  
737 737  FX3U-ENET-L module configuration
738 738  Set up the FX3U-ENET-L Ethernet module settings as follows.
739 739  Select the module location, which in this document is Module 0.
740 740  
741 -[[image:image-20221116094003-1.png]]
741 +[[image:image-20221116105850-1.png]]
742 742  
743 -
744 744  Select "Operational setting" to enter the following screen.
745 745  
746 746  The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
747 747  
748 -[[image:image-20221116094019-2.png]]
747 +[[image:image-20221116105947-1.png]]
749 749  
750 750  
751 751  Select "Open setting" to enter the setting interface, the settings are as follows.
... ... @@ -754,7 +754,6 @@
754 754  
755 755  Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
756 756  
757 -[[image:image-20221116094038-3.png]]
758 758  
759 759  
760 760  Click on "transter setup" - "PC side I/F setting", see the following figure.
... ... @@ -763,17 +763,14 @@
763 763  
764 764  use the IP set in the "Ethernet board" to communicate directly with the network cable.
765 765  
766 -[[image:image-20221116094122-4.png||height="422" width="707"]]
767 767  
768 768  
769 769  Read and write data from the Ethernet module
770 770  
771 -[[image:image-20221116094131-5.png||height="551" width="708"]]
772 772  
773 773  
774 774  Set "Transter setup" to COM communication, and read or write operation as shown below
775 775  
776 -[[image:image-20221116094150-6.png]]
777 777  
778 778  
779 779  **PLC Settings (GX Works 2)**
... ... @@ -782,7 +782,6 @@
782 782  
783 783  Find Current Connection in the navigation
784 784  
785 -[[image:image-20221116094206-7.png||height="425" width="711"]]
786 786  
787 787  
788 788  Select Connection Channel List
... ... @@ -789,22 +789,20 @@
789 789  
790 790  Select Ethernet board communication
791 791  
792 -[[image:image-20221116094709-9.png||height="427" width="715"]]
793 793  
794 794  
795 795  Select Ethernet Module
796 796  Set the IP address of the PLC
797 797  
798 -[[image:image-20221116094736-11.png||height="682" width="716"]]
799 799  
800 800  
801 801  Read or write PLC data, in this document is read
802 802  
803 -[[image:image-20221116094755-12.png||height="426" width="715"]]
804 804  
805 -[[image:image-20221116094803-13.png||height="427" width="715"]]
806 806  
797 +**V-BOX Communication Setting**
807 807  
799 +
808 808  
809 809  
810 810  == **FX5U Serial Protocol** ==
... ... @@ -961,11 +961,10 @@
961 961  
962 962  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
963 963  
964 -**5）电缆布线**
956 +**5）Cable Wiring**
965 965  
966 966  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
967 967  
968 -
969 969  == **L02 Serial Protocol** ==
970 970  
971 971  Mitsubishi L02 series CPU built-in serial port.
image-20221116105850-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bob
Size
... ... @@ -1,0 +1,1 @@
1 +18.9 KB
Content
image-20221116105947-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bob
Size
... ... @@ -1,0 +1,1 @@
1 +18.7 KB
Content