Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54

From version 171.1
edited by Bob
on 2022/11/16 10:56
Change comment: There is no comment for this version
To version 139.1
edited by Ben
on 2022/08/29 13:59
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Bob
1 +XWiki.Ben
Content
... ... @@ -182,7 +182,7 @@
182 182  
183 183  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
184 184  
185 -**1)V-BOX setting**
185 +**1)PLC Settings**
186 186  
187 187  |**Item**|**Settings**|**Note**
188 188  |Protocol|Allen-Bradlley DF1 Advanced|
... ... @@ -436,7 +436,7 @@
436 436  
437 437  Supported Series: Siemens S7-300 series PLC
438 438  
439 -**1)V-BOX setting**
439 +**1)PLC Setting**
440 440  
441 441  |**Items**|**Settings**|**Note**
442 442  |Protocol|Simens S7-300 Ethernet|
... ... @@ -498,7 +498,7 @@
498 498  
499 499  Supported Series: Siemens S7-400, S7-1200 and S7-1500
500 500  
501 -**1)V-BOX setting**
501 +**1)PLC Setting**
502 502  
503 503  |=**Items**|=**Settings**|=**Note**
504 504  |Protocol|Siemens S7-XXX|
... ... @@ -704,112 +704,6 @@
704 704  [[image:image-20220825100845-4.png]]
705 705  
706 706  
707 -== **FX3U Ethernet Protocol** ==
708 -
709 - Mitsubishi FX3U series PLC
710 -
711 -**HMI Settings**
712 -
713 -|Items|Settings|Note
714 -|Protocol|Mitsubishi FX3U|
715 -|Connection|Ethernet|
716 -|Port No.|5009|Must be the same as the PLC setting
717 -|PLC station No.|0|
718 -
719 -**Address List**
720 -
721 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
722 -|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
723 -|Y|Y|Y OOO|0~~377|
724 -|M|M|M DDDD|0~~7679|
725 -|SM|SM|SM DDDD|8000~~8511|
726 -|S|S|S DDDD|0~~4095|
727 -|TS|TS|TS DDD|0~~511|
728 -|CS|CS|CS DDD|0~~255|
729 -|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
730 -|TN|TN|TN DDD|0~~511|
731 -|D|D|D DDDD|0~~7999|
732 -|SD|SD|SD DDDD|8000~~8511|
733 -|R|R|R DDDDD|0~~32767|
734 -
735 -**Ethernet Module Settings**
736 -
737 -FX3U-ENET-L module configuration
738 -Set up the FX3U-ENET-L Ethernet module settings as follows.
739 -Select the module location, which in this document is Module 0.
740 -
741 -[[image:image-20221116094003-1.png]]
742 -
743 -
744 -Select "Operational setting" to enter the following screen.
745 -
746 -The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
747 -
748 -[[image:image-20221116094019-2.png]]
749 -
750 -
751 -Select "Open setting" to enter the setting interface, the settings are as follows.
752 -
753 -The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
754 -
755 -Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
756 -
757 -[[image:image-20221116094038-3.png]]
758 -
759 -
760 -Click on "transter setup" - "PC side I/F setting", see the following figure.
761 -
762 -After setting, the first download must use the programming cable, as shown in the figure; after that, can
763 -
764 -use the IP set in the "Ethernet board" to communicate directly with the network cable.
765 -
766 -[[image:image-20221116094122-4.png||height="422" width="707"]]
767 -
768 -
769 -Read and write data from the Ethernet module
770 -
771 -[[image:image-20221116094131-5.png||height="551" width="708"]]
772 -
773 -
774 -Set "Transter setup" to COM communication, and read or write operation as shown below
775 -
776 -[[image:image-20221116094150-6.png]]
777 -
778 -
779 -**PLC Settings (GX Works 2)**
780 -
781 -Create a blank FX5U project
782 -
783 -Find Current Connection in the navigation
784 -
785 -[[image:image-20221116094206-7.png||height="425" width="711"]]
786 -
787 -
788 -Select Connection Channel List
789 -
790 -Select Ethernet board communication
791 -
792 -[[image:image-20221116094709-9.png||height="427" width="715"]]
793 -
794 -
795 -Select Ethernet Module
796 -Set the IP address of the PLC
797 -
798 -[[image:image-20221116094736-11.png||height="682" width="716"]]
799 -
800 -
801 -Read or write PLC data, in this document is read
802 -
803 -[[image:image-20221116094755-12.png||height="426" width="715"]]
804 -
805 -[[image:image-20221116094803-13.png||height="427" width="715"]]
806 -
807 -**V-BOX Communication Setting**
808 -
809 -
810 -
811 -
812 -
813 813  == **FX5U Serial Protocol** ==
814 814  
815 815  Mitsubishi FX5U series PLC
... ... @@ -964,10 +964,11 @@
964 964  
965 965  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
966 966  
967 -**5)Cable Wiring**
861 +**5)电缆布线**
968 968  
969 969  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
970 970  
865 +
971 971  == **L02 Serial Protocol** ==
972 972  
973 973  Mitsubishi L02 series CPU built-in serial port.
... ... @@ -1181,480 +1181,20 @@
1181 1181  
1182 1182  [[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
1183 1183  
1184 -== **AS Ethernet Protocol** ==
1185 -
1186 -**1)V-BOX Settings**
1187 -
1188 -|=**Items**|=**Settings**|=**Note**
1189 -|Protocol|DELTA AS300 MODBUS TCP|
1190 -|Connection|Ethernet|
1191 -|Port No.|502|
1192 -|Device No.|1|
1193 -|HMI No.|0|
1194 -
1195 -**2)Address List**
1196 -
1197 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1198 -|Bit|X|X|X d|0~~63|
1199 -|Bit|Y|Y|Y d|0~~63|
1200 -|Bit|D|D|D d|0~~29999|
1201 -|Bit|M|M|M d|0~~8191|
1202 -|Bit|SM|SM|SM d|0~~4095|
1203 -|Bit|S|S|S h|0~~2047|
1204 -|Bit|T|T|T d|0~~511|
1205 -|Bit|C|C|C d|0~~511|
1206 -|Bit|HC|HC|HC d|0~~255|
1207 -|Word|X|X|X h|0~~63|
1208 -|Word|Y|Y|Y d|0~~63|
1209 -|Word|SR|SR|SR d|0~~2047|
1210 -|Word|D|D|D d|0~~29999|
1211 -|Word|T|T|T d|0~~511|
1212 -|Word|C|C|C h|0~~511|
1213 -|Word|E|E|E d|0~~9|
1214 -
1215 -**3)Configure the communication protocol**
1216 -
1217 -
1218 -[[image:image-20220831160010-4.png]]
1219 -
1220 -**4)Cable Wiring**
1221 -
1222 -Figure
1223 -
1224 -[[image:image-20220831155101-1.png]][[image:image-20220831160055-5.png]]
1225 -
1226 -Pin Definition Diagram
1227 -
1228 -[[image:image-20220831155157-3.png]]
1229 -
1230 1230  = Create communication with **Omron PLC** =
1231 1231  
1232 -== **CP1 Series Protocol ** ==
1081 +== **CP1 Series Protocols** ==
1233 1233  
1234 1234  [[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CP1%20Series.zip]]
1235 1235  
1236 -== **CP2M Series Protocol** ==
1085 +== **CP2M Series Protocols** ==
1237 1237  
1238 1238  [[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CJ2M.zip]]
1239 1239  
1089 += Create communication with **Modbus RTU** =
1240 1240  
1241 -== **EC55 Series Protocol** ==
1091 +== **V-BOX as Slave** ==
1242 1242  
1243 -Supported device: EC55 temperature instrument
1244 -
1245 -**1)V-BOX Settings**
1246 -
1247 -|**Items**|**Settings**|**Note**
1248 -|Protocol|Omron EC55|
1249 -|Connection|RS485 (9600, 2, 7, EVEN)|
1250 -|Port No.|None|
1251 -|PLC station No.|0|
1252 -
1253 -**2)Address List**
1254 -
1255 -|**Type**|**Register**|**Device range**|**HMI range**|**Function**
1256 -|(% rowspan="3" %)Double word|C0|0-13 (Hex)|0-19|Set read only parameter for area 0
1257 -|C1|0-4D(Hex)|0-77|Set Read/Write parameter for area 0
1258 -|C3|0-CD(Hex)|0-205|Set Read/Write parameter for area 1
1259 -|(% rowspan="6" %)Word|80|0-13(Hex)|0-19|Set read only parameter in area 0
1260 -|81|0-4D(Hex)|0-77|Set Read/Write parameter in area 0
1261 -|83|0-CD(Hex)|0-205|Set Read/Write parameter in area 1
1262 -|CP|-|0-6|Read controller intrinsic property
1263 -|CS|-|0-2|Read controller states
1264 -|CA|-|0-17|Action command
1265 -
1266 -**3)Device Settings**
1267 -
1268 -Omron E5CC PLC configuration
1269 -
1270 -After entering the Communication Settings menu, please set the parameters to the default values for the following table. Press the cycle key of the instrument to enter the next setting.
1271 -
1272 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_3d95e093792ba98a.png?width=550&height=229&rev=1.1||alt="12.PLC Protocol_html_3d95e093792ba98a.png" height="229" width="550"]]
1273 -
1274 -According to PLC configuration and communication port configuration information of the HMI, provide the corresponding steps and configuration screenshots. This configuration needs to communicate properly with the above PLC configuration. The project settings are as follows
1275 -
1276 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_be583aa69dd6cf4c.png?width=550&height=242&rev=1.1||alt="12.PLC Protocol_html_be583aa69dd6cf4c.png" height="242" width="550"]]
1277 -
1278 -**✎Note:** The communication settings for HMI should be consistent with this setting.
1279 -
1280 -**4)Configure the communication protocol**
1281 -
1282 -[[image:image-20220831161041-1.png]]
1283 -
1284 -**5)Cable Wiring**
1285 -
1286 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1||alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
1287 -
1288 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1||alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
1289 -
1290 -**✎Note:**
1291 -
1292 -* COM3 only available in PI8000/PI9000 series.
1293 -* CA address could not support continuous writing function;
1294 -* Because of CP address intrinsic property: read control intrinsic property, so please place the character input part in use. Set address with CP0 and character length 10, used to display controller type. And place a number input part, set address with CP5 (cache size). Do not place other CP type address without CP0 in screen, otherwise CP type address is invalid
1295 -* When set value into read & write address, it is necessary to switch the temperature instrument meter to the corresponding interface according to the menu of the instrument where the address locates, so that the value could be written, otherwise, the value could not be written; When the communication write setting of the instrument is turned off, the writing function is invalid. Writing function could be opened by using the 00 address of the CA register, which write 01 value.
1296 -* When continuous writing of a value to a read-write address, please make sure all continuous writing address could be written. Otherwise, if one of these addresses could not be written, then all continuous writing commands will fail.
1297 -* Because of the mechanism problem, this protocol could not support CompoWay/F function that is read-write function of variables in protocol document.
1298 -* When using double-word address, set the data format to 32 bits, otherwise the read/write function is unable.
1299 -* Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
1300 -* [[image:image-20220831161356-1.png]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
1301 -
1302 -= Create communication with Xinje** PLC** =
1303 -
1304 -== **XC serial protocol** ==
1305 -
1306 -**1)V-BOX Settings**
1307 -
1308 -|**Item**|**Settings**|**Note**
1309 -|Protocol|XINJE XC MODBUS|
1310 -|Connection|RS232|
1311 -|Baud rate|19200|
1312 -|Data bit|8|
1313 -|Parity|EVEN|
1314 -|Stop bit|1|
1315 -|PLC station No.|1|
1316 -
1317 -**2)Address List**
1318 -
1319 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1320 -|Bit|M|M|M d|0~~8511|
1321 -|Bit|X|X|X o|0~~1747|
1322 -|Bit|Y|Y|Y o|0~~1747|
1323 -|Bit|S|S|S d|0~~1023|
1324 -|Bit|T|T|T d|0~~4095|
1325 -|Bit|C|C|C d|0~~634|
1326 -|Word|D|D|D d|0~~8511|
1327 -|Word|TD|TD|TD d|0~~618|
1328 -|Word|CD|CD|CD d|0~~634|
1329 -|Word|FD|FD|FD d|0~~8511|
1330 -
1331 -**3)Configure the communication protocol**
1332 -
1333 -
1334 -[[image:image-20220831163041-1.png]]
1335 -
1336 -**4)Cable Wiring**
1337 -
1338 -Figure
1339 -
1340 -[[image:image-20220831163406-2.png]][[image:image-20220831163422-3.png]]
1341 -
1342 -Pin Definition Diagram
1343 -
1344 -[[image:image-20220831163441-4.png]]
1345 -
1346 -== **XD serial protocol** ==
1347 -
1348 -**1)V-BOX Settings**
1349 -
1350 -Supported Series: Delta Xinjie XD/XE Series PLC
1351 -
1352 -|**Item**|**Settings**|**Note**
1353 -|Protocol|XINJE XD/XC MODBUS|
1354 -|Connection|RS232|
1355 -|Baud rate|19200|
1356 -|Data bit|8|
1357 -|Parity|EVEN|
1358 -|Stop bit|1|
1359 -|PLC station No.|1|
1360 -
1361 -**2)Address List**
1362 -
1363 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1364 -|Bit|M|M|M d|0~~74999|
1365 -|Bit|X1xx|X1xx|X1xx o|0~~1177|
1366 -|Bit|X2xx|X2xx|X2xx o|0~~277|
1367 -|Bit|X|X|X o|0~~77|
1368 -|Bit|Y1xx|Y1xx|Y1xx o|0~~1177|
1369 -|Bit|Y2xx|Y2xx|Y2xx o|0~~277|
1370 -|Bit|Y|Y|Y o|0~~4095|
1371 -|Bit|SM|SM|SM d|0~~4999|(((
1372 -
1373 -)))
1374 -|Bit|T|T|T d|0~~4999|
1375 -|Bit|C|C|C d|0~~4999|
1376 -|Bit|ET|ET|ET d|0~~31|
1377 -|Bit|SE|SE|SE d|0~~31|
1378 -|Bit|HM|HM|HM d|0~~11999|
1379 -|Bit|HSC|HSC|HSC d|0~~39|
1380 -|Bit|HS|HS|HS d|0~~999|
1381 -|Bit|HT|HT|HT d|0~~1999|
1382 -|Bit|HC|HC|HC d|0~~1999|
1383 -|Bit|S|S|S d|0~~7999|
1384 -|Word|D|D|D d|0~~69999|
1385 -|Word|ID|ID|ID d|0~~99|
1386 -|Word|ID1xx|ID1xx|ID1xx d|0~~999|
1387 -|Word|ID2xx|ID2xx|ID2xx d|0~~299|
1388 -|Word|QD|QD|QD d|0~~99|
1389 -|Word|QD1xx|QD1xx|QD1xx d|0~~999|
1390 -|Word|QD2xx|QD2xx|QD2xx d|0~~299|
1391 -|Word|SD|SD|SD d|0~~4999|
1392 -|Word|TD|TD|TD d|0~~575|
1393 -|Word|CD|CD|CD d|0~~575|
1394 -|Word|ETD|ETD|ETD d|0~~31|
1395 -|Word|HD|HD|HD d|0~~24999|
1396 -|Word|HSD|HSD|HSD d|0~~1023|
1397 -|Word|HTD|HTD|HTD d|0~~95|
1398 -|Word|HCD|HCD|HCD d|0~~95|
1399 -|Word|HSCD|HSCD|HSCD d|0~~31|
1400 -|Word|FD|FD|FD d|0~~8191|
1401 -|Word|SFD|SFD|SFD d|0~~5999|
1402 -|Word|FS|FS|FS d|0~~47|
1403 -
1404 -**3)Configure the communication protocol**
1405 -
1406 -[[image:image-20220831163923-7.png]]
1407 -
1408 -
1409 -
1410 -**4)Cable Wiring**
1411 -
1412 -Figure
1413 -
1414 -[[image:image-20220831163406-2.png]][[image:image-20220831163553-6.png]]
1415 -
1416 -Pin Definition Diagram
1417 -
1418 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
1419 -
1420 -
1421 -= Create communication with **Schneider PLC** =
1422 -
1423 -== **Schneider MODBUS RTU** ==
1424 -
1425 -**1)V-BOX Setting**
1426 -
1427 -|=**Parameters**|=**Recommended**|=**Notes**
1428 -|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
1429 -|**Connection**|RS485|
1430 -|**Baud rate**|19200|
1431 -|**Data bit**|8|
1432 -|**Parity**|Even|
1433 -|**Stop bit**|1|
1434 -|**PLC station No.**|1|
1435 -
1436 -**2)Address List**
1437 -
1438 -|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
1439 -|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
1440 -|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
1441 -|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
1442 -|W|MW|DDDDDD|0 ~~ 999999|Output register
1443 -|DW|MD|DDDDDD|0 ~~ 999999|Output register
1444 -
1445 -**3)Configure the communication protocol**
1446 -
1447 -[[image:image-20220902104329-1.png]]
1448 -
1449 -**4)Cable Wiring**
1450 -
1451 -**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
1452 -
1453 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
1454 -
1455 -= Create communication with Inovance** PLC** =
1456 -
1457 -== **H3U serial protocol** ==
1458 -
1459 -**1)V-BOX Settings**
1460 -
1461 -|**Item**|**Settings**|**Note**
1462 -|Protocol|INOVANCE H3U PLC|
1463 -|Connection|RS422|
1464 -|Baud rate|9600|
1465 -|Data bit|7|
1466 -|Parity|EVEN|
1467 -|Stop bit|1|
1468 -|PLC station No.|0|
1469 -
1470 -**2)Address List**
1471 -
1472 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1473 -|Bit|X|X|X o|0~~303237|
1474 -|Bit|Y|Y|Y o|0~~303237|
1475 -|Bit|M|M|M d|0~~99999|
1476 -|Bit|T|T|T d|0~~99999|
1477 -|Bit|C|C|C d|0~~99999|
1478 -|Bit|SM|SM|SM d|8000~~999|
1479 -|Bit|S|T|S d|0~~99999|
1480 -|Bit|Lamp|Lamp|Lamp d|0~~0|
1481 -|Word|X|X|X o|0~~303237|
1482 -|Word|Y|Y|Y o|0~~303237|
1483 -|Word|M|M|M d|0~~99999|
1484 -|Word|T|T|T d|0~~99999|
1485 -|Word|C|C|C d|0~~199|
1486 -|Word|D|D|D d|0~~7999|
1487 -|Word|S|S|S d|0~~99999|
1488 -|Word|SD|SD|SD d|8000~~9999|
1489 -|Word|R|R|R d|0~~32767|
1490 -
1491 -**3)Configure the communication protocol**
1492 -
1493 -[[image:image-20220831164626-1.png]]
1494 -
1495 -
1496 -
1497 -**4)Cable Wiring**
1498 -
1499 -Figure
1500 -
1501 -[[image:image-20220831164646-2.png]][[image:image-20220831164700-3.png]]
1502 -
1503 -Pin Definition Diagram
1504 -
1505 -[[image:image-20220831164731-4.png]]
1506 -
1507 -= Create communication with Panasonic** PLC** =
1508 -
1509 -== **FP serial protocol** ==
1510 -
1511 -**1)V-BOX Settings**
1512 -
1513 -|**Item**|**Settings**|**Note**
1514 -|Protocol|Panasonic FP MFWTOCOL|
1515 -|Connection|RS232|
1516 -|Baud rate|9600|
1517 -|Data bit|8|
1518 -|Parity|ODD|
1519 -|Stop bit|1|
1520 -|PLC station No.|1|
1521 -
1522 -**2)Address List**
1523 -
1524 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1525 -|Bit|X|X|X d|0~~9999|
1526 -|Bit|Y|Y|Y d|0~~9999|
1527 -|Bit|R|R|R d|0~~9999|
1528 -|Bit|T|T|T d|0~~9999|
1529 -|Bit|C|C|C d|0~~9999|
1530 -|Bit|L|L|L d|0~~9999|
1531 -|Word|WX|WX|WX d|0~~9999|
1532 -|Word|WY|WY|WY d|0~~9999|
1533 -|Word|WR|WR|WR d|0~~9999|
1534 -|Word|WL|WL|WL d|0~~9999|
1535 -|Word|LD|LD|LD d|0~~9999|
1536 -|Word|DT|DT|DT d|0~~65535|
1537 -|Word|FL|FL|FL d|0~~9999|
1538 -|Word|EV|EV|EV d|0~~9999|
1539 -|Word|SV|SV|SV d|0~~9999|
1540 -
1541 -**3)Configure the communication protocol**
1542 -
1543 -[[image:image-20220831165238-4.png]]
1544 -
1545 -
1546 -
1547 -**4)Cable Wiring**
1548 -
1549 -Figure
1550 -
1551 -[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
1552 -
1553 -Pin Definition Diagram
1554 -
1555 -[[image:image-20220831165008-1.png]]
1556 -
1557 -= Create communication with LS** PLC** =
1558 -
1559 -== **XBC serial protocol** ==
1560 -
1561 -**1)V-BOX Settings**
1562 -
1563 -|**Item**|**Settings**|**Note**
1564 -|Protocol|LS XBC CNet|
1565 -|Connection|RS232|
1566 -|Baud rate|115200|
1567 -|Data bit|8|
1568 -|Parity|NONE|
1569 -|Stop bit|1|
1570 -|PLC station No.|1|
1571 -
1572 -**2)Address List**
1573 -
1574 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1575 -|Bit|P|P|P d|0~~2047|
1576 -|Bit|M|M|M d|0~~2047|
1577 -|Bit|L|L|L d|0~~11263|
1578 -|Bit|K|K|K d|0~~16183|
1579 -|Bit|F|F|F d|0~~2047|
1580 -|Bit|D|D|D d|0~~32767|
1581 -|Bit|R|R|R d|0~~32767|
1582 -|Bit|U|U|U d|0~~4095|
1583 -|Word|P|P|P d|0~~2047|
1584 -|Word|M|M|M d|0~~2047|
1585 -|Word|L|L|L d|0~~11263|
1586 -|Word|K|K|K d|0~~16183|
1587 -|Word|F|F|F d|0~~2047|
1588 -|Word|C|C|C d|0~~2047|
1589 -|Word|T|T|T d|0~~2047|
1590 -|Word|D|D|D d|0~~32767|
1591 -|Word|N|N|N d|0~~21503|
1592 -|Word|R|R|R d|0~~32767|
1593 -|Word|U|U|U d|0~~4095|
1594 -|Word|Z|Z|Z d|0~~127|
1595 -|Word|S|S|S d|0~~127|
1596 -
1597 -**3)Configure the communication protocol**
1598 -
1599 -[[image:image-20220831170147-1.png]]
1600 -
1601 -**4)Cable Wiring**
1602 -
1603 -Figure
1604 -
1605 -[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
1606 -
1607 -Pin Definition Diagram
1608 -
1609 -[[image:image-20220831170215-2.png]]
1610 -
1611 -== **XGK FEnet Ethernet protocol** ==
1612 -
1613 -Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
1614 -
1615 -**1)V-BOX Settings**
1616 -
1617 -|**Items**|**Settings**|**Note**
1618 -|Protocol|LG XGK FEnet(Ethernet)|
1619 -|Connection|Ethernet|
1620 -|Port No.|2004|
1621 -
1622 -**2)Address List**
1623 -
1624 -|**Type**|**Register**|**Range**|**Format**|**Note**
1625 -|(% rowspan="14" %)Word|P|0~~2047|P d|
1626 -|M|0~~2047|M d|
1627 -|K|0~~2047|K d|
1628 -|F|0~~2047|F d|
1629 -|T|0~~2047|T d|
1630 -|C|0~~2047|C d|
1631 -|Z|0~~127|Z d|
1632 -|S|0~~127|S d|
1633 -|L|0~~11263|L d|
1634 -|N|0~~21503|N d|
1635 -|D|0~~32767|D d|
1636 -|R|0~~32767|R d|
1637 -|ZR|0~~65535|ZR d|
1638 -|UxDD|0~~6331|UxDD nndd|nn: 0~~63, dd: 0~~31
1639 -
1640 -**✎Note:**
1641 -
1642 -* In addition to the "UxDD" register, the others correspond to the PLC register one by one. UxDD corresponds to U in the PLC;
1643 -* The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
1644 -* All bit registers are in the form of bits in word, and the range is the same as the word register;
1645 -
1646 -**3)Communication Settings**
1647 -
1648 -[[image:image-20220831171127-1.png]]
1649 -
1650 -**4)Cable Wiring**
1651 -
1652 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1653 -
1654 -= Create communication with **Modbus ** =
1655 -
1656 -== **MODBUS RTU Slave (All function)** ==
1657 -
1658 1658  Select the protocol "Modbus RTU Slave (All Fuction)",
1659 1659  
1660 1660  Then set baud rate, port, stop bits, data bits, parity.
... ... @@ -1662,7 +1662,7 @@
1662 1662  (% style="text-align:center" %)
1663 1663  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
1664 1664  
1665 -== **MODBUS RTU Master** ==
1100 +== **V-BOX as Master** ==
1666 1666  
1667 1667  Select the protocol "Modbus RTU Master",
1668 1668  
... ... @@ -1698,61 +1698,6 @@
1698 1698  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
1699 1699  |0F (Write multiple bits)
1700 1700  
1701 -== **MODBUS TCP Slave (All function)** ==
1702 -
1703 -Supported series: MODBUS TCP controller
1704 -
1705 -V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
1706 -
1707 -**1)V-BOX Setting**
1708 -
1709 -|**Items**|**Settings**|**Note**
1710 -|Protocol|MODBUS TCP Slave (All function)|
1711 -|Connection|Ethernet|
1712 -|Port No.|502|
1713 -|PLC station No.|1
1714 -
1715 -**2)Address List**
1716 -
1717 -|**Type**|**Register**|**Function code & Description**
1718 -|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
1719 -|06 (write single register: write a binary value to a holding register)
1720 -|10 (write values to multiple addresses )
1721 -|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
1722 -|06 (write single register: write a binary value to a holding register)
1723 -|10 (write values to multiple addresses )
1724 -|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
1725 -|06 (write single register: write a binary value to a holding register)
1726 -|10 (write values to multiple addresses )
1727 -|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
1728 -|10 (write values to multiple addresses )
1729 -|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
1730 -|05 (Force a single coil to force the on/off state of a logic coil)
1731 -|0F (Write multiple bits, ie write continuously)
1732 -|(% rowspan="3" %)1|02 (Read the input state)
1733 -|05 (Force a single coil to force the on/off state of a logic coil)
1734 -|0F (Write multiple bits)
1735 -|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
1736 -|05 (Force a single coil to force the on/off state of a logic coil)
1737 -|0F (Write multiple bits)
1738 -|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
1739 -|0F (Write multiple bits)
1740 -
1741 -**3)Communication Settings**
1742 -
1743 -Configure V-BOX Ethernet IP in Networking Settings
1744 -
1745 -[[image:image-20220902111833-3.png]]
1746 -
1747 -
1748 -Configure PLC Ethernet IP in Communication;
1749 -
1750 -[[image:image-20220902111121-1.png]]
1751 -
1752 -**4)Cable Wiring**
1753 -
1754 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1755 -
1756 1756  == **communicate with VB inverter** ==
1757 1757  
1758 1758  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]
image-20220831155101-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -34.6 KB
Content
image-20220831155129-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -44.9 KB
Content
image-20220831155157-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -20.8 KB
Content
image-20220831160010-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -59.6 KB
Content
image-20220831160055-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -51.5 KB
Content
image-20220831161041-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.1 KB
Content
image-20220831161356-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -27.0 KB
Content
image-20220831163041-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.6 KB
Content
image-20220831163406-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.4 KB
Content
image-20220831163422-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -53.9 KB
Content
image-20220831163441-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.7 KB
Content
image-20220831163548-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20220831163553-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20220831163923-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.3 KB
Content
image-20220831164626-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -56.1 KB
Content
image-20220831164646-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.4 KB
Content
image-20220831164700-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -66.6 KB
Content
image-20220831164731-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -12.3 KB
Content
image-20220831165008-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
image-20220831165017-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -36.2 KB
Content
image-20220831165031-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.3 KB
Content
image-20220831165238-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.4 KB
Content
image-20220831170147-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.1 KB
Content
image-20220831170215-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -14.3 KB
Content
image-20220831170254-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -43.5 KB
Content
image-20220831170306-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.5 KB
Content
image-20220831171127-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.1 KB
Content
image-20220902104329-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.7 KB
Content
image-20220902111121-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.9 KB
Content
image-20220902111754-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.6 KB
Content
image-20220902111833-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -56.1 KB
Content