Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 173.1
edited by Bob
on 2022/11/16 11:00
Change comment: There is no comment for this version
To version 164.1
edited by Ben
on 2022/09/02 11:24
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Bob
1 +XWiki.Ben
Content
... ... @@ -704,101 +704,6 @@
704 704  [[image:image-20220825100845-4.png]]
705 705  
706 706  
707 -== **FX3U Ethernet Protocol** ==
708 -
709 - Mitsubishi FX3U series PLC
710 -
711 -**HMI Settings**
712 -
713 -|Items|Settings|Note
714 -|Protocol|Mitsubishi FX3U|
715 -|Connection|Ethernet|
716 -|Port No.|5009|Must be the same as the PLC setting
717 -|PLC station No.|0|
718 -
719 -**Address List**
720 -
721 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
722 -|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
723 -|Y|Y|Y OOO|0~~377|
724 -|M|M|M DDDD|0~~7679|
725 -|SM|SM|SM DDDD|8000~~8511|
726 -|S|S|S DDDD|0~~4095|
727 -|TS|TS|TS DDD|0~~511|
728 -|CS|CS|CS DDD|0~~255|
729 -|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
730 -|TN|TN|TN DDD|0~~511|
731 -|D|D|D DDDD|0~~7999|
732 -|SD|SD|SD DDDD|8000~~8511|
733 -|R|R|R DDDDD|0~~32767|
734 -
735 -**1)Ethernet Module Settings**
736 -
737 -FX3U-ENET-L module configuration
738 -Set up the FX3U-ENET-L Ethernet module settings as follows.
739 -Select the module location, which in this document is Module 0.
740 -
741 -[[image:image-20221116105850-1.png]]
742 -
743 -Select "Operational setting" to enter the following screen.
744 -
745 -The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
746 -
747 -[[image:image-20221116105947-1.png]]
748 -
749 -
750 -Select "Open setting" to enter the setting interface, the settings are as follows.
751 -
752 -The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
753 -
754 -Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
755 -
756 -
757 -
758 -Click on "transter setup" - "PC side I/F setting", see the following figure.
759 -
760 -After setting, the first download must use the programming cable, as shown in the figure; after that, can
761 -
762 -use the IP set in the "Ethernet board" to communicate directly with the network cable.
763 -
764 -
765 -
766 -Read and write data from the Ethernet module
767 -
768 -
769 -
770 -Set "Transter setup" to COM communication, and read or write operation as shown below
771 -
772 -
773 -
774 -**PLC Settings (GX Works 2)**
775 -
776 -Create a blank FX5U project
777 -
778 -Find Current Connection in the navigation
779 -
780 -
781 -
782 -Select Connection Channel List
783 -
784 -Select Ethernet board communication
785 -
786 -
787 -
788 -Select Ethernet Module
789 -Set the IP address of the PLC
790 -
791 -
792 -
793 -Read or write PLC data, in this document is read
794 -
795 -
796 -
797 -**V-BOX Communication Setting**
798 -
799 -
800 -
801 -
802 802  == **FX5U Serial Protocol** ==
803 803  
804 804  Mitsubishi FX5U series PLC
... ... @@ -953,10 +953,11 @@
953 953  
954 954  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
955 955  
956 -**5）Cable Wiring**
861 +**5）电缆布线**
957 957  
958 958  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
959 959  
865 +
960 960  == **L02 Serial Protocol** ==
961 961  
962 962  Mitsubishi L02 series CPU built-in serial port.
image-20221116105850-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.9 KB
Content
image-20221116105947-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.7 KB
Content