Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 173.1
edited by Bob
on 2022/11/16 11:00
Change comment: There is no comment for this version
To version 171.1
edited by Bob
on 2022/11/16 10:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -732,19 +732,20 @@
732 732  |SD|SD|SD DDDD|8000~~8511|
733 733  |R|R|R DDDDD|0~~32767|
734 734  
735 -**1)Ethernet Module Settings**
735 +**Ethernet Module Settings**
736 736  
737 737  FX3U-ENET-L module configuration
738 738  Set up the FX3U-ENET-L Ethernet module settings as follows.
739 739  Select the module location, which in this document is Module 0.
740 740  
741 -[[image:image-20221116105850-1.png]]
741 +[[image:image-20221116094003-1.png]]
742 742  
743 +
743 743  Select "Operational setting" to enter the following screen.
744 744  
745 745  The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
746 746  
747 -[[image:image-20221116105947-1.png]]
748 +[[image:image-20221116094019-2.png]]
748 748  
749 749  
750 750  Select "Open setting" to enter the setting interface, the settings are as follows.
... ... @@ -753,6 +753,7 @@
753 753  
754 754  Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
755 755  
757 +[[image:image-20221116094038-3.png]]
756 756  
757 757  
758 758  Click on "transter setup" - "PC side I/F setting", see the following figure.
... ... @@ -761,14 +761,17 @@
761 761  
762 762  use the IP set in the "Ethernet board" to communicate directly with the network cable.
763 763  
766 +[[image:image-20221116094122-4.png||height="422" width="707"]]
764 764  
765 765  
766 766  Read and write data from the Ethernet module
767 767  
771 +[[image:image-20221116094131-5.png||height="551" width="708"]]
768 768  
769 769  
770 770  Set "Transter setup" to COM communication, and read or write operation as shown below
771 771  
776 +[[image:image-20221116094150-6.png]]
772 772  
773 773  
774 774  **PLC Settings (GX Works 2)**
... ... @@ -777,6 +777,7 @@
777 777  
778 778  Find Current Connection in the navigation
779 779  
785 +[[image:image-20221116094206-7.png||height="425" width="711"]]
780 780  
781 781  
782 782  Select Connection Channel List
... ... @@ -783,20 +783,25 @@
783 783  
784 784  Select Ethernet board communication
785 785  
792 +[[image:image-20221116094709-9.png||height="427" width="715"]]
786 786  
787 787  
788 788  Select Ethernet Module
789 789  Set the IP address of the PLC
790 790  
798 +[[image:image-20221116094736-11.png||height="682" width="716"]]
791 791  
792 792  
793 793  Read or write PLC data, in this document is read
794 794  
803 +[[image:image-20221116094755-12.png||height="426" width="715"]]
795 795  
805 +[[image:image-20221116094803-13.png||height="427" width="715"]]
796 796  
797 797  **V-BOX Communication Setting**
798 798  
799 799  
810 +
800 800  
801 801  
802 802  == **FX5U Serial Protocol** ==
image-20221116105850-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.9 KB
Content
image-20221116105947-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.7 KB
Content