Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 173.1
edited by Bob
on 2022/11/16 11:00
Change comment: There is no comment for this version
To version 174.1
edited by Bob
on 2022/11/16 11:09
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -708,7 +708,7 @@
708 708  
709 709   Mitsubishi FX3U series PLC
710 710  
711 -**HMI Settings**
711 +**1)HMI Settings**
712 712  
713 713  |Items|Settings|Note
714 714  |Protocol|Mitsubishi FX3U|
... ... @@ -716,7 +716,7 @@
716 716  |Port No.|5009|Must be the same as the PLC setting
717 717  |PLC station No.|0|
718 718  
719 -**Address List**
719 +**2)Address List**
720 720  
721 721  |**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
722 722  |(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
... ... @@ -732,7 +732,7 @@
732 732  |SD|SD|SD DDDD|8000~~8511|
733 733  |R|R|R DDDDD|0~~32767|
734 734  
735 -**1)Ethernet Module Settings**
735 +**3)Ethernet Module Settings**
736 736  
737 737  FX3U-ENET-L module configuration
738 738  Set up the FX3U-ENET-L Ethernet module settings as follows.
... ... @@ -746,7 +746,6 @@
746 746  
747 747  [[image:image-20221116105947-1.png]]
748 748  
749 -
750 750  Select "Open setting" to enter the setting interface, the settings are as follows.
751 751  
752 752  The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
... ... @@ -753,8 +753,8 @@
753 753  
754 754  Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
755 755  
755 +[[image:image-20221116110802-1.png]]
756 756  
757 -
758 758  Click on "transter setup" - "PC side I/F setting", see the following figure.
759 759  
760 760  After setting, the first download must use the programming cable, as shown in the figure; after that, can
... ... @@ -761,18 +761,18 @@
761 761  
762 762  use the IP set in the "Ethernet board" to communicate directly with the network cable.
763 763  
763 +[[image:image-20221116110832-2.png||height="423" width="708"]]
764 764  
765 -
766 766  Read and write data from the Ethernet module
767 767  
767 +[[image:image-20221116110907-3.png]]
768 768  
769 -
770 770  Set "Transter setup" to COM communication, and read or write operation as shown below
771 771  
771 +[[image:image-20221116110917-4.png]]
772 772  
773 +**4)PLC Settings (GX Works 2)**
773 773  
774 -**PLC Settings (GX Works 2)**
775 -
776 776  Create a blank FX5U project
777 777  
778 778  Find Current Connection in the navigation
image-20221116110802-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bob
Size
... ... @@ -1,0 +1,1 @@
1 +16.4 KB
Content
image-20221116110832-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bob
Size
... ... @@ -1,0 +1,1 @@
1 +42.2 KB
Content
image-20221116110907-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bob
Size
... ... @@ -1,0 +1,1 @@
1 +17.8 KB
Content
image-20221116110917-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bob
Size
... ... @@ -1,0 +1,1 @@
1 +23.2 KB
Content