Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54

From 145.1 to 144.1 From 175.1 to 174.1

From version 174.1

edited by Bob
on 2022/11/16 11:09

Change comment: There is no comment for this version

To version 145.1

edited by Ben
on 2022/08/31 16:15

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 30 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Bob
++XWiki.Ben

Content

@@ -182,7 +182,7 @@
  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
--**1）V-BOX setting**
++**1）PLC Settings**
  |**Item**|**Settings**|**Note**
  |Protocol|Allen-Bradlley DF1 Advanced|
@@ -436,7 +436,7 @@
  Supported Series: Siemens S7-300 series PLC
--**1）V-BOX setting**
++**1）PLC Setting**
  |**Items**|**Settings**|**Note**
  |Protocol|Simens S7-300 Ethernet|
@@ -498,7 +498,7 @@
  Supported Series: Siemens S7-400, S7-1200 and S7-1500
--**1）V-BOX setting**
++**1）PLC Setting**
  |=**Items**|=**Settings**|=**Note**
  |Protocol|Siemens S7-XXX|
@@ -704,100 +704,6 @@
  [[image:image-20220825100845-4.png]]
--== **FX3U Ethernet Protocol** ==
--
-- Mitsubishi FX3U series PLC
--
--**1)HMI Settings**
--
--|Items|Settings|Note
--|Protocol|Mitsubishi FX3U|
--|Connection|Ethernet|
--|Port No.|5009|Must be the same as the PLC setting
--|PLC station No.|0|
--
--**2)Address List**
--
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
--|Y|Y|Y OOO|0~~377|
--|M|M|M DDDD|0~~7679|
--|SM|SM|SM DDDD|8000~~8511|
--|S|S|S DDDD|0~~4095|
--|TS|TS|TS DDD|0~~511|
--|CS|CS|CS DDD|0~~255|
--|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
--|TN|TN|TN DDD|0~~511|
--|D|D|D DDDD|0~~7999|
--|SD|SD|SD DDDD|8000~~8511|
--|R|R|R DDDDD|0~~32767|
--
--**3)Ethernet Module Settings**
--
--FX3U-ENET-L module configuration
--Set up the FX3U-ENET-L Ethernet module settings as follows.
--Select the module location, which in this document is Module 0.
--
--[[image:image-20221116105850-1.png]]
--
--Select "Operational setting" to enter the following screen.
--
--The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
--
--[[image:image-20221116105947-1.png]]
--
--Select "Open setting" to enter the setting interface, the settings are as follows.
--
--The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
--
--Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
--
--[[image:image-20221116110802-1.png]]
--
--Click on "transter setup" - "PC side I/F setting", see the following figure.
--
--After setting, the first download must use the programming cable, as shown in the figure; after that, can
--
--use the IP set in the "Ethernet board" to communicate directly with the network cable.
--
--[[image:image-20221116110832-2.png||height="423" width="708"]]
--
--Read and write data from the Ethernet module
--
--[[image:image-20221116110907-3.png]]
--
--Set "Transter setup" to COM communication, and read or write operation as shown below
--
--[[image:image-20221116110917-4.png]]
--
--**4)PLC Settings (GX Works 2)**
--
--Create a blank FX5U project
--
--Find Current Connection in the navigation
--
--
--
--Select Connection Channel List
--
--Select Ethernet board communication
--
--
--
--Select Ethernet Module
--Set the IP address of the PLC
--
--
--
--Read or write PLC data, in this document is read
--
--
--
--**V-BOX Communication Setting**
--
--
--
--
  == **FX5U Serial Protocol** ==
  Mitsubishi FX5U series PLC
@@ -952,10 +952,11 @@
  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
--**5）Cable Wiring**
++**5）电缆布线**
  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
++
  == **L02 Serial Protocol** ==
  Mitsubishi L02 series CPU built-in serial port.
@@ -1287,362 +1287,66 @@
  * Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
  * [[image:image-20220831161356-1.png]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
--= Create communication with Xinje** PLC** =
++== **EtherNet/IP NX series Protocol** ==
--== **XC serial protocol** ==
++Supported series: Omron NX/NJ series
--**1）V-BOX Settings**
++**HMI Setting**
--|**Item**|**Settings**|**Note**
--|Protocol|XINJE XC MODBUS|
--|Connection|RS232|
--|Baud rate|19200|
--|Data bit|8|
--|Parity|EVEN|
--|Stop bit|1|
++|**Items**|**Settings**|**Note**
++|Protocol|Omron NX Ethernet/IP|
++|Connection|Ethernet|
++|Port No.|44818|
  |PLC station No.|1|
--**2）Address List**
++**Instruction**
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|Bit|M|M|M d|0~~8511|
--|Bit|X|X|X o|0~~1747|
--|Bit|Y|Y|Y o|0~~1747|
--|Bit|S|S|S d|0~~1023|
--|Bit|T|T|T d|0~~4095|
--|Bit|C|C|C d|0~~634|
--|Word|D|D|D d|0~~8511|
--|Word|TD|TD|TD d|0~~618|
--|Word|CD|CD|CD d|0~~634|
--|Word|FD|FD|FD d|0~~8511|
++1) In Sysmac Studio, please select [Publish Only] for [Network Publish] when setting address tag.
--**3）Configure the communication protocol**
++2) When [Do not publish] is selected for a tag, different import methods may lead to different results. When import tags by [Get Tags from Device], the tag will be eliminated. If [Import tags] is selected, the tags will be imported, but the communication will not succeed.
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_4156caf6f116c570.png?width=600&height=277&rev=1.1||alt="12.PLC Protocol_html_4156caf6f116c570.png" height="277" width="600"]]
--[[image:image-20220831163041-1.png]]
++**Export labels from Sysmac Studio**
--**4）Cable Wiring**
++Launch Sysmac Studio, under Global Variables create the address labels, and thenselect [Tools] -> [Export Global Variables];
--Figure
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_26f91dee66c723e9.png?width=600&height=276&rev=1.1||alt="12.PLC Protocol_html_26f91dee66c723e9.png" height="276" width="600"]]
--[[image:image-20220831163406-2.png]][[image:image-20220831163422-3.png]]
++Launch PIStudio, in [Communication] Settings add Omron NX Ethernet/IP protocol;
--Pin Definition Diagram
++Click [Label manage];
--[[image:image-20220831163441-4.png]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cd38d2d0c5187f6b.png?width=600&height=276&rev=1.1||alt="12.PLC Protocol_html_cd38d2d0c5187f6b.png" height="276" width="600"]]
--== **XD serial protocol** ==
++Click [Import labels] and then select the file exported in step 1;
--**1）V-BOX Settings**
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_52bd5da678bef9b4.png?width=600&height=403&rev=1.1||alt="12.PLC Protocol_html_52bd5da678bef9b4.png" height="403" width="600"]]
--Supported Series: Delta Xinjie XD/XE Series PLC
++The Import Status field shows the result, click [OK] to finish importing address labels;
--|**Item**|**Settings**|**Note**
--|Protocol|XINJE XD/XC MODBUS|
--|Connection|RS232|
--|Baud rate|19200|
--|Data bit|8|
--|Parity|EVEN|
--|Stop bit|1|
--|PLC station No.|1|
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_7f0465a589b98912.png?width=600&height=291&rev=1.1||alt="12.PLC Protocol_html_7f0465a589b98912.png" height="291" width="600"]]
--**2）Address List**
++**Communication Settings**
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|Bit|M|M|M d|0~~74999|
--|Bit|X1xx|X1xx|X1xx o|0~~1177|
--|Bit|X2xx|X2xx|X2xx o|0~~277|
--|Bit|X|X|X o|0~~77|
--|Bit|Y1xx|Y1xx|Y1xx o|0~~1177|
--|Bit|Y2xx|Y2xx|Y2xx o|0~~277|
--|Bit|Y|Y|Y o|0~~4095|
--|Bit|SM|SM|SM d|0~~4999|(((
--
--)))
--|Bit|T|T|T d|0~~4999|
--|Bit|C|C|C d|0~~4999|
--|Bit|ET|ET|ET d|0~~31|
--|Bit|SE|SE|SE d|0~~31|
--|Bit|HM|HM|HM d|0~~11999|
--|Bit|HSC|HSC|HSC d|0~~39|
--|Bit|HS|HS|HS d|0~~999|
--|Bit|HT|HT|HT d|0~~1999|
--|Bit|HC|HC|HC d|0~~1999|
--|Bit|S|S|S d|0~~7999|
--|Word|D|D|D d|0~~69999|
--|Word|ID|ID|ID d|0~~99|
--|Word|ID1xx|ID1xx|ID1xx d|0~~999|
--|Word|ID2xx|ID2xx|ID2xx d|0~~299|
--|Word|QD|QD|QD d|0~~99|
--|Word|QD1xx|QD1xx|QD1xx d|0~~999|
--|Word|QD2xx|QD2xx|QD2xx d|0~~299|
--|Word|SD|SD|SD d|0~~4999|
--|Word|TD|TD|TD d|0~~575|
--|Word|CD|CD|CD d|0~~575|
--|Word|ETD|ETD|ETD d|0~~31|
--|Word|HD|HD|HD d|0~~24999|
--|Word|HSD|HSD|HSD d|0~~1023|
--|Word|HTD|HTD|HTD d|0~~95|
--|Word|HCD|HCD|HCD d|0~~95|
--|Word|HSCD|HSCD|HSCD d|0~~31|
--|Word|FD|FD|FD d|0~~8191|
--|Word|SFD|SFD|SFD d|0~~5999|
--|Word|FS|FS|FS d|0~~47|
++Enable HMI Ethernet in [Project Settings];
--**3）Configure the communication protocol**
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_43b671f18153910d.png?width=405&height=107&rev=1.1||alt="12.PLC Protocol_html_43b671f18153910d.png" height="107" width="405"]]
--[[image:image-20220831163923-7.png]]
++Set PLC IP in [Device IP] settings;
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_437cb087b36b5784.png?width=600&height=330&rev=1.1||alt="12.PLC Protocol_html_437cb087b36b5784.png" height="330" width="600"]]
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_60ef71528a99abf5.png?width=554&height=188&rev=1.1||alt="12.PLC Protocol_html_60ef71528a99abf5.png" height="188" width="554"]]
--**4）Cable Wiring**
++**Cable Wiring**
--Figure
++[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
--[[image:image-20220831163406-2.png]][[image:image-20220831163553-6.png]]
++= Create communication with **Modbus RTU** =
--Pin Definition Diagram
++== **V-BOX as Slave** ==
--[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
--
--
--= Create communication with **Schneider PLC** =
--
--== **Schneider MODBUS RTU** ==
--
--**1）V-BOX Setting**
--
--|=**Parameters**|=**Recommended**|=**Notes**
--|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
--|**Connection**|RS485|
--|**Baud rate**|19200|
--|**Data bit**|8|
--|**Parity**|Even|
--|**Stop bit**|1|
--|**PLC station No.**|1|
--
--**2）Address List**
--
--|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
--|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
--|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
--|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
--|W|MW|DDDDDD|0 ~~ 999999|Output register
--|DW|MD|DDDDDD|0 ~~ 999999|Output register
--
--**3）Configure the communication protocol**
--
--[[image:image-20220902104329-1.png]]
--
--**4）Cable Wiring**
--
--**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
--
--[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
--
--= Create communication with Inovance** PLC** =
--
--== **H3U serial protocol** ==
--
--**1）V-BOX Settings**
--
--|**Item**|**Settings**|**Note**
--|Protocol|INOVANCE H3U PLC|
--|Connection|RS422|
--|Baud rate|9600|
--|Data bit|7|
--|Parity|EVEN|
--|Stop bit|1|
--|PLC station No.|0|
--
--**2）Address List**
--
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|Bit|X|X|X o|0~~303237|
--|Bit|Y|Y|Y o|0~~303237|
--|Bit|M|M|M d|0~~99999|
--|Bit|T|T|T d|0~~99999|
--|Bit|C|C|C d|0~~99999|
--|Bit|SM|SM|SM d|8000~~999|
--|Bit|S|T|S d|0~~99999|
--|Bit|Lamp|Lamp|Lamp d|0~~0|
--|Word|X|X|X o|0~~303237|
--|Word|Y|Y|Y o|0~~303237|
--|Word|M|M|M d|0~~99999|
--|Word|T|T|T d|0~~99999|
--|Word|C|C|C d|0~~199|
--|Word|D|D|D d|0~~7999|
--|Word|S|S|S d|0~~99999|
--|Word|SD|SD|SD d|8000~~9999|
--|Word|R|R|R d|0~~32767|
--
--**3）Configure the communication protocol**
--
--[[image:image-20220831164626-1.png]]
--
--
--
--**4）Cable Wiring**
--
--Figure
--
--[[image:image-20220831164646-2.png]][[image:image-20220831164700-3.png]]
--
--Pin Definition Diagram
--
--[[image:image-20220831164731-4.png]]
--
--= Create communication with Panasonic** PLC** =
--
--== **FP serial protocol** ==
--
--**1）V-BOX Settings**
--
--|**Item**|**Settings**|**Note**
--|Protocol|Panasonic FP MFWTOCOL|
--|Connection|RS232|
--|Baud rate|9600|
--|Data bit|8|
--|Parity|ODD|
--|Stop bit|1|
--|PLC station No.|1|
--
--**2）Address List**
--
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|Bit|X|X|X d|0~~9999|
--|Bit|Y|Y|Y d|0~~9999|
--|Bit|R|R|R d|0~~9999|
--|Bit|T|T|T d|0~~9999|
--|Bit|C|C|C d|0~~9999|
--|Bit|L|L|L d|0~~9999|
--|Word|WX|WX|WX d|0~~9999|
--|Word|WY|WY|WY d|0~~9999|
--|Word|WR|WR|WR d|0~~9999|
--|Word|WL|WL|WL d|0~~9999|
--|Word|LD|LD|LD d|0~~9999|
--|Word|DT|DT|DT d|0~~65535|
--|Word|FL|FL|FL d|0~~9999|
--|Word|EV|EV|EV d|0~~9999|
--|Word|SV|SV|SV d|0~~9999|
--
--**3）Configure the communication protocol**
--
--[[image:image-20220831165238-4.png]]
--
--
--
--**4）Cable Wiring**
--
--Figure
--
--[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
--
--Pin Definition Diagram
--
--[[image:image-20220831165008-1.png]]
--
--= Create communication with LS** PLC** =
--
--== **XBC serial protocol** ==
--
--**1）V-BOX Settings**
--
--|**Item**|**Settings**|**Note**
--|Protocol|LS XBC CNet|
--|Connection|RS232|
--|Baud rate|115200|
--|Data bit|8|
--|Parity|NONE|
--|Stop bit|1|
--|PLC station No.|1|
--
--**2）Address List**
--
--|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
--|Bit|P|P|P d|0~~2047|
--|Bit|M|M|M d|0~~2047|
--|Bit|L|L|L d|0~~11263|
--|Bit|K|K|K d|0~~16183|
--|Bit|F|F|F d|0~~2047|
--|Bit|D|D|D d|0~~32767|
--|Bit|R|R|R d|0~~32767|
--|Bit|U|U|U d|0~~4095|
--|Word|P|P|P d|0~~2047|
--|Word|M|M|M d|0~~2047|
--|Word|L|L|L d|0~~11263|
--|Word|K|K|K d|0~~16183|
--|Word|F|F|F d|0~~2047|
--|Word|C|C|C d|0~~2047|
--|Word|T|T|T d|0~~2047|
--|Word|D|D|D d|0~~32767|
--|Word|N|N|N d|0~~21503|
--|Word|R|R|R d|0~~32767|
--|Word|U|U|U d|0~~4095|
--|Word|Z|Z|Z d|0~~127|
--|Word|S|S|S d|0~~127|
--
--**3）Configure the communication protocol**
--
--[[image:image-20220831170147-1.png]]
--
--**4）Cable Wiring**
--
--Figure
--
--[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
--
--Pin Definition Diagram
--
--[[image:image-20220831170215-2.png]]
--
--== **XGK FEnet Ethernet protocol** ==
--
--Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
--
--**1）V-BOX Settings**
--
--|**Items**|**Settings**|**Note**
--|Protocol|LG XGK FEnet(Ethernet)|
--|Connection|Ethernet|
--|Port No.|2004|
--
--**2）Address List**
--
--|**Type**|**Register**|**Range**|**Format**|**Note**
--|(% rowspan="14" %)Word|P|0~~2047|P d|
--|M|0~~2047|M d|
--|K|0~~2047|K d|
--|F|0~~2047|F d|
--|T|0~~2047|T d|
--|C|0~~2047|C d|
--|Z|0~~127|Z d|
--|S|0~~127|S d|
--|L|0~~11263|L d|
--|N|0~~21503|N d|
--|D|0~~32767|D d|
--|R|0~~32767|R d|
--|ZR|0~~65535|ZR d|
--|UxDD|0~~6331|UxDD nndd|nn: 0~~63, dd: 0~~31
--
--**✎Note:**
--
--* In addition to the "UxDD" register, the others correspond to the PLC register one by one. UxDD corresponds to U in the PLC;
--* The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
--* All bit registers are in the form of bits in word, and the range is the same as the word register;
--
--**3）Communication Settings**
--
--[[image:image-20220831171127-1.png]]
--
--**4）Cable Wiring**
--
--[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
--
--= Create communication with **Modbus ** =
--
--== **MODBUS RTU Slave (All function)** ==
--
  Select the protocol "Modbus RTU Slave (All Fuction)",
  Then set baud rate, port, stop bits, data bits, parity.
@@ -1650,7 +1650,7 @@
  (% style="text-align:center" %)
  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
--== **MODBUS RTU Master** ==
++== **V-BOX as Master** ==
  Select the protocol "Modbus RTU Master",
@@ -1686,61 +1686,6 @@
  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
  |0F (Write multiple bits)
--== **MODBUS TCP Slave (All function)** ==
--
--Supported series: MODBUS TCP controller
--
--V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
--
--**1）V-BOX Setting**
--
--|**Items**|**Settings**|**Note**
--|Protocol|MODBUS TCP Slave (All function)|
--|Connection|Ethernet|
--|Port No.|502|
--|PLC station No.|1
--
--**2）Address List**
--
--|**Type**|**Register**|**Function code & Description**
--|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
--|06 (write single register: write a binary value to a holding register)
--|10 (write values to multiple addresses )
--|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
--|06 (write single register: write a binary value to a holding register)
--|10 (write values to multiple addresses )
--|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
--|06 (write single register: write a binary value to a holding register)
--|10 (write values to multiple addresses )
--|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
--|10 (write values to multiple addresses )
--|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
--|05 (Force a single coil to force the on/off state of a logic coil)
--|0F (Write multiple bits, ie write continuously)
--|(% rowspan="3" %)1|02 (Read the input state)
--|05 (Force a single coil to force the on/off state of a logic coil)
--|0F (Write multiple bits)
--|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
--|05 (Force a single coil to force the on/off state of a logic coil)
--|0F (Write multiple bits)
--|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
--|0F (Write multiple bits)
--
--**3）Communication Settings**
--
--Configure V-BOX Ethernet IP in Networking Settings
--
--[[image:image-20220902111833-3.png]]
--
--
--Configure PLC Ethernet IP in Communication；
--
--[[image:image-20220902111121-1.png]]
--
--**4）Cable Wiring**
--
--[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
--
  == **communicate with VB inverter** ==
  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]

image-20220831163041-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-58.6 KB

Content

image-20220831163406-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-28.4 KB

Content

image-20220831163422-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-53.9 KB

Content

image-20220831163441-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-13.7 KB

Content

image-20220831163548-5.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-37.1 KB

Content

image-20220831163553-6.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-37.1 KB

Content

image-20220831163923-7.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.3 KB

Content

image-20220831164626-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-56.1 KB

Content

image-20220831164646-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-28.4 KB

Content

image-20220831164700-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-66.6 KB

Content

image-20220831164731-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-12.3 KB

Content

image-20220831165008-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-13.3 KB

Content

image-20220831165017-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-36.2 KB

Content

image-20220831165031-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-28.3 KB

Content

image-20220831165238-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.4 KB

Content

image-20220831170147-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.1 KB

Content

image-20220831170215-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-14.3 KB

Content

image-20220831170254-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-43.5 KB

Content

image-20220831170306-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-28.5 KB

Content

image-20220831171127-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-60.1 KB

Content

image-20220902104329-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-58.7 KB

Content

image-20220902111121-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-60.9 KB

Content

image-20220902111754-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-57.6 KB

Content

image-20220902111833-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Ben

Size

...	...	@@ -1,1 +1,0 @@
1		-56.1 KB

Content

image-20221116105850-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bob

Size

...	...	@@ -1,1 +1,0 @@
1		-18.9 KB

Content

image-20221116105947-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bob

Size

...	...	@@ -1,1 +1,0 @@
1		-18.7 KB

Content

image-20221116110802-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bob

Size

...	...	@@ -1,1 +1,0 @@
1		-16.4 KB

Content

image-20221116110832-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bob

Size

...	...	@@ -1,1 +1,0 @@
1		-42.2 KB

Content

image-20221116110907-3.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bob

Size

...	...	@@ -1,1 +1,0 @@
1		-17.8 KB

Content

image-20221116110917-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bob

Size

...	...	@@ -1,1 +1,0 @@
1		-23.2 KB

Content

Changes for page 1 Communication

Summary

Details

Navigation

Table of Contents