Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 184.1
edited by Bob
on 2022/11/25 17:08
Change comment: There is no comment for this version
To version 145.1
edited by Ben
on 2022/08/31 16:15
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Bob
1 +XWiki.Ben
Content
... ... @@ -182,7 +182,7 @@
182 182  
183 183  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
184 184  
185 -**1）V-BOX setting**
185 +**1）PLC Settings**
186 186  
187 187  |**Item**|**Settings**|**Note**
188 188  |Protocol|Allen-Bradlley DF1 Advanced|
... ... @@ -420,7 +420,7 @@
420 420  The above are all the steps for establishing Ethernet communication between Wecon V-box with CompactLogix L1769 PLC.
421 421  
422 422  
423 -= **Allen-Bradley Ethernet DF1** =
423 +== **Allen-Bradley Ethernet DF1** ==
424 424  
425 425  [[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Allen-Bradley%20Ethernet%20DF1.zip]]
426 426  
... ... @@ -436,7 +436,7 @@
436 436  
437 437  Supported Series: Siemens S7-300 series PLC
438 438  
439 -**1）V-BOX setting**
439 +**1）PLC Setting**
440 440  
441 441  |**Items**|**Settings**|**Note**
442 442  |Protocol|Simens S7-300 Ethernet|
... ... @@ -498,7 +498,7 @@
498 498  
499 499  Supported Series: Siemens S7-400, S7-1200 and S7-1500
500 500  
501 -**1）V-BOX setting**
501 +**1）PLC Setting**
502 502  
503 503  |=**Items**|=**Settings**|=**Note**
504 504  |Protocol|Siemens S7-XXX|
... ... @@ -704,101 +704,6 @@
704 704  [[image:image-20220825100845-4.png]]
705 705  
706 706  
707 -== **FX3U Ethernet Protocol** ==
708 -
709 -Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
710 -
711 -**1)V-BOX Settings**
712 -
713 -|Items|Settings|Note
714 -|Protocol|Mitsubishi FX3U|
715 -|Connection|Ethernet|
716 -|Port No.|5009|Must be the same as the PLC setting
717 -|PLC station No.|0|
718 -
719 -**2)Address List**
720 -
721 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
722 -|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
723 -|Y|Y|Y OOO|0~~377|
724 -|M|M|M DDDD|0~~7679|
725 -|SM|SM|SM DDDD|8000~~8511|
726 -|S|S|S DDDD|0~~4095|
727 -|TS|TS|TS DDD|0~~511|
728 -|CS|CS|CS DDD|0~~255|
729 -|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
730 -|TN|TN|TN DDD|0~~511|
731 -|D|D|D DDDD|0~~7999|
732 -|SD|SD|SD DDDD|8000~~8511|
733 -|R|R|R DDDDD|0~~32767|
734 -
735 -**3)Ethernet Module Settings**
736 -
737 -FX3U-ENET-L module configuration
738 -Set up the FX3U-ENET-L Ethernet module settings as follows.
739 -Select the module location, which in this document is Module 0.
740 -
741 -[[image:image-20221116105850-1.png]]
742 -
743 -Select "Operational setting" to enter the following screen.
744 -
745 -The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
746 -
747 -[[image:image-20221116105947-1.png]]
748 -
749 -Select "Open setting" to enter the setting interface, the settings are as follows.
750 -
751 -The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
752 -
753 -Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
754 -
755 -[[image:image-20221116110802-1.png]]
756 -
757 -Click on "transter setup" - "PC side I/F setting", see the following figure.
758 -
759 -After setting, the first download must use the programming cable, as shown in the figure; after that, can
760 -
761 -use the IP set in the "Ethernet board" to communicate directly with the network cable.
762 -
763 -[[image:image-20221116110832-2.png||height="423" width="708"]]
764 -
765 -Read and write data from the Ethernet module
766 -
767 -[[image:image-20221116110907-3.png]]
768 -
769 -Set "Transter setup" to COM communication, and read or write operation as shown below
770 -
771 -[[image:image-20221116110917-4.png]]
772 -
773 -**4)PLC Settings (GX Works 2)**
774 -
775 -Create a blank FX5U project
776 -
777 -Find Current Connection in the navigation
778 -
779 -[[image:image-20221116111427-1.png||height="421" width="705"]]
780 -
781 -Select Connection Channel List
782 -
783 -Select Ethernet board communication
784 -
785 -[[image:image-20221116111451-2.png||height="421" width="705"]]
786 -
787 -Select Ethernet Module
788 -Set the IP address of the PLC
789 -
790 -[[image:image-20221116111509-3.png||height="666" width="699"]]
791 -
792 -Read or write PLC data, in this document is read
793 -
794 -[[image:image-20221116111651-4.png||height="416" width="697"]]
795 -
796 -[[image:image-20221116111727-5.png||height="416" width="697"]]
797 -
798 -**4)Configure the communication protocol**
799 -
800 -[[image:image-20221119101946-2.png||height="395" width="695"]]
801 -
802 802  == **FX5U Serial Protocol** ==
803 803  
804 804  Mitsubishi FX5U series PLC
... ... @@ -953,10 +953,11 @@
953 953  
954 954  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
955 955  
956 -**5）Cable Wiring**
861 +**5）电缆布线**
957 957  
958 958  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
959 959  
865 +
960 960  == **L02 Serial Protocol** ==
961 961  
962 962  Mitsubishi L02 series CPU built-in serial port.
... ... @@ -1090,9 +1090,6 @@
1090 1090  
1091 1091  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1092 1092  
1093 -(% class="wikigeneratedid" %)
1094 -== **Q12H ** ==
1095 -
1096 1096  == **QJ71E71 Ethernet Protocol** ==
1097 1097  
1098 1098  Mitsubishi QJ71E71 Ethernet communication module;
... ... @@ -1141,13 +1141,10 @@
1141 1141  
1142 1142  * Click [Ethernet/CC IE/MELSECNET];
1143 1143  * Please select [Ethernet] as network type;
1144 -* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
1047 +* Set station I/O number according to situation (For example, 0000 means that the module is connected to PLC CPU in first order);
1145 1145  * Select [Online] as Mode;
1146 -* [[image:image-20221119171343-2.png||height="341" width="587"]]
1147 1147  * Click [Operation setting] to set IP;
1148 1148  * Select [Binary Code] as [Communication Data Code];
1149 -* [[image:image-20221119171436-3.png||height="354" width="588"]]
1150 -* Click [Open setting]
1151 1151  * Set protocol: TCP;
1152 1152  * Set [unpassive] in [Open system];
1153 1153  * Set [receive] in [Fixed buffer];
... ... @@ -1154,16 +1154,14 @@
1154 1154  * Set [procedure Exist] in [Fixed buffer communication];
1155 1155  * Disable [Pairing open];
1156 1156  * Set [No confirm] in [Existence confirmation];
1157 -* Host station port number: 5009;
1057 +* Host station port number: 1025;
1158 1158  * Save settings;
1159 -* [[image:image-20221119171611-4.png||height="354" width="588"]]
1160 1160  * Download project into PLC and restart it
1161 1161  
1162 1162  **4）Configure the communication protocol**
1163 1163  
1164 -[[image:image-20221119171832-5.png||height="354" width="625"]]
1063 +[[image:image-20220825143728-1.png]]
1165 1165  
1166 -
1167 1167  **5）Cable Wiring**
1168 1168  
1169 1169  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png"]]
... ... @@ -1296,362 +1296,66 @@
1296 1296  * Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
1297 1297  * [[image:image-20220831161356-1.png]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
1298 1298  
1299 -= Create communication with Xinje** PLC** =
1197 +== **EtherNet/IP NX series Protocol** ==
1300 1300  
1301 -== **XC serial protocol** ==
1199 +Supported series: Omron NX/NJ series
1302 1302  
1303 -**1）V-BOX Settings**
1201 +**HMI Setting**
1304 1304  
1305 -|**Item**|**Settings**|**Note**
1306 -|Protocol|XINJE XC MODBUS|
1307 -|Connection|RS232|
1308 -|Baud rate|19200|
1309 -|Data bit|8|
1310 -|Parity|EVEN|
1311 -|Stop bit|1|
1203 +|**Items**|**Settings**|**Note**
1204 +|Protocol|Omron NX Ethernet/IP|
1205 +|Connection|Ethernet|
1206 +|Port No.|44818|
1312 1312  |PLC station No.|1|
1313 1313  
1314 -**2）Address List**
1209 +**Instruction**
1315 1315  
1316 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1317 -|Bit|M|M|M d|0~~8511|
1318 -|Bit|X|X|X o|0~~1747|
1319 -|Bit|Y|Y|Y o|0~~1747|
1320 -|Bit|S|S|S d|0~~1023|
1321 -|Bit|T|T|T d|0~~4095|
1322 -|Bit|C|C|C d|0~~634|
1323 -|Word|D|D|D d|0~~8511|
1324 -|Word|TD|TD|TD d|0~~618|
1325 -|Word|CD|CD|CD d|0~~634|
1326 -|Word|FD|FD|FD d|0~~8511|
1211 +1) In Sysmac Studio, please select [Publish Only] for [Network Publish] when setting address tag.
1327 1327  
1328 -**3）Configure the communication protocol**
1213 +2) When [Do not publish] is selected for a tag, different import methods may lead to different results. When import tags by [Get Tags from Device], the tag will be eliminated. If [Import tags] is selected, the tags will be imported, but the communication will not succeed.
1329 1329  
1215 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_4156caf6f116c570.png?width=600&height=277&rev=1.1||alt="12.PLC Protocol_html_4156caf6f116c570.png" height="277" width="600"]]
1330 1330  
1331 -[[image:image-20220831163041-1.png]]
1217 +**Export labels from Sysmac Studio**
1332 1332  
1333 -**4）Cable Wiring**
1219 +Launch Sysmac Studio, under Global Variables create the address labels, and thenselect [Tools] -> [Export Global Variables];
1334 1334  
1335 -Figure
1221 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_26f91dee66c723e9.png?width=600&height=276&rev=1.1||alt="12.PLC Protocol_html_26f91dee66c723e9.png" height="276" width="600"]]
1336 1336  
1337 -[[image:image-20220831163406-2.png]][[image:image-20220831163422-3.png]]
1223 +Launch PIStudio, in [Communication] Settings add Omron NX Ethernet/IP protocol;
1338 1338  
1339 -Pin Definition Diagram
1225 +Click [Label manage];
1340 1340  
1341 -[[image:image-20220831163441-4.png]]
1227 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cd38d2d0c5187f6b.png?width=600&height=276&rev=1.1||alt="12.PLC Protocol_html_cd38d2d0c5187f6b.png" height="276" width="600"]]
1342 1342  
1343 -== **XD serial protocol** ==
1229 +Click [Import labels] and then select the file exported in step 1;
1344 1344  
1345 -**1）V-BOX Settings**
1231 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_52bd5da678bef9b4.png?width=600&height=403&rev=1.1||alt="12.PLC Protocol_html_52bd5da678bef9b4.png" height="403" width="600"]]
1346 1346  
1347 -Supported Series: Delta Xinjie XD/XE Series PLC
1233 +The Import Status field shows the result, click [OK] to finish importing address labels;
1348 1348  
1349 -|**Item**|**Settings**|**Note**
1350 -|Protocol|XINJE XD/XC MODBUS|
1351 -|Connection|RS232|
1352 -|Baud rate|19200|
1353 -|Data bit|8|
1354 -|Parity|EVEN|
1355 -|Stop bit|1|
1356 -|PLC station No.|1|
1235 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_7f0465a589b98912.png?width=600&height=291&rev=1.1||alt="12.PLC Protocol_html_7f0465a589b98912.png" height="291" width="600"]]
1357 1357  
1358 -**2）Address List**
1237 +**Communication Settings**
1359 1359  
1360 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1361 -|Bit|M|M|M d|0~~74999|
1362 -|Bit|X1xx|X1xx|X1xx o|0~~1177|
1363 -|Bit|X2xx|X2xx|X2xx o|0~~277|
1364 -|Bit|X|X|X o|0~~77|
1365 -|Bit|Y1xx|Y1xx|Y1xx o|0~~1177|
1366 -|Bit|Y2xx|Y2xx|Y2xx o|0~~277|
1367 -|Bit|Y|Y|Y o|0~~4095|
1368 -|Bit|SM|SM|SM d|0~~4999|(((
1369 -
1370 -)))
1371 -|Bit|T|T|T d|0~~4999|
1372 -|Bit|C|C|C d|0~~4999|
1373 -|Bit|ET|ET|ET d|0~~31|
1374 -|Bit|SE|SE|SE d|0~~31|
1375 -|Bit|HM|HM|HM d|0~~11999|
1376 -|Bit|HSC|HSC|HSC d|0~~39|
1377 -|Bit|HS|HS|HS d|0~~999|
1378 -|Bit|HT|HT|HT d|0~~1999|
1379 -|Bit|HC|HC|HC d|0~~1999|
1380 -|Bit|S|S|S d|0~~7999|
1381 -|Word|D|D|D d|0~~69999|
1382 -|Word|ID|ID|ID d|0~~99|
1383 -|Word|ID1xx|ID1xx|ID1xx d|0~~999|
1384 -|Word|ID2xx|ID2xx|ID2xx d|0~~299|
1385 -|Word|QD|QD|QD d|0~~99|
1386 -|Word|QD1xx|QD1xx|QD1xx d|0~~999|
1387 -|Word|QD2xx|QD2xx|QD2xx d|0~~299|
1388 -|Word|SD|SD|SD d|0~~4999|
1389 -|Word|TD|TD|TD d|0~~575|
1390 -|Word|CD|CD|CD d|0~~575|
1391 -|Word|ETD|ETD|ETD d|0~~31|
1392 -|Word|HD|HD|HD d|0~~24999|
1393 -|Word|HSD|HSD|HSD d|0~~1023|
1394 -|Word|HTD|HTD|HTD d|0~~95|
1395 -|Word|HCD|HCD|HCD d|0~~95|
1396 -|Word|HSCD|HSCD|HSCD d|0~~31|
1397 -|Word|FD|FD|FD d|0~~8191|
1398 -|Word|SFD|SFD|SFD d|0~~5999|
1399 -|Word|FS|FS|FS d|0~~47|
1239 +Enable HMI Ethernet in [Project Settings];
1400 1400  
1401 -**3）Configure the communication protocol**
1241 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_43b671f18153910d.png?width=405&height=107&rev=1.1||alt="12.PLC Protocol_html_43b671f18153910d.png" height="107" width="405"]]
1402 1402  
1403 -[[image:image-20220831163923-7.png]]
1243 +Set PLC IP in [Device IP] settings;
1404 1404  
1245 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_437cb087b36b5784.png?width=600&height=330&rev=1.1||alt="12.PLC Protocol_html_437cb087b36b5784.png" height="330" width="600"]]
1405 1405  
1247 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_60ef71528a99abf5.png?width=554&height=188&rev=1.1||alt="12.PLC Protocol_html_60ef71528a99abf5.png" height="188" width="554"]]
1406 1406  
1407 -**4）Cable Wiring**
1249 +**Cable Wiring**
1408 1408  
1409 -Figure
1251 +[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1410 1410  
1411 -[[image:image-20220831163406-2.png]][[image:image-20220831163553-6.png]]
1253 += Create communication with **Modbus RTU** =
1412 1412  
1413 -Pin Definition Diagram
1255 +== **V-BOX as Slave** ==
1414 1414  
1415 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
1416 -
1417 -
1418 -= Create communication with **Schneider PLC** =
1419 -
1420 -== **Schneider MODBUS RTU** ==
1421 -
1422 -**1）V-BOX Setting**
1423 -
1424 -|=**Parameters**|=**Recommended**|=**Notes**
1425 -|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
1426 -|**Connection**|RS485|
1427 -|**Baud rate**|19200|
1428 -|**Data bit**|8|
1429 -|**Parity**|Even|
1430 -|**Stop bit**|1|
1431 -|**PLC station No.**|1|
1432 -
1433 -**2）Address List**
1434 -
1435 -|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
1436 -|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
1437 -|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
1438 -|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
1439 -|W|MW|DDDDDD|0 ~~ 999999|Output register
1440 -|DW|MD|DDDDDD|0 ~~ 999999|Output register
1441 -
1442 -**3）Configure the communication protocol**
1443 -
1444 -[[image:image-20220902104329-1.png]]
1445 -
1446 -**4）Cable Wiring**
1447 -
1448 -**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
1449 -
1450 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
1451 -
1452 -= Create communication with Inovance** PLC** =
1453 -
1454 -== **H3U serial protocol** ==
1455 -
1456 -**1）V-BOX Settings**
1457 -
1458 -|**Item**|**Settings**|**Note**
1459 -|Protocol|INOVANCE H3U PLC|
1460 -|Connection|RS422|
1461 -|Baud rate|9600|
1462 -|Data bit|7|
1463 -|Parity|EVEN|
1464 -|Stop bit|1|
1465 -|PLC station No.|0|
1466 -
1467 -**2）Address List**
1468 -
1469 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1470 -|Bit|X|X|X o|0~~303237|
1471 -|Bit|Y|Y|Y o|0~~303237|
1472 -|Bit|M|M|M d|0~~99999|
1473 -|Bit|T|T|T d|0~~99999|
1474 -|Bit|C|C|C d|0~~99999|
1475 -|Bit|SM|SM|SM d|8000~~999|
1476 -|Bit|S|T|S d|0~~99999|
1477 -|Bit|Lamp|Lamp|Lamp d|0~~0|
1478 -|Word|X|X|X o|0~~303237|
1479 -|Word|Y|Y|Y o|0~~303237|
1480 -|Word|M|M|M d|0~~99999|
1481 -|Word|T|T|T d|0~~99999|
1482 -|Word|C|C|C d|0~~199|
1483 -|Word|D|D|D d|0~~7999|
1484 -|Word|S|S|S d|0~~99999|
1485 -|Word|SD|SD|SD d|8000~~9999|
1486 -|Word|R|R|R d|0~~32767|
1487 -
1488 -**3）Configure the communication protocol**
1489 -
1490 -[[image:image-20220831164626-1.png]]
1491 -
1492 -
1493 -
1494 -**4）Cable Wiring**
1495 -
1496 -Figure
1497 -
1498 -[[image:image-20220831164646-2.png]][[image:image-20220831164700-3.png]]
1499 -
1500 -Pin Definition Diagram
1501 -
1502 -[[image:image-20220831164731-4.png]]
1503 -
1504 -= Create communication with Panasonic** PLC** =
1505 -
1506 -== **FP serial protocol** ==
1507 -
1508 -**1）V-BOX Settings**
1509 -
1510 -|**Item**|**Settings**|**Note**
1511 -|Protocol|Panasonic FP MFWTOCOL|
1512 -|Connection|RS232|
1513 -|Baud rate|9600|
1514 -|Data bit|8|
1515 -|Parity|ODD|
1516 -|Stop bit|1|
1517 -|PLC station No.|1|
1518 -
1519 -**2）Address List**
1520 -
1521 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1522 -|Bit|X|X|X d|0~~9999|
1523 -|Bit|Y|Y|Y d|0~~9999|
1524 -|Bit|R|R|R d|0~~9999|
1525 -|Bit|T|T|T d|0~~9999|
1526 -|Bit|C|C|C d|0~~9999|
1527 -|Bit|L|L|L d|0~~9999|
1528 -|Word|WX|WX|WX d|0~~9999|
1529 -|Word|WY|WY|WY d|0~~9999|
1530 -|Word|WR|WR|WR d|0~~9999|
1531 -|Word|WL|WL|WL d|0~~9999|
1532 -|Word|LD|LD|LD d|0~~9999|
1533 -|Word|DT|DT|DT d|0~~65535|
1534 -|Word|FL|FL|FL d|0~~9999|
1535 -|Word|EV|EV|EV d|0~~9999|
1536 -|Word|SV|SV|SV d|0~~9999|
1537 -
1538 -**3）Configure the communication protocol**
1539 -
1540 -[[image:image-20220831165238-4.png]]
1541 -
1542 -
1543 -
1544 -**4）Cable Wiring**
1545 -
1546 -Figure
1547 -
1548 -[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
1549 -
1550 -Pin Definition Diagram
1551 -
1552 -[[image:image-20220831165008-1.png]]
1553 -
1554 -= Create communication with LS** PLC** =
1555 -
1556 -== **XBC serial protocol** ==
1557 -
1558 -**1）V-BOX Settings**
1559 -
1560 -|**Item**|**Settings**|**Note**
1561 -|Protocol|LS XBC CNet|
1562 -|Connection|RS232|
1563 -|Baud rate|115200|
1564 -|Data bit|8|
1565 -|Parity|NONE|
1566 -|Stop bit|1|
1567 -|PLC station No.|1|
1568 -
1569 -**2）Address List**
1570 -
1571 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1572 -|Bit|P|P|P d|0~~2047|
1573 -|Bit|M|M|M d|0~~2047|
1574 -|Bit|L|L|L d|0~~11263|
1575 -|Bit|K|K|K d|0~~16183|
1576 -|Bit|F|F|F d|0~~2047|
1577 -|Bit|D|D|D d|0~~32767|
1578 -|Bit|R|R|R d|0~~32767|
1579 -|Bit|U|U|U d|0~~4095|
1580 -|Word|P|P|P d|0~~2047|
1581 -|Word|M|M|M d|0~~2047|
1582 -|Word|L|L|L d|0~~11263|
1583 -|Word|K|K|K d|0~~16183|
1584 -|Word|F|F|F d|0~~2047|
1585 -|Word|C|C|C d|0~~2047|
1586 -|Word|T|T|T d|0~~2047|
1587 -|Word|D|D|D d|0~~32767|
1588 -|Word|N|N|N d|0~~21503|
1589 -|Word|R|R|R d|0~~32767|
1590 -|Word|U|U|U d|0~~4095|
1591 -|Word|Z|Z|Z d|0~~127|
1592 -|Word|S|S|S d|0~~127|
1593 -
1594 -**3）Configure the communication protocol**
1595 -
1596 -[[image:image-20220831170147-1.png]]
1597 -
1598 -**4）Cable Wiring**
1599 -
1600 -Figure
1601 -
1602 -[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
1603 -
1604 -Pin Definition Diagram
1605 -
1606 -[[image:image-20220831170215-2.png]]
1607 -
1608 -== **XGK FEnet Ethernet protocol** ==
1609 -
1610 -Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
1611 -
1612 -**1）V-BOX Settings**
1613 -
1614 -|**Items**|**Settings**|**Note**
1615 -|Protocol|LG XGK FEnet(Ethernet)|
1616 -|Connection|Ethernet|
1617 -|Port No.|2004|
1618 -
1619 -**2）Address List**
1620 -
1621 -|**Type**|**Register**|**Range**|**Format**|**Note**
1622 -|(% rowspan="14" %)Word|P|0~~2047|P d|
1623 -|M|0~~2047|M d|
1624 -|K|0~~2047|K d|
1625 -|F|0~~2047|F d|
1626 -|T|0~~2047|T d|
1627 -|C|0~~2047|C d|
1628 -|Z|0~~127|Z d|
1629 -|S|0~~127|S d|
1630 -|L|0~~11263|L d|
1631 -|N|0~~21503|N d|
1632 -|D|0~~32767|D d|
1633 -|R|0~~32767|R d|
1634 -|ZR|0~~65535|ZR d|
1635 -|UxDD|0~~6331|UxDD nndd|nn: 0~~63, dd: 0~~31
1636 -
1637 -**✎Note:**
1638 -
1639 -* In addition to the "UxDD" register, the others correspond to the PLC register one by one. UxDD corresponds to U in the PLC;
1640 -* The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
1641 -* All bit registers are in the form of bits in word, and the range is the same as the word register;
1642 -
1643 -**3）Communication Settings**
1644 -
1645 -[[image:image-20220831171127-1.png]]
1646 -
1647 -**4）Cable Wiring**
1648 -
1649 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1650 -
1651 -= Create communication with **Modbus ** =
1652 -
1653 -== **MODBUS RTU Slave (All function)** ==
1654 -
1655 1655  Select the protocol "Modbus RTU Slave (All Fuction)",
1656 1656  
1657 1657  Then set baud rate, port, stop bits, data bits, parity.
... ... @@ -1659,7 +1659,7 @@
1659 1659  (% style="text-align:center" %)
1660 1660  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
1661 1661  
1662 -== **MODBUS RTU Master** ==
1264 +== **V-BOX as Master** ==
1663 1663  
1664 1664  Select the protocol "Modbus RTU Master",
1665 1665  
... ... @@ -1695,61 +1695,6 @@
1695 1695  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
1696 1696  |0F (Write multiple bits)
1697 1697  
1698 -== **MODBUS TCP Slave (All function)** ==
1699 -
1700 -Supported series: MODBUS TCP controller
1701 -
1702 -V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
1703 -
1704 -**1）V-BOX Setting**
1705 -
1706 -|**Items**|**Settings**|**Note**
1707 -|Protocol|MODBUS TCP Slave (All function)|
1708 -|Connection|Ethernet|
1709 -|Port No.|502|
1710 -|PLC station No.|1
1711 -
1712 -**2）Address List**
1713 -
1714 -|**Type**|**Register**|**Function code & Description**
1715 -|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
1716 -|06 (write single register: write a binary value to a holding register)
1717 -|10 (write values to multiple addresses )
1718 -|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
1719 -|06 (write single register: write a binary value to a holding register)
1720 -|10 (write values to multiple addresses )
1721 -|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
1722 -|06 (write single register: write a binary value to a holding register)
1723 -|10 (write values to multiple addresses )
1724 -|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
1725 -|10 (write values to multiple addresses )
1726 -|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
1727 -|05 (Force a single coil to force the on/off state of a logic coil)
1728 -|0F (Write multiple bits, ie write continuously)
1729 -|(% rowspan="3" %)1|02 (Read the input state)
1730 -|05 (Force a single coil to force the on/off state of a logic coil)
1731 -|0F (Write multiple bits)
1732 -|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
1733 -|05 (Force a single coil to force the on/off state of a logic coil)
1734 -|0F (Write multiple bits)
1735 -|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
1736 -|0F (Write multiple bits)
1737 -
1738 -**3）Communication Settings**
1739 -
1740 -Configure V-BOX Ethernet IP in Networking Settings
1741 -
1742 -[[image:image-20220902111833-3.png]]
1743 -
1744 -
1745 -Configure PLC Ethernet IP in Communication；
1746 -
1747 -[[image:image-20220902111121-1.png]]
1748 -
1749 -**4）Cable Wiring**
1750 -
1751 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1752 -
1753 1753  == **communicate with VB inverter** ==
1754 1754  
1755 1755  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]
image-20220831163041-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.6 KB
Content
image-20220831163406-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.4 KB
Content
image-20220831163422-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -53.9 KB
Content
image-20220831163441-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.7 KB
Content
image-20220831163548-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20220831163553-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20220831163923-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.3 KB
Content
image-20220831164626-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -56.1 KB
Content
image-20220831164646-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.4 KB
Content
image-20220831164700-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -66.6 KB
Content
image-20220831164731-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -12.3 KB
Content
image-20220831165008-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
image-20220831165017-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -36.2 KB
Content
image-20220831165031-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.3 KB
Content
image-20220831165238-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.4 KB
Content
image-20220831170147-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.1 KB
Content
image-20220831170215-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -14.3 KB
Content
image-20220831170254-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -43.5 KB
Content
image-20220831170306-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.5 KB
Content
image-20220831171127-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.1 KB
Content
image-20220902104329-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.7 KB
Content
image-20220902111121-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.9 KB
Content
image-20220902111754-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.6 KB
Content
image-20220902111833-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -56.1 KB
Content
image-20221116105850-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.9 KB
Content
image-20221116105947-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.7 KB
Content
image-20221116110802-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -16.4 KB
Content
image-20221116110832-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -42.2 KB
Content
image-20221116110907-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -17.8 KB
Content
image-20221116110917-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -23.2 KB
Content
image-20221116111427-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -63.4 KB
Content
image-20221116111451-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -225.5 KB
Content
image-20221116111509-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -34.1 KB
Content
image-20221116111651-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -74.3 KB
Content
image-20221116111727-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -106.2 KB
Content
image-20221116114106-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -99.5 KB
Content
image-20221119101759-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -62.1 KB
Content
image-20221119101946-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -68.7 KB
Content
image-20221119171318-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -90.3 KB
Content
image-20221119171343-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -90.3 KB
Content
image-20221119171436-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -43.4 KB
Content
image-20221119171611-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -23.1 KB
Content
image-20221119171832-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -69.6 KB
Content