Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 230.1
edited by Theodore Xu
on 2023/04/23 15:41
Change comment: There is no comment for this version
To version 144.1
edited by Ben
on 2022/08/31 16:14
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.AiXia
1 +XWiki.Ben
Content
... ... @@ -176,116 +176,16 @@
176 176  
177 177  The above are all the steps for establishing ethernet communication between V-BOX with LX5V PLC.
178 178  
179 -= Create communication with Allen-Bradley(**Rockwell**)** PLC** =
179 += Create communication with **Rockwell PLC** =
180 180  
181 -== **DF1 Advanced Protocol** ==
181 +== (% id="cke_bm_5621S" style="display:none" %)** **(%%)**MicroLogix Protocol** ==
182 182  
183 -MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05; PLC-5
184 -
185 -**1) V-Box Settings**
186 -
187 -|=Item|=Recommended |=Note
188 -|=Protocol|Allen Bradley DF1 Advanced|
189 -|=Connection|RS232|
190 -|=Baud rate|19200|
191 -|=Stop bits|1|
192 -|=Data bits|8|
193 -|=Parity|None|
194 -|=PLC Station No.|1|
195 -|=HMI Station No.|0|
196 -
197 -**2) Address List**
198 -
199 -|=**Type**|=**Device registers**|=**Format**|=**Range**|=Note
200 -|(% colspan="1" rowspan="7" %)Bit|I1|I1ddd.dd|0.0~~255.15|Only able to communicate with file number I1
201 -|O0|O0ddd.dd|0.0~~255.15|Only able to communicate with file number O0
202 -|S2|S2ddd.dd|0.0~~255.15|Only able to communicate with file number S2
203 -|B3|B3ddd.dd|0.0~~255.15|Only able to communicate with file number B3
204 -|BN|BNddddd.dd|0.0~~99255.15|(((
205 -Bit data file B0~~B99
206 -
207 -First two digits is for file number
208 -
209 -For example, BN13001.00 represents file number B13, address 001, the 0th bit.
210 -)))
211 -|N7|N7ddd.dd|0.0~~255.15|Only able to communicate with file number N7
212 -|NN|NNddddd.dd|0.0~~99255.15|(((
213 -Integer data file bit format N0~~N99
214 -
215 -First two digits is for file number
216 -
217 -For example, NN13001.00 represents file number N13, address 001, the 0th bit.
218 -)))
219 -|(% rowspan="11" %)Word|S2|S2ddd|0~~255|Only able to communicate with file number S2
220 -|T4S|T4Sddd|0~~255|Only able to communicate with file number T4 (Timer Preset Value)
221 -|T4P|T4Pddd|0~~255|Only able to communicate with file number T4 (Timer Accumulator Value)
222 -|TNS|TNSddddd|0~~99255|(((
223 -Timer Preset Value
224 -
225 -First two digits is for file number
226 -
227 -For example, TNS99255 represents file number T99, address 255.
228 -)))
229 -|TNP|TNPddddd|0~~99255|(((
230 -Timer Accumulator Value
231 -
232 -First two digits is for file number
233 -
234 -For example, TNP99255 represents file number T99, address 255.
235 -)))
236 -|C5S|C5Sddd|0~~255|Only able to communicate with file number C5 (Counter Preset Value)
237 -|C5P|C5Pddd|0~~255|Only able to communicate with file number C5 (Counter Accumulator Value)
238 -|CNS|CNSddddd|0~~99255|(((
239 -Counter Preset Value
240 -
241 -First two digits is for file number
242 -
243 -For example, CNS99255 represents file number C99, address 255.
244 -)))
245 -|CNP|CNPddddd|0~~99255|(((
246 -Counter Accumulator Value
247 -
248 -First two digits is for file number
249 -
250 -For example, CNP99255 represents file number C99, address 255.
251 -)))
252 -|N7|N7ddd|0~~255|Only able to communicate with file number N7
253 -|NN|NNddd|0~~99255|(((
254 -Integer data file
255 -
256 -First two digits is for file number
257 -
258 -For example, NN99255 represents file number N99, address 255.
259 -)))
260 -|(% colspan="1" rowspan="3" %)Double Word|F8|F8ddd|0~~255|(((
261 -Only able to communicate with file number N7
262 -)))
263 -|FN|FNddddd|0~~99255|(((
264 -Floating point data file
265 -
266 -First two digits is for file number
267 -
268 -For example, FN99255 represents file number F99, address 255.
269 -)))
270 -|LN|LNddddd|0~~99255|Long
271 -
272 -**3) Cable Wiring**
273 -
274 -(% style="text-align:center" %)
275 -[[image:ABRS232.gif]]
276 -
277 -(% class="wikigeneratedid" id="HMicroLogixA0Protocol" %)
278 -(% id="cke_bm_5621S" style="display:none" %)** **
279 -
280 -== **MicroLogix Protocol** ==
281 -
282 -(% class="wikigeneratedid" %)
283 283  MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
284 284  
285 -**1）V-BOX setting**
185 +**1）PLC Settings**
286 286  
287 287  |**Item**|**Settings**|**Note**
288 -|Protocol|Allen-Bradley DF1 Advanced|
188 +|Protocol|Allen-Bradlley DF1 Advanced|
289 289  |Connection|RS232|
290 290  |Baud rate|19200|
291 291  |Data bit|8|
... ... @@ -520,145 +520,11 @@
520 520  The above are all the steps for establishing Ethernet communication between Wecon V-box with CompactLogix L1769 PLC.
521 521  
522 522  
523 -This example introduces the establishment of Ethernet communication between Wecon V-box and 2080-LC50-48QWB,Micro850. It is introduced through three parts: PLC software configuration, V-box software configuration.
423 +== **Allen-Bradley Ethernet DF1** ==
524 524  
525 -(% class="wikigeneratedid" id="HSoftwareconfigurationofPLC" %)
526 -(((
527 -**Software configuration of PLC**
528 -)))
529 -
530 -(% class="wikigeneratedid" id="HPLCprogrammingsoftware" %)
531 -(((
532 -**1）PLC programming software：Connected Components Workbench™**
533 -
534 -(% style="text-align:center" %)
535 -[[image:software.png]]
536 -
537 -**2）New PLC project**
538 -
539 -Click New Project and select the PLC model.
540 -
541 -(% style="text-align:center" %)
542 -[[image:project create.png]]
543 -
544 -**3）Set Ethernet parameters**
545 -
546 -Follow the steps below to configure Ethernet parameters
547 -
548 -PLC IP address：192.168.39.56
549 -
550 -default gateway：192.168.39.1
551 -
552 -subnet mask：255.255.255.0
553 -
554 -(% style="text-align:center" %)
555 -[[image:Ethernet.png]]
556 -
557 -**4）connect PLC**
558 -
559 -**When downloading the setting, need to change the status of the PLC to PRG**
560 -
561 -(% style="text-align:center" %)
562 -[[image:conne ab plc.png]]
563 -
564 -**V-box software configuration**
565 -
566 -**1）V-box programming software**
567 -
568 -(% style="text-align:center" %)
569 -[[image:v-net client vers.png]]
570 -
571 -**2）Set communication port parameters**
572 -
573 -In the device list on the left, find the Vbox that communicates with the L1769, click it and select configuration,communication port configuration in the main interface to add a communication protocol.
574 -
575 -(% style="text-align:center" %)
576 -[[image:V-NET_Client_t2Rg2wpSoY.png]]
577 -
578 -The communication port is selected as Ethernet, the device type is selected as Allen-Bradley, the protocol is Allen-BradleyMicro850_FreeTag EthemetIP, and the IP is the internal IP address of the L1769 PLC. The port number is 44818.
579 -
580 -(% style="text-align:center" %)
581 -[[image:V-NET_Client_communication.png]]
582 -
583 -Export variables from PLC, select CSV file, comma delimited. After adding the protocol Allen-BradleyMicro850_FreeTag, click[[image:https://docs.we-con.com.cn/bin/download/V-BOX/V-Net/Training/1%20Communication/WebHome/image-20220714143838-2.png?rev=1.1||alt="image-20220714143838-2.png"]]icon add label.
584 -
585 -(% style="text-align:center" %)
586 -[[image:export1.png]]
587 -
588 -(% style="text-align:center" %)
589 -[[image:CCW.Shell_E5Cwj4tUL3.png]]
590 -
591 -(% style="text-align:center" %)
592 -[[image:V-NET_Client_iKKKhcgxm1.png]]
593 -
594 -**3）Engineering production**
595 -
596 -According to your own needs, use the V-NET client software to edit the required data monitoring points.
597 -
598 -(% style="text-align:center" %)
599 -[[image:V-NET_Client_KOR0AHEA4M.png]]
600 -
601 -
602 -)))
603 -
604 -== **Ethernet DF1 Protocol** ==
605 -
606 606  [[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Allen-Bradley%20Ethernet%20DF1.zip]]
607 607  
608 -= Create communication with **Crouzet PLC** =
609 609  
610 -== **CROUZET M3 (FBD)** ==
611 -
612 -Support Series: Crouzet Millenium 3 CD12/CB12
613 -
614 -**1）V-BOX setting**
615 -
616 -|=Item|=Recommended |=Note
617 -|=Protocol|CROUZET M3 (FBD)|
618 -|=Connection|RS232|
619 -|=Baud rate|115200|
620 -|=Stop bits|1|
621 -|=Data bits|7|
622 -|=Parity|EVEN|
623 -
624 -**2）Address List**
625 -
626 -|=**Type**|=**Device registers**|=**Format**|=**Range**|=Note
627 -|(% rowspan="4" %)Bit|I|I DD|1~~99|Input
628 -|SLIBit|SLIBit DD.dd|1.0~~24.15|Serial Link Input
629 -|SLOBit|SLOBit DD.dd|25.0~~48.15|Serial Link Output(Read only)
630 -|State|State D|1~~1|PLC state(Read only)
631 -|(% rowspan="5" %)Word|AI|AI DD|1~~99|Analog Input
632 -|SLIn|SLIn DD|1~~24|Serial Link Input
633 -|SLOut|SLOut DD|25~~48|Serial Link Output(Read only)
634 -|Time|Time D|1~~6|(((
635 -Time1: Second
636 -
637 -Time2: Minute
638 -
639 -Time3: Hour
640 -
641 -Time4: Day
642 -
643 -Time5: Month
644 -
645 -Time6: Year
646 -)))
647 -|Order|Order D|1~~1|(((
648 -Running command(Write only)
649 -
650 -~=2: Run mode; =1: Stop mode;
651 -)))
652 -
653 -**3）Cable Wiring**
654 -
655 -(% style="text-align:center" %)
656 -[[image:CrouzetRS232 VBox.png]]
657 -
658 -{{info}}
659 -**✎Note: **As the wiring diagram indicated, this protocol requires the DB9 serial port pin 4. But pin 4 is undefined for all V-Box, so it need the user to solder a Pull-up resistor to make the pin 4 working. As for how to solder the resistor on the motherboard, please contact with Wecon technical support for the details.
660 -{{/info}}
661 -
662 662  = Create communication with **Siemens PLC** =
663 663  
664 664  == **S7-200 Smart Ethernet Protocol** ==
... ... @@ -670,7 +670,7 @@
670 670  
671 671  Supported Series: Siemens S7-300 series PLC
672 672  
673 -**1）V-BOX setting**
439 +**1）PLC Setting**
674 674  
675 675  |**Items**|**Settings**|**Note**
676 676  |Protocol|Simens S7-300 Ethernet|
... ... @@ -732,7 +732,7 @@
732 732  
733 733  Supported Series: Siemens S7-400, S7-1200 and S7-1500
734 734  
735 -**1）V-BOX setting**
501 +**1）PLC Setting**
736 736  
737 737  |=**Items**|=**Settings**|=**Note**
738 738  |Protocol|Siemens S7-XXX|
... ... @@ -842,97 +842,6 @@
842 842  
843 843  [[image:image-20220824162342-2.png]]
844 844  
845 -== **LOGO Ethernet Protocol** ==
846 -
847 -Supported Series: Siemens Logo 0BA0, 0BA1 series
848 -
849 -**V-BOX Settings**
850 -
851 -
852 -|**Items**|**Settings**|**Note**
853 -|Protocol|Siemens LOGO|
854 -|Connection|Ethernet|
855 -|Port No.|102|
856 -|PLC station No.|2|
857 -
858 -**Address List**
859 -
860 -
861 -|**Number**|**Address Type**|**Data Type**|**Range**|**DB Address**|**PLC Address**
862 -|1|RTC|Word|1-7|DB1.DBX984.0|0x001ec0
863 -|2|VB|Byte|0-1469|DB1.DBX0.0|0x000000
864 -|3|VD|Double Word|0-1466|DB1.DBX0.0|0x000000
865 -|4|VW|Word|0-1468|DB1.DBX0.0|0x000000
866 -|5|NAQ|Word|1-32|DB1.DBX1406.0|0x002bf0
867 -|6|NAI|Word|1-64|DB1.DBX1262.0|0x002770
868 -|7|AM|Word|1-64|DB1.DBX1118.0|0x0022f0
869 -|8|AQ|Word|1-16|DB1.DBX1072.0|0x002180
870 -|9|AI|Word|1-16|DB1.DBX1032.0|0x002040
871 -|10|I|Bit|1-64|DB1.DBX1024.0|0x002000
872 -|11|Q|Bit|1-64|DB1.DBX1064.0|0x002140
873 -|12|M|Bit|1-112|DB1.DBX1104.0|0x002280
874 -|13|NI|Bit|1-128|DB1.DBX1246.0|0x0026f0
875 -|14|NQ|Bit|1-128|DB1.DBX1390.0|0x002b70
876 -|15|V|Bit|0-14697|DB1.DBX0.0|0x000000
877 -
878 -**PLC Settings in LOGO Software:**
879 -
880 -Click [Tools]~-~-[Ethernet Connections],shown as below.
881 -
882 -(% style="text-align:center" %)
883 -[[image:PIStudio.12\.PLC protocols.WebHome@12.PLC Protocol_html_8b9d2322edf89519.png]]
884 -
885 -Set Ethernet connection parameter. IP, Subnet Mask, shown as below.
886 -
887 -(% style="text-align:center" %)
888 -[[image:PIStudio.12\.PLC protocols.WebHome@image-20221228142937-4.png]]
889 -
890 -**TSAP set**:The value set by local TSAP is the remote TSAP set in HMI. PLC's remote TSAP is the opposite,shown as below.
891 -
892 -(% style="text-align:center" %)
893 -[[image:PIStudio.12\.PLC protocols.WebHome@image-20221228143047-5.png]]
894 -
895 - **Download Project**: Click "Address book" to add the IP address to be downloaded (fi."Detect" to check whether the IP address can be detected. Then click “ok”, and the system will prompt that PLC will be "STOP" mode. Click “YES” to start download.
896 -
897 -(% style="text-align:center" %)
898 -[[image:PIStudio.12\.PLC protocols.WebHome@image-20221228143246-6.png]]
899 -
900 -**V-BOX Communication Settings**
901 -
902 -Set PLC IP in [IP Address] settings;
903 -
904 -(% style="text-align:center" %)
905 -[[image:LldwDGntf4.png]]
906 -
907 -Enable V-BOX Ethernet in [Network];
908 -
909 -(% style="text-align:center" %)
910 -[[image:WgvjfWbQif.png]]
911 -
912 -TSAP setting
913 -
914 -* The initialization script needs to set the source TSAP address and the target TSAP address, otherwise the communication will not be successful.
915 -
916 -{{code language="LUA"}}
917 -function init.main()
918 -addr_setword("@W_0#HSW1200",8192) -- Set the source TSAP address
919 -addr_setword("@W_0#HSW1201",4096) -- Set the destination TSAP address
920 -end
921 -{{/code}}
922 -
923 -Note: The name of the test script is init, 8192 and 4096 are the data used for the test, there is no HSW address in the register option, but you can directly set the value of the corresponding address through the code.
924 -
925 -**✎Note:**
926 -
927 -* **Communication port configuration: **
928 -** Continuous length needs to be set to 0.
929 -** Integration interval needs to be set to 1. (no change may result in data errors)
930 -** Set Port and Device Station NO.
931 -** Other set as defaulted.
932 -* **Notes on the use of registers:**
933 -** Register VD: Use only registers that are multiples of 4, such as 0, 4, 8, etc.
934 -** Register VW: Use only registers thay are multiples of 2, such as 0, 2, 4 etc. (Using an odd-length register may result in data errors, such as 2 3 4 )
935 -
936 936  = Create communication with **Mitsubishi PLC** =
937 937  
938 938  == **FX1S，1N，2N Serial Protocol** ==
... ... @@ -1029,101 +1029,6 @@
1029 1029  [[image:image-20220825100845-4.png]]
1030 1030  
1031 1031  
1032 -== **FX3U Ethernet Protocol** ==
1033 -
1034 -Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
1035 -
1036 -**1)V-BOX Settings**
1037 -
1038 -|Items|Settings|Note
1039 -|Protocol|Mitsubishi FX3U|
1040 -|Connection|Ethernet|
1041 -|Port No.|5009|Must be the same as the PLC setting
1042 -|PLC station No.|0|
1043 -
1044 -**2)Address List**
1045 -
1046 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1047 -|(% colspan="1" rowspan="7" %)Bit|X|X|X OOO|0~~377|
1048 -|Y|Y|Y OOO|0~~377|
1049 -|M|M|M DDDD|0~~7679|
1050 -|SM|SM|SM DDDD|8000~~8511|
1051 -|S|S|S DDDD|0~~4095|
1052 -|TS|TS|TS DDD|0~~511|
1053 -|CS|CS|CS DDD|0~~255|
1054 -|(% colspan="1" rowspan="9" %)Word|CN|CN|CN DDD|0~~199|
1055 -|TN|TN|TN DDD|0~~511|
1056 -|D|D|D DDDD|0~~7999|
1057 -|SD|SD|SD DDDD|8000~~8511|
1058 -|R|R|R DDDDD|0~~32767|
1059 -
1060 -**3)Ethernet Module Settings**
1061 -
1062 -FX3U-ENET-L module configuration
1063 -Set up the FX3U-ENET-L Ethernet module settings as follows.
1064 -Select the module location, which in this document is Module 0.
1065 -
1066 -[[image:image-20221116105850-1.png]]
1067 -
1068 -Select "Operational setting" to enter the following screen.
1069 -
1070 -The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
1071 -
1072 -[[image:image-20221116105947-1.png]]
1073 -
1074 -Select "Open setting" to enter the setting interface, the settings are as follows.
1075 -
1076 -The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
1077 -
1078 -Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
1079 -
1080 -[[image:image-20221116110802-1.png]]
1081 -
1082 -Click on "transter setup" - "PC side I/F setting", see the following figure.
1083 -
1084 -After setting, the first download must use the programming cable, as shown in the figure; after that, can
1085 -
1086 -use the IP set in the "Ethernet board" to communicate directly with the network cable.
1087 -
1088 -[[image:image-20221116110832-2.png||height="423" width="708"]]
1089 -
1090 -Read and write data from the Ethernet module
1091 -
1092 -[[image:image-20221116110907-3.png]]
1093 -
1094 -Set "Transter setup" to COM communication, and read or write operation as shown below
1095 -
1096 -[[image:image-20221116110917-4.png]]
1097 -
1098 -**4)PLC Settings (GX Works 2)**
1099 -
1100 -Create a blank FX5U project
1101 -
1102 -Find Current Connection in the navigation
1103 -
1104 -[[image:image-20221116111427-1.png||height="421" width="705"]]
1105 -
1106 -Select Connection Channel List
1107 -
1108 -Select Ethernet board communication
1109 -
1110 -[[image:image-20221116111451-2.png||height="421" width="705"]]
1111 -
1112 -Select Ethernet Module
1113 -Set the IP address of the PLC
1114 -
1115 -[[image:image-20221116111509-3.png||height="666" width="699"]]
1116 -
1117 -Read or write PLC data, in this document is read
1118 -
1119 -[[image:image-20221116111651-4.png||height="416" width="697"]]
1120 -
1121 -[[image:image-20221116111727-5.png||height="416" width="697"]]
1122 -
1123 -**4)Configure the communication protocol**
1124 -
1125 -[[image:image-20221119101946-2.png||height="395" width="695"]]
1126 -
1127 1127  == **FX5U Serial Protocol** ==
1128 1128  
1129 1129  Mitsubishi FX5U series PLC
... ... @@ -1278,10 +1278,11 @@
1278 1278  
1279 1279  [[image:image-20220825112403-1.png||alt="图片-20220825112403-1.png"]]
1280 1280  
1281 -**5）Cable Wiring**
861 +**5）电缆布线**
1282 1282  
1283 1283  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1284 1284  
865 +
1285 1285  == **L02 Serial Protocol** ==
1286 1286  
1287 1287  Mitsubishi L02 series CPU built-in serial port.
... ... @@ -1415,12 +1415,6 @@
1415 1415  
1416 1416  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
1417 1417  
1418 -== **Q12H Serial Protocol** ==
1419 -
1420 -This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
1421 -
1422 -[[**Download link**>>https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
1423 -
1424 1424  == **QJ71E71 Ethernet Protocol** ==
1425 1425  
1426 1426  Mitsubishi QJ71E71 Ethernet communication module;
... ... @@ -1469,13 +1469,10 @@
1469 1469  
1470 1470  * Click [Ethernet/CC IE/MELSECNET];
1471 1471  * Please select [Ethernet] as network type;
1472 -* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
1047 +* Set station I/O number according to situation (For example, 0000 means that the module is connected to PLC CPU in first order);
1473 1473  * Select [Online] as Mode;
1474 -* [[image:image-20221119171343-2.png||height="341" width="587"]]
1475 1475  * Click [Operation setting] to set IP;
1476 1476  * Select [Binary Code] as [Communication Data Code];
1477 -* [[image:image-20221119171436-3.png||height="354" width="588"]]
1478 -* Click [Open setting]
1479 1479  * Set protocol: TCP;
1480 1480  * Set [unpassive] in [Open system];
1481 1481  * Set [receive] in [Fixed buffer];
... ... @@ -1482,16 +1482,14 @@
1482 1482  * Set [procedure Exist] in [Fixed buffer communication];
1483 1483  * Disable [Pairing open];
1484 1484  * Set [No confirm] in [Existence confirmation];
1485 -* Host station port number: 5009;
1057 +* Host station port number: 1025;
1486 1486  * Save settings;
1487 -* [[image:image-20221119171611-4.png||height="354" width="588"]]
1488 1488  * Download project into PLC and restart it
1489 1489  
1490 1490  **4）Configure the communication protocol**
1491 1491  
1492 -[[image:image-20221119171832-5.png||height="354" width="625"]]
1063 +[[image:image-20220825143728-1.png]]
1493 1493  
1494 -
1495 1495  **5）Cable Wiring**
1496 1496  
1497 1497  [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png"]]
... ... @@ -1500,105 +1500,12 @@
1500 1500  
1501 1501  == **DVP Ethernet Protocol** ==
1502 1502  
1503 -Supoort Series: DELTA DVP20/32/40/60ES200RE/200TE or any DVP models with built-in Ethernet port, DELTA DVPEN01-SL module
1073 +[[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
1504 1504  
1505 -**1）V-BOX Settings**
1506 -
1507 -|=**Items**|=**Settings**|=**Note**
1508 -|Protocol|DELTA DVP MODBUS TCP|
1509 -|Connection|Ethernet|
1510 -|Port No.|502|
1511 -|Device No.|1|
1512 -|VBox Device No.|0|
1513 -
1514 -**2）Address List **
1515 -
1516 -|=**Type**|=(% style="width: 191px;" %)**Device registers**|=(% style="width: 217px;" %)**VBox registers**|=(% style="width: 168px;" %)**Format**|=(% style="width: 225px;" %)**Range**|=**Note**
1517 -|Bit|(% style="width:191px" %)X|(% style="width:217px" %)X|(% style="width:168px" %)X OOO|(% style="width:225px" %)0~~377|
1518 -|Bit|(% style="width:191px" %)Y|(% style="width:217px" %)Y|(% style="width:168px" %)Y OOO|(% style="width:225px" %)0~~377|
1519 -|Bit|(% style="width:191px" %)M0|(% style="width:217px" %)M0|(% style="width:168px" %)M0DDDD|(% style="width:225px" %)0~~1535|
1520 -|Bit|(% style="width:191px" %)M1|(% style="width:217px" %)M1|(% style="width:168px" %)M1DDDD|(% style="width:225px" %)1536~~4096|
1521 -|Bit|(% style="width:191px" %)T|(% style="width:217px" %)T|(% style="width:168px" %)TDDD|(% style="width:225px" %)0~~255|
1522 -|Bit|(% style="width:191px" %)C|(% style="width:217px" %)C|(% style="width:168px" %)CDDD|(% style="width:225px" %)0~~255|
1523 -|Bit|(% style="width:191px" %)S|(% style="width:217px" %)S|(% style="width:168px" %)SDDDD|(% style="width:225px" %)0~~1023|
1524 -|Word|(% style="width:191px" %)D0|(% style="width:217px" %)D0|(% style="width:168px" %)D0DDDD|(% style="width:225px" %)0~~4095|
1525 -|Word|(% style="width:191px" %)D1|(% style="width:217px" %)D1|(% style="width:168px" %)D1DDDD|(% style="width:225px" %)4096~~11999|
1526 -|Word|(% style="width:191px" %)T|(% style="width:217px" %)T|(% style="width:168px" %)TDDD|(% style="width:225px" %)0~~255|
1527 -|Word|(% style="width:191px" %)C|(% style="width:217px" %)C|(% style="width:168px" %)CDDD|(% style="width:225px" %)0~~199|
1528 -|Double Word|(% style="width:191px" %)HC|(% style="width:217px" %)HC|(% style="width:168px" %)HCDDD|(% style="width:225px" %)200~~255|
1529 -
1530 -**3) PLC Setting:**
1531 -
1532 -~1. Create new project in Delta WPL Soft, and click Setting to open the communication settings:
1533 -
1534 -(% style="text-align:center" %)
1535 -[[image:DVPEthernetWPLSoft2.png]]
1536 -
1537 -2. Set up the communication type and PLC IP:
1538 -
1539 -(% style="text-align:center" %)
1540 -[[image:DVPEthernetSetup.png]]
1541 -
1542 -(% class="wikigeneratedid" %)
1543 -3. Click OK and save the settings. Then click Communication on toolbar, then click Transfer Setup to open new window:
1544 -
1545 -(% style="text-align:center" %)
1546 -[[image:DVPEthernetTransfer.png]]
1547 -
1548 -(% class="wikigeneratedid" %)
1549 -4. Select Communication Mode as PC => PLC to download or select PC <=PLC to upload:
1550 -
1551 -(% style="text-align:center" %)
1552 -[[image:DVPEthernetPLCtoPC.png]]
1553 -
1554 -5. Click Auto-Search Ethernet Module to find the PLC on the same LAN network:
1555 -
1556 -(% style="text-align:center" %)
1557 -[[image:DVPEthernetAutoSearch.png]]
1558 -
1559 -**4) V-BOX Setting:**
1560 -
1561 -Set the same IP address according to the setting from WPL Soft:
1562 -
1563 -(% style="text-align:center" %)
1564 -[[image:DVPEthernetVNETPortocol.png]]
1565 -
1566 1566  == **DVP serial protocol** ==
1567 1567  
1568 -Supoort Series: DELTA DVP EH/ES/SS/EX/EH2/SV/SA/SC/SX
1077 +[[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
1569 1569  
1570 -**1）V-BOX Settings**
1571 -
1572 -|=**Items**|=**Settings**|=**Note**
1573 -|Protocol|DELTA DVP PROTOCOL|
1574 -|Connection|RS232|
1575 -|Baud Rate|9600|
1576 -|Stop Bit|1|
1577 -|Data Bit|7|
1578 -|Parity|EVEN|
1579 -|Device No.|1|
1580 -
1581 -(% class="wikigeneratedid" %)
1582 -**2）Address List**
1583 -
1584 -|=**Type**|=(% style="width: 191px;" %)**Device registers**|=(% style="width: 217px;" %)**VBox registers**|=(% style="width: 168px;" %)**Format**|=(% style="width: 225px;" %)**Range**|=**Note**
1585 -|Bit|(% style="width:191px" %)X|(% style="width:217px" %)X|(% style="width:168px" %)X OOOOOO|(% style="width:225px" %)0~~303237|
1586 -|Bit|(% style="width:191px" %)Y|(% style="width:217px" %)Y|(% style="width:168px" %)Y OOOOOO|(% style="width:225px" %)0~~303237|
1587 -|Bit|(% style="width:191px" %)M|(% style="width:217px" %)M|(% style="width:168px" %)MDDDDD|(% style="width:225px" %)0~~99999|
1588 -|Bit|(% style="width:191px" %)T|(% style="width:217px" %)T|(% style="width:168px" %)TDDDDD|(% style="width:225px" %)0~~99999|
1589 -|Bit|(% style="width:191px" %)C|(% style="width:217px" %)C|(% style="width:168px" %)CDDDDD|(% style="width:225px" %)0~~99999|
1590 -|Bit|(% style="width:191px" %)S|(% style="width:217px" %)S|(% style="width:168px" %)SDDDDD|(% style="width:225px" %)0~~99999|
1591 -|Word|(% style="width:191px" %)D|(% style="width:217px" %)D|(% style="width:168px" %)D DDDDD|(% style="width:225px" %)0~~99999|
1592 -|Word|(% style="width:191px" %)T|(% style="width:217px" %)T|(% style="width:168px" %)TDDDDD|(% style="width:225px" %)0~~99999|
1593 -|Word|(% style="width:191px" %)C|(% style="width:217px" %)C|(% style="width:168px" %)CDDD|(% style="width:225px" %)0~~199|
1594 -|Double Word|(% style="width:191px" %)C|(% style="width:217px" %)C|(% style="width:168px" %)CDDDDD|(% style="width:225px" %)200~~99999|
1595 -
1596 -(% class="wikigeneratedid" %)
1597 -**3）Wiring Diagram**
1598 -
1599 -(% style="text-align:center" %)
1600 -[[image:Delta DVP PROTOCOLSerial232.png]]
1601 -
1602 1602  == **AS Ethernet Protocol** ==
1603 1603  
1604 1604  **1）V-BOX Settings**
... ... @@ -1632,6 +1632,7 @@
1632 1632  
1633 1633  **3）Configure the communication protocol**
1634 1634  
1112 +
1635 1635  [[image:image-20220831160010-4.png]]
1636 1636  
1637 1637  **4）Cable Wiring**
... ... @@ -1716,361 +1716,10 @@
1716 1716  * Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
1717 1717  * [[image:image-20220831161356-1.png]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
1718 1718  
1719 -= Create communication with Xinje** PLC** =
1197 += Create communication with **Modbus RTU** =
1720 1720  
1721 -== **XC serial protocol** ==
1199 +== **V-BOX as Slave** ==
1722 1722  
1723 -**1）V-BOX Settings**
1724 -
1725 -|**Item**|**Settings**|**Note**
1726 -|Protocol|XINJE XC MODBUS|
1727 -|Connection|RS232|
1728 -|Baud rate|19200|
1729 -|Data bit|8|
1730 -|Parity|EVEN|
1731 -|Stop bit|1|
1732 -|PLC station No.|1|
1733 -
1734 -**2）Address List**
1735 -
1736 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1737 -|Bit|M|M|M d|0~~8511|
1738 -|Bit|X|X|X o|0~~1747|
1739 -|Bit|Y|Y|Y o|0~~1747|
1740 -|Bit|S|S|S d|0~~1023|
1741 -|Bit|T|T|T d|0~~4095|
1742 -|Bit|C|C|C d|0~~634|
1743 -|Word|D|D|D d|0~~8511|
1744 -|Word|TD|TD|TD d|0~~618|
1745 -|Word|CD|CD|CD d|0~~634|
1746 -|Word|FD|FD|FD d|0~~8511|
1747 -
1748 -**3）Configure the communication protocol**
1749 -
1750 -
1751 -[[image:image-20220831163041-1.png]]
1752 -
1753 -**4）Cable Wiring**
1754 -
1755 -Figure
1756 -
1757 -[[image:image-20220831163406-2.png]][[image:image-20220831163422-3.png]]
1758 -
1759 -Pin Definition Diagram
1760 -
1761 -[[image:image-20220831163441-4.png]]
1762 -
1763 -== **XD serial protocol** ==
1764 -
1765 -**1）V-BOX Settings**
1766 -
1767 -Supported Series: Xinjie XD/XE Series PLC
1768 -
1769 -|**Item**|**Settings**|**Note**
1770 -|Protocol|XINJE XD/XC MODBUS|
1771 -|Connection|RS232|
1772 -|Baud rate|19200|
1773 -|Data bit|8|
1774 -|Parity|EVEN|
1775 -|Stop bit|1|
1776 -|PLC station No.|1|
1777 -
1778 -**2）Address List**
1779 -
1780 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1781 -|Bit|M|M|M d|0~~74999|
1782 -|Bit|X1xx|X1xx|X1xx o|0~~1177|
1783 -|Bit|X2xx|X2xx|X2xx o|0~~277|
1784 -|Bit|X|X|X o|0~~77|
1785 -|Bit|Y1xx|Y1xx|Y1xx o|0~~1177|
1786 -|Bit|Y2xx|Y2xx|Y2xx o|0~~277|
1787 -|Bit|Y|Y|Y o|0~~4095|
1788 -|Bit|SM|SM|SM d|0~~4999|(((
1789 -
1790 -)))
1791 -|Bit|T|T|T d|0~~4999|
1792 -|Bit|C|C|C d|0~~4999|
1793 -|Bit|ET|ET|ET d|0~~31|
1794 -|Bit|SE|SE|SE d|0~~31|
1795 -|Bit|HM|HM|HM d|0~~11999|
1796 -|Bit|HSC|HSC|HSC d|0~~39|
1797 -|Bit|HS|HS|HS d|0~~999|
1798 -|Bit|HT|HT|HT d|0~~1999|
1799 -|Bit|HC|HC|HC d|0~~1999|
1800 -|Bit|S|S|S d|0~~7999|
1801 -|Word|D|D|D d|0~~69999|
1802 -|Word|ID|ID|ID d|0~~99|
1803 -|Word|ID1xx|ID1xx|ID1xx d|0~~999|
1804 -|Word|ID2xx|ID2xx|ID2xx d|0~~299|
1805 -|Word|QD|QD|QD d|0~~99|
1806 -|Word|QD1xx|QD1xx|QD1xx d|0~~999|
1807 -|Word|QD2xx|QD2xx|QD2xx d|0~~299|
1808 -|Word|SD|SD|SD d|0~~4999|
1809 -|Word|TD|TD|TD d|0~~575|
1810 -|Word|CD|CD|CD d|0~~575|
1811 -|Word|ETD|ETD|ETD d|0~~31|
1812 -|Word|HD|HD|HD d|0~~24999|
1813 -|Word|HSD|HSD|HSD d|0~~1023|
1814 -|Word|HTD|HTD|HTD d|0~~95|
1815 -|Word|HCD|HCD|HCD d|0~~95|
1816 -|Word|HSCD|HSCD|HSCD d|0~~31|
1817 -|Word|FD|FD|FD d|0~~8191|
1818 -|Word|SFD|SFD|SFD d|0~~5999|
1819 -|Word|FS|FS|FS d|0~~47|
1820 -
1821 -**3）Configure the communication protocol**
1822 -
1823 -[[image:image-20220831163923-7.png]]
1824 -
1825 -
1826 -
1827 -**4）Cable Wiring**
1828 -
1829 -Figure
1830 -
1831 -[[image:image-20220831163406-2.png]][[image:image-20220831163553-6.png]]
1832 -
1833 -Pin Definition Diagram
1834 -
1835 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220830160232-3.png?rev=1.1||alt="image-20220830160232-3.png"]]
1836 -
1837 -= Create communication with **Schneider PLC** =
1838 -
1839 -== **Schneider MODBUS RTU** ==
1840 -
1841 -**1）V-BOX Setting**
1842 -
1843 -|=**Parameters**|=**Recommended**|=**Notes**
1844 -|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
1845 -|**Connection**|RS485|
1846 -|**Baud rate**|19200|
1847 -|**Data bit**|8|
1848 -|**Parity**|Even|
1849 -|**Stop bit**|1|
1850 -|**PLC station No.**|1|
1851 -
1852 -**2）Address List**
1853 -
1854 -|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
1855 -|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
1856 -|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
1857 -|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
1858 -|W|MW|DDDDDD|0 ~~ 999999|Output register
1859 -|DW|MD|DDDDDD|0 ~~ 999999|Output register
1860 -
1861 -**3）Configure the communication protocol**
1862 -
1863 -[[image:image-20220902104329-1.png]]
1864 -
1865 -**4）Cable Wiring**
1866 -
1867 -**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
1868 -
1869 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/image-20220817154212-1.jpeg?width=554&height=315&rev=1.1||alt="image-20220817154212-1.jpeg" height="315" width="554"]]
1870 -
1871 -= Create communication with Inovance** PLC** =
1872 -
1873 -== **H3U serial protocol** ==
1874 -
1875 -**1）V-BOX Settings**
1876 -
1877 -|**Item**|**Settings**|**Note**
1878 -|Protocol|INOVANCE H3U PLC|
1879 -|Connection|RS422|
1880 -|Baud rate|9600|
1881 -|Data bit|7|
1882 -|Parity|EVEN|
1883 -|Stop bit|1|
1884 -|PLC station No.|0|
1885 -
1886 -**2）Address List**
1887 -
1888 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1889 -|Bit|X|X|X o|0~~303237|
1890 -|Bit|Y|Y|Y o|0~~303237|
1891 -|Bit|M|M|M d|0~~99999|
1892 -|Bit|T|T|T d|0~~99999|
1893 -|Bit|C|C|C d|0~~99999|
1894 -|Bit|SM|SM|SM d|8000~~999|
1895 -|Bit|S|T|S d|0~~99999|
1896 -|Bit|Lamp|Lamp|Lamp d|0~~0|
1897 -|Word|X|X|X o|0~~303237|
1898 -|Word|Y|Y|Y o|0~~303237|
1899 -|Word|M|M|M d|0~~99999|
1900 -|Word|T|T|T d|0~~99999|
1901 -|Word|C|C|C d|0~~199|
1902 -|Word|D|D|D d|0~~7999|
1903 -|Word|S|S|S d|0~~99999|
1904 -|Word|SD|SD|SD d|8000~~9999|
1905 -|Word|R|R|R d|0~~32767|
1906 -
1907 -**3）Configure the communication protocol**
1908 -
1909 -[[image:image-20220831164626-1.png]]
1910 -
1911 -
1912 -
1913 -**4）Cable Wiring**
1914 -
1915 -Figure
1916 -
1917 -[[image:image-20220831164646-2.png]][[image:image-20220831164700-3.png]]
1918 -
1919 -Pin Definition Diagram
1920 -
1921 -[[image:image-20220831164731-4.png]]
1922 -
1923 -= Create communication with Panasonic** PLC** =
1924 -
1925 -== **FP serial protocol** ==
1926 -
1927 -**1）V-BOX Settings**
1928 -
1929 -|**Item**|**Settings**|**Note**
1930 -|Protocol|Panasonic FP MFWTOCOL|
1931 -|Connection|RS232|
1932 -|Baud rate|9600|
1933 -|Data bit|8|
1934 -|Parity|ODD|
1935 -|Stop bit|1|
1936 -|PLC station No.|1|
1937 -
1938 -**2）Address List**
1939 -
1940 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1941 -|Bit|X|X|X d|0~~9999|
1942 -|Bit|Y|Y|Y d|0~~9999|
1943 -|Bit|R|R|R d|0~~9999|
1944 -|Bit|T|T|T d|0~~9999|
1945 -|Bit|C|C|C d|0~~9999|
1946 -|Bit|L|L|L d|0~~9999|
1947 -|Word|WX|WX|WX d|0~~9999|
1948 -|Word|WY|WY|WY d|0~~9999|
1949 -|Word|WR|WR|WR d|0~~9999|
1950 -|Word|WL|WL|WL d|0~~9999|
1951 -|Word|LD|LD|LD d|0~~9999|
1952 -|Word|DT|DT|DT d|0~~65535|
1953 -|Word|FL|FL|FL d|0~~9999|
1954 -|Word|EV|EV|EV d|0~~9999|
1955 -|Word|SV|SV|SV d|0~~9999|
1956 -
1957 -**3）Configure the communication protocol**
1958 -
1959 -[[image:image-20220831165238-4.png]]
1960 -
1961 -
1962 -
1963 -**4）Cable Wiring**
1964 -
1965 -Figure
1966 -
1967 -[[image:image-20220831165031-3.png]][[image:image-20220831165017-2.png]]
1968 -
1969 -Pin Definition Diagram
1970 -
1971 -[[image:image-20220831165008-1.png]]
1972 -
1973 -= Create communication with LS** PLC** =
1974 -
1975 -== **XBC serial protocol** ==
1976 -
1977 -**1）V-BOX Settings**
1978 -
1979 -|**Item**|**Settings**|**Note**
1980 -|Protocol|LS XBC CNet|
1981 -|Connection|RS232|
1982 -|Baud rate|115200|
1983 -|Data bit|8|
1984 -|Parity|NONE|
1985 -|Stop bit|1|
1986 -|PLC station No.|1|
1987 -
1988 -**2）Address List**
1989 -
1990 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
1991 -|Bit|P|P|P d|0~~2047|
1992 -|Bit|M|M|M d|0~~2047|
1993 -|Bit|L|L|L d|0~~11263|
1994 -|Bit|K|K|K d|0~~16183|
1995 -|Bit|F|F|F d|0~~2047|
1996 -|Bit|D|D|D d|0~~32767|
1997 -|Bit|R|R|R d|0~~32767|
1998 -|Bit|U|U|U d|0~~4095|
1999 -|Word|P|P|P d|0~~2047|
2000 -|Word|M|M|M d|0~~2047|
2001 -|Word|L|L|L d|0~~11263|
2002 -|Word|K|K|K d|0~~16183|
2003 -|Word|F|F|F d|0~~2047|
2004 -|Word|C|C|C d|0~~2047|
2005 -|Word|T|T|T d|0~~2047|
2006 -|Word|D|D|D d|0~~32767|
2007 -|Word|N|N|N d|0~~21503|
2008 -|Word|R|R|R d|0~~32767|
2009 -|Word|U|U|U d|0~~4095|
2010 -|Word|Z|Z|Z d|0~~127|
2011 -|Word|S|S|S d|0~~127|
2012 -
2013 -**3）Configure the communication protocol**
2014 -
2015 -[[image:image-20220831170147-1.png]]
2016 -
2017 -**4）Cable Wiring**
2018 -
2019 -Figure
2020 -
2021 -[[image:image-20220831170306-4.png]][[image:image-20220831170254-3.png]]
2022 -
2023 -Pin Definition Diagram
2024 -
2025 -[[image:image-20220831170215-2.png]]
2026 -
2027 -== **XGK FEnet Ethernet protocol** ==
2028 -
2029 -Supported Series: LS XGT series XGK CPU with XGL-EFMT Ethernet module
2030 -
2031 -**1）V-BOX Settings**
2032 -
2033 -|**Items**|**Settings**|**Note**
2034 -|Protocol|LG XGK FEnet(Ethernet)|
2035 -|Connection|Ethernet|
2036 -|Port No.|2004|
2037 -
2038 -**2）Address List**
2039 -
2040 -|**Type**|**Register**|**Range**|**Format**|**Note**
2041 -|(% rowspan="14" %)Word|P|0~~2047|P d|
2042 -|M|0~~2047|M d|
2043 -|K|0~~2047|K d|
2044 -|F|0~~2047|F d|
2045 -|T|0~~2047|T d|
2046 -|C|0~~2047|C d|
2047 -|Z|0~~127|Z d|
2048 -|S|0~~127|S d|
2049 -|L|0~~11263|L d|
2050 -|N|0~~21503|N d|
2051 -|D|0~~32767|D d|
2052 -|R|0~~32767|R d|
2053 -|ZR|0~~65535|ZR d|
2054 -|UxDD|0~~6331|UxDD nndd|nn: 0~~63, dd: 0~~31
2055 -
2056 -**✎Note:**
2057 -
2058 -* In addition to the "UxDD" register, the others correspond to the PLC register one by one. UxDD corresponds to U in the PLC;
2059 -* The [UxDD] register, defined in the PLC is Ux.dd, x represents the block, and dd represents 0-31 of each block. There are 64 blocks in the PLC;
2060 -* All bit registers are in the form of bits in word, and the range is the same as the word register;
2061 -
2062 -**3）Communication Settings**
2063 -
2064 -[[image:image-20220831171127-1.png]]
2065 -
2066 -**4）Cable Wiring**
2067 -
2068 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2069 -
2070 -= Create communication with **Modbus ** =
2071 -
2072 -== **MODBUS RTU Slave (All function)** ==
2073 -
2074 2074  Select the protocol "Modbus RTU Slave (All Fuction)",
2075 2075  
2076 2076  Then set baud rate, port, stop bits, data bits, parity.
... ... @@ -2078,88 +2078,8 @@
2078 2078  (% style="text-align:center" %)
2079 2079  [[image:1624342015914-382.png||height="486" width="800" class="img-thumbnail"]]
2080 2080  
2081 -== **Communicate with Modbus Meter** ==
1208 +== **V-BOX as Master** ==
2082 2082  
2083 -The following example is using the Linfee meter LNF96EY to demonstrate how to set up the Modbus communication.
2084 -
2085 -~1. Wiring the RS485 cable first. Because the pin 58 is A, the pin 59 is B for meter. Here we use the COM1 to connect. So the diagram like follows:
2086 -
2087 -(% style="text-align:center" %)
2088 -[[image:LinfeeTerminalDiagram.png]]
2089 -
2090 -2. Check the specific Modbus parameter in the communication menu from LED display.
2091 -
2092 -So from the following pictures, we can know the Meter Address is 85, Baud rate is 9600, CRC None.
2093 -
2094 -{{info}}
2095 -**✎Note: **Meter address usually corresponding to the Modbus Slave Station No. on the Modbus communication.
2096 -{{/info}}
2097 -
2098 -(% style="text-align:center" %)
2099 -[[image:MeterModbusAllView.png]]
2100 -
2101 -(% class="wikigeneratedid" %)
2102 -3. Set up the communication in the Configuration tab.
2103 -
2104 -(% class="wikigeneratedid" %)
2105 -Select the protocol as **ModBus RTU Slave (All Function)**. And set the communication parameters like below.
2106 -
2107 -(% style="text-align:center" %)
2108 -[[image:VNETCommunicationtabmeter.png]]
2109 -
2110 -(% class="wikigeneratedid" %)
2111 -4. Create new real-time monitoring tag accroding to Modbus manual
2112 -
2113 -(% class="wikigeneratedid" %)
2114 -Enter the address we want to read from the meter. The following table is intercept part of the manual for Linfee Modbus manual.
2115 -
2116 -(% class="wikigeneratedid" %)
2117 -**0x03/0x04 command data register address**:
2118 -
2119 -(% style="width:1142.22px" %)
2120 -|(% style="display:none" %) |=(% colspan="2" rowspan="1" style="width: 165px;" %)Address(% style="display:none" %) |=Description|=Data Format|=(% style="width: 254px;" %)Data Length(Word)|=(% style="width: 282px;" %)Remark
2121 -|(%%)(% style="display:none" %) (%%) HEX|(% style="width:107px" %)DEC|(%%)(% style="display:none" %) (%%) |(% style="width:100px" %) |(%%)(% style="display:none" %) (%%) |(% style="width:318px" %)
2122 -|(% style="width:107px" %)0x00|(% style="width:100px" %)0|Reserved| | |(% style="width:318px" %)
2123 -|(% style="width:107px" %)0x02|(% style="width:100px" %)2|Reserved| | |(% style="width:318px" %)
2124 -|(% style="width:107px" %)0x04|(% style="width:100px" %)4|Reserved| | |(% style="width:318px" %)
2125 -|(% style="width:107px" %)0x06|(% style="width:100px" %)6|Ua|float|2|(% style="width:318px" %)Phase Voltage data, Unit V
2126 -|(% style="width:107px" %)0x08|(% style="width:100px" %)8|Ub|float|2|(% style="width:318px" %)Phase Voltage data, Unit V
2127 -|(% style="width:107px" %)0x0A|(% style="width:100px" %)10|Uc|float|2|(% style="width:318px" %)Phase Voltage data, Unit V
2128 -|(% style="width:107px" %)0x0C|(% style="width:100px" %)12|Uab|float|2|(% style="width:318px" %)Line Voltage data, Unit V
2129 -|(% style="width:107px" %)0x0E|(% style="width:100px" %)14|Ubc|float|2|(% style="width:318px" %)Line Voltage data, Unit V
2130 -|(% style="width:107px" %)0x10|(% style="width:100px" %)16|Uca|float|2|(% style="width:318px" %)Line Voltage data, Unit V
2131 -|(% style="width:107px" %)0x12|(% style="width:100px" %)18|Ia|float|2|(% style="width:318px" %)Phase Current data, Unit A
2132 -|(% style="width:107px" %)0x14|(% style="width:100px" %)20|Ib|float|2|(% style="width:318px" %)Phase Current data, Unit A
2133 -|(% style="width:107px" %)0x16|(% style="width:100px" %)22|Ic|float|2|(% style="width:318px" %)Phase Current data, Unit A
2134 -
2135 -{{info}}
2136 -**✎Note: **We usually use the Data Type 4 for read the Modbus registers(Function Code 03)
2137 -{{/info}}
2138 -
2139 -For example, here we want to read the Phase Voltage Ua (Modbus offset 0006), the Modbus register main No. requires input decimal number, and check whether the actual address has one address offset, so the tag configured like the following screenshot:
2140 -
2141 -(% style="text-align:center" %)
2142 -[[image:VNETModbusTagSettings.png]]
2143 -
2144 -(% style="text-align:center" %)
2145 -[[image:VNETModbusTagByteSettings.png]]
2146 -
2147 -{{info}}
2148 -**✎Note: **If the read value is incorrect, please check whether need to change the Byte order.
2149 -{{/info}}
2150 -
2151 -Set the Modbus Slave Station No.
2152 -
2153 -(% style="text-align:center" %)
2154 -[[image:ModbusStationSettings.png]]
2155 -
2156 -If the communication is setup successfully, the tag will show green light.
2157 -
2158 -(% style="text-align:center" %)
2159 -[[image:Monitoringtaggreenlight.png]]
2160 -
2161 -== **MODBUS RTU Master** ==
2162 -
2163 2163  Select the protocol "Modbus RTU Master",
2164 2164  
2165 2165  Then set baud rate, port, stop bits, data bits, parity
... ... @@ -2170,8 +2170,8 @@
2170 2170  **address list**
2171 2171  
2172 2172  (% class="table-bordered" %)
2173 -|=(% scope="row" %)**Type**|=**Data Type**|=**Function code and description**
2174 -|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (Read Input Registers: Read the current binary value in one or more input registers)
1220 +|**type**|**register**|**Function code and description**
1221 +|(% rowspan="11" %)词|(% rowspan="3" %)3|04 (Read Input Registers: Read the current binary value in one or more input registers)
2175 2175  |06 (write single register: write a binary value to a holding register)
2176 2176  |10 (write values to multiple addresses )
2177 2177  |(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
... ... @@ -2194,61 +2194,6 @@
2194 2194  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
2195 2195  |0F (Write multiple bits)
2196 2196  
2197 -== **MODBUS TCP Slave (All function)** ==
2198 -
2199 -Supported series: MODBUS TCP controller
2200 -
2201 -V-B0X works as MODBUS TCP MASTER connecting with TCP SLAVE
2202 -
2203 -**1）V-BOX Setting**
2204 -
2205 -|**Items**|**Settings**|**Note**
2206 -|Protocol|MODBUS TCP Slave (All function)|
2207 -|Connection|Ethernet|
2208 -|Port No.|502|
2209 -|PLC station No.|1
2210 -
2211 -**2）Address List**
2212 -
2213 -|=**Type**|=**Data Type**|=**Function code & Description**
2214 -|(% rowspan="11" %)Word|(% rowspan="3" %)3|04 (read input register: read current binary value in one or more input registers)
2215 -|06 (write single register: write a binary value to a holding register)
2216 -|10 (write values to multiple addresses )
2217 -|(% rowspan="3" %)4|03 (read holding register: read current binary value in one or more holding registers)
2218 -|06 (write single register: write a binary value to a holding register)
2219 -|10 (write values to multiple addresses )
2220 -|(% rowspan="3" %)W6|03 (read holding register: read current binary value in one or more holding registers)
2221 -|06 (write single register: write a binary value to a holding register)
2222 -|10 (write values to multiple addresses )
2223 -|(% rowspan="2" %)W16|03 (read holding register: read current binary value in one or more holding registers)
2224 -|10 (write values to multiple addresses )
2225 -|(% rowspan="11" %)Bit|(% rowspan="3" %)0|01 (Read coil state)
2226 -|05 (Force a single coil to force the on/off state of a logic coil)
2227 -|0F (Write multiple bits, ie write continuously)
2228 -|(% rowspan="3" %)1|02 (Read the input state)
2229 -|05 (Force a single coil to force the on/off state of a logic coil)
2230 -|0F (Write multiple bits)
2231 -|(% rowspan="3" %)W5|01 (Read coil state to obtain the current state of a set of logic coils)
2232 -|05 (Force a single coil to force the on/off state of a logic coil)
2233 -|0F (Write multiple bits)
2234 -|(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
2235 -|0F (Write multiple bits)
2236 -
2237 -**3）Communication Settings**
2238 -
2239 -Configure V-BOX Ethernet IP in Networking Settings
2240 -
2241 -[[image:image-20220902111833-3.png]]
2242 -
2243 -
2244 -Configure PLC Ethernet IP in Communication；
2245 -
2246 -[[image:image-20220902111121-1.png]]
2247 -
2248 -**4）Cable Wiring**
2249 -
2250 -[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1||alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2251 -
2252 2252  == **communicate with VB inverter** ==
2253 2253  
2254 2254  [[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]
0Il1q9GZgk.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -24.6 KB
Content
1679563870401-671.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -39.3 KB
Content
1682233464031-639.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -15.9 KB
Content
AB.gif
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -7.3 KB
Content
ABRS232.gif
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -7.3 KB
Content
CCW.Shell_E5Cwj4tUL3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -27.1 KB
Content
CrouzetRS232 VBox.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -14.9 KB
Content
DVPEthernetAutoSearch.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -43.6 KB
Content
DVPEthernetPLCtoPC.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -8.9 KB
Content
DVPEthernetSetup.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -19.9 KB
Content
DVPEthernetTransfer.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -59.9 KB
Content
DVPEthernetVNETPortocol.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -21.4 KB
Content
DVPEthernetWPLSoft.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -97.5 KB
Content
DVPEthernetWPLSoft2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -45.2 KB
Content
Delta DVP PROTOCOLSerial232.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -10.7 KB
Content
Ethernet.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -45.5 KB
Content
LinfeeTerminalDiagram.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -8.6 KB
Content
LldwDGntf4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -24.3 KB
Content
MeterModbusAddr.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -562.5 KB
Content
MeterModbusAllView.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -1.6 MB
Content
MeterModbusBaud.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -444.0 KB
Content
MeterModbusPara.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -532.0 KB
Content
ModbusStationSettings.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -35.8 KB
Content
Monitoringtaggreenlight.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -7.5 KB
Content
V-NET_Client setting.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -41.9 KB
Content
V-NET_Client_ADD.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -51.4 KB
Content
V-NET_Client_KOR0AHEA4M.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -14.2 KB
Content
V-NET_Client_TIiAymnjkx.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -12.8 KB
Content
V-NET_Client_communication.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -25.5 KB
Content
V-NET_Client_iKKKhcgxm1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -35.9 KB
Content
V-NET_Client_t2Rg2wpSoY.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -53.7 KB
Content
VNETCommunicationtabmeter.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -31.0 KB
Content
VNETModbusTagByteSettings.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -31.2 KB
Content
VNETModbusTagSettings.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -35.7 KB
Content
WgvjfWbQif.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -36.3 KB
Content
conne ab plc.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -43.1 KB
Content
export.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -115.2 KB
Content
export1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -115.2 KB
Content
image-20220831163041-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.6 KB
Content
image-20220831163406-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.4 KB
Content
image-20220831163422-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -53.9 KB
Content
image-20220831163441-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.7 KB
Content
image-20220831163548-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20220831163553-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20220831163923-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.3 KB
Content
image-20220831164626-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -56.1 KB
Content
image-20220831164646-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.4 KB
Content
image-20220831164700-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -66.6 KB
Content
image-20220831164731-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -12.3 KB
Content
image-20220831165008-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
image-20220831165017-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -36.2 KB
Content
image-20220831165031-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.3 KB
Content
image-20220831165238-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.4 KB
Content
image-20220831170147-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.1 KB
Content
image-20220831170215-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -14.3 KB
Content
image-20220831170254-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -43.5 KB
Content
image-20220831170306-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -28.5 KB
Content
image-20220831171127-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.1 KB
Content
image-20220902104329-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.7 KB
Content
image-20220902111121-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -60.9 KB
Content
image-20220902111754-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -57.6 KB
Content
image-20220902111833-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -56.1 KB
Content
image-20221116105850-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.9 KB
Content
image-20221116105947-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -18.7 KB
Content
image-20221116110802-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -16.4 KB
Content
image-20221116110832-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -42.2 KB
Content
image-20221116110907-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -17.8 KB
Content
image-20221116110917-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -23.2 KB
Content
image-20221116111427-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -63.4 KB
Content
image-20221116111451-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -225.5 KB
Content
image-20221116111509-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -34.1 KB
Content
image-20221116111651-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -74.3 KB
Content
image-20221116111727-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -106.2 KB
Content
image-20221116114106-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -99.5 KB
Content
image-20221119101759-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -62.1 KB
Content
image-20221119101946-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -68.7 KB
Content
image-20221119171318-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -90.3 KB
Content
image-20221119171343-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -90.3 KB
Content
image-20221119171436-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -43.4 KB
Content
image-20221119171611-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -23.1 KB
Content
image-20221119171832-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bob
Size
... ... @@ -1,1 +1,0 @@
1 -69.6 KB
Content
project create.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -65.5 KB
Content
software.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -25.8 KB
Content
v-net client vers.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -13.1 KB
Content