Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 24.1
edited by Ben
on 2022/08/20 11:45
Change comment: There is no comment for this version
To version 11.1
edited by Ben
on 2022/07/14 12:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -47,292 +47,79 @@
47 47  |(% rowspan="2" %)W15|01 (Read coil state to obtain the current state of a set of logic coils)
48 48  |0F (Write multiple bits)
49 49  
50 -= **WECON PLC** =
50 +== **WECON LX3V PLC** ==
51 51  
52 -Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
52 +Select the protocol (% class="mark" %)"WECON LX3V"
53 53  
54 -**HMI Settings**
54 +(% class="mark" %)then set BaudRate,Port,Stop Bit,Data Bit,Parity same with PLC.
55 55  
56 -|**Item**|**Settings**|**Note**
57 -|Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
58 -|Connection|RS422/RS485|
59 -|Baud rate|9600|
60 -|Data bit|7|
61 -|Parity|EVEN|
62 -|Stop bit|1|
63 -|PLC station No.|1|
56 +(% class="mark" %)WECON PLC RS422 port,default communication parameters is 9600,1,7,ZEVEN
64 64  
65 -**Address List**
66 -
67 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
68 -|(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
69 -|Y|Y|Y o|0~~303237|
70 -|M|M|M d|0~~99999|
71 -|T|T|T d|0~~99999|
72 -|C|C|C d|0~~99999|
73 -|S|S|S d|0~~99999|
74 -|(% rowspan="8" %)Word|X|X|Xo|0~~303237|
75 -|Y|Y|Y o|0~~303237|
76 -|M|M|M d|0~~99999|
77 -|T|T|T d|0~~99999|
78 -|C|C|C d|0~~199|
79 -|D|D|D d|0~~7999|
80 -|S|S|S d|0~~99999|
81 -|SD|SD|SD d|8000~~9999|
82 -
83 -**Cable Wiring**
84 -
85 -* **RS485**
86 -
87 87  (% style="text-align:center" %)
88 -[[image:12.PLC Protocol_html_5e9a81a14106da9e.png||data-xwiki-image-style-alignment="center" height="223" width="392" class="img-thumbnail"]]
89 -
90 -(% style="text-align:center" %)
91 -[[image:12.PLC Protocol_html_1897d92be6948d58.png||data-xwiki-image-style-alignment="center" height="223" width="393" class="img-thumbnail"]]
92 -
93 -* **RS422**
94 -
95 -(% style="text-align:center" %)
96 -[[image:12.PLC Protocol_html_5c7fca9a70da2ee8.png||data-xwiki-image-style-alignment="center" height="247" width="389" class="img-thumbnail"]]
97 -
98 -**✎Note:**
99 -
100 -* HMI COM3 is available in PI8000 series and COM3 is in COM2(hardware PIN 7 and PIN 8) .
101 -* If PLC <= 20 points,such as LX3V-1208/LX3V-0806 PLC,PLC RS485A and RS485B mean PLC COM2 RS485+ and RS485- .PLC COM2 can support modbus. Please refer to PLC COM2 setting manual.
102 -
103 -[[https:~~/~~/drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing>>url:https://drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing]]
104 -
105 -== HMI and Wecon LX5V serial communication ==
106 -
107 -This example introduces the establishment of serial port communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
108 -
109 -**Software configuration of PLC**
110 -
111 -**1）PLC programming software**
112 -
113 -[[image:image-20220810164710-1.png]]
114 -
115 -**2）New PLC project**
116 -
117 -Click New Project and select the PLC model.
118 -
119 -[[image:image-20220810172412-1.png]]
120 -
121 -**3）Set Serial port parameters**
122 -
123 -Follow the steps below to configure Serial port parameters
124 -
125 -Baud rate：115200
126 -
127 -Data bit：8
128 -
129 -Stop bit：1
130 -
131 -Parity：No verification
132 -
133 -[[image:image-20220810165759-3.png]]
134 -
135 -**4）Registers list**
136 -
137 -[[image:image-20220811102219-3.png]]
138 -
139 -**HMI software configuration**
140 -
141 -**1）HMI programming software**
142 -
143 - [[image:image-20220810171237-4.png]]
144 -
145 -**2）New HMI project**
146 -
147 -Click New Project and select the HMI model.
148 -
149 -[[image:image-20220810172010-5.png]]
150 -
151 -**3）Set communication port parameters**
152 -
153 -Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
154 -
155 -Baud rate：115200
156 -
157 -Data bit：8
158 -
159 -Stop bit：1
160 -
161 -Parity：No verification
162 -
163 -[[image:image-20220811104012-1.png]]
164 -
165 -**hardware connection**
166 -
167 -**1）Hardware wiring diagram**
168 -
169 -This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
170 -
171 -[[image:image-20220811103005-4.png]]
172 -
173 -[[image:image-20220811103227-7.png]]
174 -
175 -The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
176 -
177 -== HMI and Wecon LX5V-N Ethernet communication ==
178 -
179 - This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
180 -
181 -**Software configuration of PLC**
182 -
183 -**1）PLC programming software**
184 -
185 -[[image:image-20220810164710-1.png]]
186 -
187 -**2）New PLC project**
188 -
189 -Click New Project and select the PLC model.
190 -
191 -[[image:image-20220811115454-1.png]]
192 -
193 -**3）Set Ethernet port parameters**
194 -
195 -Follow the steps below to configure Ethernet parameters
196 -
197 -PLC IP address：192.168.39.200
198 -
199 -default gateway：192.168.39.1
200 -
201 -subnet mask：255.255.255.0
202 -
203 -[[image:image-20220811140530-2.png]]
204 -
205 -**4）Registers list**
206 -
207 -[[image:image-20220811102219-3.png]]
208 -
209 -**HMI software configuration**
210 -
211 -**1）HMI programming software**
212 -
213 - [[image:image-20220810171237-4.png]]
214 -
215 -**2）New HMI project**
216 -
217 -Click New Project and select the HMI model.
218 -
219 -[[image:image-20220810172010-5.png]]
220 -
221 -**3）Set communication port parameters**
222 -
223 -Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
224 -
225 -HMI IP address：192.168.39.201
226 -
227 -default gateway：192.168.39.1
228 -
229 -subnet mask：255.255.255.0
230 -
231 -[[image:image-20220811170753-2.png]]
232 -
233 -Next, click Communication Settings to configure the IP of the HMI communication object.
234 -
235 -[[image:image-20220811163047-1.png]]
236 -
237 -**hardware connection**
238 -
239 -**1）Hardware wiring diagram**
240 -
241 -This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
242 -
243 -[[image:image-20220811170248-1.png]]
244 -
245 -The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
246 -
247 -(% style="text-align:center" %)
248 248  [[image:1624348978863-771.png||queryString="width=812&height=494" height="487" width="800" class="img-thumbnail"]]
249 249  
250 -= **Rockwell PLC** =
61 +(% class="wikigeneratedid" %)
62 +== ==
251 251  
64 +(% class="wikigeneratedid" %)
252 252  == **Communication with Allen-Bradley CompactLogix L1769** ==
253 253  
67 +=== **Overview** ===
68 +
254 254  (((
255 -(((
256 256  This example introduces the establishment of Ethernet communication between Wecon V-box and Allen-Bradley L1769. It is introduced through three parts: PLC software configuration, V-box software configuration, and hardware wiring.
257 257  )))
258 258  
73 +(((
259 259  
260 260  )))
261 261  
262 262  (((
263 -(% class="wikigeneratedid" id="HSoftwareconfigurationofPLC" %)
264 -(((
265 -**Software configuration of PLC**
266 -)))
78 +== **1 Software configuration of PLC** ==
267 267  
268 -(% class="wikigeneratedid" id="HPLCprogrammingsoftware" %)
269 -(((
270 -**1）PLC programming software**
271 -)))
80 +=== **1.1 PLC programming software** ===
272 272  
273 -[[image:image-20220714162600-1.png]]
82 + [[image:image-20220714113935-3.png]]
274 274  
275 -(% class="wikigeneratedid" id="HNewPLCproject" %)
84 +=== **1.2 New PLC project** ===
85 +
276 276  (((
277 -**2）New PLC project**
87 +Click New Project and select the PLC model.
278 278  )))
279 279  
280 280  (((
281 -(((
282 -Click New Project and select the PLC model.
91 + [[image:image-20220714114247-4.png]]
283 283  )))
284 -)))
285 285  
286 286  (((
287 -[[image:image-20220714162617-2.png]]
95 + [[image:image-20220714114257-5.png]]
288 288  )))
289 289  
290 290  (((
291 291  
292 -
293 -[[image:image-20220714162652-4.png]]
294 294  )))
295 295  
296 296  (((
297 -(% class="wikigeneratedid" id="HSetEthernetparameters" %)
298 -(((
299 -**3）Set Ethernet parameters**
300 -)))
103 +=== **1.3 Set Ethernet parameters** ===
301 301  
302 302  (((
303 -(((
304 -(((
305 305  Follow the steps below to configure Ethernet parameters
306 306  )))
307 -)))
308 -)))
309 309  
310 310  (((
311 -(((
312 -(((
313 313  PLC IP address：192.168.40.101
314 314  )))
315 -)))
316 -)))
317 317  
318 318  (((
319 -(((
320 -(((
321 321  default gateway：192.168.40.1
322 322  )))
323 -)))
324 -)))
325 325  
326 326  (((
327 -(((
328 -(((
329 329  subnet mask：255.255.255.0
330 330  )))
331 -)))
332 -)))
333 333  
334 334  (((
335 -[[image:image-20220714162713-5.png]]
122 + [[image:image-20220714115012-6.png]]
336 336  )))
337 337  
338 338  (((
... ... @@ -340,121 +340,55 @@
340 340  )))
341 341  
342 342  (((
343 -(% class="wikigeneratedid" id="HV-boxsoftwareconfiguration" %)
344 -(((
345 -**V-box software configuration**
346 -)))
130 +== **2.V-box software configuration** ==
347 347  
348 -(% class="wikigeneratedid" id="HV-boxprogrammingsoftware" %)
349 -(((
350 -**1）V-box programming software**
351 -)))
132 +=== **2.1. V-box programming software** ===
352 352  
353 -(% class="wikigeneratedid" %)
354 -(((
355 - [[image:image-20220714162725-6.png]]
356 -)))
134 + [[image:image-20220714115214-7.png]]
357 357  
358 -(% class="wikigeneratedid" id="HConfiguredevicenetwork" %)
359 -(((
360 -**2）Configure device network**
361 -)))
362 362  
137 +=== **2.2. Configure device network** ===
138 +
363 363  (((
364 -(((
365 -(((
366 366  Click the Configuration Download button[[image:image-20220714115308-8.png||height="22" width="15"]], It is used to configure the device network, update the device time, obtain the device machine code, check the device network, etc.
367 367  )))
368 368  
369 369  (((
370 -In the example below, the IP address of V-Box is configured as 192.168.40.66, and the networking method is 4G connection
144 +In the example below, the IP address of V-Box is configured as 192.168.40.66, and the networking method is 4G connection.
371 371  )))
146 +
147 + [[image:image-20220714115440-9.png||height="425" width="791"]]
372 372  )))
373 373  )))
374 374  
375 -(((
376 -(((
377 -[[image:image-20220714162737-7.png]]
378 -
379 -
151 +== **2.3. V-net add device** ==
380 380  )))
381 -)))
382 -)))
383 -)))
384 384  
385 -(% class="wikigeneratedid" id="HV-netadddevice" %)
386 386  (((
387 -**3）V-net add device**
155 +Open VNET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the device machine code/product code, device password, and device alias to add the device. 
388 388  )))
389 -)))
390 390  
391 391  (((
392 -(((
393 -Open VNET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the device machine code/product code, device password, and device alias to add the device.   [[image:image-20220714162752-8.png]]
159 + [[image:image-20220714115640-10.png||height="430" width="797"]]
394 394  )))
395 395  
162 +(((
396 396  
397 397  )))
398 398  
399 399  (((
400 -(% class="wikigeneratedid" id="HSetcommunicationportparameters" %)
401 -(((
402 -**4）Set communication port parameters**
403 -)))
167 +=== **2.4. Set communication port parameters** ===
404 404  
405 -(((
406 406  In the device list on the left, find the Vbox that communicates with the L1769, click it and select configuration,communication port configuration in the main interface to add a communication protocol.
407 -)))
408 408  
409 -[[image:image-20220714162805-9.png]]
171 + [[image:image-20220714115848-11.png||height="432" width="802"]]
410 410  )))
411 411  
412 -(((
174 +
413 413  The communication port is selected as Ethernet, the device type is selected as Allen-Bradley, the protocol is Allen-BradleyMicro850_FreeTag EthemetIP, and the IP is the internal IP address of the L1769 PLC. The port number is 44818.
414 -)))
415 415  
416 -[[image:image-20220714162814-10.png]]
417 417  
418 418  
419 -(((
420 -After adding the protocol Allen-BradleyMicro850_FreeTag, click[[image:image-20220714143838-2.png]]icon add label.[[image:image-20220714162827-11.png]]
421 -)))
422 -
423 -(% class="wikigeneratedid" id="HEngineeringproduction" %)
424 -(((
425 -**5）Engineering production**
426 -)))
427 -
428 -(% class="wikigeneratedid" %)
429 -(((
430 -(((
431 -According to your own needs, use the V-NET client software to edit the required data monitoring points.
432 -)))
433 -
434 -[[image:image-20220714162841-12.png]]
435 -
436 -
437 -(((
438 -**hardware connection**
439 -)))
440 -)))
441 -
442 -(((
443 -**1）Hardware wiring diagram**
444 -)))
445 -
446 -(((
447 -(((
448 -This example introduces Wecon V-box with Allen-Bradley L1769 PLC to establish communication through Ethernet. The connection diagram is as follows:
449 -)))
450 -
451 -[[image:image-20220714162856-13.png]]
452 -
453 -(((
454 -The above are all the steps for establishing Ethernet communication between Wecon V-box with Allen-Bradley L1769 PLC.
455 -)))
456 -)))
457 -
458 458  == **Siemens S7-1200** ==
459 459  
460 460  [[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20S7-1200%20via%20Ehernet.zip]]
... ... @@ -493,7 +493,7 @@
493 493  
494 494  = **2 User define protocol** =
495 495  
496 -More serial port script instruction,please refer manual:[[Lua script function>>doc:V-BOX.V-Net.Manual.04 Lua Script.01 Lua Functions.WebHome]]~-~-->[[3.Serial port operation>>url:http://docs.we-con.com.cn/wiki/vbox/view/HMI/04.Lua%20script%20%20function%20and%20operation/01.Lua%20script%20function/#H3.Serialportoperation]]
217 +More serial port script instruction,please refer manual:[[Lua script function>>doc:V-BOX.V-Net.1\.User Manual.04 Lua Script.01 Lua Functions.WebHome]]~-~-->[[3.Serial port operation>>url:http://docs.we-con.com.cn/wiki/vbox/view/HMI/04.Lua%20script%20%20function%20and%20operation/01.Lua%20script%20function/#H3.Serialportoperation]]
497 497  
498 498  == **Read the temperature sensor.** ==
499 499  
image-20220714143820-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -1.4 MB
Content
image-20220714143838-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -520 bytes
Content
image-20220714143849-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -1.3 MB
Content
image-20220714160006-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -1.3 MB
Content
image-20220714160034-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -135.2 KB
Content
image-20220714160120-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.8 KB
Content
image-20220714160335-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -264.1 KB
Content
image-20220714160412-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.5 KB
Content
image-20220714160439-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -104.0 KB
Content
image-20220714160541-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.7 KB
Content
image-20220714160651-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -135.2 KB
Content
image-20220714160843-9.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -165.9 KB
Content
image-20220714160943-10.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -50.2 KB
Content
image-20220714161014-11.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -94.3 KB
Content
image-20220714161120-12.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -94.3 KB
Content
image-20220714161229-13.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -62.5 KB
Content
image-20220714161445-14.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -131.2 KB
Content
image-20220714162600-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.8 KB
Content
image-20220714162617-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -1.3 MB
Content
image-20220714162629-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.5 KB
Content
image-20220714162652-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -58.5 KB
Content
image-20220714162713-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -104.0 KB
Content
image-20220714162725-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -13.7 KB
Content
image-20220714162737-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -135.2 KB
Content
image-20220714162752-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -135.2 KB
Content
image-20220714162805-9.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -165.9 KB
Content
image-20220714162814-10.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -50.2 KB
Content
image-20220714162827-11.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -94.3 KB
Content
image-20220714162841-12.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -62.5 KB
Content
image-20220714162856-13.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -131.6 KB
Content